01 DG308AA(x)/883B

Document technical information

Format pdf
Size 20.1 kB
First found May 22, 2018

Document content analysis

Category Also themed
Language
English
Type
not defined
Concepts
no text concepts found

Persons

Organizations

Places

Transcript

SCOPE: QUAD, SPST, CMOS, TTL-Compatible Analog Switches
Device Type:
-01
-02
Generic Number:
DG308AA(x)/883B
DG309A(x)/883B
Case Outline(s).
Outline Letter
Mil-Std-1835
K
GDIP1-T16 or CDIP2-T16
Case Outline
16 LEAD CERDIP
Package Code
J16
Absolute Maximum Ratings
V+ to V- ..................................................................................................................................... 44V
V+ to GND ................................................................................................................................. 25V
Digital Input Overvoltage Range .....................................................…….….. (V- -2V) to (V+ +2V)
or 20mA (whichever comes first)
Current (any terminal except S or D) ..........................................................................……..... 30mA
Continuous Current, S or D .........................................................................................………. 20mA
(Pulsed at 1ms, 10% duty cycle max) ...................................................................……... 70mA
Lead Temperature (soldering, 10 seconds) ....................................................................…….... +300°C
Storage Temperature .......................................................................................…….... -65°C to +150°C
Continuous Power Dissipation ........................................................................…………….. TA=+70°C
16 lead CERDIP(derate 10mW/°C above +70°C) ................................................……………. 800mW
Junction Temperature TJ .................................................................................…………….... +150°C
Thermal Resistance, Junction to Case, ΘJC:
Case Outline 16 lead CERDIP.............................................................……………... 50°C/W
Thermal Resistance, Junction to Ambient, ΘJA:
Case Outline 16 lead CERDIP..........................................................…………….... 100°C/W
Recommended Operating Conditions.
Ambient Operating Range (TA) ...........................................................…………... -55°C to +125°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage
to the device.These are stress ratings only, and functional operation of the device at these or any
other conditions beyond those indicated in the operational sections of the specifications is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
----------------------------
Electrical Characteristics of DG308A/309/883B
19-0060
Page 2 of
Rev. B
5
TABLE 1. ELECTRICAL TESTS:
TEST
Symbol
Analog-Signal
Range
Drain-Source On
Resistance
Source-Off Leakage
Current
Source-Off Leakage
Current
Drain-Off Leakage
Current
Drain-Off Leakage
Current
Drain-On Leakage
Current
Drain-On Leakage
Current
Input Current with
Voltage High
Input Current with
Voltage Low
Positive Supply
Current
Negative Supply
Current
DYNAMIC
Turn-On Time
VANALOG
tON
Figure 1, NOTE 1
Turn-Off Time
tOFF
Figure 1, NOTE 1
rDS(ON)
CONDITIONS
-55°C≤TA≤+125°C
V+=15V, V-=-15V, GND=0V,
VINH=11V, VINL=3.5V
Unless otherwise specified
VS=±15V
GROUP A
Subgroup
Device
type
1,2,3
All
All
IS(OFF)
IS=1mA, VD=±10V, VIN=11V
(DG308A), VIN=3.5V (DG309)
VIN=3.5V, VS=+14V, VD=-14V
IS(OFF)
VIN=11V, VS=-14V, VD=+14V
ID(OFF)
VIN=3.5V, VS=+14V, VD=-14V
ID(OFF)
VIN=11V, VS=-14V, VD=+14V
ID(ON)
VIN=11V, VS=VD=+14V
ID(ON)
VIN=3.5V, VS=VD=-14V
IINH
VIN=15V
1,3
2
1
2
1
2
1
2
1
2
1
2
1
2
1,2
IINL
VIN=0V
1,2
All
I+
All channels on or off
VIN=0V or 15V
All channels on or off
VIN=0V or 15V
1,3
2
1,3
2
All
9
10,11
9
10,11
All
I-
Limits
Min
Limits
Max
-15
01
-1
-100
-1
-100
-1
-100
-1
-100
-2
-200
-2
-200
02
01
02
01
02
All
-------------------------------------
IN3
D3
S3
NC
V+
S2
D2
IN2
All
100
150
1
100
1
100
1
100
1
100
2
200
2
200
1.0
Ω
DG309
LOGIC
0
1
SWITCH
ON
OFF
of
Rev. B
5
nA
nA
nA
nA
nA
µA
µA
µA
200
400
150
350
SWITCH
OFF
ON
nA
µA
-10
-100
All
19-0060
Page 3
V
10
100
DG308A
LOGIC
0
1
Electrical Characteristics of
DG308A/309/883B
15
-1.0
NOTE 1: Figure 1, See Commercial datasheet.
PIN CONFIGURATIONS:
16-Pin CERDIP
1
IN1
9
2
D1
10
3
S1
11
4
V12
5
GND
13
6
S4
14
7
D4
15
8
IN4
16
Units
ns
ns
ORDERING INFORMATION:
01
J16
DG308AAK/883B
02
J16
DG309AK/883B
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with Mil-Prf-38535, Appendix A as
Specified in Mil-Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C, minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883,
Including Groups A, B, C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883.
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2.
ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Interim Electric Parameters
Method 5004
Final Electrical Parameters
Method 5005
Group A Test Requirements
Method 5005
Group C and D End-Point Electrical Parameters
Method 5005
Subgroups
Per Method 5005, Table 1
1
1*, 2, 3, 9
1, 2, 3, 9, 10**, 11**
1
* PDA applies to Subgroup 1 only.
** Subgroups 10 and 11, if not tested, shall be guaranteed to the limits in Table 1.
-------------------------------------
Electrical Characteristics of
DG308A/309/883B
19-0060
Page
4 of
Rev. B
5

Similar documents

×

Report this document