AirCycler®g2-k brochure here. - Green South Energy Solutions

Document technical information

Format pdf
Size 1.5 MB
First found May 22, 2018

Document content analysis

Category Also themed
Language
English
Type
not defined
Concepts
no text concepts found

Persons

Organizations

Places

Transcript

AirCycler® g2-k
Whole House Mechanical Ventilation System
AirCycler® g2 Controller + FanConnect™ Switch + Fresh Air Damper
The AirCycler® g2-k provides the most economical solution to whole-house mechanical
ventilation by combining the best aspects of both central fan integrated ventilation and
exhaust fan ventilation.
How does the AirCycler® g2-k work?
Anytime the home’s central fan is turned on by the thermostat to
provide heating or cooling, the AirCycler® g2 opens the fresh air
damper to let in a measured amount of fresh air. The fresh air is
then distributed uniformly throughout the home. Once the
ventilation requirements are met, the damper is closed to prevent
over-ventilation.
Should normal heating and cooling cycles not run long enough to
provide the required ventilation, the AirCycler® g2 will power on
the smaller and more economical exhaust fan, typically an existing
bath fan, to provide the remaining ventilation. With no need to run
the large central furnace to provide additional ventilation,
homeowner complaints of cold air or noisy operation are
eliminated and efficiency is drastically improved.
EXAMPLE
According to codes, you must add 30 CFM of continuous ventilation. You
measure 90 CFM from the fresh air duct to the air handler. You measure 60 CFM
exhausted from the bath fan. You can spend a lot of money on a HRV or ERV, or
simply let the AirCycler® g2 use what you already have.
•
Direct replacement for the
AirCycler® FRV ventilation
controller.
•
Provides precise ventilation
control for ultimate
•
Simple set-up with our
patented new algorithm.
•
Works with any 24VAC
damper.
•
Can control a 110VAC
exhaust fan.*
•
Provides bath fan delay
timer functions.*
•
Allows for programmable
hours of operation.
One Hour of Ventilation
0
minutes
15
minutes
30
minutes
60
minutes
45
minutes
HRV/ERV System
HRV/ERV at 30 CFM continuous for 60 minutes = 1,800 CF of fresh air
VS
Central
Fan
AirCycler® g2-k
90 CFM of fresh air
during15 minutes
of heating/cooling
= 1,350 CF
Exhaust
Fan
60 CFM
for 7.5
minutes
1,800 CF of fresh air required - 1,350 CF provided during heating/cooling = 450 CF still needed
450 CF / 60 CFM = 7.5 minutes of exhaust time required to meet the ventilation demand for that hour.
®
www.aircycler.com
*If used with the optional
FanConnect™ switch
This product may be protected by one or more of the following
patents and patents pending: 8185244, 7258280, 6431268,
881806, 547017, Canada 2245135
TWO SETUP OPTIONS
Calculated Flow
If you know the amount of fresh air that goes into
the air handler as well as the flow required by
code, you can simply enter them into the
AirCycler® g2 controller during set up. The g2
will do the rest.
Calculated Time
If you’d prefer to configure the amount of time
you want fresh air ventilation per hour, you can
enter the total minutes per hour into the
AirCycler® g2. The g2 will do the rest.
Calculated Flow
Setup
NORMAL OPERATION DISPLAY
THE DAMPER
IS OPEN
THE EXHAUST
FAN IS ON
THE THERMOSTAT
HAS TURNED ON
THE CENTRAL FAN
THE AIRCYCLER® G2
HAS FORCED THE FAN
PERCENTAGE OF
VENTILATION COMPLETE
AirCycler® g2
Operating Voltage:
24 VAC (up to 30 VAC max)
Calculated Time
Setup
Current Draw:
0.07 Amps
Enter measured outside
@HQƦ[email protected]@MCKDQ
Enter required minutes per
[email protected]
Enter measured
[email protected]ƦNV
FanConnect™ Switch
Light:
450 Watts @ 120 VAC (blue wire)
*If connecting a FanConnect™ switch
Enter required continuous
@HQƦNVQDPTHQDCAXBNCD
[email protected]
[email protected]
Fan:
150 Watts @ 120 VAC (red wire)
*If connecting a FanConnect™ switch
Operation:
120 VAC ± 10%
Enter optional
mix time
NO
#[email protected]
[email protected]
GNTQR
2DSCDRHQDCGNTQR
[email protected]
Set current
time
YES
Part No.
Description
ACG2
AirCycler® g2 controller
ACG2K-04
AirCycler® g2-k
Whole-House
Ventilation Kit with
4” Damper
ACG2K-06
AirCycler® g2-k
Whole-House Ventilation
Kit with 6” Damper
ACG2K-08
AirCycler® g2-k
Whole-House Ventilation
Kit with 8” Damper
ACG2K-10
AirCycler® g2-k
Whole-House Ventilation
Kit with 10” Damper
ACFCS
FanConnect™ Switch
[email protected]
*If connecting a FanConnect™ switch
END
Begin normal
operation

Similar documents

×

Report this document