metal bedframe

Document technical information

Format pdf
Size 871.0 kB
First found Jun 21, 2016

Document content analisys

Language
English
Type
not defined
Concepts
no text concepts found

Transcript

: metal bedframe
assembly instructions
A
B
24x
bolt: 1/4”DIA x 3/4”
4x
bolt: 1/4”DIA x 3/8”
C
D
metal washer
1x
wrench
E
F
lock washer
G
nut
28x
H
32x
4x
stopper
8x
I
foot
2x
6298749/6298756/7001761/7001696/6298566/6298699/7001399/7001621/7322423- 07/05
allen key
1x
page 1 of 6
: metal bedframe
assembly instructions
! Do not throw away packaging materials until
assembly is complete.
footboard
! Assemble this item on a soft surface, such as
cardboard or carpet, to protect the finish.
center leg (x2)
headboard
right corner bracket (x2)
left corner bracket (x2)
side rails (2x)
midbeam
bedslats
6298749/6298756/7001761/7001696/6298566/6298699/7001399/7001621/7322423- 07/05
page 2 of 6
: metal bedframe
assembly instructions
1. Insert the connectors on the footboard into the side rails. Insert metal washer (D) and lock
washer (E) with bolt (A). Tighten with allen key (I).
2. Repeat step 1 with the headboard.
8x
D
E
A
I
6298749/6298756/7001761/7001696/6298566/6298699/7001399/7001621/7322423- 07/05
page 3 of 6
: metal bedframe
assembly instructions
3. Attach the center legs to the midbeam as shown with bolt (A), metal washers (D) locking washer (E), and
nut (F) . Tighten with allen key (I) and wrench (C).
4. Attach the midbeam to the ledges on the inside center of the headboard and footboard with bolt (B), metal
washer (D) and locking washer (E). Tighten with allen key (I). Adjust feet (H) on center legs as needed.
4x
4x
A
E
D
D
E
D
F
C
H
B
I
6298749/6298756/7001761/7001696/6298566/6298699/7001399/7001621/7322423- 07/05
page 4 of 6
: metal bedframe
assembly instructions
5. Attach corner brackets as shown. Insert metal washer (D) and lock washer (E) with bolt (A) through
side rail and into stopper (G). Tighten with allen key (I).
6. Next, insert metal washer (D) and lock washer (E) with bolt (A) into end-board. Tighten with
allen key (I).
7. Repeat steps 5 and 6 at each corner.
8. Attach stoppers (G) to top side of midbeam as shown. Insert metal washer (D) and lock washer (E)
with bolt (A) through side rail and into stopper (G). Tighten with allen key (I).
G
4x
4x
G
D
D
E
D
A
E
I
I
A
E
A
I
6298749/6298756/7001761/7001696/6298566/6298699/7001399/7001621/7322423- 07/05
page 5 of 6
: metal bedframe
assembly instructions
9. Install slats. Position the bedslats as shown. The stoppers at each end of the bed prevent the bedslats
from moving.
CARE INSTRUCTIONS.
Hardware may loosen over time. Periodically check that all
connections are tight.
Headboards are designed for placement against a wall.
Moisten a clean, soft cloth with undiluted white or cider
vinegar and wipe the surface clean. To remove streaks or
stains, dampen a clean, soft cloth with club soda and rub
the surface.
Do not use harsh abrasives or steel wool on stainless steel,
as they will create a network of tiny scratches on the surface.
As with other stainless steel products, such as cookware
and tools, some scratches are inevitable and should be
regarded as part of the natural patina.
6298749/6298756/7001761/7001696/6298566/6298699/7001399/7001621/7322423- 07/05
page 6 of 6

Similar documents

×

Report this document