POSIDRIVE® FDS 5000 Projecting manual Installation Connecting

Document technical information

Format pdf
Size 3.8 MB
First found Jun 9, 2017

Document content analysis

Language
English
Type
not defined
Concepts
no text concepts found

Persons

Organizations

Places

Transcript

POSIDRIVE® FDS 5000
Projecting manual
Installation
Connecting
Accessories
V 5.6-K or later
07/2014
en
Table of contents
Projecting manual POSIDRIVE® FDS 5000
Table of contents
WE KEEP THINGS MOVING
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
5
1.1
Purpose of the manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
1.2
Other manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
1.3
Further support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
2 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
2.1
Component part of the product . . . . . . . . . . . . . . . . . . . . . .
6
2.2
Operation in accordance with its intended use . . . . . . . . . .
6
2.3
Risk assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
2.4
Ambient conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.5
Qualified personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.6
Transportation and storage . . . . . . . . . . . . . . . . . . . . . . . . .
8
2.7
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . .
8
2.8
Commissioning, operation and service . . . . . . . . . . . . . . . .
9
2.9
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
2.10 Residual dangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
2.11 UL-compliant use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
2.12 Presentation of notes on safety . . . . . . . . . . . . . . . . . . . . . .
12
3 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
3.1
General data of the inverters . . . . . . . . . . . . . . . . . . . . . . . .
13
3.1.1 Transportation, storage and operating environment . . . . . .
13
3.1.2 Device features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
3.1.3 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
3.2
Electrical data of the inverters . . . . . . . . . . . . . . . . . . . . . . .
15
3.2.1 Size 0 (BG 0): FDS 5007 to FDS 5015 . . . . . . . . . . . . . . . .
15
3.2.2 Size 1 (BG 1): FDS 5022 to FDS 5075 . . . . . . . . . . . . . . . .
16
3.2.3 Derating by increasing the switching frequency . . . . . . . . .
17
3.3
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
3.3.1 Size 0 to size 2: FDS 5007 to FDS 5150 . . . . . . . . . . . . . . .
18
ID 442269.06
Table of contents
Projecting manual POSIDRIVE® FDS 5000
Brake resistors FDS 5xxx . . . . . . . . . . . . . . . . . . . . . . . . . .
19
3.4.1 FZM, FZMU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
3.4.2 VHPR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
3.4.3 Bottom brake resistor RB 5000 . . . . . . . . . . . . . . . . . . . . . .
21
3.5
Brake resistors FDS 5xxxA . . . . . . . . . . . . . . . . . . . . . . . . .
22
3.5.1 FZMU, FZZMU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
3.5.2 GVADU, GBADU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
3.5.3 Bottom brake resistor RB 5000 . . . . . . . . . . . . . . . . . . . . . .
24
3.6
Output derater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
4 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4.1
Installation of the inverter in the switching cabinet. . . . . . . .
29
4.2
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
4.2.1 Installation of bottom brake resistor . . . . . . . . . . . . . . . . . . .
31
4.2.2 Installation of EMC shroud or brake module . . . . . . . . . . . .
33
4.2.3 Installation of terminal extension LEA 5000. . . . . . . . . . . . .
35
4.2.4 Installation of CANopen, PROFIBUS, EtherCAT or PROFINET 
accessories
37
5 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
5.1
Overview of terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
5.2
EMC connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
5.3
X10: 230 V/400 V power . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
5.3.1 Line fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
5.3.2 RCD (Residual Current Protective Devices) . . . . . . . . . . . .
46
5.3.3 Housing ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
5.3.4 Forming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
5.4
X11: 24 V power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
5.5
X1: Enable and relay 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
5.6
X20: Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
5.7
X12: ASP 5001 – Safe Torque Off . . . . . . . . . . . . . . . . . . . .
57
5.8
X2; X300 - X302; X141: Motor temperature sensor, motor holding 
brake
59
ID 442269.06
WE KEEP THINGS MOVING
3.4
3
Table of contents
Projecting manual POSIDRIVE® FDS 5000
X21: Braking resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
5.10 X22: DC link coupling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
5.11 X100-X103: Analog and binary signals . . . . . . . . . . . . . . . .
70
5.12 Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
5.12.1 X4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
5.12.2 BE encoder and BA encoder simulation . . . . . . . . . . . . . .
78
5.13 Fieldbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
5.13.1 X200: CANopen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
5.13.2 X200: PROFIBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
5.13.3 X200, X201: EtherCAT . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
5.13.4 X200, X201: PROFINET . . . . . . . . . . . . . . . . . . . . . . . . . .
83
5.14 X3: PC, USS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
84
5.15 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
5.15.1 Encoder Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
6 Examples of connections . . . . . . . . . . . . . . . . . . . . .
86
7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
88
WE KEEP THINGS MOVING
5.9
4
ID 442269.06
1
Introduction
Projecting manual POSIDRIVE® FDS 5000
1
Introduction
1.1
Purpose of the manual
This document will give you technical data and information about the installation and connection of the inverter
and its accessories. This technical documentation will enable the following personnel to perform their tasks
correctly.
• Project engineer – planning
• Electrical specialist – installation and connection
Other manuals
Manual
Contents
ID
Commissioning
Instructions FDS 5000
Reinstallation, replacement, function
test
442293
Operating manual
FDS 5000
Set up the inverter
442281
Operating manual
CANopen
Connection of the inverter to the
CANopen fieldbus system
441686
Operating manual
EtherCAT
Connection of the inverter to the
EtherCAT fieldbus system
441896
Operating manual
PROFIBUS
Connection of the inverter to the
PROBIBUS fieldbus system
441687
Operating manual
PROFINET
Connection of the inverter to the
PROFINET fieldbus system
442340
Operating manual 
ASP 5001
Integration of the safety technology with 442181
the ASP 5001 option
You can find the latest document versions at www.stoeber.de.
1.3
Further support
If you have technical questions that are not answered by this document, please contact:
• Phone: +49 7231 582-3060
• E-mail: applications@stoeber.de
If you have questions about the documentation, please contact:
• E-mail: electronics@stoeber.de
If you have questions about training sessions, please contact:
• E-mail: training@stoeber.de
ID 442269.06
WE KEEP THINGS MOVING
1.2
5
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
2
Notes on safety
The devices may cause risks. For these reasons, comply with the following:
• The safety notes listed in the following sections and points
• The technical rules and regulations.
In addition, always read the appropriate documentation. STÖBER ANTRIEBSTECHNIK GmbH & Co. KG
accepts no liability for damages caused by non-adherence to the instructions or applicable regulations.
Subject to technical changes to improve the devices without prior notice. This documentation is purely a
product description. It does not represent promised properties in the sense of warranty law.
2.1
Component part of the product
The technical documentation is a component part of a product.
•
•
Since the technical documentation contains important information, always keep it handy in the vicinity of
the device until the machine is disposed of.
If the product is sold, disposed of, or rented out, always include the technical documentation with the
product.
WE KEEP THINGS MOVING
2.2
6
Operation in accordance with its intended use
In the sense of DIN EN 50178 (previously VDE 0160), the inverters represent the electrical equipment of
power electronics for the control of power flow in high-voltage current systems. They are designed exclusively
to power asynchronous motors. Operation for purposes other than the intended use include the connection
of other electrical loads!
2.3
Risk assessment
Before the manufacturer may bring a machine onto the market, he must conduct a risk assessment according
to Machine Directive 06/42/EC. As a result, the risks associated with the use of the machine are determined.
The risk assessment is a multi-stage and iterative process. On no account can sufficient insight into the
Machine Directive be given as part of this documentation. For this reason, seek detailed information about the
norms and legal position. When installing the inverter in machines, commissioning is forbidden until it has
been determined that the machine meets the requirements of EC Directive 06/42/EC.
ID 442269.06
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
2.4
Ambient conditions
Inverters are products of the restricted sales class as described in IEC 61800-3. This product may cause highfrequency interference in residential zones and the user may be asked to take suitable measures.
The inverters are not designed for use in public low-voltage networks which power residential areas. Highfrequency interference must be expected when the inverters are used in such a network. The inverters are
only intended for use in TN networks. The inverters are only designed for use on supply current networks
which can delivery at the most a maximum of symmetrical rated short circuit current at 480 Volts as per the
following table:
Size
Max. symmetrical rated short circuit current
BG 0 and BG 1
5000 A
Install the inverter in a switching cabinet in which the permissible ambient temperature is not exceeded (see
mounting instructions).
The following applications are prohibited:
• Use in potentially explosive areas
• Use in environments with harmful substances as per EN 60721 (e.g., oils, acids, gases, fumes, powders,
irradiation)
• Use with mechanical vibration and impact stresses which exceed the information in the technical data of
the projecting manuals.
2.5
Qualified personnel
Since the devices may harbor residual risks, all configuration, transportation, installation and commissioning
tasks including operation and disposal may only be performed by trained personnel who are aware of the
possible risks.
Personnel must have the qualifications required for the job. The following table lists examples of occupational
qualifications for the jobs:
Activity
Possible occupational qualifications
Transportation and storage
Worker skilled in storage logistics or comparable
training
Configuration
- Graduate engineer (electro-technology or
electrical power technology)
- Technician (m/f) (electro-technology)
Installation and connection
Electronics technician (m/f)
Commissioning 
(of a standard application)
- Technician (m/f) (electro-technology)
- Master electro technician (m/f)
ID 442269.06
WE KEEP THINGS MOVING
Implementation of the following applications is only permitted when STÖBER ANTRIEBSTECHNIK GmbH &
Co. KG has been contacted first for permission:
• Use in non-stationary applications
7
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
Activity
Possible occupational qualifications
Programming
Graduate engineer (electro-technology or
electrical power technology)
Operation
- Technician (m/f) (electro-technology)
- Master electro technician (m/f)
Disposal
Electronics technician (m/f)
In addition, the valid regulations, the legal requirements, the reference books, this technical documentation
and, in particular, the safety information contained therein must be carefully
• read
• understood and
• complied with
2.6
Transportation and storage
Immediately upon receipt, examine the delivery for any transportation damages. Immediately inform the
transportation company of any damages. If damages are found, do not commission the product. If the device
is not to be installed immediately, store it in a dry, dust-free room. Please see the documentation for how to
commission an inverter after it has been in storage for a year or longer.
2.7
Installation and connection
WE KEEP THINGS MOVING
Installation and connection work are only permitted after the device has been isolated from the power!
8
The accessory installation instructions allow the following actions during the installation of accessories:
• The housing in the upper slot can be opened.
Opening the housing in another place or for other purposes is not permitted.
Use only copper conductors. For the line cross sections to be used, refer to DIN VDE 0298-4 or DIN EN
60204-1 Appendix D and Appendix G.
The permissible protection class is protective ground. Operation is not permitted unless the protective
conductor is connected in accordance with the regulations.
Comply with the applicable instructions for installation and commissioning of motor and brakes.
Main equipment grounding markings: The main ground connections are marked "PE" or with the international
ground symbol (IEC 417, Symbol 5019
).
The motor must have an integrated temperature monitor with basic isolation in acc. with EN 61800-5-1 or
external motor overload protection must be used.
ID 442269.06
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
Protect the device from falling parts (pieces of wire, leads, metal parts, and so on) during installation or other
tasks in the switching cabinet. Parts with conductive properties inside the inverter can cause short circuits or
device failure.
Note for UL-compliant use additionally 2.11.
2.8
Commissioning, operation and service
Remove additional coverings before commissioning so that the device cannot overheat. During installation,
provide the free spaces specified in the projecting manuals to prevent the inverter from overheating.
The housing of the inverter must be closed before you turn on the supply voltage. When the supply voltage is
on, dangerous voltages can be present on the connection terminals and the cables and motor terminals
connected to them. Remember that the device is not necessarily de-energized after all indicators have gone
off.
Before carrying out any work on the machine, observe all the following five safety regulations in the abovementioned sequence:
1. Enable. Ensure that you also activate the auxiliary circuits.
2. Secure against switching on.
3. Ensure that the parts are de-energized.
4. Earth and short-circuit.
5. Cover or isolate any live neighboring parts.
Information
Please note that the discharge time for the intermediate circuit
capacitors is 5 min. You can only ensure that the parts are deenergized after this time.
You can then start your work on the inverter. Repairs may only be performed by STÖBER
ANTRIEBSTECHNIK GmbH & Co. KG.
Send defective devices together with a fault description to:
STÖBER ANTRIEBSTECHNIK GmbH & Co. KG
Department VS-EL
Kieselbronner Str.12
75177 Pforzheim
GERMANY
ID 442269.06
WE KEEP THINGS MOVING
When network voltage is applied, the following are prohibited:
• Opening the housing
• Connecting or disconnecting the connection terminals
• Installing accessories
9
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
2.9
Disposal
Please comply with the latest national and regional regulations! Dispose of the individual parts separately
depending on their nature and currently valid regulations such as, for example:
• Electronic scrap (PCBs)
• Plastic
• Sheet metal
• Copper
• Aluminum
2.10
Residual dangers
The connected motor can be damaged with certain settings of inverters:
• Longer operation against an applied motor halting brake
• Longer operation of self-cooled motors at slow speeds
Drives can reach dangerous excess speeds (e.g., setting of high output frequencies for motors and motor
settings which are unsuitable for this). Secure the drive accordingly.
2.11
UL-compliant use
Additional information for use under UL conditions (UL – Underwriters Laboratories).
WE KEEP THINGS MOVING
Surrounding temperature and pollution degree
The maximum surrounding temperature for UL-compliant operation is 45 °C. 
Observe the specifications in the general data for use in an environment with pollution degree, see section 3.1.1.
10
Power grid type
All device types that are supplied with 480 V are designed exclusively for operation on Wye sources with 
480/277 V.
Power supply and motor overload protection
Observe the specifications in the electrical data of the inverter for this, see section 3.2.
Line fuse 
Observe the specifications for the UL-compliant line fuse in section 5.3.1.
Motor protection
All models of STOBER 5th generation inverters have a certified i²t model, a calculation model for thermal
monitoring of the motor. This fulfills the requirements for semiconductor motor overload protection in
accordance with the change to UL 508C dated May 2013. To activate the protective function and set it up,
make the following parameter settings – which differ from the default values: U10 = 2:Warning and U11 =
1.00 s. This module can be used as an alternative or in addition to motor protection with temperature
monitoring as described in section 5.8.
ID 442269.06
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
Information
STÖBER ANTRIEBSTECHNIK GmbH & Co. KG recommends
using PTC thermistors as thermal motor protection.
Motor temperature sensor
All models of the 5th generation of STOBER inverters starting with HW 200 have connections for PTC
thermistors (NAT 145 °C) or KTY temperature sensors (KT84-130). Observe the terminal description X2 for
proper connection, see section 5.8.
Braking resistor
If the inverters will be fitted with an externally mounted braking resistor, separate overtemperature protection
must be made available.
24 V power supply
Low-voltage circuits shall be supplied by an isolating source such that the maximum open circuit voltage
available to the circuit is not more than 28.8 V.
Observe terminal description X11 for this, see section 5.4.
Lines
Use only copper conductors for an surrounding temperature of 60/75 °C.
Branch circuit protection
An integral solid state short circuit protection does not provide branch circuit protection. If you would like to
branch the output of the inverter, branch circuit protection must be ensured in conformity with the instructions
of STOBER, the National Electrical Code and all additional applicable local regulations or equivalent
specifications.
UL test
During the UL acceptance process of STÖBER ANTRIEBSTECHNIK GmbH & Co. KG, only risks for electrical
shock and fire hazard were investigated. Aspects of functional safety were not assessed. These aspects are
assessed for STOBER by the TÜV SÜD certification authority, for example.
ID 442269.06
WE KEEP THINGS MOVING
Fuses
Use a 1 A fuse (time lag) upstream from relay 1. The fuse must be approved in accordance with UL 248.
Refer to the connection example of terminal description X1 for this, see section 5.5.
11
2
Notes on safety
Projecting manual POSIDRIVE® FDS 5000
2.12
Presentation of notes on safety
NOTICE
Notice
means that property damage may occur
 if the stated precautionary measures are not taken.
CAUTION!
Caution
with warning triangle means that minor injury may occur
 if the stated precautionary measures are not taken.
WARNING!
Warning
means that there may be a serious danger of death
 if the stated precautionary measures are not taken.
DANGER!
WE KEEP THINGS MOVING
Danger
12
means that serious danger of death exists
 if the stated precautionary measures are not taken.
Information
refers to important information about the product or serves to
emphasize a section in the documentation to which the reader
should pay special attention.
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3
Technical data
Product key
FDS 5075A/H
Designation
th
5 generation
Power: 075 = 7,5 kW
Hardware versions
without designation
at this point:
devices from HW 190
A: from HW 200
Device version: Auxiliary voltage for control
electronics
/H: Control electronics powered via
DC link; no additional 24 V
power neccesary
/L: Control electronics powered via 24 V
on terminal X11
3.1
General data of the inverters
3.1.1
Transportation, storage and operating environment
NOTICE
Material damage!
The DC link capacitors in devices of sizes BG 0, BG 1 and BG 2 can lose their electrical strength through long
storage times. Considerable material damage can arise from a reduced electrical strength of the DC link
capacitors when switching on.
Maximum surrounding air
temperature during operation
0 °C to 45 °C for rated data 
Up to 55 °C with power reduction, 2.5 %/K
Temperature during 
storage/transportation
-20 °C to +70 °C 
Maximum change: 20 K/h
Humidity
Relative humidity: 85 %, no condensation
Installation altitude
Up to 1000 m above sea level without restrictions 
1000 to 2000 m above sea level with power reduction, 1.5 %/100 m
Pollution degree
2 as per EN 50178
Ventilation
Built-in fan
Vibration (operation) acc. to
DIN EN 60068-2-6
5 Hz ≤ f ≤ 9 Hz: 0.35 mm 
9 Hz ≤ f ≤ 200 Hz: 1 m/s
Vibration (transportation) acc. to
DIN EN 60068-2-6
5 Hz ≤ f ≤ 9 Hz: 3.5 mm 
9 Hz ≤ f ≤ 200 Hz: 10 m/s 
200 Hz ≤ f ≤ 500 Hz: 15 m/s
ID 442269.06
WE KEEP THINGS MOVING
 Perform forming according to 5.3.4 Forming for stored devices.
13
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.1.2
Device features
Protection rating
IP 20
Interference suppression
EN 61800-3, interference emission, class C3
High-voltage category
III as per EN 61800-5-1
3.1.3
Weight
Device
Weight
Without Packaging [kg]
With Packaging [kg]
2.1
2.9
3.7
4.8
FDS 5007
FDS 5004
FDS 5008
FDS 5015
FDS 5022
FDS 5040
FDS 5055
FDS 5075
WE KEEP THINGS MOVING
If you order an inverter with accessory parts, the weight increases by the following amounts:
• Accessory parts for higher option (fieldbus): 0.1 kg
14
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.2
Electrical data of the inverters
3.2.1
Size 0 (BG 0): FDS 5007 to FDS 5015
Device
FDS 5007
FDS 5004
FDS 5008
FDS 5015
Id. no. device version /H
up to HW 190 (FDS 5xxx)
start. from HW 200 (FDS 5xxxA)
45962
55421
45961
55420
45963
55422
45964
55423
Id. no. device version /L
up to HW 190 (FDS 5xxx)
start. from HW 200 (FDS 5xxxA)
49295
55413
49294
55412
49296
55414
49297
55415
0.75 kW
0.37 kW
0.75 kW
1.5 kW
Recommended motor power
Input voltage
(L1–N) 1  230 V
+20 %/–40 %
50/60 Hz
Input rated current
Id. 45962/49295: Id. 45961/49294: Id. 45963/49296: Id. 45964/49297:
3  3.7
32A
3  1.4 A
1  5.9 A
Id. 55421/55413: Id. 55420/55412: Id. 55422/55414: Id. 55423/55415:
34A
3  2.2 A
3  1.4 A
1  5.9 A
Output frequency
0 to 400 Hz
Output voltage
(L1–L3) 3  400 V, +32 %/–50 %, 50 Hz
(L1–L3) 3  480 V, +10 %/–58 %, 60 Hz
0 to 230 V
0 to 400 V
Id. 45962/49295: Id. 45961/49294: Id. 45963/49296: Id. 45964/49297:
34A
3  2.1 A
3  1.3 A
34A
Id. 55421/55413: Id. 55420/55412: Id. 55422/55414: Id. 55423/55415:
3  4.5 A
3  2.3 A
3  1.3 A
34A
Rated current IN
Imax
180 % for 5 s; 150 % for 30 s
Switching frequency
4 kHz (adjustable up to 16 kHz with derating, see chap. 3.2.5)
Power loss at IA = IN
80 W
a)
Power loss at IA = 0 A
High-Voltage limit value
50 W
65 W
90 W
max. 30 W
440 V
830 V
Switch-on threshold 
Brake chopper
400 V to 420 V
780 V to 800 V
Switch-off threshold 
Brake chopper
360 V to 380 V
740 V to 760 V
Ext. braking resistor RBr min
100 Ω
Id. 45961/45963/45964/49294/49296/49297: 200 Ω
Id. 55420/55422/55423/55414/55412/55415: 100 Ω
Ext. braking resistor PBr max
1.8 kW
Id. 45961/45963/45964/49294/49296/49297:3.2 kW
Id. 55420/55422/55423/55414/55412/55415: 6.4 kW
a) Depends on the connected option boards and sensors (e.g., encoder).
ID 442269.06
WE KEEP THINGS MOVING
Operation with asynchronous motor (control types U/f, SLVC, VC)
15
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.2.2
Size 1 (BG 1): FDS 5022 to FDS 5075
Device
FDS 5022
FDS 5040
FDS 5055
FDS 5075
Id. no. device version /H
up to HW 190 (FDS 5xxx)
start. from HW 200 (FDS
5xxxA)
45965
55424
45966
55425
45967
55426
45968
55427
Id. no. device version /L
up to HW 190 (FDS 5xxx)
start. from HW 200 (FDS
5xxxA)
49298
55416
49299
55417
49300
55418
49307
55419
Recommended motor power
2.2 kW
4.0 kW
5.5 kW
7.5 kW
(L1–L3) 3  400 V, +32 %/–50 %, 50 Hz
(L1–L3) 3  480 V, +10 %/–58 %, 60 Hz
Input voltage
Input rated current
1  5.3 A
3  9.3 A
3  12.3 A
Output frequency
0 to 400 Hz
Output voltage
0 to 400 V
3  15.8
Operation with asynchronous motor (control types U/f, SLVC, VC)
Rated current IN
3  5.5 A
Imax
WE KEEP THINGS MOVING
Switching frequency
16
Power loss at IA = IN
3  10 A
3  12 A
3  16 A
180 % for 5 s; 150 % for 30 s
4 kHz (adjustable up to 16 kHz with derating, see chap. 3.2.5)
110 W
170 W
180 W
Power loss at IA = 0 Aa)
max. 30 W
High-Voltage limit value
830 V
Switch-on threshold 
Brake chopper
780 V to 800 V
Switch-off threshold 
Brake chopper
740 V to 760 V
200 W
Ext. braking resistor RBr min
100 Ω
Id. 45966/49299:
100 Ω
Id. 55425/55417:
47 Ω
47 Ω
Ext. braking resistor PBr max
6.4 kW
Id. 45966/49299:
6.4 kW
Id. 55425/55417:
13.6 kW
13.6 kW
a) Depends on the connected option boards and sensors (e.g., encoder).
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.2.3
Derating by increasing the switching frequency
Based on the switching frequency, the following values of the output currents result.
Inverter
Switching frequency (Parameter B24)
8 kHz
16 kHz
FDS 5004
1.3 A
1.0 A
0.7 A
FDS 5007
4.0 A
3.0 A
2.0 A
FDS 5008
– Id. 45963/49296:
– Id. 55422/55414:
2.1 A
2.3 A
1.5 A
1.7 A
1.1 A
1.2 A
FDS 5015
– Id. 45964/49297:
– Id. 55423/55415:
4.0 A
4.5 A
3.0 A
3.4 A
2.0 A
2.2 A
FDS 5022
5.5 A
4.0 A
2.6 A
FDS 5040
10.0 A
6.0 A
3.3 A
FDS 5055
12.0 A
7.5 A
4.8 A
FDS 5075
16.0 A
10.0 A
5.7 A
WE KEEP THINGS MOVING
4 kHz
ID 442269.06
17
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.3
Dimensions
3.3.1
Size 0 to size 2: FDS 5007 to FDS 5150
d2
d1
b
w
ESC
e
h2
h1
a
I/O
EM 5000 /
BRM 5000
WE KEEP THINGS MOVING
f
18
Dimensions [mm]
Inverter
BG 0
Height
h1
300
h2a)
360
Width
w
70
Depth
d1
d2
EMC shroud
Fastening holes
BG 1
b)
157
242
175
260
Height
e
37,5
Depth
f
40
Vertical distance
a
283
Vertical distance to upper edge
b
6
a) h2 = Height incl. EMC shroud EM 5000 or brake module BRM 5000
b) d2 = Depth incl. brake resistor RB 5000
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.4
Brake resistors FDS 5xxx
3.4.1
FZM, FZMU
FZM
FZMU
400x65
250 W 300 Ω
400x65
600 W 100 Ω
40376
49010
FDS 5007
—
X
FDS 5004
X
—
FDS 5008
X
—
FDS 5015
X
—
FDS 5022
—
X
FDS 5040
—
X
FDS 5055
—
X
FDS 5075
—
X
ID no.
Type
LD
H
K
M
O
R
U
X
mm
FZM
330 x 35 77
330x35
Thermal time
constant τ
Weight Protection
rating
s
kg
4,5  9 352 367
66
44
7
40,0
ca. 1,1
IP 20
FZMU
400  65 120 6,5  12 430 485
400x65
92
64
10
40,0
ca. 2,2
IP 20
FZM(U)
R
M
O
ID 442269.06
K
X
U
U
K
M
H
øD
L
Drill pattern
WE KEEP THINGS MOVING
Type
19
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.4.2
VHPR
Type
VHPR
VHPR150V
150 W 300 Ω
VHPR150V
150 W 100 Ω
VHPR500V
400 W 47 Ω
45972
45973
45974
FDS 5007
—
X
—
FDS 5004
X
—
—
FDS 5008
X
—
—
FDS 5015
X
—
—
FDS 5022
—
X
—
FDS 5040
—
X
—
FDS 5055
—
X
—
FDS 5075
—
X
X
ID no.
Type
L
C
B
A
D
E
F
WE KEEP THINGS MOVING
mm
20
τ
Weight
s
g
Protection
rating
VHPR150V
150 W 300 Ω
212
193 ± 2
40
21
4,3
8
13
46,6
ca. 310
IP 54
VHPR150V
150 W 100 Ω
212
193 ± 2
40
21
4,3
8
13
8,1
ca. 310
IP 54
VHPR500V
400 W 47 Ω
337
317 ± 2
60
31
5,3
11,5
19,5
65,0
ca. 1020
IP 54
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.4.3
Bottom brake resistor RB 5000
Type
RB 5047
60 W
47 Ω
RB 5100
60 W
100 Ω
RB 5200
40 W
200 Ω
ID no.
44966
44965
44964
FDS 5007
—
X
X
FDS 5004
—
—
X
FDS 5008
—
—
X
FDS 5015
—
—
X
FDS 5022
—
X
—
FDS 5040
—
X
—
FDS 5055
X
X
—
FDS 5075
X
—
—
See installation on inverter (chapter 4)!
RB 5047
60 W
47 Ω
RB 5100
60 W
100 Ω
Height x width x depth [mm]
Drilling template 
corresponds to size:
300 x 62 x 18
Size 1
Thermal time constant τ [s]
Weight [g]
Length of cable [mm]
Maximum torque for studs [Nm]
Protection Rating
ID 442269.06
RB 5200
40 W
200 Ω
Size 0 and 1
Size 0
8
6
approx. 460
approx. 440
250
5
IP 40
WE KEEP THINGS MOVING
Type
21
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.5
Brake resistors FDS 5xxxA
3.5.1
FZMU, FZZMU
Type
FZMU
400x65
600 W 100 Ω
400x65
1200 W 47 Ω
49010
53895
FDS 5007A
X
—
FDS 5004A
X
—
FDS 5008A
X
—
FDS 5015A
X
—
FDS 5022A
X
—
FDS 5040A
—
X
FDS 5055A
—
X
FDS 5075A
—
X
ID no.
Type
τ
Protection rating
kW
kg
40.0
18
ca. 2.2
IP 20
FZZMU 400 x 65 40.0
36
ca. 4.2
IP 20
LD
Type
H
K
M
O
R
U
X
mm
400  65
120
6.5  12
430
485
92
64
10
FZZMU 400 x 65 400  65
120
6.5  12
426
450
185
150
10
FZMU 400 x 65
FZMU
FZZM(U)
R
M
O
X
K
U
U
R
H
øD
L
K
WE KEEP THINGS MOVING
Pulse power for < 1 s Weight
s
FZMU 400 x 65
22
FZZMU
K
U
Drill pattern
M
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.5.2
GVADU, GBADU
Type
GVADU
GBADU
210  20
150 W 100 Ω
265  30
300 W 100 Ω
335  30
400 W 47 Ω
405  30
500 W 100 Ω
55441
55442
55443
55499
FDS 5007A
X
X
—
X
FDS 5004A
X
X
—
X
FDS 5008A
X
X
—
X
FDS 5015A
X
X
—
X
FDS 5022A
X
X
—
X
FDS 5040A
—
—
X
—
FDS 5055A
—
—
X
—
FDS 5075A
—
—
X
—
Type
τ
Pulse power for < 1 s
Weight
s
kW
g
GVADU 210  20
60
3.3
300
IP 54
GBADU 265  30
60
6.6
950
IP 54
GBADU 335  30
60
8.8
1200
IP 54
GBADU 405  30
60
6.6
1450
IP 54
Type
A
H
C
D
E
F
Protection rating
G
J
K
mm

°
GVADU 210  20
210
192
20
40
18.2
6.2
2
4.3
2.5
65
GBADU 265  30
265
246
30
60
28.8
10.8
3
5.3
4
73
GBADU 335  30
335
316
30
60
28.8
10.8
3
5.3
4
73
GBADU 405  30
405
386
30
60
28.8
10.8
3
5.3
4
73
ID 442269.06
WE KEEP THINGS MOVING
ID no.
23
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.5.3
Bottom brake resistor RB 5000
Type
RB 5047
60 W
47 Ω
RB 5100
60 W
100 Ω
RB 5200
40 W
200 Ω
ID no.
44966
44965
44964
FDS 5007A
—
X
X
FDS 5004A
—
X
X
FDS 5008A
—
X
X
FDS 5015A
—
X
X
FDS 5022A
—
X
—
FDS 5040A
X
X
—
FDS 5055A
X
X
—
FDS 5075A
X
—
—
See installation on inverter (chapter 4)!
Type
RB 5047
60 W
47 Ω
RB 5100
60 W
100 Ω
Height x width x depth [mm]
Drilling template 
corresponds to size:
300 x 62 x 18
Size 1
WE KEEP THINGS MOVING
Thermal time constant τ [s]
24
Weight [g]
Length of cable [mm]
Maximum torque for studs [Nm]
Protection Rating
RB 5200
40 W
200 Ω
Size 0 and 1
Size 0
8
6
approx. 460
approx. 440
250
5
IP 40
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
3.6
Output derater
WARNING!
Risk of burns! Fire hazard! Material damage!
Output chokes can heat up to over 100 °C under permitted operating conditions.
 Take protective measures against accidental and intentional contact with the output choke.
 Make sure that no flammable material is in the vicinity of the output choke.
 Do not install output chokes under or near the inverter.
WARNING!
Fire hazard!
Using output chokes outside of the nominal data (cable length, current, frequency, etc.) can cause the chokes
to overheat.
 Always operate the chokes at no more than the nominal data.
NOTICE
Danger of machine standstill!
 If you use cables which are longer than 50 m and the cables are not from STÖBER ANTRIEBSTECHNIK
GmbH & Co. KG, the cores for the motor temperature sensor and the brake must be separate (maximum
length: 100 m).
Information
The following technical data applies for a rotary field frequency of
200 Hz. For example, this rotary field frequency is achieved with a
motor with 4 pole pairs and a nominal speed of 3000 rpm.
Always observe the specified derating for higher rotary field
frequencies.
Also observe the dependency of the cycle frequency.
ID 442269.06
WE KEEP THINGS MOVING
The motor temperature sensor evaluation is malfunctioning due to cable capacities.
25
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
Type
output derater
TEP3720-0ES41
output derater
4EP3820-0CS41
ID no.
53188
53189
Voltage range
3 x 0 to 480 V
Frequency range
Rated current 4 kHz [output derater]
0 to 200 Hz
4A
17,5 A
Max. permissible cable length with output
derater
100 m
Max. surrounding air temperature
40 °C
Design
open
Protection Rating
IP 00
Winding losses
11 W
29 W
Iron losses
25 W
16 W
Connections
Max. line cross section
Screw-type terminals
10 mm2
Approvals
WE KEEP THINGS MOVING
Projecting
Select the output chokes according to the rated currents of the motor and output chokes. In particular, observe
the derating of the output choke for rotary field frequencies higher than 200 Hz.
You can calculate the rotary field frequency for your drive with the following formula:
26
p
f = n N  -----60
f
n
p
N
Rotary field frequency in Hz
Speed in rpm
Number of pole pairs
Nominal value
ID 442269.06
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
Derating TEP3720-0ES41
IN [A]
4,5
4
3,5
3
2,5
1
2
2
1,5
1
0,5
0
1
2
0
100
200
300
400
500
600
700
f [Hz]
Cycle frequency 4 kHz
Cycle frequency 8 kHz
Derating 4EP3820-0CS41
IN [A]
20
18
16
14
10
1
2
8
6
4
2
0
1
2
0
100
200
Cycle frequency 4 kHz
Cycle frequency 8 kHz
ID 442269.06
300
400
500
600
700
f [Hz]
WE KEEP THINGS MOVING
12
27
3
Technical data
Projecting manual POSIDRIVE® FDS 5000
Type
TEP3720-0ES41
4EP3820-0CS41
h [mm]
max. 153
max. 153
w [mm]
178
178
d [mm]
73
88
a1 [mm]
166
166
a2 [mm]
113
113
b1 [mm]
53
68
b2 [mm]
49
64
e [mm]
5.8
5.8
f [mm]
11
11
Screwed glands – M
M5
M5
Weight [kg]
2.9
5.9
A
h
w
a1
a2
M 1:2
28
A
a1
b1
b2
b1
d
e
WE KEEP THINGS MOVING
f
M
Mounting borings in
acc. to DIN EN 60852-4
ID 442269.06
4
Installation
Projecting manual POSIDRIVE® FDS 5000
4
Installation
This chapter will give you information about installation. This includes:
• Installation of the inverter in the switching cabinet
• Installation of accessories on or in the inverter
WARNING!
Danger of injury/death and property damage due to electric shock!
 Before installing accessories, turn off all voltage supplies! Then wait 5 minutes for the DC link capacitors
to discharge. Never begin with accessory installation until after this!
4.1
Installation of the inverter in the switching cabinet
NOTICE
Danger of property damage from incorrect installation of the devices!
•
•
•
•
•
•
•
The inverters must be installed in the switching cabinet (protection rating IP 20 of the inverter)
The installation site must be free of dust, corrosive fumes and all kinds of liquids (as pollution degree 2 in
accordance with EN 50178).
The installation site must be free of atmospheric moisture.
Avoid condensation (e.g., use anti-condensation heating elements).
Use mounting plates with conductive surfaces (e.g., unpainted) for EMC considerations.
Secure the inverters to the mounting plate with M5 screws.
The inverters must be installed vertically:
ID 442269.06
WE KEEP THINGS MOVING
 It is essential to comply with the following installation instructions to avoid damage to the devices.
29
4
Installation
Projecting manual POSIDRIVE® FDS 5000
•
Avoid installation above or in the immediate vicinity of heat-generating devices, e.g. output chokes or
braking resistors:
•
Provide the minimum free space required so that enough air can circulate.
C
WE KEEP THINGS MOVING
B
A
C
30
Min. free space
[dimensions in mm]
A
Upwards
B
Downwards
C
Sidewards
Size 0 and size 1
100
100
5
... with EMC shroud or
brake module
100
120
5
ID 442269.06
4
Installation
Projecting manual POSIDRIVE® FDS 5000
4.2
Accessories
4.2.1
Installation of bottom brake resistor
WARNING!
Danger of injury/death and property damage due to electric shock!
 Before installing accessories, turn off all voltage supplies! Then wait 5 minutes for the DC link capacitors
to discharge. Never begin with accessory installation until after this!
Requirements:
• You have tapped holes for threaded bolts on the mounting plate in the control cabinet at the installation
location of the device as described in section 3.3 Dimensions. The threaded bolts are included with the
bottom brake resistor.
For installation you will need:
• The threaded bolts included with the bottom brake resistor
• The screws and washers included with the bottom brake resistor
• A Phillips screwdriver
Installation of the bottom brake resistor
WE KEEP THINGS MOVING
1. Attach the bottom brake resistor to the mounting plate with the threaded
bolts:
ID 442269.06
31
4
Installation
Projecting manual POSIDRIVE® FDS 5000
2. Place the device on the guides:
WE KEEP THINGS MOVING
3. Press the device down on the guides:
32
4. Attach the device to the studs with the screws and washers:
 You have installed the bottom brake resistor.
5. Connect the braking resistor.
Refer to the terminal description X21 for proper connection of the cable,
see section 5.9.
6. Parameterize the braking resistor in the inverter.
ID 442269.06
4
Installation
Projecting manual POSIDRIVE® FDS 5000
4.2.2
Installation of EMC shroud or brake module
WARNING!
Danger of injury/death and property damage due to electric shock!
 Before installing accessories, turn off all voltage supplies! Then wait 5 minutes for the DC link capacitors
to discharge. Never begin with accessory installation until after this!
You can use the EMC shroud EM 5000 to connect the cable shield of the power cable. The brake module
BRM 5000 additionally includes the power electronics for the optional brake controller for a 24 V brake. BRM
5000 and EM 5000 are identical with regard to the mechanical elements. The attachment for both accessory
parts is therefore the same and is treated in the same way in the following sections.
Prerequisites:
• You have already installed the inverter in the switching cabinet.
You will need
• A tool to unscrew the mounting screw
Installation of EMC shroud EM 5000 or brake module BRM 5000 on the
inverter
2. Slide the component into the openings at a slight angle:
ID 442269.06
WE KEEP THINGS MOVING
1. Remove the bottom mounting screw and washers from the inverter:
33
4
Installation
Projecting manual POSIDRIVE® FDS 5000
3. Press the back of the component onto the wall of the switching cabinet:
4. Attach the component to the mounting plate and inverter with the
mounting screw and the washers:
WE KEEP THINGS MOVING
 You have now installed the accessory.
34
ID 442269.06
4
Installation
Projecting manual POSIDRIVE® FDS 5000
4.2.3
Installation of terminal extension LEA 5000
WARNING!
Danger of injury/death and property damage due to electric shock!
 Before installing accessories, turn off all voltage supplies! Then wait 5 minutes for the DC link capacitors
to discharge. Never begin with accessory installation until after this!
CAUTION!
Danger of property damage due to electrostatic discharge, among others!
 Provide suitable protective measures while handling open PCBs (e.g., ESD clothing, environment free of
dirt and grease).
 Do not touch the contact surfaces.
The LEA 5000 accessory adds 8 binary inputs and 8 binary outputs to the standard terminals of the FDS 5000.
The accessory part is installed above the inverter's display.
You will need the following for installation of LEA 5000:
• The covering plate which is included with the LEA 5000 accessory
• Phillips screwdriver
1. Remove the mounting screws and take off the cover plate:
2. Disconnect the plug connectors from the terminal extension LEA 5000.
ID 442269.06
WE KEEP THINGS MOVING
Installation of a LEA 5000 in an FDS 5000
35
4
Installation
Projecting manual POSIDRIVE® FDS 5000
3. Place the plate over the base strips. Check alignment of the plate!
4. Reconnect the plug connectors to the terminal extension.
WE KEEP THINGS MOVING
5. Guide the option board into the inverter so that the gold contacts slide into
the black connector:
36
6. Secure the metal plate to the inverter with the mounting screws:
 You have now installed the accessory.
ID 442269.06
4
Installation
Projecting manual POSIDRIVE® FDS 5000
4.2.4
Installation of CANopen, PROFIBUS, EtherCAT or PROFINET
accessories
WARNING!
Danger of injury/death and property damage due to electric shock!
 Before installing accessories, turn off all voltage supplies! Then wait 5 minutes for the DC link capacitors
to discharge. Never begin with accessory installation until after this!
CAUTION!
Danger of property damage due to electrostatic discharge, among others!
 Provide suitable protective measures while handling open PCBs (e.g., ESD clothing, environment free of
dirt and grease).
 Do not touch the contact surfaces.
You will need the following for installation of CAN 5000 or DP 5000:
• A TX10 Torx screwdriver
• A pair of pliers
• Hexagon socket wrench, 4.5 mm
Installation of a CAN 5000 or DP 5000 in an inverter
1. Remove the mounting screws and take off the cover plate:
2. Remove the metal plate punch-out with a pair of pliers:
ID 442269.06
WE KEEP THINGS MOVING
You will need the following accessories for the connection of CANopen or PROFIBUS. The accessory part is
installed above the inverter's display.
• CANopen: CAN 5000
• PROFIBUS: DP 5000
37
4
Installation
Projecting manual POSIDRIVE® FDS 5000
3. Remove the screws from the option board:
4. From below, thread the sub D plug connector of the PCB through the metal
plate:
WE KEEP THINGS MOVING
5. Secure the PCB to the metal plate with the screws which you removed in
step 3:
38
6. Guide the option board into the inverter so that the gold contacts slide into
the black connector:
ID 442269.06
4
Installation
Projecting manual POSIDRIVE® FDS 5000
7. Secure the metal plate to the inverter with the mounting screws:
 You have now installed the accessory.
You will need the following accessories for the connection of EtherCAT or PROFINET. The accessory part is
installed above the inverter's display.
• EtherCAT: ECS 5000
• PROFINET: PN 5000
You will require the following for installation:
• A TX10 Torx screwdriver; a Phillips screwdriver
• the following cover plate, which is included in the accessories, is required for installing the ECS 5000:
IN
the following cover plate, which is included in the accessories, is required for installing the PN 5000:
Run
•
BF
The screw with locking disk which is included with the ECS 5000 accessories.
Installation of an ECS 5000 or PN 5000 in an inverter
1. Remove the mounting screws and take off the cover plate:
ID 442269.06
WE KEEP THINGS MOVING
•
OUT
39
4
Installation
Projecting manual POSIDRIVE® FDS 5000
2. From below, guide the RJ45 plug connector of the PCB through the metal
plate which is included with the accessory:
3. Secure the metal plate on the PCB with the included screw with locking disk:
WE KEEP THINGS MOVING
4. Guide the option board into the inverter so that the gold contacts slide into
the black connector:
40
5. Secure the metal plate on the PCB with the included screws:
 You have now installed the accessory.
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5
Connection
5.1
Overview of terminals
Front and top of the device
X10 – 230V/400 V power
X12 ASP 5001 (option)
Housing ground
X11 – 24 V power
X200, X201
fieldbus accessory
• CAN 5000
• DP 5000
• ECS 5000
• PN 5000
Terminal extension:
• LEA 5000
(X103 D, X103 E)
X3 PC, USS
X100 – X101
terminals
ID 442269.06
WE KEEP THINGS MOVING
X1 enable,
relay 1
41
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Bottom of the device
X4 Encoder
X2 Motor temperature
sensor, brake
BRM 5000: X302
X20 Motor
BRM 5000: X301
X21 Braking resistor
BRM 5000: X300
WE KEEP THINGS MOVING
X22 DC link
42
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.2
EMC connection
Information
This chapter contains general information on EMC-suitable
installation. These are only recommendations. Depending on the
application, the ambient conditions and the legal requirements,
measures in addition to this recommendations may be required.
•
•
•
•
•
•
WE KEEP THINGS MOVING
•
Install power line, motor cable and signal lines separately from each other (e.g., in separate cable ducts).
Use only shielded cables for the motor cable.
If the brake line is installed together with the motor cable, the brake line must be shielded separately.
Apply the shield of the motor cable over a large surface and in the immediate vicinity of the inverter. Use
the EMC shroud EM 5000 or the mechanically identical brake module.
Shield the cable for the connection of a brake resistor if the cable is longer than 30 cm. In this case apply
the shield over a large surface in the immediate vicinity of the inverter.
Always place the canopy with considerable spacing around the terminal box in the case of motors with
terminal boxes. You should use EMC cable connections.
Connect the shield of the control lines on one side to the reference ground of the source (e.g., the PLC or
CNC).
ID 442269.06
43
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.3
X10: 230 V/400 V power
Terminal description – single-phase power connection size 0
Pin
L1 N PE
Designation
Function
Data
nc
Plastic dummy plug
—
L1
Input voltage
230 V +20 %/-40 % 50/60 Hz
N
Neutral conductor
—
PE
Protective conductor
—
Terminal description – three-phase power connection
Pin
Designation
Size 0
Size 1
L1 L2 L3 PE
L1 L2 L3 PE
Function
Data
Input voltage
3 x 400 V +32 %/-50 % 50 Hz or
3 x 480 V +10 %/-58 % 60 Hz
Protective conductor
—
L1
L2
L3
PE
Minimum tightening torque Mmin – screw-type terminals
WE KEEP THINGS MOVING
Size
44
Size 1
Unit
[Nm]
[lb-in]
Mmin
0.5
4.4
Maximum conductor cross-section of power terminals
Size
Cross-section
[mm2]
Size 0
Size 1
2,5
4
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.3.1
Line fuse
The device's cables and output are protected by means of line protection. Various protective devices may be
used for this purpose:
• Full range fuse (class "gG" in accordance with IEC class specification or "time lag" in accordance with
VDE)
• Line circuit breaker 
Use line circuit breaker with trigger characteristics C in accordance with EN 60898.
• Power circuit breaker
Use fuses of class RK1 for UL-compliant applications, for example Bussmann KTS-R-xxA/600 V. For devices
of sizes BG 0 and BG 1 It is also possible to uses fuses of class CC.
Input current
INom
Protection rating
Recommended
For UL-compliant use
For DC link connection
in group 1
FDS 5007
1 x 5.9 A
1 x 10 A
1 x 10 A
1 x 10 A
FDS 5004
3 x 1,4 A
3x6A
3x6A
3 x 10 A
FDS 5008
3x2A
3x6A
3x6A
3 x 10 A
FDS 5015
3 x 3,7 A
3 x 10 A
3 x 10 A
3 x 10 A
FDS 5022
3 x 5,3 A
3 x 10 A
3 x 10 A
3 x 20 A
FDS 5040
3 x 9,3 A
3 x 16 A
3 x 15 A
3 x 20 A
FDS 5055
3 x 12,3 A
3 x 16 A
3 x 15 A
3 x 20 A
FDS 5075
3 x 15,8 A
3 x 20 A
3 x 20 A
3 x 20 A
The inverters are only suitable for use in supply current networks that are able to provide a maximally
symmetrical nominal short circuit current at 480 volts according to the following table:
Size
Max. symmetrical nominal short circuit current
Size 0 and size 1
5000 A
ID 442269.06
WE KEEP THINGS MOVING
Type
45
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.3.2
RCD (Residual Current Protective Devices)
The devices from STÖBER ANTRIEBSTECHNIK GmbH & Co. KG can be protected with residual current
devices (RCD) to detect residual currents.
DANGER!
Electric shock hazard!
The power rectified and its configuration can cause a smooth residual DC current.
 Always protect the devices from STOBER using AC/DC sensitive RCDs (type B).
Rating
The maximum residual current caused by an unsymmetrical feed is 40 mA.
Observe that faulty activation may result:
• When connecting devices to the supply voltage:
–
These faulty activations can be rectified by using short-time delayed (super-resistant), selective
(delayed switch-off) RCDs or RCDs with increased trigger current (e.g. 300 or 500 mA).
Information
Check whether the use of RCDs with increased trigger current as
well as with short-time delayed or delayed switch-off trigger
characteristics are permitted in your application.
•
Due to higher frequency stray currents for long motor cables under normal operating conditions:
–
WE KEEP THINGS MOVING
•
46
For example, these faulty activations can be rectified using low-capacitance cables or output chokes.
Due to unbalances in the supply network
–
For example, these faulty activations can be rectified using an isolating transformer.
Installation:
DANGER!
Electric shock hazard!
If a RCD of type AC or A is in front of one of type B in a cascaded installation, the RCD of type AC or A is
inoperative.
 Never stagger a RCD of type AC or A before a RCD of type B!
 Always observe the operating instruction of the RCD.
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.3.3
Housing ground
Note the following information on the connection of the protective earth to ground the housing correctly:
• Note the assembly sequence on the M6 earth bolts (1):
•
•
•
2 Contact disk
•
3 Cable socket
1
6
5
•
4 Washer
•
5 Return spring (optional)
•
6 Nut
3
4
2
Contact disk, washer, return spring and nuts are supplied
with the inverter.
Tightening torque: 4 Nm
Stray currents > 10 mA can arise in normal operation. 
To fulfill DIN EN 61800-5-1 and EN 60204-1, connect the earth bolts with a copper conductor according
to the following table:
Minimum cross-section SP
Earth conductor at earth bolts
S ≤ 2.5 mm2
2.5 mm2
2.5 < S ≤ 16 mm2
S
16–35 mm2
≥16 mm2
> 35 mm2
S/2
WE KEEP THINGS MOVING
Cross-section S
Feeder
ID 442269.06
47
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.3.4
Forming
NOTICE
Material damage!
The DC link capacitors in devices of sizes BG 0, BG 1 and BG 2 can lose their electrical strength through long
storage times. Considerable material damage can arise from a reduced electrical strength of the DC link
capacitors when switching on.
 Perform forming according to 5.3.4 Forming for stored devices.
L1
L2
L3
PE
Information
STÖBER ANTRIEBSTECHNIK GmbH & Co. KG recommends
connecting stored devices to the supply voltage according to the
wiring shown for one hour every year.
48
L1 L2 L3 PE
X10
L+ M
1
X11
2
3
4
M
L+
X1
X2
1
2
X21
PTC
X20
U V W PE
RB RB
X5
STÖBER ANTRIEBSTECHNIK
PTC
A1
X4
WE KEEP THINGS MOVING
F1
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
L1
L2
L3
PE
If annual forming is not possible, form the stored devices before commissioning according to the wiring and
voltage levels shown below.
F1
A1
L1 L2 L3 PE
L+ M
X10
X11
1
2
3
4
M
L+
X1
2
X21
RB RB
X5
1
PTC
X2
PTC
X20
U V W PE
X4
STÖBER ANTRIEBSTECHNIK
Power voltage [%]
75
50
25
0
0 0.5 1
2
4
Storage time 1 - 2 years:
Time [h]
6
8
Before enabling, apply voltage for
one hour.
Storage time 2 - 3 years: Before enabling, form as per curve.
Storage time 3 years:
Before enabling, form as per curve.
Storage time under 1 year: No action required.
ID 442269.06
WE KEEP THINGS MOVING
100
49
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.4
X11: 24 V power
With device version /L, connection of 24 V on X11 is required for the powering of the control unit.
NOTICE
Danger of damage to the device due to overload!
 If the 24 V power is looped through, a max. of four devices may be powered on one line.
Terminal description – size 0 and size 1
Pin
+
Designation
Function
Data
+
+ 24 V
+
+ 24 V
Auxiliary voltage (PELV) for powering the
control electronics
UE = 20.4–28.8 V IE
max = 1.5 A
–
GND
–
GND
Reference potential for +24 V
—
Maximum conductor cross-section
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
WE KEEP THINGS MOVING
Flexible with cable end, without plastic 1,5
sleeve
50
Flexible with cable end, with plastic
sleeve
0,5
2 leads with the same cross-section
with double cable end
—
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Example of connection
If the 24 V power is looped through, a max. of four devices may only be powered on one line. For conformity
with UL, a 4 A fuse must be used on the 24 V incoming line. The fuse must be approved as per UL 248.
Size 0 and size 1
Inverter
AC
4A
X11
+
+
_
_
24V
Example of the connection of two devices
Inverter
AC
4A
X11
+
+
_
_
24V
Inverter
X11
WE KEEP THINGS MOVING
+
+
_
_
ID 442269.06
51
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.5
X1: Enable and relay 1
Use the enable signal to enable the power pack of the inverter. Starting with V 5.5-C, the function of relay 1
can be adjusted in parameter F10.
Terminal description
Pin
Designation
Contact 1
2
Contact 2
3
GND
Data
Relay 1
Umax = 30 V
Imax = 1.0 A
Life expectancy (number of switching 
operations):
• Mechanical: min. of 5,000,000 switching
operations
• At 24 V/1A (ohmic load): 300,000
switching operations
Recommended fuse: max. 1 A (time lag)
Enable of the power
pack
High level ≥12 V
Low level < 8 V
IE max = 16 mA
UE max = 30 V
1 2 3 4
1
Function
4
+ Input
WE KEEP THINGS MOVING
Maximum conductor cross-section
52
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
Flexible with cable end, without plastic 1,5
sleeve
Flexible with cable end, with plastic
sleeve
0,5
2 leads with the same cross-section
with double cable end
—
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Example of connection
For a UL-compliant application, the use of a 1 A fuse before relay 1 is mandatory. The fuse must be approved
as per UL 248.
AC
+
24V
SPS
F
Inverter
X1
1
2
3
4
Relay 1
Enable
WE KEEP THINGS MOVING
E1
GND
A1
ID 442269.06
53
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.6
X20: Motor
Terminal description - size 0 and size 1
Pin
Size 0
Size 1
U
U
V
W PE
W
PE
V
Designation
Function
U
Motor connection, phase U
V
Motor connection, phase V
W
Motor connection, phase W
PE
Protective conductor
Minimum tightening torque Mmin – screw-type terminals
Size
Size 1
Unit
[Nm]
[lb-in]
Mmin
0.5
4.4
Maximum conductor cross-section of power terminals
Size
2
Cross-section [mm ]
Size 0
Size 1
2,5
4
WE KEEP THINGS MOVING
Max. cable length
Remember the maximum motor cable lengths in accordance with the following table:
54
Size
Size 0 and size 1
Without output derator
50 m
With output derator
100 m
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Connection without output choke
Observe the following points when connecting the motor without the output choke:
• Ground the shield of the motor cable with the shield connection clamp on the EMC shroud.
• Keep the exposed conductor as short as possible. All devices and circuits that are sensitive to EMC must
be kept at a distance of at least 0.3 m.
Connection with output choke
Observe the following points when connecting the motor to the output choke:
• Ground the shield of the motor cable with large area contacts in the immediate vicinity of the output choke,
for example with electrically conductive metal cable terminals on a grounded connection rail (see Fig. 5-1).
• Keep the exposed conductor as short as possible. All devices and circuits that are sensitive to EMC must
be kept at a distance of at least 0.3 m.
7 8
PE PE 1U1 1U2
Pin 7 and
8 are
bridged at
the output
derator
ID 442269.06
1V1 1V2
1W1 1W2
WE KEEP THINGS MOVING
Fig. 5-1 Example of the shield connection of the motor cable when connecting the motor with an output choke
(with friendly support from icotek GmbH, www.icotek.de)
55
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Example of connection
PES: HF shield connection via large-surface connection to PE
Inverter
X20 U
V
W PE
PES
PES
WE KEEP THINGS MOVING
M
3~
56
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.7
X12: ASP 5001 – Safe Torque Off
Information
If you are going to use this safety function, you will need the ASP
5001 option. It is imperative you read the operating instructions
ASP 5001 (see section 1.2 Other manuals) and integrate the safety
technology in your safety circuit in accordance with the description
given there. Connect the ASP 5001 option as per the following
description if you are not using any safety technology.
Information
Please remember that the following description only applies to the
ASP 5001. Go to applications@stoeber.de for the description of the
ASP 5001.
Terminal description X12
Des.
Function
Data
NC contact
(break contact
element)
Feedback contact;
must be integrated
in the safety circuit
of the controller!
Note the specifications
in the operating
instructions ASP 5001,
see section 1.2 Other
manuals.
1
2
1 2 3 4
3
Relay coil+
4
Relais coil-
Activationa)
UE = 20.4–28.8 VDC
(PELV)
IETyp = 50 mA
IE max = 70 mA
Note the specifications
in the operating
instructions ASP 5001,
see section 1.2 Other
manuals.
Circuiting 
(If safety technology is not
used!)
Inverter
X12
+
-
24V
1
2
3
4
a) To conform with UL, a 4 A delayed fuse must be used in the 24 V feeder line. The fuse must be approved in accordance
with UL 248.
ID 442269.06
WE KEEP THINGS MOVING
Pin
57
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Maximum conductor cross-section
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
Flexible with cable end, without plastic 1,5
sleeve
0,5
2 leads with the same cross-section
with double cable end
—
WE KEEP THINGS MOVING
Flexible with cable end, with plastic
sleeve
58
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.8
X2; X300 - X302; X141: Motor temperature sensor, motor
holding brake
Connect the motor temperature sensor and the power switch for controlling the motor holding brake at
terminal X2.
Motor holding brake connection
Note that the switch contact at X2 is not suitable for the direct connection of a brake. Instead use the
accessory part BRM 5000 or a suitable power switch.
Motor temperature sensor connection
You can either connect a KTY or up to two PTC drillings. The motor windings are monitored thermally using
the temperature sensors. The Ohmic resistance of the PTC changes suddenly to a value several times higher
when the nominal response temperature is reached.
Information
Please note that temperature sensor evaluation is always active. If
operation without temperature sensor is permitted, the connections
must be bridged on X2. If the connections are not bridged when the
device is switched on, a fault will be triggered.
ID 442269.06
WE KEEP THINGS MOVING
Information
Note that the evaluation of a KTY84-130 on the FDS 5000 is
possible with a hardware version of 200 or higher. Before using a
KTY, note that motor protection is not ensured to the same extent
as when monitoring with PTC drilling.
59
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description X2
Pin
Data
1
1BD1



2
1BD2
Max.
• 250 VAC/5 A
• 30 VDC/5 A (ohm. load
• 30 VDC/0.3 A (ind. load)
UL
• 30 VDC/3 A (ohm. load
TA = 1 ms
Switch time: 15 ms
Operating cycles:
• mechanical 30 000 000
• 100 000 at 250 VAC/0.6 A (ohm. load)
• 300 000 at 30 VAC/0.3 A (ohm. load)
Recommended fuse: max. 1 A (time lag)
3
1TP1/1K1 +
4
1TP2/1K2 -
1 2 3 4
Function
Max. 6 PTC (connected in series) or a KTY84130, max. cable length: 50 m
Maximum conductor cross-section
Maximum conductor cross-section [mm2]
Flexible
2,5
2,5
Flexible with cable end Flexible with cable end
without plastic sleeve
with plastic sleeve
2,5
2,5
2 conductors of the same
cross-section with double
cable end
1,5
WE KEEP THINGS MOVING
Rigid
60
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Connection of a 24 V motor halting brake and the temperature sensor with BRM 5000
You can use the optional braking module BRM 5000 to connect a 24 V motor halting brake to the inverter.
Terminal description – X300 on BRM 5000
Connect the 24 V power supply of the braking module to terminal X300.
Pin
Function
Data
+
24 V
Feedin for brake control
UE = 24–30 V
IE max = 2.5 A
–
GND
Reference potential for 24 V
—
+
Designation
Maximum conductor cross-section
Maximum conductor cross-section [mm2]
Rigid
Flexible
2,5
2,5
Flexible with cable end Flexible with cable end
without plastic sleeve
with plastic sleeve
2,5
2 conductors of the same
cross-section with double
cable end
2,5
1,5
Terminal description – X301 on BRM 5000
Connect the motor halting brake and the motor temperature sensor to terminal X301.
1 2 3 4
Designation
Function
Data
1
1BD2
Reference potential for Pin 2 —
2
1BD1
Control brake
IA max ≤ 2.5 A: max. of 10 switching
cycles per minute
3
1TP1/1K1+
Temperature sensor
4
1TP2/1K2-
Max. 6 PTC or one KTY84-130, max.
cable lenth: 50 m
Maximum conductor cross-section
Maximum conductor cross-section [mm2]
Rigid
Flexible
2,5
2,5
ID 442269.06
Flexible with cable end Flexible with cable end
without plastic sleeve
with plastic sleeve
2,5
2,5
2 conductors of the same
cross-section with double
cable end
1,5
WE KEEP THINGS MOVING
Pin
61
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description – X302 on BRM 5000
Connect terminal X302 to terminal X2 on the inverter.
Pin
5 6 7 8
Designation
Function
5
1TP2/1K2-
Temperature sensor, connect with pin 4 on X2
6
1TP1/1K1+
Temperature sensor, connect with pin 3 on X2
7
1BD2
Control brake, connect with pin 2 on X2
8
1BD1
Control brake, connect with pin 1 an X2
Maximum conductor cross-section
Maximum conductor cross-section [mm2]
Rigid
Flexible
2,5
2,5
Flexible with cable end Flexible with cable end
without plastic sleeve
with plastic sleeve
2,5
2,5
2 conductors of the same
cross-section with double
cable end
1,5
WE KEEP THINGS MOVING
Information
Remember that one LED is installed on the brake module. These
LED indicate the status of the brake control:
- LED on: brake output, energized (active)
- LED off: brake output, not energized (inactive)
62
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Brake connection with BRM 5000 for 24 V DC brake
Inverter
contact
brake relay
PTC
PTC
L+
M
F
X2
1 2 3 4
+ -
8 7 6 5
X300
X302
X301
BRM 5000 1 2 3 4
6
- +
5 7
8
brake PTC
Indirect brake control
L+
M
L
N
F
F
7
K
PowerBox
~
X2
1 2 3 4
~
-
8
K
+
- +
brake
ID 442269.06
PTC
WE KEEP THINGS MOVING
contact
brake relay
PTC
PTC
Inverter
63
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.9
X21: Braking resistor
An external braking resistor may be necessary during generating operation. For the technical data on the
braking resistors, see chapter 3.
Terminal description – size 0 and size 1
Pin
Designation
Size 0
Size 1
Function
RB
RB RB
RB RB
Connection of braking resistor
RB
Minimum tightening torque Mmin – screw-type terminals
Size
Size 1
Unit
[Nm]
[lb-in]
Mmin
0.5
4.4
Maximum conductor cross-section of power terminals
Size
Cross-section
[mm2]
Size 0
Size 1
2,5
4
WE KEEP THINGS MOVING
Example of connection
Use a shielded cable for cables longer than 30 cm between braking resistor and device.
64
Inverter
X21 RB
RB
PES
PES
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.10
X22: DC link coupling
Information
Remember that the DC link coupling described here can only be
used with the device families MDS 5000, SDS 5000 and FDS 5000.
When you have axes in your system which operate in combination and are continuously regenerative and
motor-driven, the DC link coupling may offer advantages. The DC link coupling takes the excess power and
offers it to other axes as drive power instead of converting it into heat via a braking resistor. Remember that
you will need a braking resistor to absorb the power peaks when all drives in the DC link coupling brake at the
same time.
DANGER!
Danger of device damage! When single-phase and three-phase devices are coupled, the single-phase
devices will be destroyed.
 Only use three-phase devices for the DC link coupling!
NOTICE
Danger of device damage!
 Make a note of the wiring and parameterization of relay 1 in Section Principal circuit diagram (X1.1 and
X1.2).
 After a failure, replace all the devices in a group.
Information
Remember that the parameter A38 DC power-input must be set
before the DC link coupling can function correctly:
Group 1: A38 = 0: inactive
Groups 2 and 3: A38 = 1: active
See the description of the parameter.
ID 442269.06
WE KEEP THINGS MOVING
Because the failure of one device could damage other devices, failure of a device must cause the entire DC
link compound system to be disconnected from the power supply.
65
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description X22 – size 0 and size 1
Pin
Designation
Size 0
Size 1
-U
Function
Reference potential for DC link
-U
-U +U +U
-U -U +U +U
-U
+U
+ Potential of DC link
+U
Minimum tightening torque Mmin – screw-type terminals
Size
Size 0
Size 1
Unit
[Nm]
[lb-in]
[Nm]
[lb-in]
Mmin
0,5
4,4
0,5
4,4
Maximum conductor cross-section of power terminals
Size
2
Size 1
2,5
4
WE KEEP THINGS MOVING
Cross-section [mm ]
Size 0
66
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Principal circuit diagram
The following circuit diagram shows the principal circuit diagram of the DC link coupling. The inverters can be
linked together in up to three groups. The table on the next page shows the possible combinations. The
combination determines the types of line fuses and the DC link fuse.
L1
L2
L3
PE
Power
fuse3
Group 1
Group 2
Must be integrated
in the controller!
Note the
parameterization
of the relay in F10.
X10
MDS/FDS/
SDS
1 2 X1
X10
X10
X10
MDS/FDS/
SDS
MDS/FDS/
SDS
1 2 X1
X10
1 2 X1
X10
MDS/FDS/
SDS
MDS/FDS/
SDS
1 2 X1
Group 3
MDS/FDS/
SDS
1 2 X1
1 2 X1
X10
MDS/FDS/
SDS
1 2 X1
Relay 1
X22 1
RB RB U+ U-
Braking
resistor2
X22 1
U+ U-
U+ U-
X22 1
U+ U-
X22 1
U+ U-
4
4
4
4
X22 1
U+ U-
X22 1
U+ U-
4 4
2
DC link fuse
DC link fuse
1
2
3
4
With size-3 MDS 5000 and SDS 5000 devices: X20, terminals ZK+, ZK-.
Dimension the braking resistor in accordance with the braking performance of the DC link coupling and
the technical data of the device.
See chapter 5.3.
Dimension the conductor cross-sections of the DC link connection according to the requirements of your
application. A reference point can be the maximum cross-section for the terminals X22 for BG0 to BG2 or
X20 for BG3.
ID 442269.06
WE KEEP THINGS MOVING
Fig. 5-2 Principal circuit diagram of the DC link coupling
67
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Combinations
The following table shows the possible combinations for the DC link connection. There are a total of 15
combinations available.
Example: Combination no. 7:
With combination no. 7, you can combine an inverter of size 1 in group 1 with two devices of size 0 in group
2. Group 3 is not set up. The line fuse must have a rated current of 20 A. The groups are separated via the
DC link fuse of type 1. Wait three minutes before switching on the devices of the DC link connection again.
Group 1
DC link fuse
Group 2
DC link fuse
Group 3
Ta)
[min]
MDS/FDS/
SDS
MDS/SDS
MDS/FDS/
SDS
MDS/FDS/
SDS
Size
Size
0
Size
1
Size
2
Size
3
Size Size
0
1
Size 0
Line fuse
10 A
20
Ab)
50
Ab)
80
Ab)
—
—
—
Max. Pinc)
4 kW
10
kW
20
kW
45
kW
—
—
—
1
max.
4
—
—
—
—
—
—
—
—
1
2
—
max.
4
—
—
—
—
—
—
—
5
3
—
3
—
—
Type 1
2
—
—
—
5
4
—
3
—
—
Type 1
1
—
—
—
3
5
—
2
—
—
Type 1
2
—
—
—
3
6
—
2
—
—
Type 1
1
—
—
—
4
7
—
1
—
—
Type 1
2
—
—
—
3
8
—
—
max.
3
—
—
—
—
—
—
2
9
—
—
3
—
Type 2
—
1
Type 1
2
2
10
—
—
3
—
Type 1
2
—
—
—
2
11
—
—
3
—
Type 2
—
1
—
—
2
12
—
—
2
—
Type 2
—
1
—
—
2
13
—
—
2
—
Type 2
—
1
Type 1
1
2
14
—
—
1
—
Type 2
1
—
—
—
2
15
—
—
—
max.
3
—
—
—
—
—
1
Device family
WE KEEP THINGS MOVING
Combination no.
68
a) Restart time
b) Note the list of line fuses for UL-compliant use in section 5.3.1 Line fuse
c) Maximum sum of drive power
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Instead of delaying the process by the restart time, you can determine the restart time by evaluating the E14
parameter. The parameter in all devices connected to the network must show that the load relay is open
before the supply voltage may be switched on again. You can query the parameter via the fieldbus or binary
output. If you are setting up a DC link connection only with devices from the SDS 5000 family or A-devices
(HW version 200 or higher), you do not need to note the restart time.
Fuses
CAUTION!
Danger of machine standstill! If a fuse element fails, the second fuse element will be damaged.
 Always replace the elements of a fuse in pairs.
Remember the following points during mounting and operation:
• Shield the DC link connections if the cables are longer than 20 cm. This prevents EMC problems.
• Use the two outer elements of the fuse holder to ensure adequate safe flashover distance.
• Use the following fuses to protect the DC link:
Type 1
SIBA Sicherungs-Bau GmbH
Borker Straße 22
D-44534 Lünen
www.siba.de
Size
10 x 38
Operating class
gRL
Rated voltage
AC 600 V
Rated current
10 A
20 A
Power loss per element
1.6 W
3.5 W
6003434.10
6003434.20
Art. no. of fuse
Art. no. of fuse holder
ID 442269.06
5106304.3
WE KEEP THINGS MOVING
Manufacturer
Type 2
69
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.11
X100-X103: Analog and binary signals
Remember that the terminals X100 and X101 are integrated in the device. Terminals X103D and X103E are
integrated on the optional LEA 5000 accessory.
WARNING!
Danger of machine malfunction due to EMC interference!
 Do not use cables longer than 30 m (leads to binary inputs, binary outputs, analog inputs and analog
outputs)!
WE KEEP THINGS MOVING
Information
Remember that the scanning time and update rate TA min depend
on the complexity of the user program on the inverter. Both times
can assume the values 1, 2, 4, 8, 16 or 32 ms depending on the
scope of the user program. Also consider the setting of parameter
A150 cycle time.
70
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description – X100
Designation Function
Data
1 2 3 4 5 6 7 8
1
AE1+
+ Input of the analog input AE1 
Resolution: 10 bits + sign
2
AE1-Shunt
Current input; shunt connection Pin Reference: Pin 3
2 must be jumpered with pin 1.
IE = ± 20 mA
Ri = 510 Ω
Scan time: TA min = 1 ms
3
AE1-
Inverted input of analog input AE1
UE max against Pin 1 = 30 V
UE max against prot. cond. = 15 V
UE max against AGND = 30 V
4
AE2+
+ Input of analog input AE2;
Resolution: 10 bits + sign
Reference: Pin 5
UE = ± 10 V
Ri = 40 kΩ
TA min = 1 ms
UE max against Pin 5 = 30 V
UE max against prot. cond. = 15 V
UE max against AGND = 30 V
5
AE2-
Inverted input of analog input AE2
UE max against prot. cond. = 15 V
UE max against AGND = 30 V
6
AA1
Analog output 1

7
AA2
Analog output 2
Reference: Pin 8
IA max = 10 mA
TA min = 1 ms
Ri = 20 Ω
Resolution:
• FDS 5000: 10 bits + sign
• FDS 5000A: 11 bits + sign
8
AGND
Reference ground for analog
signals
ID 442269.06
Reference: Pin 3
UE = ± 10 V
Ri = 40 kΩ
TA min = 1 ms
UE max against Pin 3 = 30 V
UE max against prot. cond. = 15 V
UE max against AGND = 30 V
—
WE KEEP THINGS MOVING
Pin
71
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Maximum conductor cross-section
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
Flexible with cable end, without plastic 1,5
sleeve
0,5
2 leads with the same cross-section
with double cable end
—
WE KEEP THINGS MOVING
Flexible with cable end, with plastic
sleeve
72
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description X101
Pin
9 10 11 12 13 14 15 16 17 18 19
Designation
Function
Data
9
GND 18 V
Reference ground for pin 19
—
10
DGND
Reference ground for pins 11 to
18
—
11
BE1
12
BE2
13
BE3a)
14
BE4a)
15
BE5a)
16
BA1
17
Binary input
High level: 12–30 V
Low level: 0–8 V
UE max = 30 V
TA min = 1 ms (with timestamp)
IE max = 16 mA at UE max
BA2
Binary output
IA max = 20 mA (to HW version 190)
IA max = 50 mA (from HW version 200)
TA min = 1 ms
18
24 V-In
24 V power for binary outputs
Input area: 18–28.8 V
19
18 V-Out
Auxiliary voltage 18 V
UA = 16–18 V
IA max = 50 mA
a) BE3, BE4 and BE5 can be used as encoder inputs. See chapter 5.12.2 BE encoder and BA encoder simulation.
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
Flexible with cable end, without plastic 1,5
sleeve
Flexible with cable end, with plastic
sleeve
0,5
2 leads with the same cross-section
with double cable end
—
Information
When the 24 V power fails, binary inputs BE6 to BE13 have signal
status 0 (regardless of the physical signal state).
ID 442269.06
WE KEEP THINGS MOVING
Maximum conductor cross-section
73
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description X103E – LEA 5000
Pin
Designation
9 10 11 12 13 14 15 16
9
BE6
10
BE7
11
BE8
12
BE9
13
BE10
14
BE11
15
BE12
16
BE13
Function
Data
Binary input
Reference: Pin – (GND) of terminal
X103D
High level: 12–30 V
Low level: 0–8 V
UE max = 30 V
TA min = 1 ms
IE max = 3 mA with UE max
Maximum conductor cross-section
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
0,5
2 leads with the same cross-section
with double cable end
—
Terminal description X103D – LEA 5000
Pin
Designation
1 2 3 4 5 6 7 8
74
Flexible with cable end, with plastic
sleeve
+ -
WE KEEP THINGS MOVING
Flexible with cable end, without plastic 1,5
sleeve
+
+ 24 V
-
GND
1
BA3
2
BA4
3
BA5
4
BA6
5
BA7
6
BA8
7
BA9
8
BA10
Function
Data
Voltage supply
UE max = 20,4–28,8 V 
IE max = 1,5 A
Binary output
IA max = 50 mA
TA min = 1 ms
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Maximum conductor cross-section
Connection type
Maximum conductor cross-section
[mm2]
Rigid
1,5
Flexible
1,5
Flexible with cable end, without plastic 1,5
sleeve
Flexible with cable end, with plastic
sleeve
0,5
2 leads with the same cross-section
with double cable end
—
Connection examples
Potentiometer
Inverter
Inverter
X100
1 AE1+
2 AE1-Shunt
3 AE1-
X100
1 AE1+
2 AE1-Shunt
3 AE1-
6
7
8
AA1
AA2 (+ 10 V)
AGND
Voltage (max. ± 10 V)
0-5V
0 - 10 V
max. ± 10 V
6
7
8
AA1
AA2
AGND
Analog output voltage
Inverter
Inverter
X100
1 AE1+
2 AE1-Shunt
3 AE1-
X100
1 AE1+
2 AE1-Shunt
3 AE1-
6
7
8
ID 442269.06
0 (4) 20 mA
AA1
AA2
AGND
V
6
7
8
AA1
AA2
AGND
WE KEEP THINGS MOVING
R10K
Current (0 - 20 mA, 4 - 20 mA)
75
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.12
Encoder
Information
Remember that the encoder interfaces can usually evaluate or
simulate several systems (e.g., HTL and TTL incremental encoder).
In the parameters enter the particular system that you are
connecting to an interface. Please consult the inverter operating
manual in this case.
5.12.1
X4
NOTICE
Danger of encoder destruction!
 X4 may not be connected or disconnected when the device is on!
General specification
UA
15-16 V
IA max
300 mA
Maximum cable length
100 m
WE KEEP THINGS MOVING
Specification for incremental signals
76
Encoder type
Only TTL and HTL encoders with N channel may be connected to X4.
Encoders without N channel generate a fault when the device starts.
Limit frequency
≤ 1 MHz
Calculation example for TTL encoder with 2,048 pulses per revolution: 
50 revolutions/s (corresponds to 3,000 rpm) * 2,048 pulses/revolution 
= 102,400 pulses/s 
= 102.4 kHz << 1 MHz
Signal level
TTL and HTL
Encoder supply
UA
Through
Remarks
15-16 V
Encoder sense line connected
—
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description X4 for HTL encoder
Pin
Socket
1
9

8
15
Designation
Function, Data
1
B+
Differential input for B-track
2
GND
Reference for encoder power on pin 4
3
N+
Differential input for N-track
4
UA
Encoder power
5
—
—
6
A+
Differential input for A-track
7
—
—
8
—
—
9
B-
Inverse, differential input for B-track
10
N-
Inverse, differential input for N-track
11
A-
Inverse, differential input for A-track
12
Sense
Sensor lead for power supply to settle the
encoder power
13
—
—
14
—
—
15
—
—
Pin
Socket
1
9

8
15
Designation
Function, data
1
—
—
2
GND
Reference for encoder supply to pin 4
3
—
—
4
UA
Encoder supply
5
B+
Differential input for B channel
6
—
—
7
N+
Differential input for N channel
8
A+
Differential input for A channel
9
—
—
10
—
—
11
—
—
12
Sense
Sensor line for the supply voltage to adjust
the encoder supply
13
B-
Inverse, differential input for B channel
14
N-
Inverse, differential input for N channel
15
A-
Inverse, differential input for A channel
ID 442269.06
WE KEEP THINGS MOVING
Terminal description X4 for TTL encoder
77
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.12.2
BE encoder and BA encoder simulation
To evaluate single-ended incremental encoder or stepper motor signals, use binary inputs BE3, BE4 and BE5.
If you would like to simulate them, use outputs BA1 and BA2.
If you have connected an encoder, you cannot read or simulate any other binary signals on the binary
interfaces listed above.
General specifications
Maximum cable length
30 m
Signal level
HTL
Evaluation – incremental and stepper motor signals
High level
12–30 V
Low level
0–8 V
UE max
30 V
IE max
16 mA
fmax
100 kHz
TA min
In the cycle time of the application with time stamp correction (resolution 
1 µs)
WE KEEP THINGS MOVING
Simulation – incremental and stepper motor signals
78
IA max
HW version 190 or lower: 20 mA
HW version 200 or higher: 50 mA
Eff. update speed
1 kHz
Maximum output frequency for 250 kHz
one track
Extrapolation frequency
1 MHz
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
Terminal description X101 incremental encoder and stepper motor signals
9 10 11 12 13 14 15 16 17 18 19
Designation
Function
Data
9
GND 18 V
Reference ground for pin 19
—
10
DGND
Reference ground for pins 11 to 18
—
11
BE1
—
—
12
BE2
—
13
BE3
Evaluation:
Incremental encoder: N
Stepper motor signals: –
14
BE4
Evaluation:
Incremental encoder: A
Stepper motor signals: freq.
15
BE5
Evaluation:
Incremental encoder: B
Stepper motor signals: direction
16
BA1
Simulation
Incremental encoder: A
Stepper motor signals: freq.
17
BA2
Simulation
Incremental encoder: B
Stepper motor signals: direction
18
24 V-In
24 V power
Input range: 18–28.8 V
19
18 V-Out
Auxiliary voltage 18 V
UA = 16–18 V
IA max = 50 mA
ID 442269.06
—
WE KEEP THINGS MOVING
Pin
79
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.13
Fieldbus
5.13.1
X200: CANopen
Prerequisite for the CANopen link:
• CAN 5000
Information
Please see the supplementary documentation of CANopen (see
section 1.2 Other manuals)!
Terminal description X200
Pin
Plug
5
6
Function
1
nc
—
2
CAN-low
CAN-low line
3
GND
Signal Ground
4
nc
—
5
nc
—
6
CAN-low
CAN-low line connected internally with pin 2
7
CAN-high
CAN-high line
8
nc
—
9
CAN-high
CAN-high line connected internally with pin 7
WE KEEP THINGS MOVING
1
9
Designation
80
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.13.2
X200: PROFIBUS
Prerequisite for the PROFIBUS link:
• DP 5000
Information
Please see the supplementary documentation of PROFIBUS DP
(see section 1.2 Other manuals)!
Terminal description X200
Pin
Function
1
nc
—
2
nc
—
3
B
RxD / TxD-P (send/receive data +)
4
RTS
Direction control for repeater +
5
GND
Ground to + 5 V
6
+5 V
Power for terminating resistors
7
nc
—
8
A
RxD / TxD-N (send/receive data -)
9
nc
—
WE KEEP THINGS MOVING
socket
Designation
ID 442269.06
81
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.13.3
X200, X201: EtherCAT
Prerequisite for the EtherCAT link:
• ECS 5000
Information
Please see the supplementary documentation of EtherCAT (see
section 1.2 Other manuals)!
Terminal description X200 und X201
Pin
Designation
Function
1
TxData+
EtherCAT communication
2
TxData-
3
RecvData+
4
unused
5
unused
6
RecvData-
EtherCAT communication
7
unused
—
8
unused
—
WE KEEP THINGS MOVING
Specifications of the cable
STOBER offers fabricated cables for the EtherCAT connection. Correct function is not guaranteed unless
these cables are used. Read and comply with chapter 7 Accessories.
Another possibility is to use cables with the following specifications:
82
Plug con. wiring
Patch or Crossover
Quality
CAT5e
Shield
SFTP or PIMF
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.13.4
X200, X201: PROFINET
Requirement for the die PROFINET connection:
• PN 5000
Information
Observe the PROFINET operating manual (see section 1.2 Other
manuals)!
X200 and X201 terminal description
The terminal configuration is determined by T 568-B.
Pin
Designation
Function
1
TxData +
PROFINET communication
2
TxData -
3
RecvData +
4
nc
5
nc
6
RecvData -
PROFINET communication
7
nc
Connect via RC-link with housing
8
nc
Connect via RC-link with housing
WE KEEP THINGS MOVING
Observe the PROFINET installation guideline for the cable specification (PROFINET Order No. 8.071,
identification: TC2-08-0001); you can obtain the document at www. profibus.com.
ID 442269.06
83
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.14
X3: PC, USS
Connection to the PC or USS can be implemented with serial interface X3 on the front of the inverter. Setting
up the PC connection is described in the inverter operating manual.
Terminal description X3
Pin
Plug
5
9
1
6
Designation
Function
Data
1
+10 V
Power for Controlbox
IA max = 30 mA
2
Rx
Communication: Receiving input
—
3
nc
Used internally. Do not activate!
—
4
Tx
Communication: Sending output
—
5
SG
Reference potential for pins 2 and 4
—
6
nc
Used internally. Do not activate!
—
7
nc
8
nc
9
nc
Specifications of the cables
STOBER offers fabricated cables for the connection to the PC.Correct function is not guaranteed unless these
cables are used. Read and comply with chapter 7 Accessories.
WE KEEP THINGS MOVING
PC
84
2
Inverter
2
3
3
4
5
FDS cable G3
ID. No. 41488
4
5
Housing
ID 442269.06
5
Connection
Projecting manual POSIDRIVE® FDS 5000
5.15
Cables
Information
To ensure proper functionality of the drive we recommend using
cables from STOBER that are coordinated with the system. In case
of use of unsuitable connection cables, we reserve the right to reject
claims under the warranty.
5.15.1
Encoder Cables
Encoder HTL
HTL incremental encoders can be combined with STOBER motors of series ED/EK or EZ.
The suitable encoder cable is described below.
Encoder cable – plug connector con.23
Motor
Wire colors
Signal
Angle flange socket
Pin
Sub-D
connector at
terminal X4
Motorinternal
Encoder
Pin
B-
PK
YE
9
3
N+
RD
PK
3
4
N-
BK
GY
10
5
A+
BN
BN
6
6
A-
GN
WH
11
B+
GY
GN
1
GND
WH
BU
2
12
U2
BN
RD
4
Housing
Shield
1
7
8
9
10
11
Cable color – key
BK
BLACK
PK
PINK
BN
BROWN
RD
RED
BU
BLUE
VT
VIOLET
GN
GREEN
WH
WHITE
GY
GREY
YE
YELLOW
OG
ORANGE
ID 442269.06
WE KEEP THINGS MOVING
2
85
6
Examples of connections
Projecting manual POSIDRIVE® FDS 5000
Examples of connections
A3
F2
F11
A1
L1 L2 L3 PE
L+ M
X10
X11
no fault
enable
binary input
binary output
1
2
3
4
M
L+
X1
L+
M
L+
M
L1
L2
L3
PE
6
STÖBER ANTRIEBSTECHNIK
X2
1
2 3
8
7
4
PTC
RB RB
PTC
X21
X4
X20
U V W PE
F3
A2
1
2
3
PE
R1
6
+
5
X302
-
X300
X301
BRM 5000
WE KEEP THINGS MOVING
U V W PE
86
M1
Y1
M
3
1
direct
brake control
1 2
6
5
-
+
3
7
4
8
n
circuit protection
tripping characteristics C
ID 442269.06
6
Examples of connections
L+ M
X10
X11
binary output
1
2
3
4
M
L+
X1
2
3
PE
2 3
4
PTC
X2
1
PTC
RB RB
A4
~
PowerBox
1
F3
X21
X4
X20
F4
K1
STÖBER ANTRIEBSTECHNIK
U V W PE
N
binary input
L
enable
M
L1 L2 L3 PE
no fault
L+
F2
F11
A1
A3
L+
M
L1
L2
L3
PE
Projecting manual POSIDRIVE® FDS 5000
R1
7
~
-
+
8
U V W PE
K1
M
3
n
indirect
brake control
1
circuit protection
tripping characteristics C
ID 442269.06
Y1
-
+
WE KEEP THINGS MOVING
M1
87
7
Accessories
Projecting manual POSIDRIVE® FDS 5000
7
Accessories
Terminal module LEA 5000
ID no. 49029
Terminals:
• 8 binary inputs
• 8 binary outputs
Brake module for 24 V brake BRM 5000
ID no. 44571
Description: Control of up a motor halting brake.
WE KEEP THINGS MOVING
EMC shroud EM 5000
ID no. 44959
88
Description: Accessory part for securing the shield of the motor lead.
Can be added to the basic housing.
Including shield connection terminal.
ID 442269.06
7
Accessories
Projecting manual POSIDRIVE® FDS 5000
Inverter
HW status of the inverter CAN 5000
DP 5000
ECS 5000
PN 5000
FDS 5000A
200 or higher
Yes
Yes
Yes
Yes
FDS 5000
up to 199
Yes
Yes
Yes
No
Fieldbus module CANopen DS-301 CAN 5000
ID no. 44574
Description: 
Accessory part for coupling of CAN-Bus.
Fieldbus module PROFIBUS DP-V1 DP 5000
ID no. 44575
Description: 
Accessory part for coupling of PROFIBUS DP-V1.
Description: 
Accessory part for coupling of EtherCAT (CANopen via EtherCAT).
EtherCAT cable
Description: 
EtherNet patch cable, CAT5e, yellow.
ID no. 49313: approx. 0.2 m
ID no. 49314: approx. 0.35 m
ID 442269.06
WE KEEP THINGS MOVING
Fieldbus module EtherCAT ECS 5000
ID no. 49014
89
7
Accessories
Projecting manual POSIDRIVE® FDS 5000
Fieldbus module PROFINET
ID no. 53893
Description: 
Accessory part for coupling of PROFINET.
ASP 5001 – safe torque off
The ASP 5001 may only be installed by STOBER.
The ASP 5001 must be ordered together with the basic device.
Connection cable G3
ID no. 41488
WE KEEP THINGS MOVING
Description: 
Connection of inverter to terminal X3 and the PC, approx. 5 m, 
sub D plug, 9-pin, socket/socket.
90
USB adapter on RS232
ID no. 45616
Controlbox
Description:
Operating unit for parameterisation and operation of the inverters. 
The connecting lead (1.5 m) is included in the scope of supply.
ID no. 42224: Service type
ID no. 42225: Built-in DIN housing 96x96 mm, Protection rating IP 54
ID 442269.06
7
Accessories
Projecting manual POSIDRIVE® FDS 5000
Controlbox cable
Description:
Connection cable from Controlbox to inverter.
ID no. 43216: 5 m
ID no. 43217: 10 m
Paramodule
Description:
Memory module for configuration and parameters.
For FDS 5000 (HW version < 190), 128 kbyte: ID no. 49319
For FDS 5000A (HW version > 200), 1 Mbyte: ID no. 55463
WE KEEP THINGS MOVING
•
•
ID 442269.06
91
WE KEEP THINGS MOVING
Notes
ID 442269.06
Global presence
Address registers
Always up to date on the internet: www.stober.com → contact
• Technical Offices (TB) for advice and marketing in Germany
• Global presence for advice and marketing in about 25 countries
• Service Network Germany
• Service Network International
• STOBER Subsidiaries:
STÖBER ANTRIEBSTECHNIK GmbH
Hauptstraße 41a
4663 Laakirchen
Fon +43 7613 7600-0
Fax +43 7613 7600-2525
E-Mail: office@stoeber.at
www.stoeber.at
Switzerland
STÖBER SCHWEIZ AG
Rugghölzli 2
5453 Remetschwil
Fon +41 56 496 96 50
Fax +41 56 496 96 55
eMail: info@stoeber.ch
www.stoeber.ch
China
STOBER CHINA
German Centre Beijing
Unit 2010, Landmark Tower 2,
8 North Dongsanhuan Road
Chaoyang District
100004 Beijing
Fon +86 10 65907391
Fax +86 10 65907393
eMail: info@stoeber.cn
www.stoeber.cn
USA
STOBER DRIVES INC.
1781 Downing Drive
Maysville, KY 41056
Fon +1 606 7595090
Fax +1 606 7595045
eMail: sales@stober.com
www.stober.com
Great Britain
STOBER DRIVES LTD.
Upper Keys Business Village
Keys Park Road, Hednesford
Cannock WS12 2HA
Fon +44 1543 458 858
Fax +44 1543 448 688
E-Mail: mail@stober.co.uk
www.stober.co.uk
Japan
STOBER Japan
P.O. Box 113-002, 6 chome
15-8, Hon-komagome
Bunkyo-ku
Tokyo
Fon +81 3 5395-6788
Fax +81 3 5395-6799
eMail: mail@stober.co.jp
www.stober.co.jp
France
STÖBER S.a.r.l.
131, Chemin du Bac à Traille
Les Portes du Rhône
69300 Caluire et Cuire
Fon +33 4 78989180
Fax +33 4 78985901
eMail: mail@stober.fr
www.stober.fr
Italy
STÖBER TRASMISSIONI S. r. l.
Via Italo Calvino, 7
Palazzina D
20017 Rho (MI)
Fon +39 02 93909-570
Fax +39 02 93909-325
eMail: info@stoeber.it
www.stoeber.it
Singapore
STOBER Singapore Pte. Ltd.
50 Tagore Lane
#05-06B
Entrepreneur Centre
Singapore 787494
Fon +65 65112912
Fax +65 65112969
E-Mail: info@stober.sg
www.stober.sg
www.stober.com
Austria
STÖBER ANTRIEBSTECHNIK GmbH + Co. KG
Kieselbronner Str. 12
75177 PFORZHEIM
GERMANY
Tel. +49 7231 582-0
Fax. +49 7231 582-1000
E-Mail: mail@stoeber.de
24/h service hotline +49 180 5 786 323
www.stober.com
Technische Änderungen vorbehalten
Errors and changes excepted
ID 442269.06
07/2014
442269.06

Similar documents

×

Report this document