SIGN COMPONENTS MANUAL (SAM)

Document technical information

Format pdf
Size 1.3 MB
First found Jun 9, 2017

Document content analysis

Language
English
Type
not defined
Concepts
no text concepts found

Persons

Organizations

Places

Transcript

SIGN COMPONENTS MANUAL
(SAM)
For use by manufacturers covered under UL’s Listing and Follow-Up Services for Electric Signs
(UXYT/7) and Field-Assembled Skeletal Neon Sign and Outline Lighting Systems (UZBL/7), and for
use by UL Representatives performing UL Follow-Up Service inspection.
This Manual authorizes manufacturers to use certain UL Recognized Components, Classified
Components and other non-Listed products*, when they are used under 1) the conditions
expressed for the components in this Manual, 2) the installation instructions for the component,
and 3) the requirements expressed in the Follow-Up Service Procedure, the associated Follow-Up
and Inspection Instructions (FUII Pages) and the UL Standard for Electric Signs (UL 48).
* Not covered by this manual, are non-Listed component materials that do not require additional
authorization because requirements regarding their suitability and conditions of use are found in
the UL Standard for Electric Signs (UL 48). Some examples are sheet metal, glass and
thermoplastic diffusers (except those used to enclosure wiring and current-carrying parts).
UL continuously updates this manual and makes the current version available. Updated versions
of this manual are distributed periodically to all subscribers to UL's Listing Service and Follow-Up
Services for Electric Signs (UXYT/7), Field-Assembled Skeletal Neon Sign and Outline Lighting
Systems (UZBL/7), and subscribers to UL's Recognition Service and Follow-Up Services for Sign
Accessories (UYMR2).
January 23, 2014 Edition
Copyright  2014 UL LLC
ii
IMPORTANT INFORMATION FOR USERS OF THIS MANUAL
January 23, 2014
Introduction
This document is issued by UL LLC and is intended only to be used in conjunction with the Follow-Up
Service Procedure and the UL Standard for Electric Signs, UL 48, by Manufacturers covered under UL’s
Follow-Up Services and by UL Representatives conducting UL Follow-Up Service Inspections.
This Manual contains the names of companies authorized to use the Recognized Marking on or in
connection with components which have been evaluated by UL and found to be in compliance with UL’s
requirements. These companies, as well as the manufacturers and submitters of the products, have
entered into an Agreement with UL to use the Recognized Marking only on or in connection with products
manufactured in compliance with UL’s requirements. It should be noted that Recognized products of
different makes or model designations are not necessarily equivalent in quality or performance.
Where products are identified as being Recognized or Classified, the appearance of catalog or model
numbers or other specific product designations in this Manual signifies, among other things, that: 1)
representative samples of these products have been submitted to UL and found to comply with the
applicable requirements, and that 2) the manufacturer has been authorized to use the Recognized
Marking on production that continues to comply with UL’s requirements and is subject to UL’s Follow-Up
Service. Manufacturers are not obligated to use the Recognized Marking on all of their production, and
products which do not bear the Recognized Marking are not required by UL to comply with UL’s
requirements. Accordingly, the appearance of a company’s name or a specific product designation in this
Manual does not in itself assure that the products so specified or identified are subject to UL’s Follow-Up
Service. The manufacturer’s products are not subject to UL’s Follow-Up Service unless they bear the
Recognized Marking. Only those products bearing the Recognized and Classification Marking should be
considered as covered by UL’s Recognition, Classification and Follow-Up Service.
This Manual contains Component Recognitions in effect as of January 23, 2014. Records of Component
Recognitions and Classifications issued or withdrawn after this date will be found in UL’s Listing
Information database or historical records. In addition, Component Recognition’s and Classifications
issued after this date will appear in future revisions of this Manual.
Use of the Sign Components Manual
UL’s Follow-Up Service Procedure authorizes manufacturers covered under UL’s Listing and Follow-Up
Services for Electric Signs (UXYT/7), and Field-Assembled Skeletal Neon Sign and Outline Lighting
Systems (UZBL/7) to apply the specified UL Listing Mark to products which comply with the requirements
expressed in the Follow-Up Service Procedure, the associated Follow-Up and Inspection Instructions
(FUII Pages) and the UL Standard for Electric Signs (UL 48). Compliance with these documents requires
that manufacturers primarily use component products that are UL Listed. This Manual authorizes
manufacturers to use certain UL Recognized Components, Classified Components and other non-Listed
products, when they are used under 1) the conditions expressed for the components in this Manual, 2)
the installation instructions for the component, and 3) the requirements expressed in the documents
noted above.
This Manual is intended to assist manufacturers who may wish to use a Recognized Component or other
non-Listed products in their UL Listed Electric Signs, Field Assembled Skeletal Neon Sign and Outline
Lighting Systems. For all components, consult the Product Category Guide (General) Information
preceding the individual component listings as well as the individual listings themselves for use conditions
and ratings, as well as the required Recognized Marking.
This Manual provides the following:

authorization to use all components listed when the component is used according to the
requirements of the Follow-Up Service Procedure, the UL Standard for Electric Signs, UL 48, the
associated Follow-Up and Inspection Instructions (FUII Pages), and the specified limitations or
conditions of use;
January 23, 2014
IMPORTANT INFORMATION FOR USERS OF THIS MANUAL

names of companies which are authorized to provide components bearing a Recognized Marking
as of the date noted in the introduction on page i;

information about the form and nature of the Recognized Marking to be used by a specific
manufacturer or for a specific class or category of product;

information relating to limitations or conditions of use applying to the component;
Component Recognitions are arranged alphabetically in this Manual by product category and, when
included, individual Recognitions are arranged alphabetically by company name under each category.
Products which are neither Listed nor Recognized by UL are grouped under the category titled
“Miscellaneous” and identified by the initials MISC, and are arranged alphabetically by their common
name.
When individual Recognitions are not listed following the category title, refer to the UL’s Recognized
Component Directory for names of companies authorized to use the Recognized Marking and for
components that are authorized to bear the Recognized Marking. The products are to be marked by
Company name or UL File Number and catalog designation and, when Recognized for use in Canada,
.
Recognized Component Mark for Canada,
When included, Product Category Guide (General) Information at the beginning of each product category,
except MISC, provides important information regarding the scope and limitation of the Component
Recognitions and a general description of the Recognized Marking authorized for Component
Recognition in that category. Unless otherwise noted, the limitations and conditions of use provided in
the Product Category Guide (General) Information are to be applied to all components having
Recognition in that category.
Some companies may be authorized to use a trade name or trademark for identification of Recognized
Components in place of their company name, in such cases, refer to UL’s Recognized Component
Directory for a reproduction of the trade name or trademark.
Products listed under the category identified by the initials MISC may be produced by any manufacturer.
Such products are neither UL Listed nor Recognized by UL, and, UL in no way has established
Agreements with the manufacturers of such products that may be used as a basis to insure their
uniformity or performance.
All components must be used for only the purpose intended by their manufacturer and as may be
identified in this Manual, and under the conditions of use identified in this Manual. However, even when
the conditions of use and all other applicable requirements are met, UL reserves the right to evaluate
specific constructions incorporating these products and determine suitability.
iii
1
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
FLEXIBLE METAL CONDUIT
(DXUZ2)
Shall be used within a metal sign body and polymeric sign face.
Not to be relied upon for grounding or bonding.
GASKETS AND SEALS (JMLU2)
& GASKET MATERIALS (JMST2)
1. Suitable for use in an outdoor sign as a weather seal, such as for a door or removable cover of a sign body or enclosure.
2. Adhesive alone is not suitable to secure a gasket unless the adhesive has been separately authorized for that application.
3. A gasket material designated to be used in a UL 1598, UL 508, UL 50 application is considered to be suitable for use in an
outdoor sign.
MISCELLANEOUS NON-RECOGNIZED DEVICES
(MISC)
"Christmas Tree" Fasteners
1. Only suitable for use in indoor signs.
2. Only suitable to secure lightweight decorative parts or neon tube supports.
Velcro
1. Only suitable for use in indoor signs.
2. Not suitable for completing an electrical enclosure.
3. Adhesive alone is not suitable to secure Velcro to non-flat surfaces when Velcro is used to secure parts weighing more than 4
lbs.
INSULATING BUSHINGS (NZMT2)
1. Suitable for use as mechanical protection of insulation on low-voltage wiring.
2. Suitable for use as low-voltage wiring strain relief. The strain relief test shall be conducted as described in UL48 Section 34 for
each new unit design. The manufacturer shall keep a record of each test. The Field Representative shall witness the test.
NEON TRANSFORMERS &
NEON POWER SUPPLIES (PWIK2, PWIK8)
This category covers neon transformers and power supplies for use with end products employing gas-filled glass tubing identified
as neon or electric discharge tubing.
CONDITIONS OF ACCEPTABILITY
Each Recognized Component has Conditions of Acceptability that define the parameters of use for the component in an end-use
product. Conditions of Acceptability are identified in the individual Recognitions by one or more letters appearing next to the model
designation or catalog number under the heading "Conditions of Acceptability." The letters that appear identify which of the
Conditions of Acceptability apply to the particular model or catalog number. Where the Conditions of Acceptability require testing
or are unique to the component, the letters "TR" appear next to the model designation or catalog number under the heading
"Conditions of Acceptability" and reference will need to be made to the individual Recognition Report.
 A - Intended for use only in applications that comply with the requirements of the end product.
 B - Suitable for use only indoors.
 C - Suitable for use outdoors where protected from rain, snow and water spray.
 D - Suitable for use only where the neon tubing between the neon supply electrode receptacles is either; a) one continuous
length of tubing or b) multiple lengths of tubing interconnected only with Listed more than 1000 V lampholders (see OJOV) of
the lamp-to-lamp type. Listed or Recognized Component Sign Accessories (UYMR/2) and Listed Gas Tube Sign and Ignition
Cable (GTO Cable) (ZJQX) are not acceptable for interconnecting neon tubing lengths in any part of the secondary circuit.
 E - Suitable for use only where contained in an end-use product compartment that is suitable as an electrical enclosure.
 F - Suitable for use only where made inaccessible to contact by users during user maintenance while energized.
 G - Provided with connection means suitable for factory wiring only; not for field wiring.
 H - Not provided with a means of connection in accordance with NFPA 70, "National Electrical Code," therefore, suitable
means needs to be provided in the end-use product.
 TR - Requires testing or other evaluation in the end product; refer to individual Recognition Report.
PRODUCT MARKINGS
Transformers and power supplies covered under this category are marked "Indoors," "Outdoors," "Weatherproof" or "WP."
Products marked "Indoors" are only suitable for use indoors, and products marked "Outdoors" are suitable for use indoors or
outdoors sheltered from rain, snow and the like by being located within a sign body, enclosure and the like. Products marked
"Weatherproof" or "WP" do not need to be additionally sheltered from rain, snow and the like.
January 23, 2014
2
SIGN COMPONENTS MANUAL (SAM)
Transformers and power supplies covered under this category are marked with a Type number from 1 to 8 in association with the
location designation "Indoors," "Outdoors," "Weatherproof" or "WP." These Type numbers identify particular construction features
associated with a particular transformer or power supply as identified below:
 Type 1 - Open core-and-coil neon transformer or unenclosed neon power supply with body of the unit and input and output
terminals or leads that should be enclosed in accordance with end-product requirements.
 Type 2 - Neon supply with input and output terminals or leads that should be enclosed in accordance with end-product
requirements.
 Type 3 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system, and
with output terminals or leads that should be enclosed in accordance with end-product requirements.
 Type 4 - Neon supply with input and output terminals or leads enclosed and intended for connection to a permanent wiring
system.
 Type 5 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system and
provided with integral receptacles for output connection.
 Type 6 - Cord-connected neon supply provided with integral receptacles for output connection.
 Type 7 - Cord-connected neon supply with output terminals or leads that should be enclosed in accordance with end-product
requirements.
 Type 8 - Cord-connected neon supply with enclosed output terminals or leads.
ALLANSON INTERNATIONAL INC
33 CRANFIELD RD
TORONTO, ONTARIO
CANADA M4B 3H2
E39591
Neon Power Supply, Indoor Type 7, Cat. No. SS935B-18.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 960EK120, 960EK277, 960EK347, P960EK120, P960EK277, P960EK347, 960EKF120, 960EKF277, 960EKF347,
P960EKF120, P960EKF277, P960EKF347, 7560EK277, 7560EK347, P7560EK120, P7560EK277, P7560EK347, 7560EKF277,
P7560EKF120, P7560EKF277, P7560EKF347, 660EK120, 660EK277, 660EK347, P660EK120, P660EK277, P660EK347,
660EKF120, 660EKF277, 660EKF347, P660EKF120, P660EKF277, P660EKF347, 560EK120, 560EK347, P560EK120,
P560EK277, P560EK347, 560EKF120, 560EKF347, P560EKF120, P560EKF277, P560EKF347, 460EK120, 460EK277,
460EK347, P460EK120, P460EK277, P460EK347, 460EKF120, 460EKF277, 460EKF347, P460EKF120, P460EKF277,
P460EKF347, 360EK120, 360EK277, 360EK347, P360EK120, P360EK277, P360EK347, 360EKF120, 360EKF277, 360EKF347,
P360EKF120, P360EKF277, P360EKF347.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. Mini 330EK, Mini 430EK, Mini 530EK.
Power Supplies, Indoor Type 7
Applicable Conditions of Use - A, C, G.
Cat. No. SS935B-18,Cat. No. 630FNI.
Transformers, Outdoor Type 2
Applicable Conditions of Use – A, B.
Cat. Nos. 330CI120, P330CI120, 330CI277, P330CI277, 330CI347, P330CI347, 430CI120, P430CI120, 430CI277, P430CI277,
430CI347, P430CI347, 530CI120, P530CI120, 530CI277, P530CI277, 530CI347, P530CI347, 630CI120, P630CI120, 630CI277,
P630CI277, 630CI347, P630CI347.
Transformers, Outdoor Type 4
Applicable Conditions of Use – A, B.
Cat. Nos. 330FI120, P330FI120, 330FI277, P330FI277, 330FI347, P330FI347, 430FI120, P430FI120, 430FI277, P430FI277,
430FI347, P430FI347, 530FI120, P530FI120, 530FI277, P530FI277, 530FI347, P530FI347, 630FI120, P630FI120, 630FI277,
P630FI277, 630FI347, P630FI347.
1. The secondary circuits of these transformers are not to be interconnected in series or parallel.
2. The secondary circuits of these transformers are not to be connected to ground.
*May or may not be provided with a suffix “T”.
EVERBRITE LLC
4949 S 110th
PO BOX 20020
GREENFIELD, WI 53220
E122656
Transformers, Outdoor Type 7.
Applicable Conditions of Use - A, C, G - Series 2612, Model 800-0128; Indoor Type 2, Series "NuAUX", Models 800-0174, 8000175, 800-0176, 800-0177; Series 3612, Models 800-0232, 800-0233
1. The "Animotion" system consists of the following components: Series 2612, Model 800-0128 or Series 3612, Models 800-0232
or 800-0233, Series "NuAUX," Models 800-0174, 800-0175, 800-0176, and 800-0177, and Animotion Controller Model 8000066, 800-0067, or 800-0068.
2. Series "NuAUX," Models 800-0174, 800-0175, 800-0176, and 800-0177 are only for use with Series 2612, Model 800-0128 or
Series 3612, Models 800-0232 and 800-0233.
3. Each Class 2 output on Series 2612 Model 800-0128 and Series 3612, Models 800-0232 and 800-0233 shall not exceed 2.4 A.
4. A maximum of two “NuAux” transformers may be connected directly to each Model 800-0128, Model 800-0232 or Model 8000233 Class 2 output.
FRANCE A SCOTT FETZER CO
E10092
3
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
726 FAIRVIEW BLVD W
PO BOX 300
FAIRVIEW, TN 37062
Power Supplies, Indoor Type 7
Applicable Conditions of Use - A, C, G.
Cat. Nos. 6000-FE1G-2, 6000-FE1G-D2, 6000-FS1G-2, -FS1G-D2, 9000-FE1G-2, 9000-FS1G-2, 9000-FE1G-D2, 9000-FS1GD2, 12000FE1G-D2, 12000FS1G-D2.
1. Power supply cord is a minimum of 18 in. in length. Suitability of length of power supply cord to be evaluated in end use product.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 3030 PBKMG 734, 3030 PBKMG 751, 4030 PBKMG 734, 4030 PBKMG 751, 5030 PBKMG 734, 5030 PBKMG 751.
Transformers, Outdoor Type 5
Applicable Conditions of Use - A, C, D.
Cat. Nos. 3030 PBKMAG 51, 4030 PBKMAG 51, 4060 PBKMAG 51, 4060 PBKMAG 51 277, 5030 PBKMAG 51, 5030 PBKMAG
51 277, 5060 PBKMAG 51, 5060 PBKMAG 51 277, 6030 PBKMAG 51, 6030 PBKMAG 51 277, 6060 PBKMAG 51, 6060 PBKMAG
51 277, 7530 PBKMAG 51, 7530 PBKMAG 51 277, 7560 PBKMAG 51, 7560 PBKMAG 51 277, 9030 PBKMAG 51, 9030 PBKMAG
51 277, 9060 PBKMAG 51, 9060 PBKMAG 51 277.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 3030 PBKMG 51, 3060 PBKMG 51, 4030 PBKMG 51, 4030 PBKMG 51 277, 4060 PBKMG 51, 4060 PBKMG 51 277,
5030 PBKMG 51, 5030 PBKMG 51 277, 5060 PBKMG 51, 5060 PBKMG 51 277, 6030 PBKMG 51, 6030 PBKMG 51 277, 6060
PBKMG 51, 6060 PBKMG 51 277, 7530 PBKMG 51, 7530 PBKMG 51 277, 7560 PBKMG 51, 7560 PBKMG 51 277, 9030 PBKMG
51, 9030 PBKMG 51 277, 9060 PBKMG 51, 9060 PBKMG 51 277, 12030 PBKMG 51, 12030 PBKMG 51 277, 15030 PBKMG 51,
15030 PBKMG 51 277.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 4030 PBKMCG 51, 4060 PBKMCG 51, 5030 PBKMCG 51, 5060 PBKMCG 51, 6030 PBKMCG 51, 6060 PBKMCG 51,
7530 PBKMCG 51, 7560 PBKMCG 51, 9030 PBKMCG 51, 9060 PBKMCG 51.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 4030PBKMG34, 4060PBKMG34, 5030PBKMG34, 5060PBKMG34, 6030PBKMG34, 6060PBKMG34, 7530PBKMG34,
7560PBKMG34, 9030PBKMG34, 9060PBKMG34.
Transformers, Outdoor Type 5
Applicable Conditions of Use - C, D, E.
Cat. Nos. 4030PBKMCG34, 4060PBKMCG34, 5030PBKMCG34, 5060PBKMCG34, 6030PBKMCG24, 6060PBKMCG34,
7530PBKMCG24, 7560PBKMCG34, 9030PBKMCG34.
Transformers, Indoor Type 1
Applicable Conditions of Use - A, B, E, F, H.
Cat. Nos. 6025 SEG-U and 3020 SEG-U.
1. The need to perform a Strain Relief test shall be determined in the end product.
HEICO LIGHTING, DIV OF EMD TECHNOLOGIES CO
400 RUE DU PARC
ST EUSTACHE, QC J7R 0A1 CANADA
E145519
Power Supply, Indoor, Type 7
Applicable Conditions of Use - A, C, G.
Models Platinum-5000-20-SPT.
Tradename "HEICO lighting" or trademark
VENTEX TECHNOLOGY INC
SUITE 350
1440 WEST INDIANTOWN RD
JUPITER, FL 33458
E187585
Neon Power Supply, Indoor Type 7
Applicable Conditions of Use - A, C, G - Model VT9030-120C, VT9030D-120C, VT9030F-120C, "Y" Cord - Model WA0022,
Accessory for use with Models VT9030-120C, VT9030D-120C, VT9030F-120C.
COMPONENT SIGNS (UXYT2)
COOPER WHEELOCK INC
273 BRANCHPORT AVE
LONG BRANCH, NJ 07740
E318141
LED message readout display sign, Cat. Nos. Series LEMD.
1. This product is only suitable for connection to a UL Listed or Recognized Class 2, 24 Volt dc or less power source.
2. This product have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limited supplies.
January 23, 2014
4
SIGN COMPONENTS MANUAL (SAM)
3. This Class 2, low voltage, low energy LED controllers when connected to a Class 2 circuit, are not to draw a total wattage of
greater than the secondary or output rating of the Class 2 circuit.
4. This product is suitable for use in indoor, dry locations only.
POLYMER COMPOSITE ASIA SDN BHD
ARAB-MALAYSIAN INDUSTRIAL PARK
PLOT 3266 JALAN AM 1
71800 NILAI, NEGRI SEMBILAN MALAYSIA
E310995
LED Light Bar, Cat. Nos. RED BAR.
1. These products are only suitable for connection to a Class 2 power source rated max. 60 V DC or less for indoor applications
and rated max 30V dc or less for outdoor application. 30 Vrms and 42.4 V peak in dry and damp locations, or 15 Vrms and 21.2
V peak in wet contact locations.
2. When units are connected to a Class 2/”LPS” circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2/”LPS” supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products described in this section have a minimum length of 1.4 m ( 4.59 ft) and a maximum length of 2.7 M (8.86 ft) per
manufacture installation instructions.
5. The LED Light Cat. No. Red Bar has not been evaluated as enclosure or diffuser. Suitability shall be determined in the end use
product.
6. When these products are used in applications other than signs or Outline lighting, the need to conduct a temperature test shall
be considered.
7. These Class 2 LED modules are only suitable for use in Canada, when marked with Class 2 input voltage of less than 42.4 V
DC rating.
8. Spacings between low voltage wiring and uninsulated live parts of the LED Light Cat. No. Red Bar and any line voltage in the
end product shall comply with the spacing requirements in the end use application.
PROCESS DISPLAYS CO
7125 SANDBURG RD
MINNEAPOLIS, MN 55427
E361442
Electric Signs, Class 2, Light Box Assembly; Model No. AS2.0.
1. This product is only suitable for connection to a UL Listed or Recognized Class 2, 24 Volt dc or less power source.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limited supplies.
3. This product is suitable for use in indoor, dry locations only.
4. The suitability of the mounting means is to be determined in the final application.
RTC INDUSTRIES INC
2800 GOLF RD
ROLLING MEADOWS, IL 60008
E164925
LED Portable Signs, Model Nos. L-i-8-3.8, L-i-14-4.5, L-i-19-8.5, L-i-31-13.8.
1. These products shall be used within its Recognized ratings as specified above.
2. These units are only suitable for use in indoor Portable Electric Signs.
3. The units were submitted and tested for a maximum manufacturers recommended ambient of 25ºC. Consideration should be
given for a temperature test when spaced closer than 1 in. end-to-end or 4 in. in any other direction.
4. Do not exceed 300 Watts total power and 3Amps when interconnecting adjacent LED Light Fixtures.
5. Suitable grounding is considered necessary for sign application and shall be evaluated in the end use product evaluation.
6. The product is suitable for use in dry or damp locations.
7. The maximum distance between interconnected LED Light Fixture, must not be more than 2m (79 in.)
8. Suitability of the cord length shall be determined in the end use application.
LED Edge Lit Panels, Model Nos. LEP, LDP Series.
1. These LED Modules are only intended for use with a LPS or Class 2 output power sources.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products shall be used within its Recognized ratings as specified above.
4. These LED Modules are suitable for use in dry and damp locations.
5. These LED Modules are not provided with a mounting means. The suitability is to be determined in end product use.
6. The suitability of supply means shall be determined in end product.
7. The panel shall not function as an enclosure in the end use.
CHANGING MESSAGE SIGNS
(UYFS2, UYFS8)
A component is suitable for the end-use product, if the Conditions of Acceptability identified by the letters (A, B, C, etc.) next to the
model designation or catalog number in the individual Recognitions. The following is a list of Conditions of Acceptability that may
be applicable to each component covered under this category.
A. Suitable for use outdoors when so designated and only where located to prevent rain, snow and the like from coming into
direct contact as determined by the Water Exclusion Test in UL 48.
B. Suitable for use only when contained in an end-product compartment that is a complete electrical enclosure.
C. Suitable for use only when spaced from heat producing components at least:
1. One inch from transformers, ballast, high output fluorescent electrodes and electric discharge tubing;
5
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. Two inches from incandescent and HID lampholders;
3. Nine inches from incandescent and HID lamps rated 250 watts or less; and,
4. Twelve inches from incandescent and HID lamps rated 251-400 watts.
D. Suitable for use only when made inaccessible to contact by users during user maintenance while energized.
E. Not provided with supply and/or output connection means suitable for field wiring.
F. These components are suitable for use with no spacing between themselves.
Z. Refer to additional Conditions of Acceptability included in the individual Recognition report for this component.
CHAINZONE TECHNOLOGY CO LTD
NANXIN YI RD
GUICHENG
NANHAI DISTRICT
FOSHAN, GUANGDONG CHINA
E302683
Changing Message Sign, Models MO13, M016, MO18, MO20, MO25, MO32, MO40 may be followed xxx, where xxx may be
replaced by any alphanumeric characters.
Applicable Conditions of Use – A, B, E, Z.
The following are the additional “Z” conditions of use:
1. The materials provided in the module are suitable for use in permanently connected signs when a suitable enclosure around
the sides of the LED module is provided in the end use application. The operating temperature of the polymeric materials
and printed wiring board shall not exceed 110 C in the end product.
2. Wiring and means of connection between modules shall be investigated in the end product requirements.
3. The power supply to power the LED module is to be provided in the end product. Therefore, testing of these Modules will
need to be conducted in the end product.
Changing Message Sign, Models VFO Series, may be followed by XX-YYYYY-ZZZZZZZ, where these can be any alphanumeric
characters.
Applicable Conditions of Use – Z.
The following are the additional “Z” conditions of use:
1. The side of the LED module is rated V0. A suitable enclosure around the side of the LED module shall be considered in the
end product.
2. Acceptability for multiple connections (daisy chain) not exceeding 16 A shall be determined by the end product requirements.
3. This product was tested for use at room ambient temperature of 25°C. Testing was conducted in the following conditions:
a. Unit operating with ventilation fans operating.
b. Unit operating with ventilation fans disconnected.
c. Unit operating with ventilation fans operating and branch circuit loaded with 16 Amps resistive load simulating through wiring.
At higher ambient temperatures consideration for conducting temperature shall be considered by the end product
requirements. The temperature of the polymeric housing shall not exceeding 115°C.
4. The suitability of the mounting means shall be determined in the end use.
5. The Rain Test per UL 879 was performed with the product in vertical upright position. Suitability for outdoor use when
installed shall be considered by the end product requirements.
6. The Abnormal Test (Component Fault and Locked Fan) was performed on the product. Consideration to perform additional
components for Fault Test shall be determined by the end product requirements.
DAEHAN ULTRAVISION CO LTD
596-3 JANG HANG-DONG, ILSAN-KU
KOYANG-SHI
KYONGGI-DO 411-834, KOREA
E205267
LED Changing Message Sign Modules, Cat. Nos. DE-320-UP, DW-320-UP.
Applicable Conditions of Use – E, Z.
The following are the additional “Z” conditions of use:
1. The suitability of these components must be evaluated in the end product. This includes the applicable tests, such as input,
Temperature, Leakage Current or Dielectric Voltage Withstand and Abnormal Tests.
2. The materials provided in the module are suitable for use in permanently connected signs when the operating temperature
of the polymeric materials and printed wiring board do not exceed 105°C.
3. No wiring is provided with these modules.
4. These modules are suitable for use in outdoor signs when the sign has been determined to comply with the Water Exclusion
Test in UL 48.
LED Changing Message Sign Modules, Cat. Nos. DW-160-UP, DW-160-UF, DW-500-UP.
Applicable Conditions of Use – E, Z.
The following are the additional “Z” conditions of use:
1. The suitability of these components must be evaluated in the end product. This includes the applicable tests, such as input,
Temperature, Leakage Current or Dielectric Voltage Withstand and Abnormal Tests.
2. The materials provided in the module are suitable for use in permanently connected signs when the operating temperature
of the polymeric materials and printed wiring board do not exceed 105°C.
3. No wiring is provided with these modules.
4. These modules are suitable for use in outdoor signs when the sign has been determined to comply with the Water Exclusion
Test in UL 48.
FUTUREMEDIA DISPLAYS INC
#800 2120 HUTTON DR
CARROLLTON, TX 75006
Changing Message Sign, Models FMD followed by 9, 12, 15, 18 or FMD24 may be followed by suffixes.
E215616
January 23, 2014
6
SIGN COMPONENTS MANUAL (SAM)
Applicable Conditions of Use – A, B.
Changing Message Sign, Models FMTNNH-AAC-X-GG where "T" can be any letter, "NN" can be any number from 0 to 9, "H" can
be blank or any alphanumeric character, "AA" can be any letter, "C" can be any letter, "X" can be blank, 3, 5, 7 or 9, and "GG" can
be blank or any alphanumeric character.
Applicable Conditions of Use – A, B.
OLSEN GAMING INC, DBA SPECTRONIX
SUITE G
6285 S MOJAVE RD
LAS VEGAS, NV 89120
E257157
Changing Message Sign Module, Cat. Nos. Model LED "Dot Matrix Display XX Series", where XX may be replaced by any letters
of alphabet from A to Z or numbers from 0 to 9 or combination.
Applicable Conditions of Use – Z.
The following are the additional “Z” conditions of use:
1. These products are not provided with enclosure. The suitability of electrical enclosure shall comply with enclosure
requirements of end product Standard.
2. No temperature test is considered necessary when this product is provided in an enclosure box with dimensions not less
than 90 by 22 by 21 cm.
3. Suitable for use only when all live parts made inaccessible to contact by users during user maintenance while energized.
4. Suitable for use in dry location only.
5. The products shall be grounded in the end product.
6. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
7. Power supply spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 6 inches.
OPEN NV
GELAAGSTRAAT 53
9150 RUPELMONDE
BELGIUM
E243613
LED Display Unit, Cat. Nos. Zephyr_04SSRU, Zephyr_04FSRU, Zephyr_04SDRU, Zephyr_04FDRU, Mistral_15SSRU,
Mistral_15FSRU, Mistral_15SDRU, & Mistral_15FDRU with suffix “_wwww.hhhh.ddd”.
Applicable Conditions of Use – A, C.
OPTEC DISPLAYS INC
716 S NOGALES ST
CITY OF INDUSTRY, CA 91748
E204188
LED Display Unit, Cat. No. 24VGABOXZZZZ2.1ZZZ
Applicable Conditions of Use – Z.
The following are the additional “Z” conditions of use:
1. The suitability of this controller to control a changing message sign shall be determined in the end use.
PALTRONICS INC
9246 TRINITY DR.
LAKE IN THE HILLS, IL 60156
E250835
Changing Message Sign Main Power Supply, Controller, Alternate Controller and Sign Display
Cat. Nos. SP320-5N-CASE-R1, CTRL580-IGT, CTRL580-PAL, & DP48X6-4 F.
Applicable Conditions of Use – Z.
The following are the additional “Z” conditions of use:
1. The materials provided in the module are suitable for use in cord connected indoor use signs.
2. The power supply and controller have been evaluated for use in a indoor dry location.
3. The suitability of these components must be evaluated in the end product. This includes the applicable tests, such as
input, Temperature, Leakage Current or Dielectric Voltage Withstand and Abnormal Tests.
4. The insulation system for the transformer in the power supplies is Class A.
SHENZHEN LIANTRONICS CO LTD
1-5/F 4 BLDG ANTONGDA
INDUSTRIAL ZONE 3RD LIUXIAN RD
68 BLK, BAO'AN DISTRICT
SHENZHEN, GUANGDONG 518101 CHINA
E334083
LED Changing Message Sign Unit, Model No. Models PH16, and PH25. Indoor LED Changing Message Sign PH5.08.
Applicable Conditions of Use E, F, Z.
The following are the additional “Z” conditions of use:
1. The suitability of the mounting means shall be determined in the end use.
2. The devices are for connection to a 20 A maximum branch circuit.
3. The suitability of the module data and power supply connections shall be determined.
4. The need for a temperature test of the complete sign when provided with an additional enclosure should be determined.
5. The Model PH-5.08 modules are suitable for indoor use only.
7
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
6. The Model PH-16 and PH-25 modules are for outdoor use but can only have the sign face exposed to weather. The back of
the sign assembly shall be housed to prevent water entry as determined by the Water Exclusion Test.
7. Suitability of gaskets between adjacent modules should be determined.
YOUNG ELECTRIC SIGN CO
5119 S CAMERON ST
LAS VEGAS NV
89118
E176781
Changing Message Sign Module, Cat. No. Price Changer.
Applicable Conditions of Use – Z.
The following are the additional “Z” conditions of use:
1. Suitable for use only when all live parts made inaccessible to contact by users during user maintenance while energized.
2. Front area of sign suitable for use in wet location only, the rest of the unit including the supply connection suitable for dry and
damp locations only.
3. When installed, the back of sign shall be recessed to prevent any exposure to wet location or rain.
4. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
5. Power supply spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 6 inches.
6. The device and wirings are intended for use in a suitable electrical enclosure which prevents mechanical abuse, such as
impact, terminal stress or current interruption.
7. Bonding test should be considered in the end product investigation. The Power Supply proper bonding to the end-product
main protective earthing termination is required.
Changing Message Sign Module, Cat. No. Booter Model NP-02.
Applicable Conditions of Use – Z.
The following are the additional “Z” conditions of use:
1. These components should be installed in accordance with the manufacturer’s installation instructions.
2. In the end product, the spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
3. These products are suitable for use in dry locations.
4. These power supplies are rated as the following:
Model Designation
Booter model NP-02
Input Voltage (Vac)
Max. Input Current (A)
Input Frequency (Hz)
120
12
60
SIGN ACCESSORIES
(UYMR2, UYMR8)
3A COMPOSITES USA INC
208 W 5TH ST
PO BOX 507
BENTON, KY 42025
E101623
Structural Panel, designated "ALUCOBOND" made 3 mm, 4 mm or 6 mm of polyethylene laminated on two sides with aluminum.
1. This product is intended as an outer decorative covering, has not been investigated for use as an electrical enclosure.
2. The use of this product is limited to only decorative and sign body applications.
3. The suitability of the "fit" of the face material and the "secureness" of the clamp mechanisms on the sign, will be judged in the
end use sign application.
4. This product is acceptable for use in dry, damp and wet locations
5. The water exclusion must be determined in the end product.
6. This product suitable for use in terminating conduit.
7. All components other than neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers of
minimum 7/16-in diameter.
8. All exposed edges of a structural panel, including drilled holes, etc., are be treated with two coats of outdoor paint or wood
coating.
9. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in from a
point of support.
10. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
11. ALUCOBOND" panels provided with letter cutouts, in which 1/8 in. thick thermoformed acrylic shaped letters are pushed
through the panel cutout, have an additional 1/8 in. flange around the periphery to prevent the acrylic face from falling out of
the sign enclosure. These acrylic letters are mechanically attached to the backside of the "ALUCOBOND" on 1/4-20 threaded
studs. The studs are swaged or welded to a 2 by 2, No. 16 gauge perforated galvanized steel plate. The stud assembly is, in
turn, secured with bolts, screws, rivets or welding, to the "ALUCOBOND" panels.
Structural Panel, designated "DIBOND" made 2 mm, 3 mm, or 4 mm of polyethylene laminated on two sides with aluminum.
1. This product is intended as an outer decorative covering, has not been investigated for use as an electrical enclosure.
2. The use of this product is limited to only decorative and sign body applications.
3. The suitability of the "fit" of the face material and the "secureness" of the clamp mechanisms on the sign, will be judged in the
end use sign application.
4. This product is acceptable for use in dry, damp and wet locations
5. The water exclusion must be determined in the end product.
6. This product suitable for use in terminating conduit.
January 23, 2014
8
SIGN COMPONENTS MANUAL (SAM)
7. All components other than neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers of
minimum 7/16-in diameter.
8. All exposed edges of a structural panel, including drilled holes, etc., are be treated with two coats of outdoor paint or wood
coating.
9. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in from a
point of support
10. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
Structural Panel, designated Sintra Material.
1. This product is intended as an outer decorative covering, has not been investigated for use as an electrical enclosure.
2. The use of this product is limited to only decorative and sign body applications.
3. The suitability of the "fit" of the face material and the "secureness" of the clamp mechanisms on the sign, will be judged in the
end use sign application.
4. This product is acceptable for use in dry, damp and wet locations
5. The water exclusion must be determined in the end product.
6. This product suitable for use in terminating conduit.
7. All components other than neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers of
minimum 7/16-in diameter.
8. All exposed edges of a structural panel, including drilled holes, etc., are be treated with two coats of outdoor paint or wood
coating.
9. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in from a
point of support
10. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
11. The proximity of heat producing parts (i.e: transformers, power supplies, ballasts, electrode receptacles, etc.) to this material
shall comply with the requirements of UL 48.
3M COMPANY 3M COMMERCIAL GRAPHICS DIV
BLDG 207-BW-09
3M CENTER
ST PAUL MN 55144
E65361
Flexible sign face material, Flexible sign face systems for use in electric signs designated 3M™ Panaflex™ Awning and Sign
Facing 945 GPS; 3M™ Panaflex™ Awning and Sign Facing 945GPS; GPS with Built-in Color; 3M™ Panaflex™ Plus Awning &
Sign Facing Series 3000, Series 4000, Series 4050 HG Pre-decorated products.
1. Suitable for use in outdoor signs.
2. Not suitable for use as an electrical enclosure.
3. Suitable for use with Recognized Component Securement and Tensioning systems.
4. Securement and tensioning systems shall reliably secure the face to the sign and pull the face taut in all directions.
5. Clamps, hooks, etc., individually attached to the Panaflex and sign cabinet shall be spaced around the sign perimeter at
maximum 3 ft. intervals.
Flexible sign face systems, designated 3M(TM) PANAGRAPHICS (TM) II Intermediate Flexible Substrate.
1. The suitability of the Panagraphics II or III when used on an outdoor sign to prevent entrance of water shall be determined in the
end application.
2. The suitability of the mounting and securing of the product shall be determined in the end product.
3. The Panagraphic II or III shall comply with the external decorative face spacing requirements of UL 48.
4. The Panagraphics II or III has not been investigated for use as an electrical enclosure.
5. When the Panagraphics II or III materials are used in sections in excess of 6 feet, suitable internal bracing of the signs should
be employed to provide the necessary mechanical support for the tensioned face and prevent the material from contacting
arcing or heat sources.
Flexible Sign Face systems, 3M(TM) PANAGRAPHICS (TM) III Wide Flexible Substrate .
1. The suitability of the Panagraphics II or III when used on an outdoor sign to prevent entrance of water shall be determined in the
end application.
2. The suitability of the mounting of the and securing of the product shall be determined in the end product.
3. The Panagraphic II or III shall comply with the external decorative face spacing requirements of UL 48.
4. The Panagraphics II or III has not been investigated for use as an electrical enclosure.
5. When the Panagraphics II or III materials are used in sections in excess of 6 feet, suitable internal bracing of the signs should
be employed to provide the necessary mechanical support for the tensioned face and prevent the material from contacting
arcing or heat sources.
Flexible Sign Face systems, Light enhancement film material, designated 3M(TM) Light Enhancement Film 3635-100.
1. The use of this reflector system shall be employed in applications wherein the limitations as set forth in Table A are not
exceeded.
2. This system may be used for securement to any combination of surface listed in Table A, provided the use temperature is not
higher than the lowest temperature rating of any element of the combination.
3. This system may be used for any illuminated product provided with high output fluorescent, fluorescent, compact fluorescent,
and neon at zero clearance.
4. This system is also suitable for indoor and outdoor use within a housing where exposed to high humidity or occasional exposure
to water. The minimum temperature rating is -35C.
5. This system is suitable for application to clean, flat surfaces identified below. Other surfaces require further evaluation.
6. This material has been evaluated for adhesive compatibility, stability, and flammability (94HB). No electrical tests have been
performed. The engineer must consider the need to investigate the part of other than the properties investigated, in accordance
with the applicable UL end-product standard or requirements outlined in the Standard for Polymeric Materials - Use in Electrical
Equipment Evaluation, UL 746C.
9
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
7. The suitability of the film for use when exposed to oil, chemicals, refrigerant, soaps, x-rays, ultraviolet light and the like has not
been determined by this investigation.
TABLE below
Substrates
Max.Temp. Rating, C
Aluminum painted with acrylic paint
90
Bare Aluminum
90
Steel painted with acrylic paint
90
Polycarbonate
90
Acrylic
90
Note - Polycarbonate and acrylic substrates additionally must have suitable temperature ratings for each application.
Flexible Sign Face systems, Light reflecting film designation 3MTM Daylighting Film DF2000MA.
1. The use of this reflector system shall be employed in applications wherein the limitations as set forth in Table below are not
exceeded.
2. This system may be used for securement to any combination of surface listed in Table A, provided the use temperature is not
higher than the lowest temperature rating of any element of the combination.
3. This system may be used for any illuminated product provided with high output fluorescent, fluorescent, compact fluorescent,
neon, and LED at the thermal spacings specified in UL 48. Additionally, LED drivers, fluorescent ballasts, fluorescent
lampholders, LED modules or strings and neon supplies may be mounted at zero clearance to the reflective film when applied to
metal.
4. This system is also suitable for indoor and outdoor use within a housing where exposed to high humidity or occasional exposure
to water. The minimum temperature rating is -35(C.
5. This system is suitable for application to clean, flat surfaces identified below. Other surfaces require further evaluation.
6. This material has been evaluated for adhesive compatibility, stability, and flammability (94HB). No electrical tests have been
performed. The engineer must consider the need to investigate the part of other than the properties investigated, in accordance
with the applicable UL end-product standard or requirements outlined in the Standard for Polymeric Materials - Use in Electrical
Equipment Evaluation, UL 746C.
7. The suitability of the film for use when exposed to oil, chemicals, refrigerant, soaps, x-rays, ultraviolet light and the like has not
been determined by this investigation.
Substrates
Max. Temp. Rating,
°C
Aluminum painted with acrylic
90
paint
Bare Aluminum
90
Steel painted with acrylic paint
90
Polycarbonate
90
Acrylic
90
Note - Polycarbonate and acrylic substrates additionally must have suitable temperature ratings for each application.
8. The kraft paper adhesive liner is to be removed prior to application and the clear film provided to protect reflective surface is to
be removed prior to final assembly of the product.
Flexible sign face material, Decorative Sign Face Material, 3MTM Chrome Graphic Film, 3635-110.
1. The use of this decorative system shall be employed in applications wherein the limitations are set forth in this report.
2. This system may be used for securement to any combination of surface provided it is adhered outside the sign body.
3. For use inside a sign body, the material will have to be evaluated per Item 4 below.
4. This material has been not evaluated for adhesive compatibility, stability, and flammability (94HB). No electrical tests have been
performed. The engineer must consider the need to investigate the part of other than the properties investigated, in accordance
with the applicable UL end-product standard or requirements outlined in the Standard for Polymeric Materials - Use in Electrical
Equipment Evaluation, UL 746C.
5. The suitability of the film for use when exposed to oil, chemicals, refrigerant, soaps, x-rays, ultraviolet light and the like has not
been determined by this investigation.
Polymeric adhesive systems, electrical equipment, pressure-sensitive adhesive tapes, designated "3M™ VHB™ Acrylic
Adhesive Transfer Tapes" or "3M™ VHB™ Double Coated Acrylic Foam Tapes", F-9460PC, F-9469PC, F-9473PC, 4611, 4615,
4646, 4655, 4905, 4910, 4914, 4919F, 4919P, 4920, 4922, 4926, 4930, 4936, 4936F, 4941, 4941F, 4945, 4946, 4947F, 4947P,
4950, 4956, 4956F, 4979F, 4991, 5915, 5925, 5930, 5952, 5962, 9460PC, 9469PC, 9473PC.
1. The use of these adhesive systems shall be employed in applications wherein the limitations as set forth in Tables A through G
are not exceeded.
2. These adhesive systems may be used for securement to any combination of surfaces listed in the following Tables, provided the
use temperature is no higher than the lowest temperature rating of any element of the combination.
3. These systems are suitable where exposed to high humidity or occasional exposure to water. This would include construction of
outdoor sign cabinets where the joint is not subject to standing water. The minimum temperature rating is -35°C (-31°F).
4. These systems are suitable for application to smooth, flat, clean surfaces. Application to textured or rough surfaces requires
engineering evaluation.
5. The adhesive dynamic bond strength specified in the Tables includes a safety factor of four. When considering the use of any
adhesive covered by this Report, the strength of the adhesive joint used to position parts shall be capable of withstanding the
maximum force that might be applied to the joint in the end application. This is called the dynamic bond strength and includes
wind loading. The minimum square inches of adhesive tape to use is determined by dividing the maximum dynamic load in
pounds by the adhesive bond strength in the Tables to obtain.
6. The adhesive static bond strength is 0.25 pounds per square inch, which is the ability to support the dead weight of a sign panel.
Where the total weight of the panel is supported by other mechanical means such as by a flange, lip, or channel, the static bond
strength calculation is not applicable. The minimum square inches of adhesive tape to use is determined by dividing the
maximum static load in pounds by 0.25 pounds per square inch.
January 23, 2014
10
SIGN COMPONENTS MANUAL (SAM)
7. After determining the amount of tape required in square inches for the static load and for the dynamic load, the largest number is
the minimum amount of tape that shall be used.
8. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed. Additional evaluation is required for uses not specifically identified herein.
9. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been
determined by this investigation.
10. The adhesive shall be applied in accordance with the manufacturer’s instruction. All surfaces shall be clean and dry. The
manufacturers instructions regarding cure time shall be followed. For Tables “NT” – Not Tested.
TABLE A
Bond Strength
Max Temp Rating, C Adhesive Grade
Lbs./inch2
5952
5925 5962
Substrate
Acrylic
10
90
Polycarbonate
10
90
NT
90
Cellulose Acetate Butyrate
7
90
NT
Aluminum
10
90
90
Acrylic/Polyurethane paint
10
90
90
Galvanized steel
10
90
90
Rigid PVC
8
75
75
Polyester paint
10
90
90
TABLE B
Bond Strength
Substrate
Max. Temp Rating, C Adhesive Grade
Lbs./inch2
4922
4945
Acrylonitrile-Butadiene-Styrene (ABS)
10
90
90
Polycarbonate
10
90
90
Phenolic
10
110
110
Aluminum
10
110
110
Galvanized Steel
10
110
110
Stainless Steel
10
NT
90
Enameled Steel
10
110
110
Unplasticized Polyvinyl Chloride (UPVC)
10
75
75
Polyamide Type 6/6 (Nylon)
10
90
90
Acrylic/Polyurethane Paint
10
NT
90
Polyester Paint
10
NT
90
TABLE C
Substrates
Maximum Temperature Rating, C
Bond Strength
Lbs./inch2
Adhesive Grade
4914
4920 4930 4950
4905 4910
Acrylonitrile-Butadiene-Styrene (ABS)
10
75
75
NT
Polycarbonate (PC)
10
75
75
90
10(8 for 4905 & & 4910)
110
110
90
Aluminum
Galvanized Steel
10
110
110
NT
Enameled Steel
10
110
110
NT
Stainless Steel
10
110
110
NT
Rigid Polyvinyl Chloride (PVC)
10
75
75
NT
Glass/Epoxy (Grade G-10, FR-4)
10
110
110
NT
Ceramic
10
110
110
NT
Polybutylene Terephthalate (PBT)
10
90
90
NT
Acrylic
10
NT
90
NT
Acrylic/Polyurethane paint
10
NT
NT
90
TABLE D
Substrates
Bond Strength
Maximum Temperature Rating, C
Adhesive Grades
Lbs./ inch2
4919F, 4919P, 4926, 4936, 4936F, 4941, 4941F,
4956, 44956F, 4979F, 4946, 4947F, 4947P
4991
11
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
Acrylonitrile-Butadiene-Styrene (ABS)
10
75
NT
Polycarbonate (PC)
10
90
90
Aluminum
10
90
90
Galvanized Steel
10
90
NT
Enameled Steel
10
90
NT
Stainless Steel
10
90
NT
Nickel coated ABS
10
90
NT
Rigid Polyvinyl Chloride (PVC)
10
90
NT
Glass/Epoxy (Grade G-10, FR-4)
8
90
NT
Ceramic
8
110
NT
Polybutylene Terephthalate (PBT)
8
90
NT
Glass (with and without silane coating)
8
90
NT
Acrylic/Polyurethane paint
10
90
90
Polyester paint
10
90
90
TABLE E
Bond Strength
Substrate
Maximum Temperature Rating, C
Adhesive Grade 4611, 4646, 4655
Lbs./inch2
10
10
10
10
10
10
10
10
10
10
Stainless Steel
Aluminum
Galvanized Steel
Glass (not silane coated)
Glass/Epoxy - FR4
Phenolic
Nylon
Polycarbonate
Acrylonitrile Butadiene Styrene - ABS
PVC Rigid
110
110
110
110
110
110
90
90
75
75
Substrate
TABLE F
Bond Strength
Lbs./inch2
Acrylonitrile-Butadiene-Styrene (ABS)
10
75
Polycarbonate (PC)
10
90
Aluminum
10
110
Maximum Temperature Rating, C
Adhesive Grade 4615
Galvanized Steel
10
110
Enameled Steel
10
110
Stainless Steel
10
110
Polyvinyl Chloride (PVC)
10
75
Glass/Epoxy (Grade G-10, FR-4)
10
110
Polybutylene Terephthalate (PBT)
10
90
TABLE G
Substrates
BondStrength
Lbs./inch2
Maximum Temp. Rating, °C Adhesive Grades
9473PC, F-9473PC
9460PC, F-9460PC
9469PC, F-9469PC
Acrylonitrile-Butadiene- Styrene (ABS)
10
90
90
90
Polycarbonate
10
90
90
90
Phenolic
10
110
110
110
Aluminum
10
110
110
110
Galvanized Steel
10
90
90
90
Enameled Steel
10
110
110
110
Ceramics
10
110
110
110
Nickel Plated Iron
10
NT
NT
110
Stainless steel
10
110
110
110
Glass/epoxy (G-10, FR-4)
10
110
110
110
Rigid polyvinyl chloride (PVC)
10
75
75
75
Polymeric adhesive systems, electrical equipment, pressure-sensitive adhesive tapes, designated No. 7965MP, 8153LE,
EAD217, 467MP, 467MP, 467MPL, 468MP, 468MPF, 468MPL, 9667MP, 9668MP, 9668MPL, 7952MP, 7952MPL, 7955MP,
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
12
7955MPL, 7962MP, 7962MPL, 9172MP, 9172PT, 9185MP, 9679MP, 7945MP, 7953MP, 7956MP, 7956MWS, 7956WDL, 7957MP,
7959MP, 7961MP, 9045MP, 9056MP, 9057MP, 9057MPW, 9059MP, 9061MP, 7966MWS, 7966WDL.
1. The use of these adhesive systems shall be employed in applications wherein the limitations specified in Table A are not exceeded.
2. These systems may be used for securement to any combination of surfaces Listed in Table A, provided the use of temperature
is no higher than the lowest temperature rating of any element of the combination
3. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed on the adhesive by itself. The Engineer must consider the need to investigate the part of other than the properties
investigated, in accordance with the applicable UL-end product Standard or requirements outlined in the Standard for Polymeric
Materials - Use in Electrical Equipment Evaluations, UL 746C.
4. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been
determined.
5. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position critical
parts shall be capable of withstanding at least four times the maximum force in the as-received condition that might be applied to
the joint in the end application.
6. These systems are suitable for application to smooth flat surfaces. The need for adhesive bond strength test when applied to
another surface or configuration shall be determined in the particular end use application.
7. These systems are also suitable where exposed indoors or outdoors to high humidity or occasional exposure to water. The
minimum temperature rating is -35°C (-31°F).
8. The adhesive static bond strength is 0.25 pounds per square inch, which is the ability to support the dead weight of a sign panel.
Where the total weight of the panel is supported by other mechanical means such as by a flange, lip, or channel, the static bond
strength calculation is not applicable. The minimum square inches of adhesive tape to use is determined by dividing the
maximum static load in pounds by 0.25 pounds per square inch.
9. The adhesive shall be applied in accordance with the manufacturer's instruction. All surfaces shall be clean and dry. The
manufacturers instructions regarding cure time shall be followed.
10. The adhesive dynamic bond strength specified in Table A includes a safety factor of four.
11. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts
shall be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the
dynamic bond strength and includes wind loading. The minimum square inches of adhesive tape to use is determined by
dividing the maximum dynamic load in pounds by the adhesive bond strength specified in Table below.
12. After determining the amount of tape required in square inches for the static load and for the dynamic load, the largest number
is the minimum amount of tape that shall be used.
Adhesive
Adhesive Product
Dynamic Bond Substrate
MaxType (1)
Strength
Temp
Pounds/square
Rating,
inch
°C
5 mil 200MP on
7965MP, 468MP, 468MPF, 9668MP,
5
Urethane Paint 60
different liners.
9668MPL, 9185MP
PTI XUG-0467
5
Polyester Paint Govesan RPB-6547
33
Acrylic Paint E-Coat
200MP group.
467MP, 467MPF, 467MPL, 468MP,
14
Polycarbonate
85
Adhesive caliper
468MPF, 468MPL, 9667MP, 9668MP,
24
Acrylic/Urethane coated
includes 1.5 mil,
7952MP, 7952MPL, 7955MP,
Polycarbonate
2 mil and 5 mil.
7955MPL, 7962MP, 7962MPL,
26
PVC
75
7965MP, 9172MP, 9172PT, 9185MP,
9679MP, EAD217, 7945MP, 7953MP,
7956MP, 7956MWS, 7956WDL,
7957MP, 7959MP, 7961MP, 9045MP,
9056MP, 9057MP, 9057MPW,
9059MP, 9061MP, 7966MWS,
7966WDL
1.5 mil and
467MP, 467MPF, 467MPL, 9667MP,
14
Polycarbonate
85
2 mil 200MP
7952MP, 7952MPL, 7955MP,
24
Acrylic/Urethane coated
Adhesive.
7955MPL, 7962MP, 7962MPL,
Polycarbonate
9172MP, 9172PT, 9679MP, EAD217,
35
Aluminum,
7945MP, 7953MP, 7956MP,
Aluminum coated Steel
7956MWS, 7956WDL, 7957MP,
11
Stainless Steel
7959MP, 7961MP, 9045MP, 9056MP,
9057MP, 9057MPW, 9059MP and
6
Galvanized Steel
9061MP
300 LSE
8153LE
6
Urethane Paint 60
Adhesive
PTI XUG-0467
2
Polyester Paint Govesan RPB-6547
56
Acrylic Paint - E-Coat
Class 2 LED Module, designated 3M™ Flexible Light Mat Model 3635-1XXX
1. These products are only suitable for connection to the provided UL R/C Class 2 DC power source according to the power
source’s UL conditions of acceptability.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
13
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
3. These products may be cut to create voids or segments through any portion on the sheet.
4. Suitable for dry and damp locations.
5. These products are required to be enclosed or protected from weather.
6. These products are intended only for factory installation in new signs.
Class 2 LED Module, Cat. Nos. 3M™ LED High Efficiency Light Panel
1. These products have been evaluated for use only when connected to a power source that complies with Class 2 or LPS
requirements for energy limited power supplies.
2. Suitable for dry and damp locations.
3. These products are required to be enclosed or protected from weather.
4. These products are intended only for factory installation in new signs.
5. Grounding of frame to supply ground is required. Suitability of bonding for grounding connection is to be determined in final
application.
6. Suitability of LED panel mounting shall be determined in final application.
7. Suitability of LED power source shall be determined in the final application.
Polymeric adhesive systems, Cat Nos. DP-810 and DP-810 Black designated “Scotch-Weld”
1. The use of these adhesive systems shall be employed in applications wherein the limitations specified in Table A are not
exceeded.
2. These systems may be used for securement to any combination of surfaces Listed in Table A, provided the use of
temperature is no higher than the lowest temperature rating of any element of the combination
3. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed on the adhesive by itself. The Engineer must consider the need to investigate the part of other than the properties
investigated, in accordance with the applicable UL-end product Standard or requirements outlined in the Standard for
Polymeric Materials - Use in Electrical Equipment Evaluations, UL 746C.
4. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been
determined.
5. These systems are suitable for application to smooth flat surfaces. The need for adhesive bond strength test when applied to
another surface or configuration shall be determined in the particular end use application.
6. These systems are also suitable where exposed indoors or outdoors to high humidity or occasional exposure to water. The
minimum temperature rating is -35°C (-31°F).
7. The adhesive shall be applied in accordance with the manufacturer's instruction. All surfaces shall be clean and dry. The
manufacturer's instructions regarding cure time shall be followed.
8. The adhesive bond strength specified in Table A includes a safety factor of four.
9. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts
shall be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the
bond strength and includes static load as well as wind loading(dynamic load). The minimum square inches of adhesive to use
is determined by dividing the maximum load in pounds by the adhesive bond strength specified in Table A.
TABLE A
Cat. Nos.
DP-810, DP-810 Black
Substrate Combination
Thickness: 0.076 mm (0.003 in)
Max. Operating Temp.
°C (°F)
Adhesive Bond
Strength(PSI)
Stainless Steel to Stainless Steel
60
1000
Aluminum to Aluminum
60
980
Polycarbonate to Polycarbonate
60
180
Magnesium to Magnesium
60
870
Acrylonitrile Butadiene Styrene to Acrylonitrile
Butadiene Styrene
60
310
Cat. Nos.
DP-810, DP-810 Black
Substrate Combination
Thickness: 0.254 mm (0.010 in)
Max. Operating Temp.
°C (°F)
Adhesive Bond Strength
(PSI)
Stainless Steel to Stainless Steel
60
940
Aluminum to Aluminum
60
900
Polycarbonate to Polycarbonate
60
190
Magnesium to Magnesium
60
690
Acrylonitrile Butadiene Styrene to Acrylonitrile
Butadiene Styrene
60
430
3M COMPANY INDUSTRIAL ADHESIVES & TAPES DIV
3M CENTER
BLDG 230-3G-07
ST PAUL, MN 55144
E464624
Adhesives, designated DP84005NS, DP8805NS, DP8810NS.
1. These systems are also suitable for use outdoors where exposed to high humidity or water. The minimum temperature rating is
-35°C (-31°F).
2. Temperature rated to 90C maximum.
January 23, 2014
14
SIGN COMPONENTS MANUAL (SAM)
3. Means need to be provided for grounding metal parts that may become energized.
4. This adhesive system is suitable for application to smooth flat surfaces, except where another surface configuration is noted.
5. The adhesive at a nominal thickness of 0.25mm may be used for securement of any combination of the following surfaces;
aluminum and stainless steel.
6. Adhesive shall be applied in continuous bead when used as water seal.
7. These adhesives are produced in a 10:1 mix ratio by volume (10 parts “B” (base) to 1 part “A” (accelerator).
8. The bond strength values shown in Table A were determined in accordance with ASTM D 1002.
9. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed. The engineer must consider the need to investigate the part for other than the properties investigated, in accordance
with the applicable end-product standard and/or the requirements outlined in UL 746C, Standard for Material Used in Electrical
Equipment Evaluations.
10. The suitability for the use when exposed to oil, chemicals, refrigerant, soap, x-rays, ultraviolet and the like has not been
determined by this investigation, unless otherwise noted.
11. The bond strength value in Table A has been divided by safety factor of four for mechanical strength and specifies the
maximum shear tension load in pounds per square inch of adhesive.
TABLE A
Cat No.
DP8405NS
DP8805NS
DP8810NS
Substrate
Max. Operating
Temp. °C (°F)
Maximum Shear
Tension Load PSI)
Stainless Steel to Stainless Steel
90 (194)
807
Aluminum to Aluminum
90 (194)
912
Stainless Steel to Stainless Steel
90 (194)
727
Aluminum to Aluminum
90 (194)
740
Stainless Steel to Stainless Steel
90 (194)
659
Aluminum to Aluminum
90 (194)
710
AA LED SUPPLY CORP
9441 VALLEY BLVD.
ROSEMEAD, CA 91770
E325964
Class 2 LED modules, Models LS0723x, LS0766x, LS0769x, LS0776x, where that x may be R, G, B or Y indicating LED Color.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
Part No.
Operating
Voltage
Current per
module
Watts per module
LS0723x
12Vdc
40mA
0.48W
LS0766x
12Vdc
30mA
0.36W
LS1769x
12Vdc
75mA
0.90W
LS0776x
12Vdc
60mA
0.72W
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Class 2 LED Modules, Model AA-0766EC-XX, where XX can be any alpha characters or blank to represent different light color
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. These Class 2 LED modules are each rated as noted in the electrical ratings tables. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
ABC SIGN PRODUCTS
2028 SE FRONTAGE RD
FT COLLINS, CO 80525
E80767
Lampholder adapter, Type LH.
1. This device is suitable for use in indoor or outdoor extruded aluminum awning frames.
2. This adapter is intended for use only with Listed, single or double contact, recessed lampholders (Cat. No. 530, Kulka) which
snap-fit into, and are securely held by, the adapter. The lampholder shall be held securely with or without a lamp in place.
3. This adapter is intended to complete the enclosure housing of insulated live parts only.
4. This device shall be installed in an aluminum extrusion in accordance with the "Installation Instructions" supplied by the
manufacturer in the smallest shipping container.
Sign Face Tensioning System, Model ABC.
1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent
entrance of water in outdoor sign applications shall be determined in the end product.
2. This product has not be evaluated for use as an electrical enclosure.
3. Tensioning clips shall be spaced as described in the Installation Instructions.
15
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent
billowing.
5. The mounted assembly of sign face material in these tensioning systems shall comply with the electrical and thermal spacing
requirements of UL 48.
6. These clips have been determined to be suitable with any R/C Flexible Sign Face Material of min. 0.020 inches (0.51mm) thick,
suitability for use with a material of lesser thickness shall be determined in the end product.
ABLE APPLIED TECHNOLOGIES LTD
BOUNDARY HOUSE BUSINESS CENTER
BOSTON MANOR RD
LONDON, W7 2QE UNITED KINGDOM
E329973
Class 2 LED Modules, Model XS-P40XXX-XX series, where XS can be either SS or MS that relates to LED count/resolution and
XXX-XX may be any alphanumeric characters.
1. These LED panel of these products are powered by Class 2 power source rated at max. 15 VDC, 5 amps.
2. These products are suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When provided with a power supply, in the end product the power supply spacing to other heat producing components shall be
minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure.
5. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 limits.
ACROSENTEC CO LTD
253-9 GOCHUN-DONG
UIWANG-SHI , GYEONGGI-DO
437-801 REPUBLIC OF KOREA
E363566
Class 2 LED Modules, Models ASPCH-@-#-24-$-%-&, ASFCH-@-#-24-$-%-&, and ASMX-@-^-24-*-!, where @ can be any 2 to
4 alphanumeric code, # can be any 3 to 5 alphanumeric code, $ can be any 2 or 3 alphanumeric code, % can be any 1 to 4
alphanumeric code, & can be any 3 to 9 alphanumeric code, ^ can be any 3 to 5 alphanumeric code, * can be any 3 to 6
alphanumeric code, ! can be any 2 to 9 alphanumeric code.
1. These products are only suitable for connection to a Class 2 power source rated 27 V DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit limits and is rated 27 V DC or less.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 27 V DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
ADHESIVE SYSTEMS INC
9411 CORSAIR RD
FRANKFORT, IL 60423
E350958
Polymeric adhesive system, Cat. No. MP55420.
1. The use of these adhesive systems shall be employed in applications wherein the limitations specified in Table A are not exceeded.
2. These systems may be used for securement to any combination of surfaces Listed in Table A, provided the use temperature is
no higher than 71°C.
3. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed on the adhesive by itself. The Engineer must consider the need to investigate the part of other than the properties
investigated, in accordance with the applicable UL-end product Standard or requirements outlined in the Standard for Polymeric
Materials - Use in Electrical Equipment Evaluations, UL 746C.
4. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been
determined.
5. These systems are suitable for application to smooth flat surfaces. The need for adhesive bond strength test when applied to
another surface or configuration shall be determined in the particular end use application.
6. These systems are also suitable where exposed indoors or outdoors to high humidity or occasional exposure to water. The
minimum temperature rating is -35°C (-31°F).
7. The adhesive shall be applied in accordance with the manufacturer’s instruction. All surfaces shall be clean and dry. The
manufacturer’s instructions regarding cure time shall be followed.
8. The adhesive bond strength specified in Table A includes a safety factor of four.
9. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts shall
be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the bond
strength and includes static load as well as wind loading(dynamic load). The minimum square inches of adhesive to use is
determined by dividing the maximum load in pounds by the adhesive bond strength specified in Table A.
ADVANCED LIGHTING CONCEPTS INC,
DBA ENVIRONMENTALLIGHTS.COM
SUITE 102
11235 W BERNARDO CT
SAN DIEGO, CA 92127
Class 2 Power Supply, Models 4x60W12VDimX-120AC, 3x96W24VDimX-120AC.
E345129
January 23, 2014
16
SIGN COMPONENTS MANUAL (SAM)
1. These power supplies have been evaluated for use in LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected to
another power source.
5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least
150 mm (6 in) inside.
AGILIGHT INC
SUITE 108
1218 ARION PKY
SAN ANTONIO, TX 78216
E255447
Class 2 LEDs, Cat. No. “SideWinder” may be followed by (Standard) or “SideWinder BL” Cat Nos. LS-A-BBB-GZ; where A (model
or series name, e.g. SideWinder) and BBB (color designation) may be replaced by alphanumeric characters; and Z may be
replaced with alpha characters to denote generation number.
1. These products are only suitable for connection to a UL Listed or Recognized maximum Class 2, 12 V AC or DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit limits.
3. These Class 2 LED modules, are each rated max. 40 Watts per unit, LED module. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp or wet locations.
5. These products are not required to be enclosed or protected from the weather.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
LED array drivers, Models AGI-LP1060-12-GG-240.
1. These power supplies have a single output that complies with Class 2 output requirements.
2. These products are suitable for use in dry, damp and wet locations only.
3. The primary sides of these power supplies are suitable for connection with threaded type conduit only.
4. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 2 inches.
5. When not marked for indoor use only the power supply primary bracket shall be provided with min. 3.5 threads and tapered for
connection to liquid tight conduit fitting.
6. When not marked for indoor use only, all models shall have liquid tight fittings on both primary and secondary circuits.
Class 2 LEDs, designated as "SIGNRAYZ" LS-A-YY-GZ Series, where A and YY may be replaced alphanumeric characters; and
Z may be replaced with alpha characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. Models with designation of Z=2 are suitable for IP 68. Any other number aside from 2 is only suitable for IP 66.
Class 2 LEDs, designated as "SIGNRAYZ MINI", "BOXRAYS BOLD" or "BOXRAYZ LITE"PCA-XXXXY-ZZT Series, where XXXX
and ZZ may be any alphanumeric characters; and YY and Z may be any alpha characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. These products are suitable for IP 68 designation.
Class 2 LEDs, designated as “SignRayz® PRO160”, “SignRayz® PRO215”, “SignRayz® PROCLR”, “SignRayz® PROMIN”,
“SignRayz® PRO115” or “SignRayz® PROCLR” LS-PROXXX-YYY-#ZZ; where XXX, YYY, # and ZZ may be combinations of any
alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. These products are suitable for IP 68 designation.
Class 2 LED modules, designated as "BoxRayz™ 400", BoxRayz 600 and LS-BOXXXX-YYY-#ZZ Series, where XXXX, YYY, #
and ZZ may be combinations of any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
17
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. These products are suitable for IP 68 designation.
AION LED INC
SUITE 330
2325 3RD ST
SAN FRANCISCO , CA 94107
E348513
LED Lighting Modules, Cat. No. AION LED MODULE 200 SERIES.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, Model AION LED MODULE 100 SERIES.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, AION LED STRIP LIGHT X-X SERIES, where X-X can be any alpha-numeric combination denoting LED
color.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, AION LED MODULE 500 SERIES.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Lighting Modules, Cat. No. AION LED MODULE 600 SERIES.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 0.72 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 output LED drivers, Models D60-M1, D60-M.
1. These products are to be used in maximum 50ºC ambient.
2. These products are provided with Class 2 output.
3. These products are intended for used in a maximum 20 A branch circuit.
4. These products are intended for use in dry and damp locations only.
5. These models are provided with 18 AWG input and output leads. The suitability of the wire shall be considered in end product
use.
6. These LED drivers shall be grounded through its mounting ears when used in end products.
7. These LED drivers are to be used in fixed wiring equipment only.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
Class 2 output LED drivers, Models D100-M-24, D60-M-24,
1. When used in end product, the maximum temperature on case surface shall not exceed the temperature note as below:
Model No.
Degree, ºC
Tested ambient, ºC
D100-M-24
89
60
D60-M-24
90
2. These products are provided with Class 2 output.
60
January 23, 2014
18
SIGN COMPONENTS MANUAL (SAM)
3. These products are intended for used in a maximum 20 A branch circuit.
4. These products are intended for use in dry and damp locations only.
5. These models are provided with No. 18 AWG input and min. No. 22 AWG output leads. The suitability of the wire shall be
considered in end product use.
6. These LED drivers shall be grounded through its mounting ears when used in end products.
7. These LED drivers are to be used in fixed wiring equipment only.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
Class 2 output LED drivers, Models D100-X-24, D100-X4-24.
1. These drivers with metallic housing or display/keys are to be used in the suitable end product fire enclosure.
2. These products are intended for used in a maximum 20 A branch circuit.
3. These products are intended for use in dry and damp locations.
4. These LED drivers shall be grounded through its mounting ears when used in end product.
5. These models are provided with No. 18 AWG input and min. No. 22 AWG output leads. The suitability of the wire shall be
determined in end product use.
6. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
7. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
Class 2 LED modules, AION LED MODULE 500 SERIES or K and XX may be any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED modules, AION LED MODULE 600 SERIES.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 0.72 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Power supplies with Class 2 output circuits, D100-Z-24.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. Suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
5. When not marked for “Dry and Damp Locations Only” the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be
provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
6. These products are suitable for use in commercial application only when marked with 277 V input voltage.
7. When provided with the alternate plastic conduit caps (not metal), the power supply shall be provided with an additional fire
enclosure.
8. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
9. Provided with a dimming option for use with a 0-10VDC dimming system.
ALLANSON INTERNATIONAL INC
33 CRANFIELD RD
TORONTO, ONTARIO, CANADA M4B 3H2
E251622
LED Drivers, Models CV14184, CV125, CV144, CV184, CV243 and LC6012-120 power supplies, Model ACLGWHO6,
ACLGWHO3 glacier white high output LED strip, Model ACLCW6, ACLCW3 cool white LED strip, and Model ACLRR6, ACLRR3
red LED strip.
1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2. The output terminals are suitable for field wiring.
3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40(C.
4. Leakage current measurements shall be performed when more than four LED power supplies are used in the equipment or
when the LED driver is used in combination with other equipment in the end-use product.
5. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
19
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
6. The power supply is suitable for dry and damp location use.
7. If the power supply is mounted where wiring can contact the enclosure, the wiring shall be rated min. 75 C.
Class 2 LED illuminations, Models ACLW -m R 2@, ACLW-mG2@, ACLW-mO2@, ACLW-RGB@, ACLW-WHO@, ACLWmCW2@, ACLW-mWW2@, ACLW-mY2@, ACLW-mB2@.
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 15 V.
3. Class 2 LED Modules Cat. Nos. ACLW -m R 2@, ACLW-mG2@, ACLW-mO2@, ACLW-RGB@, ACLW-WHO@, ACLWmCW2@, ACLW-mWW2@, ACLW-mY2@, ACLW-mB2@ are each rated max. 3 watts per unit. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED illuminations, Models ACLW-5CW2#, ACLW-5WW2#, ACLW-5R2#, ACLW-5Y2#, ACLW-5B2#, ACLW-5G2#.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. These products are each rated max. 7 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means
available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
LED Drivers, Models LC-1012-120, CV121, LC-12012-120, CV12125, LC-6042-MV, CC2C42700MV, CC1C42700MV,
DCC2C42700MV, DCC1C42700MV.
1. These power supplies have a maximum of two Class 2 outputs. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations.
3. The product was tested for use at the maximum ambient temperature (Tma) of 40 C permitted by the manufacturer's
specification.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. Models DCC2C42700MV and DCC1C42700MV are provided with a Dimming circuit. Dimming of the outputs is by using a
potentiometer. The dimming circuit leads to the potentiometer are considered Class 2.
LED Drivers, Models CV125-MV, CV12125-MV, CV243-MV, CV243-MV-QC and CV243-MV and CV24243-MV.
1. These Class 2 LED power supplies have been evaluated using a resistive load resulting in the electrical rating below.
Input
Output
Model
V ac
Hz
A
V dc
A
CV125-MV
120-277
50/60
0.61
12
5
CV12125-MV
120-277
50/60
1.25
Output 1: 12
Output 1: 5
Output 2: 12
Output 2: 5
CV243-MV
120-277
50/60
0.8
24
3.3
CV243-MV-QC
120-277
50/60
0.8
24
3.3
CV24243-MV
120-277
50/60
Output 1: 24
Output 1: 2.5
Output 2: 24
Output 2: 2.5
2. These units are suitable for use in dry and damp locations.
3. These products are intended for use in a maximum 20 A branch circuit.
4. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing. If multiple power supplies are used in one enclosure the minimum spacing between them shall not less
than 1 inch apart when arranged end-to-end, and not less than 4 inches apart when arranged otherwise.
5. These products shall be grounded through its mounting ears when used in end product.
6. These products shall be provided with an electrical enclosure in the end product unless connected to 1/2 in Trade size conduit.
Class 2 LED Modules, Cat. Nos. ACLW-XX2, ACLW-XX3, ACLW-XX5 Series, where xx can be CW, WW, G, B, R, Y or O.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
@ - suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
# - suitable for use in dry, damp, and wet locations when connected to a Class 2 supply rated max. 24 Volts DC.
LED Driver, Model CV125-120-277.
1. This LED driver has been evaluated using resistive load resulting in the electrical input and output noted on page 1.
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below. Acceptance of higher ambient shall
be determined in end product use.
Model
CV125-120-277
Ta (°C)
40
4. These LED drivers are intended for use in dry and damp locations.
January 23, 2014
20
SIGN COMPONENTS MANUAL (SAM)
5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a
suitable enclosure shall be considered in the end product.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. The need of the grounding means shall be determined in the end product.
8. These LED drivers shall be enclosed within a suitable end product enclosure.
9. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
10. In the end product, LED drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
Class 2 output LED drivers, Model CV122-120.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted below;
Input
Model No.
CV122-120
Output
Voltage (V)
HZ
Current (A)
Power
(W)
120
50/60
0.28
32
Voltage
(Vdc)
Current (A)
12
2
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum 40°C ambient.
4. Model CV122-120 is intended for use in damp locations.
5. Model CV122-120 was provided with AWM leads for input/output connection. The suitability of the wiring and the need for a
suitable enclosure shall be considered in the end product.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. Model CV122-120 shall be grounded through its mounting ears.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure. Otherwise, temperature test shall be conducted.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise. Otherwise, temperature test shall be conducted.
Class 2 LED power supplies, Models CVW125-MV and CVW243-MV.
1. The maximum available parameters from the output of the power modules met the maximum allowable limits for a Class 2
source intended for use in a “WET” Location.
2. The power modules are suitable for use in “DRY”, “DAMP”, or “WET” locations.
3. The modules are intended for used in a maximum 20 A branch circuit.
4. In the end product application, the power supplies spacing to other heat producing components shall be a minimum of 2 inches
spacing to sidewalls, and a minimum of 2 inches spacing. If multiple power supplies are used in one enclosure the minimum
spacing between them shall not less than 1 inch apart when arranged end-to-end, and not less than 4 inches apart when
arranged otherwise.
5. The case shall be reliably connected to earth grounded in end product.
6. The modules shall be installed in accordance with the installation instructions detailed in Illustration #1.
7. When multiple power modules are used in the same end application, the outputs of the power modules are not to be
interconnected. The inter connection of the outputs will result in a risk of fire and/or a risk of electric shock
8. The “IP-68” marking has not been evaluated. Therefore, if required for the completion of the evaluation of the end-use
application, the suitability of the driver must be determined in the end-use application.
Class 2 LED Modules, designated as ACLW-XX-#W series, where XX may be CW, WW or SW, and # may be 1 or 3.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Module, Model ACLW-xx-VLP[%] may be followed by two or three alphanumeric numbers.
1. These products are only suitable for connection to a Class 2 power source rated as below or less.
Model No.
Maximum Input Voltage (V DC)
Current Rating (mA)
ACLW-xx-VLP[%]
15
150
2. Units may be interconnected together by leads during normal use. When unit is connected to a Class 2 source, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
3. This product is suitable for use in dry and damp locations.
4. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
ALUMET SUPPLY
150 LACKAWANNA AVE
9TH HUAXI VILLAGE
PARSIPPANY, NJ 07054
E355230
Structural Panel, Model Aluminum composite panel.
1. Suitable for use in dry, damp and wet locations.
2. Suitable for use in decorative and sign body applications only.
3. Suitable for use in component support applications. When threaded directly into the panels, screws shall be no smaller/finer than
No 10. Suitability of smaller and/or finer screws shall be determined.
4. Rain tightness shall be determined in the end product.
5. Electrical spacings and bonding for grounding shall comply with the end product standard.
6. Suitable for use in terminating conduit in 1/2 in Trade Size.
21
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
7. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
8. These materials are rated 50°C, consideration will need to be given to end product thermal spacings from heat producing
components or temperature test.
9. These materials are available as unpainted aluminum or pre-painted aluminum.
APM HEXSEAL CORP
44 HONECK ST
ENGLEWOOD, NJ 07631
E210026
Toggle Switch Boots, Types N-1002, N1030, N1030 1/2-32, N5030, N5030L, N5030R, N5030S, IN-1030, IN1030 1/2-32,
1131/23, 1131/25, 1131/26, 1131/31, 1131/32, C1131/27, C1131/28, C1131/35, C1131/38, C1132/25.
1. This device is intended to be used in outdoor electric sign applications.
2. The ability of this product to prevent water from entering a switch needs to be evaluated in the end product.
3. The R/C (WOYR2) toggle switch for use with this boot shall comply with the following:
a. The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot.
b. The assembly shall be mounted on the side surfaces of a sign body only.
4. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the enclosure
in which the switch is installed are to be provided in accordance with UL 48.
5. The toggle (switch actuator) shall be metal.
Switch Boots, Types 1231/17, N5045, N5040G, 1231/32, N5040, N5040R, 1231/31, 1231/27, 1231/8, NC3030 7/16-32, N3030,
N3030-2513, NC3030, NC3030-2513, NH3030, NH3030S, NC3030H, N3040
1. This device is intended to be used in outdoor electric sign applications.
2. The ability of this product to prevent water from entering a switch needs to be evaluated in the end product.
3. The R/C (WOYR2) toggle switch for use with this boot shall comply with the following:
a. The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot.
b. The assembly shall be mounted on the side surfaces of a sign body only.
4. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the enclosure
in which the switch is installed are to be provided in accordance with UL 48.
5. The toggle (switch actuator) shall be metal.
Switch Boots, Types 1111/7, 1113/62, 1113/63, C1111/7, C1113/62, C1112/63, C1113/66, C1113/70, C1113/71, C1113/75
1. These devices are intended to be used in outdoor electric sign applications.
2. The ability of this product to prevent water from entering a switch needs to be evaluated in the end product.
3. The R/C (WOYR2) toggle switch for use with this boot shall comply with the following:
a. The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot.
b. The assembly shall be mounted on the bottom or side surface of a sign body only.
4. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the enclosure
in which the switch is installed are to be provided in accordance with UL 48.
Switch Boots, Types Cat. Nos. 60064, 60225.
1. These devices are intended to be used in outdoor electric sign applications.
2. The ability of this product to prevent water from entering a switch needs to be evaluated in the end product.
3. The R/C (WOYR2) toggle switch for use with this boot shall comply with the following:
a. The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot
b. The assembly shall be mounted on the bottom or side surface of a sign body only.
4. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the enclosure
in which the switch is installed are to be provided in accordance with UL-48.
ARLON GRAPHICS LLC
2811 S HARBOR BLVD
SANTA ANA, CA 92704
E80939
Flexible sign face systems for use in electric signs, designated "FLEXFACE", "FLEXFACE FX", "MPF" or "MPG",
"FLEXFACE PO", "FLEXFACE S & R", "Flexface PO - CA Fire Marshall Rated", Flexface NF, Flexface GF, Flexface NFX, Flexface
GX, Cast Flex 10, Eradicolor, Flexface TC, ColorKote TC, and Kolorite.
1. The suitability of the sign body and the flexible materials to prevent entrance of water in outdoor sign applications, shall be
determined.
2. The sign face materials shall comply with the external decorative face requirements of UL 48.
3. The materials covered by this Report have not been investigated for use as an electrical enclosure.
4. When the flexible face materials are used on signs with any dimensions (length or width) in spaces greater than 6 ft., suitable
braces should be employed to prevent the material from bellowing (moving after installation) and creating short (reduced)
spacings to heat sources.
Flexible sign face systems for use in electric signs, designated "Wide Print Flex".
1. The sign face material covered by this Report has not been investigated for use as an electrical enclosure.
2. The materials have been evaluated for HB flammability in accordance with UL 879.
3. The temperature limits is 50°C. No electrical or mechanical tests have been performed.
4. This material is suitable for outdoor sign, the suitability of the sign body and the flexible materials to prevent entrance of water
in outdoor sign applications, shall be determined.
5. Suitable for use with all Recognized Component Securement and Tensioning systems. Securement and tensioning systems
shall reliably secure the face to the sign and pull the face taut in all directions.
Flexible non-enclosure rated sign face material, designated "DPF 390" and "Flexface FX version 2" sign face.
1. These flexible non-enclosure rated sign face materials are only suitable for use as decorative parts.
2. These products are suitable for use in dry locations only.
3. These products are limited for use in decorative sign face applications.
January 23, 2014
22
SIGN COMPONENTS MANUAL (SAM)
4. The flexible sign face non-enclosure rated material is not suitable for use as an electrical enclosure.
5. A minimum of 5 cm (2 in.) spacing from heat producing components is required.
6. Not intended for mechanical support of components.
ARTEMEDIA WORLDWIDE LTD
6/F LUK KWOK CENTRE
72 GLOUCESTER RD WAN CHAI
HONG KONG, HONG KONG
E357752
LED Modules, LPS/Class 2 type, Models artemedia LED textile frame 180x120, artemedia LED textile frame 180×100.
1. These LED Modules are only intended for use with a LPS or Class 2 output power sources.
2. These LED Modules are suitable for use in dry and damp locations.
3. These LED Modules are not provided with a mounting means. The suitability is to be determined in end product use.
4. The temperature rating of LED board is 105°C min., of supply leads is 90°C min., and of Light Guide Panel is 50°C min. The
suitability is to be determined in end product use.
5. The suitability of supply means shall be determined in end product.
ARTWARE TELECOMUNICATION CO LTD
806 ACE TECHNO TOWER 1ST
GUTO-GU
SEOUL, REPUBLIC OF KOREA
E313732
Class 2 LED Modules (Clusters), Cat. Nos. AWL-4500C-A, AWL-2500C-A, AWL-4500C-LF.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 12 V.
3. Class 2 LED Modules (“Cluster”), Cat. No.AWL-4500C-A, AWL-2500C-A, and AWL-4500C-LF are each rated max. 6 Watts per
unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Controllers, Models Nos. AWL1200M, AWL1400M, AWL1800M.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 Volt dc or less power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These Class 2, low voltage, low energy LED controllers when connected to a Class 2 circuit, are not to draw a total wattage of
greater than the secondary or output rating of the Class 2 circuit.
4. These products are suitable for use in dry and damp locations.
ASTRODYNE CORP
375 FORBES BLVD
MANSFIELD, MA 02048
E310222
Class 2 LED Illumination Module, Cat. Nos. ALD60-xyyz-FC Series, where x can be 1 or 2; yy can be 05, 06, 08, 10, 12, 15, 18,
21, 24 or 48 and z can be C, D, E or F.
1. These power supplies have a maximum of two Class 2 outputs. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. Power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2
inches spacing to top of enclosure.
4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
Class 2 LED Illumination Module, Model ALD120-xyyz-FC Series, where x can be 2; yy can be 08, 10, 12, 15, 18, 21, 24, 27, 36
or 48 and z can V.
1. These power supplies have maximum of two Class 2 outputs. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations, except models SLD120-236V-FC
and SLD120-248V-FC are suitable for use in dry and damp locations due to output voltages above 30 V dc.
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
4. When used in wet locations, each unit shall be provided with listed (QCRV) and CN 1/2 inch liquid tight conduit fittings.
ATEX CO LTD
HIRAKEN BLDG
2-3-20 TOUKOU
HAKATA-KU
FUKUOKA-SHI, FUKUOKA-KEN 812-0008 JAPAN
E304657
Class 2 – 12, 15, 24 VDC, LED Rope Assemblies, Class 2 LED String Assembly, Series Designation FL10-VWXY-Z, SP10VWXY-Z, CL10-VWXY-Z, CH10-VWXY-Z.
1. For a portable indoor sign, these products are suitable for connection to a 12VDC, 0.5A, UL Listed Class 2 power supply.
2. For all types of signs, these products are suitable for use with a 12 VDC, R/C (UYMR2) Class 2 power supply.
23
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
4. These products are suitable for use in dry, damp, and wet locations.
5. Lead wires do not have a voltage rating and are not R/C AVLV2 wiring. Lead wires must be separated from circuits of other
voltages in the end application.
6. Each 96 LED rope is rated Class 2, 12 VDC, 0.5A.
Class 2, 12 VDC Class 2 LED Module, LED Module: Series LM Series, followed by 01 through 99, followed by 01 through 99,
followed by 1 through 9, followed by AA through ZZ, followed by 1 through 9, followed by 0 through Z.
1. For a portable indoor sign, these products are suitable for connection to a 12/24 VDC, 0.125/0.0625 A, UL Listed Class 2
power supply, minimum.
2. For all types of signs, these products are suitable for use with a 12/24 VDC, R/C (UYMR2) Class 2 power supply.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
4. These products are suitable for use in dry, damp, and wet locations.
5. Lead wires do not have a voltage rating and are not R/C AVLV2 wiring. Lead wires must be separated from circuits of other
voltages in the end application.
6. Each LED module is rated Class 2, 12/24 VDC, 0.125/0.0625 A.
AUTEC POWER SYSTEMS INC
667 E COCHRAN ST
SIMI VALLEY, CA 93065
E364207
Class 2 power supply, Model LEDWV-096S024ST-xxx, where "xxxx" can be any alphanumeric character or blank.
1. These power supplies have been evaluated to Isolated LPS output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Max.
Input
Output
Output
Voltage
Input Freq
Input
Voltage (V
Output
Power
Model No.
(Vac)
(HZ)
Current (A)
dc)
Current (A)
(W)
LEDWV100-277
50/60
1.2
24
0~4
96
096S024ST-xxx
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wring shall be determined in end product use.
8. These LED drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does
not exceed the maximum output current.
9. These LED drivers are provided with a multi-conductor AWM wire consisted of two (purple and gray) 22 AWG, min 80°C, min
300 V leads for connecting a dimmer to vary the output current. The connecting diagram is shown as below. The leads are
investigated for use in Class 2 output circuit and cannot be interconnected with the other output of these drivers. The dimmer
may be a 0-10 Vdc input voltage or a 0-300 kohm variable resistor.
Vcc
Vcc
Rin
Rin
1-10 V
INPUT (PURPLE )
1-10V
INPUT (PURPLE )
V 1-10Vdc
Rx (0-300 kohm)
GND (GRAY )
GND (GRAY)
or
LED Driver with isolated Class 2 and Non-Class 2 Outputs, Model Series LWx096-0aaSb-YYYYY; where x may be S or P; aa
may be 12, 24, 36, 42, 48, or 52; b may be 1, 2, or 3 as indicated in the Electrical Ratings below; and YYYYY may be any
alphanumeric character or blank for cosmetic features.
1. The LED Drivers have been evaluated to Class 2 and non-Class 2 output requirements for dc circuits.
2. These products are provided with the following electrical ratings:
Model No.
Input Rating
Output type
Voltage Current
(Vac)
(A)
Product
Output is
rated
Voltage
(Vdc)
Maximum Output
Current
(A)
LWx096-012S2
100277
2.2
Constant Current,
Output is Isolated
Class 2
Wet (a)
12
5
LWx096-024S2
100277
2.2
Constant Current,
Output is Isolated
Class 2
Wet (a)
24
4
LWx096-036S2
100277
2.2
Constant Current,
Output is Isolated
Class 2
Damp (b)
36
2.66
LWx096-042S3
100277
2.2
Constant Current,
Output is Isolated
Class 2 for US, and
non-Class 2 for CNR
Damp (b)
42
2.28
January 23, 2014
24
SIGN COMPONENTS MANUAL (SAM)
LWx096-048S3
100277
2.2
Constant Current,
Output is Isolated
Class 2 for US, and
non-Class 2 for CNR
Damp (b)
48
2
LWx096-054S3
100277
2.2
Constant Current,
Output is Isolated
Class 2 for US, and
non-Class 2 for CNR
Damp (b)
54
1.77
LWx096-012S1
100277
2.2
Constant Current,
Output is Isolated
non-Class 2
Damp (c)
12
8
(a) For Models LWx096-0aaS2 (aa is 12, 24), the driver unit (input and enclosure) shall be protected from contact with water by a
suitably rated enclosure material in the end product.
(b) For Models LWx096-036S2 and LWx096-0aaS3 (aa is 42, 48, or 54), the driver unit and output circuitry shall be protected
from contact with water by a suitably rated enclosure material in the end product.
(c) For Model LWx096-012S1, the driver unit and output circuitry shall be protected from contact with water and provided with a
suitable electrical and fire enclosure in the end product.
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end and 101.6
mm (4 in.) from side to side.
4. In the end product, LED Drivers spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. These products shall be enclosed in the end product.
6. These products are suitable for factory wiring only.
7. The suitability of input/output leads and the wiring shall be determined in end product use.
8. These products utilize a UL Recognized (OBJY2), Class 130 (B) electrical insulation system.
9. As part of temperature testing, the case temperature at the temperature reference point, identified as Tc on the case, was
monitored. During the normal temperature test of the end product, the temperature at the temperature reference point is to be
monitored. The absolute value at the temperature reference point cannot exceed 80°C for Models LWx096-012Sb-YYYYY and
o
90 C for Models LWx096-0aaSB-YYYYY; where aa may be 24, 36, 42, 48 and 52. End product to determine suitability if the Tc
is higher during end product evaluation.
10. The LED drivers shall be installed in compliance with the enclosure, mounting, spacing, casualty, and segregation
requirements of the end product application. Electrical/Fire/Mechanical enclosure shall be evaluated in end product.
11. For Models LWx096-0aaS3 (aa is 42, 48, or 54), these products have an output that is rated 42 Vdc or higher. For Canada,
this output cannot be accessible based on maximum voltage restrictions for Class 2 circuits in the Canadian Electrical Code.
The output terminals and circuitry of the end product should be evaluated to confirm compliance with this accessibility
requirement, either based on output terminal design or based on manufacturer specifications for its use in restricted access
areas only. The latter option will require markings on the product as well as the installation manual.
12. The Leakage Current Test was conducted at 277 Vac input with a maximum measurement of 0.6 MIU for Class 2 Models. If
the driver is installed in a cord-connected end product that operates at 120 Vac input, the need for conducting additional leakage
current testing shall be considered in the end product evaluation.
AVA TECHNOLOGY INC
SUITE 6
2640 S MYRTLE AVE
MONROVIA, CA 91016-8210
E332371
LED Module, Designated: US1M-CV Series where M is any 2 to 5 alphanumeric characters (indicates specific model), C is any
one letter (indicates color), and V is 12 or 24 (indicates voltage).
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC or 24VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 1. When units are connected to a Class 2 circuit, their number is to be limited
to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
AVERY DENNISON CORP
250 CHESTER ST
PAINESVILLE, OH 44077
E466002
Polymeric Adhesive System (Laminating Adhesive), designated Cat. Nos. “HPA 1902”, “HPA 1902PET”, “HPA 1905”, and
“HPA 1905PET”.
1. The adhesive system may be used for securement of any combination of surfaces listed in Table A. The end-product operating
temperature is not to exceed the lowest temperature rating of the combination.
2. The adhesive system is suitable where exposed to high humidity and occasional exposure to water. The minimum temperature
rating is - 35°C (-31°F).
3. This adhesive system is suitable for application to smooth flat surfaces, except where another surface configuration is noted.
The adhesive shall be applied in accordance with the manufacturer's instruction. All surfaces shall be clean and dry. The
manufacturer’s instructions regarding cure time shall be followed.
4. The adhesive dynamic bond strength specified in Table A and B includes a safety factor of four.
5. The bond strength values shown in Table A and B were determined in accordance with ASTM D 1002.
25
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
6. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed. The engineer must consider the need to investigate the part for other than the properties investigated, in accordance
with the applicable end-product standard and/or the requirements outlined in UL 746C, Standard for Material Used in Electrical
Equipment Evaluations.
7. The suitability for the use when exposed to oil, chemicals, refrigerant, soap, x-rays, ultraviolet and the like has not been
determined by this investigation, unless otherwise noted.
8. The average as-received bond strength values are as follows. When determining the suitability of the adhesive system in
accordance with item 4, the bond strength value should be based on the lowest average as-received bond strength value of the
material combination.
9. The adhesive static bond strength is 0.25 pounds per square inch, which is the ability to support the dead weight of a sign
panel. Where the total weight of the panel is supported by other mechanical means such as by a flange, lip, or channel, the static
bond strength calculation is not applicable. The minimum square inches of adhesive tape to use is determined by dividing the
maximum static load in pounds by 0.25 pounds per square inch.
10. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts shall
be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the dynamic
bond strength and includes wind loading. The minimum square inches of adhesive tape to use is determined by dividing the
maximum dynamic load in pounds by the adhesive bond strength specified in Table A.
11. After determining the amount of tape required in square inches for the static load and for the dynamic load, the largest number
is the minimum amount of tape that shall be used.
AVL INC
104-94 SANHO-DAERO
GUMI-SI, GYEONGSANGBUK-DO 730-906 REPUBLIC OF KOREA
E347113
LED Module, Model Nos. AVL 3P, AVL 1P, AVL 2P, AVL 3CP, AVL 4P, AVL RGB, AVL-TUBE LIGHTING, AVL 3EC, AVL 4EC,
AVL SPOT LIGHTING BAR, AVL LED LIGHTING BAR, AVL 1WP, AVL 2WP, AVL 3WP, AVL 4WP, AVL 3CSP, AVL 1CAP, AVL
2CAP, AVL 3CAP, AVL 4CAP.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means
Class 2 LED light board, Model No. ALB.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
7. These products cannot be wired in series.
AXIOMLED INC
2663 LEE AVE
SOUTH EL MONTE, CA 91733
E330040
LED Module, Cat. No. AX-LEY Series, where Y can be replaced with any numbers from 1 through 9.
1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. Class 2 LED Modules designated AX-LEY series are each rated max. 7.5 Watts per unit. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Drivers, Models PS144FD24, PS120FD12, PS72FS24, PS60FS12, PS144FD30, PS144HD30, PS144HD24, PS120FD18,
PS120HD18, PS120FD15, PS120HD15, PS120HD12, PS100FD10, PS100HD10, PS80FD5, PS80HD5, PS72FS30, PS72HS30,
PS72HS24, PS60FS18, PS60HS18, PS60FS15, PS60HS15, PS60HS12, PS50FS10, PS50HS10, PS40FS5, PS40HS5.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with maximum of 2 or 1 Class 2
outputs.
2. These power supplies are only suitable for use in indoor and outdoor use applications.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
B EDWARDS & ASSOCIATES LLC
11101 ARROWHEAD DR
GRAFTON, OH 44044
E364797
LED Driver, isolated LPS output, Model ECO 60-12V.
1. These power supplies have been evaluated to Isolated LPS output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
January 23, 2014
26
SIGN COMPONENTS MANUAL (SAM)
Nominal
Nominal Output
Output
Current (A)
Voltage (V dc)
ECO 60-12V
100-240
50/60
1.4
12
5
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wring shall be determined in end product use.
Model No.
Input Voltage
(Vac)
BAYER MATERIALSCIENCE LLC
119 SALISBURY RD
SHEFFIELD, MA 01257
Input Freq
(HZ)
Input Current
(A)
E146154
Rigid sign enclosure system, for use in electric signs, designated: Makrolon Sheet or Makrolon grades GP, SL, OP, LD, PV and
Lumen XT, all may be followed by additional characters.
1. Acceptable for use in dry, damp and wet locations.
2. Acceptable for enclosure, sign body and decorative applications. Enclosure applications include exposed live parts spaced more
than 0.8 mm away from the surface of the material.
3. This material is suitable for direct contact with and mounting to heat producing components such as transformers, power
supplies and ballasts in the end product.
4. Marking required on end product stating, "Replace only with (manufacturer's name of component), type (type designation of sign
face) sign face material".
5. Suitable for use in terminating conduit.
6. Water exclusion must be determined in the end product.
7. Self-threading screws shall not be used to mount components to these materials.
8. The mounting means of components shall be determined in the end-product.
BITRO GROUP INC
201 CHARLES ST
HACKENSACK, NJ 07601
E341583
LED Module, Models OMX-L4, OMX-L3, OMX-M3, OMX-M2, OMX-S2, OMX-N1.
1. These products have been evaluated for connection to a Class 2 power source only, rated 12 Vdc, 60 W max.
2. These products are suitable for use in dry, damp or wet locations.
3. The LED module is provided with leads for interconnection. The suitability of the leads shall be determined in the end product.
LED Module, Class 2 powered LED modules, BT-XXX series designated as “Linear LED Bars”, “PCB Modules”, “Sign Washer”,
“Channel Letter Modules”, “LED Bars” or “Flexible Strips”, where XXX may be any alphanumeric characters. 1. These products
are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 24 Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 powered LED controllers, designated as XXYY-N-Q series, where XX may be SD, BT, LT, or T2; YY may be any
alphabetical characters or blank;, N may be any alphanumeric characters; and Q may be any alphanumeric characters or blank.
1. The input of these products is only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply.
2. These products are provided with dimming connections that have only been evaluated for connection to a Class 2 dimming
circuit.
3. These products are suitable for use in dry and damp locations.
4. These drivers are provided with a maximum of one, Class 2 output.
5. These products are suitable for factory wiring only.
6. These products shall be enclosed in the end product.
BITRO GROUP INC
201 CHARLES ST
HACKENSACK, NJ 07601
E351123
Class 2 LED Power Supply, Model ASU-60-12U, ASU-100-24U.
1. The power supply shall be installed in compliance with the applicable requirements of the end-product standard for, mounting,
spacing, casualty and segregation.
2. The maximum available output parameters were within the maximum allowable limits for Class 2, inherently limited as specified in
the UL 1310, Standard for Class 2 Power Units and also in accordance with the Canadian Safety Standard CSA C22.2 No. 223.
3. The power supply was submitted and tested for a maximum manufacturer's recommended Tc location, should not exceed 69°C,
in ambient of 40°C. If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature
test shall be conducted in the end use product.
4. Power Supply is intended for use in indoor Dry and Damp location only.
5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
any other direction.
6. The input and output leads were not subjected to the strain relief test.
7. The primary (Black-White) and the output (Red-Black) connection wires of the power supply are R/C (AVLV2/AVLV8), 18 AWG,
90ºC. The suitability of the leads shall be determined in the end-use application.
27
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
BLUEVIEW ELEC-OPTIC TECH CO LTD
1000 SECTION 2, 2ND KONGGANG RD
SOUTHWEST AVIATION INDUSTRIAL
DEVELOPMENT ZONE SHUANGLIU
CHENGDU, SICHUAN 610207 CHINA
E318168
LED Lighting Modules, Cat. No. BV-ALUMINUM-PIRANHA Series.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Operating Voltage
( V DC )
12
12
12
12
12
12
12
12
Part No.
BV-Aluminum-Piranha-R
BV-Aluminum- Piranha-Y
BV-Aluminum- Piranha-A
BV-Aluminum- Piranha-WW
BV-Aluminum- Piranha-CW
BV-Aluminum- Piranha-PW
BV-Aluminum- Piranha-G
BV-Aluminum- Piranha-B
Current per
module ( mA )
40
30
30
40
40
40
40
40
Watts per
module ( W )
0.48
0.36
0.36
0.48
0.48
0.48
0.48
0.48
Emitting color
Red
Yellow
Amber
Warm White
Cold White
Pure White
Green
Blue
LED quantity
(pc)
14
14
14
22
22
22
22
22
LED Lighting Modules, Model BV-STRIP-PIRANHA Series.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Operating
Current per
Voltage ( VDC ) module ( mA )
Part No.
Watts per
LED quantity
module ( W ) Emitting color
(pc)
BV-Strip-Piranha-1*3-R
12
40
0.48
Red
BV-Strip-Piranha-1*3-Y
12
30
0.36
Yellow
13
13
BV-Strip-Piranha-1*3-A
12
30
0.36
Amber
13
BV-Strip-Piranha-1*3-WW
12
20
0.24
Warm White
13
BV-Strip-Piranha-1*3-CW
12
20
0.24
Cold White
13
13
BV-Strip-Piranha-1*3-PW
12
20
0.24
Pure White
BV-Strip-Piranha-1*3-G
12
20
0.24
Green
13
BV-Strip-Piranha-1*3-B
12
20
0.24
Blue
13
LED Lighting Modules, BV-Flexibility-X-X Series, where X-X can be any alpha-numeric combination denoting LED color.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Part No.
Operating
Current per
Watts per
Voltage ( V ) module ( mA ) module ( W )
Emitting color
Max. LED quantity
per module (pc)
BV-Flexibility- SMD 1-R
12
100
1.2
Red
15
BV-Flexibility- SMD 1-Y
12
100
1.2
Yellow
15
15
BV-Flexibility- SMD 1-B
12
100
1.2
Blue
BV-Flexibility- SMD 1-G
12
100
1.2
Green
15
BV-Flexibility- SMD 1-W
12
100
1.2
White
15
BV-Flexibility- SMD- 2-R
12
200
2.4
Red
30
BV-Flexibility- SMD- 2-Y
12
200
2.4
Yellow
30
BV-Flexibility- SMD- 2-B
12
200
2.4
Blue
30
BV-Flexibility- SMD- 2-G
12
200
2.4
Green
30
BV-Flexibility- SMD- 2-W
12
200
2.4
White
30
January 23, 2014
28
SIGN COMPONENTS MANUAL (SAM)
LED Lighting Modules, Cat. Nos. BV-POWER-X-0.5W, BV-POWER-X-1W.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Part No.
Operating Voltage
Current per
Watts per
( V DC )
module ( mA ) module ( W ) Emitting color
BV-Power-R-1W
12
350
1.0
Red
LED quantity
(pc)
1
BV-Power-W-0.5W
12
180
0.5
White
1
LED Lighting Modules, Cat. No. BV-S-PY-0.5XX, where S may be replaced with Strip or Square, Y may be replaced with A, C, G
or K and XX may be any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Lighting Modules, Cat. No. BV-A1-X, where X may be replaced with any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 0.72 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
BOCA FLASHER INC
552 NW 77TH ST
BOCA RATON, FL 33487
E221730
LED Channel Letter Sign Kit, Cat. No. CCS100, CCD72, LS1001, LS1002, LS1061, LS1062, CCD36, LSS3001, LSS3061 and
CCD180.
1. These products are only suitable for connection to a UL Listed Class 2, AC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. LEDs connected to a 12 Volt AC Class 2 power source are not required to be enclosed or protected from weather. LEDs
connected to a 24 Volt AC Class 2 power source are limited to installation in a dry or damp location only.
4. Cat. No. CCD72 is rated for 12 watts per unit, Cat. No. CCS100 is rated for 4.8 watts per foot, Cat. No. LS1002 is rated at 6
Watts per foot, Cat. No. LS1001 is rated 3.6 Watts per foot and Cat. No. SM0006 is rated at 0.96 Watts per unit. 5. 5. The total
number of feet of each type and inches for the inch unit are not to produce a total wattage of greater than 60 watts per Class 2
circuit.
6. Models CCS100, LS1001, and LS1002 are provided with a R/C wire connectors on the printed wiring board to increase the
length of channel letters. No other cut across the board is permitted.
Class 2 LED Channel Modules, Cat. No. ACXXXX Series and DLSXXXX Series where XXXX maybe be any numbers from 00009999 and LED modules Color Controllers, Cat. No. SLMCTL, RSBCTL, and CTM.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 Volt or less power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LEDs, “Channel Letter LED” Modules ACXXXX Series and DLSXXXX Series when connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 circuit.
4. These products are suitable for use in dry and damp locations.
LED drivers, Cat. No. MR16_1-5WD-xxx ("1 to 5 LED Driver") where xxx may be replaced with 12A or 24D; LED Disk, Cat. Nos.
5X1WxLB-yyyy ("5 LED Disk"), 3X1WxLB-yyyy ("3 LED Disk") and 1X1WxLB-yyyy ("1 LED Disk") where yyyy may be replaced
with numbers 0 through 9 or letters of alphabet A through Z or combination of letters or numbers; Class 2 HPLS Light Strip, Cat.
No. HPFLSxx-Q\'-24y-zzzz, where Q may be replaced with the number 1, 2 or 3, xx and zzzz may be replaced with letters of
alphabet A through Z or combination of letters or numbers.
1. Class 2 LED Drivers Model LED Drivers, cat. No. MR16_1-5WD-xxx and LED Disk, cat. nos. 5X1WxLB-yyyy, 3X1WxLB-yyyy,
1X1WxLB-yyyy are only suitable for connection to a maximum , max. 15 Volts AC or max. 24 Volts DC or less.
2. Class 2 HPLS Light Strips, cat. no. HPFLSxx-Q'-24y-zzzz are only suitable for connection to a maximum , max. 24 Volts AC or
less.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
4. Class 2 Assemblies, Model LED Drivers, cat. No. MR16_1-5WD-xxx, LED Disk, cat. nos. 5X1WxLB-yyyy, 3X1WxLB-yyyy,
1X1WxLB-yyyy and HPLS Light Strips, cat. no. HPFLSxx-Q'-24y-zzzz is each rated max. 24 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
29
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
5. Class 2 LED Drivers Model LED Drivers, cat. No. MR16_1-5WD-xxx and LED Disk, cat. nos. 5X1WxLB-yyyy, 3X1WxLB-yyyy,
1X1WxLB-yyyy are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less.
6. Class 2 HPLS Light Strips, cat. no. HPFLSxx-Q'-24y-zzzz are suitable for use in dry, damp locations with supply sources rated
at 24 Volt AC.
Class 2 Powered LED Modules, Cat. No. HPLS/HPFB Series (Border Light) and NFLS-HO-XXX Series (Border Light), where
XXX can be replaced with any alphanumeric character.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED modules, HPLS/HPFB Series (Border Light)”, is rated max. 45 Watts per module. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
Class 2 LED modules color controllers, Models SLMCTL, RSBCTL, CTM.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 Volt or less power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These class 2, low voltage, low energy LED module color controllers when connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 circuit.
4. These products are suitable for use in dry and damp locations.
LED flasher Buffer Cards, Cat. No. LSDT33X_24, CCDST50_24, BFPS0001
1. These components are to be installed in accordance with the manufacturer's instructions.
2. These devices are rated as specified below.
Catalog Number
(Input-Output)
Operating Voltage
Max Output Current
(rms)
Type Load
LED
LSDST33X-24
24 V ac
2.5 A
CCXST50_24
24 V ac
2.5 A
LED
BFPS001
24 V ac
2.5 A
LED
3. An electrical enclosure needs to be provided in the end product.
4. No tests have been conducted on these components and as such, end product testing should be considered.
Class 2 Powered LED Modules, Cat. Nos. BF-HPNLS-12A-XXX-QQQ-ZZZZ Series, where XXX and QQQ may be blank or
replaced with alphanumeric characters and ZZZZ may be replaced with any number combinations from 0000 to 9999.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. Class 2 LED modules, Cat. No. BF-HPNLS-12A-XXX-QQQ-ZZZZ Series are each rated max. 14 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Regulator Model HPCCSD.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt dc or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 24 Vdc.
3. These products are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
BRAND W LLC, DBA ECO LIGHT LED
255 DISTRIBUTION DR
UNIT 104
SPARKS, NV 89441
E357471
Class 2 LED Modules, designated as "M Star XXX LED Strip Lights-YYVDC" series, where M may be Ribbon or Digital; XXX may
be blank, Max, Max TPU, Ultra, Ultra Extreme, HID, HID TPU, Supreme, Extreme Outdoor, Extreme RGB Outdoor, Ultra Extreme
Outdoor, RGB, RGB 90, RGB 180, Side or Side Light; and YY may be 12 or 24.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. Ratings to be determined in end use.
BU-CHANG
3RD FL, C BLK, MICRO OFFICE BLDG
554-2 GASAN-DONG
GEUMCHEON-GU, SEOUL REPUBLIC OF KOREA
E330293
Class 2 LED Modules, Designated as "BIGBANG", Models SW-DC-B02, SW-DC-B03.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
January 23, 2014
30
SIGN COMPONENTS MANUAL (SAM)
3. These products are each rated max. 1.2 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
CAO LIGHTING INC
4628 W SKYHAWK DR
WEST JORDAN, UT 84084
E332228
Class 2 LED Modules, designated as LuxemBright LED System, Cat. No. 77X-YYYTT Series; where X may be numerals 0-9;
YYY may be any alphanumeric characters; and TT may be numerals 00 to 99.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated 12 V DC or less.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
CGATE SOLUTIONS LTD
P.O.BOX 3153
HAIFA, 32984
ISRAEL
E351371
Structural panel, designated "ALUMINUM COMPOSITE PANEL", Models ALS02, ALS03, ALS04, and ALS06.
1. This product is intended as an outer decorative covering, has not been investigated for use as an electrical enclosure.
2. Structural panels may be employed as external decorative faces and are acceptable for support of complete electrical
enclosures, plastic faces, and moldings that are reliably secured to the panel.
3. This product is acceptable for use in dry, damp and wet locations
4. The water exclusion must be determined in the end product.
5. Suitable for use in component support applications. When threaded directly into the panels, suitability of screws shall be
determined in the end product.
6. Nuts and bolts must be used when fastening a ballast or transformer weighting more than 7-1/2 lbs (3.4 kg).
7. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
8. These materials are rated Polyethylene. Consideration will need to be given to end product thermal spacings from heat
producing components or temperature test.
9. These materials are available as unpainted aluminum or pre-painted aluminum.
10. This material has not been investigated for the securement of conduit, electrode housings or the like, suitability shall be
determined in the end product.
11. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
CHANNELUME/LET-R-EDGE
4206 MAIN ST
P O BOX 3046
UNION GAP, WA 98903
E55183
Structural Siding, Cat. No. Channelume or Let-R-Edge.
1. The siding shall be bonded at points of conduit connection.
2. When used outdoors, all internal sign components shall be suitable for outdoor use.
Urethane Foam Elastomer Wood Coating, "Channelcoat 2".
1. This material shall not be used to enclose bare live parts or wiring.
2. The coating shall be applied in accordance with the supplied instructions.
3. The coating shall be applied to give a complete and uniform covering over the treated surfaces (0.008 in. minimum thickness).
4. The coating is acceptable for use in lieu of "asphalt-based paint" where required with metal-faced plywood panels.
CIRRUS SYSTEMS INC
1945 FRANCISCO BLVD
SUITE 28
SAN RAFAEL, CA 94901
E352796
LED modules, Models N2-19C, N2-12.7C System.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These products are suitable for use in dry location and damp locations.
3. These products shall be enclosed in a suitable electric enclosure in the end product.
4. These products have the following electrical ratings:
Model
Max Input
Voltage (V)
Max Input
Current (A)
Max Input
Power (W)
Frequency
(Hz)
31
SIGN COMPONENTS MANUAL (SAM)
“LED Module" Model No.
N2-19C
110-240
0.64 A
37.5 W
50/60
“LED Module" Model No.
N2-12.7C
110-240
0.64 A
37.5 W
50/60
January 23, 2014
5. These units were tested in open air room ambient temperature with the fans operating continuously. The need to conduct
temperature test at elevated ambient shall be determined in the end product.
6. The need to conduct ground continuity tests and mold stress test shall be determined in the end product.
CITYLUX (CHINA) LED LIGHTING LTD
RM 2105 WH195 TREND CENTRE
29-31 CHEUNG LEE ST
CHAI WAN, 999077 HONG KONG
E361402
Class 2 LED Module, Models CTL-3528SMD60-LKST, CTL-3528SMD60-LKIC, CTL-3528SMD60-LKOC.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Vdc.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
7. The mounting means shall be determined in end use.
CLEANLIFE ENERGY LLC
8800 BROOKPARK RD
CLEVELAND, OH 44129
E362201
Class 2 LED Modules, CL-CTS Series, may be followed by alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source, rated maximum 12 VDC or 24 VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than the electrical ratings.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 VDC or 24 VDC.
4. These products are not required to be enclosed or protected from the weather in the end product.
COOLEDGE LIGHTING
UNIT 1
3751 NORTH FRASER WAY
BURNABY, BC V5J 5G4 CANADA
E365284
Class 2 LED lightsheet; Model Series LS-Ga-Pb-c-Kd-We-Lf-Sg-Ch-i, where a is any alphanumeric, b is 07 to 12, c is CLF or
DRF, d is any two digit number, e is any number 28 to 280, f is any number 280 to 10850, g is maximum 310, h is 05 to 15, and i is
any alphanumeric or blank.
1. These LED modules have been evaluated for powering only by a Class 2, LPS, or LVLE power source.
2. The need for an enclosure shall be determined in the end use.
3. This construction has been evaluated for dry and damp locations only. Use in an environment other than the above requires
additional evaluation.
4. The suitability of the mounting means shall be determined in the end use.
5. The suitability of the power connection means shall be determined in the end use.
6. The products may be provided with output pads where one lightsheet can “pass through” the input voltage rails to the next
lightsheet in parallel with the first. The total power available from the source powering multiple “pass through” products shall not
exceed Class 2 limits.
LED drivers, isolated Class 2 output, Model PSD-090W-UNV-058VCC.
1. These power supplies have been evaluated to Isolated LPS output requirements or for dc circuits with a maximum of one Class
2 output per US only.
2. These products are provided with the following electrical ratings:
Input Ratings
Vac
Output Ratings
mA
120/230-240/277 1.0/0.54/0.45
Hz
Vdc A (max) W
50-60 58
1.6
90
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in the end product.
5. This driver is considered a Class I (grounded) product. The driver's enclosure shall be properly bonded to ground, such as by
the mounting screws or the like through the openings in the end flanges, in the end-use.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wring shall be determined in end product use.
8. This power supply was provided with dimming circuitry in the secondary. The dimming controls and the LED +/- outputs were
evaluated as Class 2/LVLE/LPS.
Class 2 power supply, Series PSD-yW-UNV-058VCC0020, where y may be a 30, 40 or 50.
1. These power supplies have been evaluated to Class 2 output requirements in the United States for dc circuits with a maximum
of one Class 2 output.
January 23, 2014
32
SIGN COMPONENTS MANUAL (SAM)
2. These power supplies have been evaluated to LPS or LVLE output requirements in Canada for dc circuits with a maximum of
one LPS or LVLE output.
3. These products are provided with the following electrical ratings:
Model
Number
Input Voltage (V) Input Current (A)
Frequency Output Voltage
(Hz)
(Vdc)
Output
Current (A)
W (max)
PSD-50W
120/230-240/277
0.58/0.30/0.25
50/60
58
0.86
50
PSD-40W
120/230-240/277
0.46/0.24/0.20
50/60
58
0.70
40
PSD-30W
120/230-240/277
0.34/0.19/0.15
50/60
58
0.53
30
4. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end-to-end,
and 101.6 mm (4 in.) from side-to-side.
5. These products shall be enclosed in the end product.
6. These products are suitable for factory wiring only.
7. These products are intended for use in dry or damp locations only.
8. The suitability of input/output leads and the wiring shall be determined in end product use.
9. The output circuitry of these units shall be made inaccessible in the end product applications when the units are marked for use
in Canada.
COOLEY INC
50 ESTEN AVE
P O BOX 939
PAWTUCKET RI
E97069
02860
Flexible sign face systems, designated Cooley-Brite, SM-42, Cooley Brite Lite and Cooley-Brite II each with or without suffix
numbers.
Product
Abbreviation
Cooley Brite
CB
Cooley Brite II
CBII
Cooley Brite Lite
CBL
1. Acceptable for us in dry, damp, and wet locations
2. These sign face materials shall comply with the external decorative face requirements of UL 48, particularly the spacings.
3. Limited to decorative applications only.
4. Water exclusion must be determined in the end product.
5. These materials shall not have more than one side surface colored (silk-screened) and shall be mounted only with the uncolored
surface adjacent to lampholders, ballasts and the like.
6. When these materials are used on signs with any dimensions (length or width) in spaces greater than 6 ft, suitable braces
should be employed to prevent the material from billowing and creating short spacings to heat sources.
7. Cooley Brite Lite and SM-42 are manufactured at a thickness of less than 0.5 mm. Testing shall be conducted in the end product
to determine suitability of the tensioning system.
Flexible sign face systems, designated "5M Flexible Backlit Signface" with suffix numbers.
1. The suitability of these materials in combination with Signtech, Inc., Type FH, FC, Signalex Inc., or ABC Sign Products clamps,
to prevent entrance of water in outdoor sign applications, shall be determined.
2. These sign face materials shall comply with the external decorative face requirements of UL 48, particularly the spacings.
3. These materials have not been investigated for use as an electrical enclosure.
4. The suitability of the "fit" of the face material and the "secureness" of the clamp mechanisms of the sign, will be judged in the
end application.
5. These materials shall not have more than one side surface colored (pigmented) and shall be mounted only with the white
surface adjacent to lampholders, ballasts and the like.
6. When these materials are used on signs with any dimensions (length or width) in spaces greater than 6 ft, suitable braces
should be employed to prevent the material from billowing and creating short spacings to heat sources.
7. These flexible sheet materials have been found suitable for use with the Signtech, Inc. (+) tensioning system, the ABC Sign
Products tensioning system (++) or Signalex Inc. tensioning system (+++) below. The combination is suitable for use in sign
applications where Items 1 through 5 (above) have been considered. Mounting and tensioning instructions, which accompany
the following clamps, should be used to ensure proper use of the 5M Flexible Backlit Signface.
Flexible sign face systems, Model designated Reflections XL, may be provided with additional suffixes.
1. Acceptable for us in dry, damp, and wet locations
2. These sign face materials shall comply with the external decorative face requirements of UL 48, particularly the spacings.
3. Limited to decorative applications only.
4. Water exclusion must be determined in the end product.
5. These materials shall not have more than one side surface colored (silk-screened) and shall be mounted only with the uncolored
surface adjacent to lampholders, ballasts and the like.
6. When these materials are used on signs with any dimensions (length or width) in spaces greater than 6 ft, suitable braces
should be employed to prevent the material from billowing and creating short spacings to heat sources.
Flexible sign face systems, Model designated Weathertyte and Weathertyte Lite.
1. Acceptable for use in dry, damp, and wet locations.
2. These sign face materials shall comply with the external decorative face requirements of UL 48, particularly the spacings.
3. Limited to decorative applications only.
4. Water exclusion shall be determined in the end product.
5. When these materials are used on signs with any dimensions (length or width) in spaces greater than 6 ft, suitable braces
should be employed to prevent the material from billowing and creating short spacings to heat sources.
6. “Weathertyte Lite” is manufactured at a thickness of 0.018 in (0.45 mm). Testing shall be conducted in the end product to
determine suitability of the tensioning system.
33
SIGN COMPONENTS MANUAL (SAM)
CORE LIGHTING GROUP INC
2222 COTNER AVE
LOS ANGELES, CA 90064
January 23, 2014
E351540
LED Lighting Modules, Cat. No. LS-X-X Series, where X-X can be any alpha-numeric combination denoting LED color.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, Cat. No. ELB-X-X Series, where X may be replaced with any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 0.72 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Company name or trademark
CPI ADVANCED INC
14708 CENTRAL AVE
CHINO, CA 91710
and series designation.
E334246
LED drivers, Models CPI-12V40, CPI-12V60, CPI-12V100.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class
2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. The suitability of grounding connection shall be determined in the end-use product.
CPI ADVANCED INC, DBA ENABA
14708 CENTRAL AVE
CHINO, CA 91710
E228165
Class 2 LED Modules: Cat. No. CPI XLSW series, where X may be 2, 3 or 4.
1. These products are only suitable for connection to a Class 2 power source rated 15 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
CUSTOM ASSEMBLY SOLUTIONS INC
176 EASY ST
CAROL STREAM, IL 60188
E332257
LED sign box: Model CC221.
1. This product is only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 36 VDC or less.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limited supplies.
3. This product is intended for use with a recessed sign.
4. This product is suitable only for use in a dry location without an additional enclosure.
5. The need for any testing, particularly temperature testing, shall be done with the end-product.
6. This component may be secured to the end-product by any means available.
D & P CUSTOM LIGHTS INC
900 63RD AVE N
PO BOX 90465
NASHVILLE, TN 37209
E338346
Class 2 LED modules: designated as XXX-LED-YYYY series, where XXX and YYYY may be any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
January 23, 2014
34
SIGN COMPONENTS MANUAL (SAM)
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
DAEHAN TRANS CO LTD
#7-11 SONGDO-DONG
YEONSU-GU
INCHEON-SI, 406-840, KOREA
E353449
Sign Accessories, Class 2 LED Modules, STAR C04CW, STAR C04DW, STAR C04NW, STAR C04WW, STAR C04R, STAR
C04G, STAR C04B, STAR C02CW, STAR C02DW, STAR C02NW, STAR C02WW, STAR C02R, STAR C02G, STAR C02B,
STAR C0320CW, STAR C0320DW, STAR C0320WW, STAR C0320R, STAR C0320G, STAR C0320B, STAR C0640CW, STAR
C0640DW, STAR C0640WW, STAR C0640R, STAR C0640G, STAR C0640B, STAR N04CW, STAR N04DW, STAR N04WW,
STAR N04R, STAR N04G, STAR N04B, STAR N04RGB, STAR C01CW, STAR C01DW, STAR C01WW, STAR C01R, STAR
C01G, STAR C01B, STAR C0230CW, STAR C0230DW, STAR C0230WW, STAR C0230R, STAR C0230G, STAR C0230B, STAR
C0340CW, STAR C0340DW, STAR C0340WW, STAR C0340R, STAR C0340G, STAR C0340B, STAR F04CW, STAR F04DW,
STAR F04WW, STAR F04R, STAR F04G, STAR F04B, STAR F02CW, STAR F02DW, STAR F02WW, STAR F02R, STAR F02G,
STAR F02B, STAR N03CW, STAR N03DW, STAR N03NW, STAR N03R, STAR N03G, STAR N03B, STAR L02DW, STAR
L02WW, STAR N02CW, STAR N02DW, STAR N02NW, STAR N02R, STAR N02G, STAR N02B, STAR L165DW, STAR
L165WW, RAINBOW C04, RAINBOW C02.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
DAESANG INC
716 KWACHON OFCTL
1-14 BYULYANG-DONG
KWACHON-SHI
KYUNGKI-DO 427-040, KOREA
E211963
Electroluminescent Inverter, Cat. Nos. CX-2003U
1. These units have been evaluated for use in dry locations only.
2. These units are intended for use with R/C (AVLV2) Style 10505 Appliance Wiring Material in a length no greater than 15 meters
per channel on Inverter model CX-2003U with a 1 amp fuse.
3. Cord connected units are not intended for permanent mounting unless entire unit and cord are mounted within an electrical
enclosure.
4. Surface of units may be exposed to a maximum operating temperature of 80ºC.
5. These units are to be enclosed within a suitable enclosure.
6. The output cable is rated maximum 60 C and is to be protected against physical damage within a suitable enclosure.
7. The output cable is to be protected against exposure to direct sunlight.
DAIKAN CO LTD
3-1-7 SANGENYA-HIGASHI
TAISHO-KU
OSAKA, 551-0002 JAPAN
E330600
Class 2 LED Modules, Model Lumi Letter.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
Class 2 OR LPS LED Channel Letter, Cat. Nos. Lumi Letter, Lumi Letter Skeleton, Lumi Letter mini, Lumi Channel and LED
Metal Channel.
1. These products are only suitable for connection to a Class 2 or LPS power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 or LPS
voltage and energy limited circuit and which is rated greater than 24 V DC.
3. When units are connected to a Class 2 or LPS circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 or LPS supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
Class 2 or LPS LED Channel Letter, Cat. No. LIGHT GUIDE PANEL.1. These products are only suitable for connection to a
Class 2 or LPS power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 or LPS
voltage and energy limited circuit and which is rated greater than 24 V DC.
35
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. When units are connected to a Class 2 or LPS circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 or LPS supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
DAKTRONICS INC
201 DAKTRONICS DR
BROOKINGS, SD 57006
E230358
Gas Price Display Module: Part Nos. DF-2x00-a-b-NA-DI, DF-4x00-a-b-NA-DI, FL-2x00-a-b-NA-DI, and FL-4x00-a-b-NA-DI,
where "x" may be 0 or 3, where "a" is LED digit height in inches (up to 27), where "b" is LED color (R, G, or A), may or may
not be followed by additional alphanumeric characters. Part No. 0A-1356-9aaa, 0A-1478-2aaa, and 0A-1478-9aaa, where 'a'
may be any alphanumeric character.
1. These components are intended to be installed in a sign and shall be reliably mounted in the end-product.
2. Suitable for connection to a 20 A maximum branch circuit.
3. Reserved for future use.
4. Models DF and FL series and Part No. 0A-1478-2aaa are suitable for use in outdoor signs and comply with the Water Exclusion
Test. After installation, the Water Exclusion Test should be conducted on the overall end-product.
5. Part Nos. 0A-1356-9aaa and 0A-1478-9aaa are required to be installed in a suitable electrical and weather enclosure that
protects all sides.
6. These components are provided with conduit knock-outs which are suitable for permanent connection to supply.
7. Models DF and FL series and Part No. 0A-1478-2aaa are provided with drain holes in the bottom of the enclosure. Internal
wiring and other components of the end-product shall not be installed below these openings and the components shall be
installed such that the drain holes are free from obstructions.
8. Any changes or additional components added by the end-product sign manufacturer require consideration of additional testing
(Temperature, Input, etc.).
9a. This electrical enclosure is not suitable as an electrical enclosure for field wiring.
9b. Power supply leads and splices must be routed and secured away from low voltage wiring and uninsulated parts of printed
wiring boards.
10. When installed in a double sided configuration, a minimum of 6 in. shall be provided between the rear of each Part Nos. 0A1356-9aaa and 0A-1478-9aaa module.
LED Digit, Part No. OP-1192-XXXX and OP-1279-xxxx, where X may be 0 thru 9.
1. These products are only suitable for connection to a UL Recognized Daktronics 24 V LED driver.
2. These products have not been evaluated to be suitable as an enclosure.
3. These products are suitable for use in dry or damp locations.
4. These products are required to be enclosed and protected from weather.
5. The LED may be part of the weather enclosure only if the LED is in the same enclosure (Sign body) as the LED module. LED
module may be mounted in a metal panel with holes for the LED to protrude.
LED Digits, Part Nos. OP-1150-XXXX and OP-1230-XXXX, where X may be any number 0 through 9.
1. These products are only suitable for connection to a UL Recognized Daktronics 16 V ac LED driver.
2. These products have not been evaluated to be suitable as an enclosure.
3. These products are suitable for use in dry locations.
4. These products are required to be enclosed and protected from weather.
LED Driver, Part No. OA-1192-XXXX and OA-1279-XXXX, where X may be 0 thru 9..
1. The LED driver is intended for use in signs.
2. The LED driver is to be located in a dry or damp location within an overall metal electrical enclosure designated as suitable for
use in dry, damp, or wet locations, as appropriate.
3. The LED driver is to be mounted on one vertical wall of the enclosure.
4. These products are required to be enclosed and protected from weather.
5. Digits (Daktronics, Part No. OP-1192-XXXX) per driver:
Digit Size
16 Column Driver
8 Column Driver
5 in.
16 digits
8 digits
7 in.
16 digits
8 digits
10 in.
16 digits
8 digits
15 in.
16 digits
8 digits
18 in.
16 digits
8 digits
24 in.
16 digits
8 digits
30 in.
16 digits
8 digits
36 in.
8 digits
4 digits
42 in.
4 digits
2 digits
48 in.
4 digits
2 digits
The outputs of the driver may be wired with Class 2 wiring methods when the driver is installed in the same sign body or housing
as the LED panel.
The drivers, when located remotely, have not been evaluated for Class 2 or LPS wiring methods. Class 1 wiring methods between
the LED driver and LED panel should be used.
LED Drivers, Part Nos. OA-1150-XXXX and OA-1230-XXXX, where X may be any number 0 through 9.
1. The LED driver is intended for use in signs.
2. The LED driver is to be located in an indoor dry location within an overall metal electrical enclosure designated as suitable for
use in dry locations.
3. The LED driver is to be mounted on one vertical wall of the enclosure.
4. These products are required to be enclosed and protected from weather.
5. Digits (Daktronics, Part Nos. OP-1150-XXXX and OA-1230-XXXX) per driver:
January 23, 2014
36
SIGN COMPONENTS MANUAL (SAM)
Digit Size
16 Column
Driver
8 Column
Driver
4 Column
Driver
5 in.
16 digits
8 digits
4 digits
7 in.
16 digits
8 digits
4 digits
10 in.
16 digits
8 digits
4 digits
15 in.
16 digits
8 digits
4 digits
18 in.
16 digits
8 digits
4 digits
24 in.
16 digits
8 digits
4 digits
6. The drivers have not been evaluated for Class 2 or LPS wiring methods. Class 1 wiring methods between the LED driver and
LED panel shall be used.
LED Drivers, Part Nos OA-1279-XXXX, where X may be 0 thru 9.
1. The equipment shall be properly bonded to the main protective earth terminal in the end-product. The terminal block provided is
not suitable for grounding/bonding applications.
2. The terminal blocks and connectors provided are suitable for factory wiring only.
3. A suitable electrical and weather enclosure shall be provided in the end-product.
4. The equipment shall be reliably mounted in the end-product.
5. The equipment shall be mounted vertical with the main opening on the bottom. If the equipment is mounted differently, the
Normal Temperature Test shall be re-conducted.
6. The maximum number of 9 LED strings powered by the LED Driver shall not exceed 1000. One driver provided for each single
face sign.
7. Unless contained in the electrical enclosure of the end-product, Class 1 wiring methods shall be used for all secondary output
circuits.
8. The drivers have not been evaluated for Class 2 or LPS wiring methods. Class 1 wiring methods between the LED driver and
LED's should be used.
9. The drivers are intended for dry or damp locations.
Class 2 LED system: Cat. No. DE 34mm LED Matrix Panel.
1. The component shall be reliably mounted in the end-product.
2. A suitable enclosure (weather, electrical) shall be provided in the end-product.
3. The internal volume of the end-product enclosure shall not be less than 9000 cubic inches.
4. One 100 CFM exhaust fan shall be provided for each power supply in the end-product and each fan shall be wired to operate
100% of the time.
5. A suitable branch circuit protective device not exceeding 20 A shall be provided in the end-product.
LED Time and Temperature Module, Model DF-1011-X-Y, where X is digit height in. inches (10, 13, 18), Y is LED color (R = red,
A = amber), may or may not be followed by additional alphanumeric characters.
1. These components are intended to be installed in a sign and shall be reliably mounted in the end-product.
2. A suitable branch circuit protective device not exceeding 20 A shall be provided in the end-product.
3. A suitable disconnect device shall be provided in the end-product.
4. The front face of the component is suitable for use as an electrical and weather enclosures. After installation, the Water
Exclusion Test should be considered on the overall end-product to verify water does not enter the overall sign behind the
flanges, especially if no gasketing or other equivalent means is provided between the flanges and the end-product enclosure.
5. These components are provided with conduit knock-outs which are suitable for permanent connection to supply.
6. Equipment is provided with drain holes in the bottom of the enclosure. Internal wiring and other components of the end-product
shall not be installed below these openings and the components shall be installed such that the drain holes are free from
obstructions.
7. Any changes or additional components added by the end-product sign manufacturer require consideration of additional testing
(Temperature, Input, etc.).
8. Any splices need to be made in an electrical enclosure outside the equipment.
Gas price display modules, Model DAKT-0208-00, FL-3000@, and FL-4500@ where @ may be replaced by alphanumeric
characters.
1. These components are intended to be installed in a sign and shall be reliably mounted in the end-product.
2. Suitable for connection to a branch circuit not exceeding 20A.
3. Reserved for future use.
4. These signs are suitable for use in outdoor signs and comply with the Water Exclusion Test. After installation, the Water
Exclusion Test should be conducted on the overall end-product.
5. These components are provided with conduit knock-outs which are suitable for permanent connection to supply.
6. These signs are provided with drain holes in the bottom of the enclosure. Internal wiring and other components of the endproduct shall not be installed below these openings and the components shall be installed such that the drain holes are free
from obstructions.
7. Any changes or additional components added by the end-product sign manufacturer require consideration of additional testing
(Temperature, Input, etc.).
DASAN AD CO LTD
DASAN BLDG, 299-79, 2GA
SEONGSU-DONG
SEONGDONG-GU
SEOUL, 133-120 REPUBLIC OF KOREA
E364429
Class 2 LED modules, Model Nos. DS-W6030, DS-W6033, DS-R6030, DS-G6030, DS-B6030, DS-WW6030, DS-W6030u, DSRGB6030, DS-RGB6030u, DS-DFL8030, DS-W6030PL, DS-W6030PLIC, DS-W6030IC, DS-W6030c.
1. These products are only suitable for connection to a voltage and energy limited Class 2 power source rated 12 V DC or less.
37
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. Input and output wires connection shall be as follow:
LED module connections
VCC: (+) 12 Vdc input
GND: (-) Ground
Data and CLK are for color control signal communication and are optional.
GND + data = Sender
GND + CLK = Receiver
Class 2 LED modules, Model Nos. DS-DFL4040, DS-DFL5040, DS-W4040c, DS-W5040c.
1. These products are only suitable for connection to a voltage and energy limited Class 2 power source rated 12 V DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. Input and output wires connection shall be as follow:
LED module connections
VCC: (+) 12 Vdc input
GND: (-) Ground
Data and CLK are for color control signal communication and are optional.
GND + data = Sender
GND + CLK = Receiver
DAWEN INC
8306 NW 68TH ST
MIAMI, FL 33166 USA
E340799
LED Lighting Modules, Cat. No. DW-ALUMINUM-PIRANHA Series.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, Model DW-STRIP-PIRANHA Series.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures
LED Lighting Modules, Models DW-FL-C5050RGB-12-60, DW-FL-C5050R-12-60, DW-FL-C5050Y-12-60, DW-FL-C5050B-1260, DW-FL-C5050G-12-60, DW-FL-C5050W-12-60, DW-FL-C5050WW-12-60, DW-FL-C5050P-12-60, DW-FL-R5050RGB-12-60,
DW-FL-R5050R-12-60, DW-FL-R5050Y-12-60, DW-FL-R5050B-12-60, DW-FL-R5050G-12-60, DW-FL-R5050W-12-60, DW-FLR5050WW-12-60, DW-FL-R5050P-12-60, DW-FL-R5050AMBER-12-60, DW-FL-C3528R-12-60, DW-FL-C3528Y-12-60, DW-FLC3528B-12-60, DW-FL-C3528G-12-60, DW-FL-C3528W-12-60, DW-FL-C3528WW-12-60, DW-FL-R3528R-12-60, DW-FLR3528Y-12-60, DW-FL-R3528B-12-60, DW-FL-R3528G-12-60, DW-FL-R3528W-12-60, DW-FL-R3528WW-12-60, DW-FLR3528AMBER-12-60, DW-FL-R3528W-12-120, DW-FL-R3528WW-12-120.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, Cat. No. DW-S-PY-0.5XX, where S may be replaced with Strip or Square, Y may be replaced with A, C, G
or K and XX may be any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Lighting Modules, Cat. No. DW-A1-X, where X may be replaced with any alphanumeric characters.
January 23, 2014
38
SIGN COMPONENTS MANUAL (SAM)
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 0.72 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
DECORA INDUSTRIES INC DATA DISPLAY SYSTEMS DIV
14001 TOWNSEND RD
PHILADELPHIA, PA 19154
E464648
Class 2 LED modules, designated "IW# 6419-06DD."
1. These products are suitable for use in dry, damp and wet locations when supplied with a Class 2 power source rated 12 Volt DC
or less.
2. Suitable only for connection to a Class 2/LPS circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
DECORS USA LLC
402 MAPLE HILL DR
WOODBRIDGE, NJ 07095
E358503
Class 2, LED Array, Model HCL-077.
1. The LED Array is intended for connection to a 12 VDC Class 2 power source, therefore not required to be enclosed. When the
LED arrays are connected and used with other than Class 2 source of supply, the need for an additional evaluation shall be
considered in the end use product evaluation.
2. The LED Array is suitable for use in dry, damp and wet locations.
3. When used in applications other than signs, additional evaluations shall be considered per end-product application.
4. Suitability of mounting shall be determined in the end-product.
5. Suitability of the connector shall be determined in the end-product.
DELTA ELECTRONICS INC
3 TUNGYUAN RD
CHUNGLI INDUSTRIAL ZONE
TAOYUAN COUNTY 32063 TAIWAN
E303831
LED Class 2 Power Supplies, Models SDMV1260A, SDMV1260GW, SDMV2480A, SDMV2480GW, SDMV2460A, SDMV2420A.
1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp
locations. Models SDMV2480GW and SDMV1260GW are suitable for wet location.
2. These power supply needs to be installed in an enclosure with a means for the connection to conduit.
3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110( C. Similarly, for Model
SDMV2420A, a temperature test is required when installed in an enclosure smaller than 13.5 by 6 by 4 inches, but the maximum
temperature on the output transformer by thermocouple is 90(C.
4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location
LED Class 2 Power Supplies, Model 913710052466 or 913710052467.
1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp
locations.
2. These power supply needs to be installed in an enclosure with a means for the connection to conduit.
3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110( C.
4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location
LED Drivers, Models SDHV24D80GXX, SDHV12D60GXX, where X=A~Z, 0~9 or blank.
1. These LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. These products are provided with the following electrical ratings:
Input Voltage (V
ac)
Input Freq
(HZ)
SDHV24D80GXX
100-277
50/60
1.1
24
3.3
80
SDHV12D60GXX
100-277
50/60
0.85
12
5.0
60
Model No.
Input Current Output Voltage Output Current
Output
(A)
(V dc)
(A)
Power (W)
3. The load powered by the Class 2 output of the LED drivers are suitable for use in dry, damp and wet locations.
4. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
5. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
6. These products shall be enclosed in the end product.
7. The suitability of output leads, rated No. 24 AWG minimum, rated 80°C minimum, 600 V, shall be determined in end product
use.
8. These units may provided with Dimming Input (Purple and Gray wires) to control output current range, the suitability shall be
determined in each end-use application.
9. These products are intended for use in dry and damp locations.
39
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
LED Drivers, Model SDHV24100XX. (Where X can be any alphanumeric or blank).
1. The LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. In the end product, LED Drivers spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
3. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
4. The maximum working voltage present and dielectric voltage withstands test voltage applied between primary circuits and
secondary output/plastic enclosure for each model are tabulated below.
Hi-pot
Hi-pot
Model name
Working Voltage
P-S
P-enclosure
SDHV24100XX
310 Vrms, 504 Vpk
3990 (3000) Vac
3990 (3000) Vac
5. The LED drivers had been considered ambient 60 degree C. If operated at a higher ambient temperature, it should be
determined in end product.
6. The LED drivers are intended for factory installation only.
7. The LED drivers are intended for use in a dry and/or damp location. Other uses shall be considered in end product.
8. The LED drivers shall be installed in compliance with the enclosure, mounting, spacing, casualty, and segregation requirements
of the end product application.
9. The suitability of input and output leads shall be determined in end product.
DGI
SUITE 211
1195 PARK AVE
EMERYVILLE, CA 94608
E345554
Class 2 LED Lighting Modules, DLM####-###.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 24 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry and damp locations with supply sources rated at 24 Volts DC or less.
5. These products are required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
DIODE LED
SUITE 211
1195 PARK AVE
EMERYVILLE, CA 94608
E348276
Class 2 LED Lighting Modules, Cat Nos. DI-0001, DI-0010, DI-0001-L, DI-0001-T, DI-0104, DI-0106, DI-0002, DI-0011, DI-0002L, DI-0002-T, DI-0105, DI-0107, DI-0003, DI-0006, DI-0005, DI-0004, DI-0008, DI-0007, DI-0090, DI-0090-L, DI-0090-T, DI-0012,
DI-0108, DI-0091, DI-0091-L, DI-0091-T, DI-0013, DI-0109, DI-0100, DI-0101, DI-0094, DI-0014, DI-0095, DI-0015, DI-0080, DI0081, DI-0070, DI-0040, DI-0041, DI-0073, DI-0051, DI-0052, DI-0053, DI-0056, DI-0055, DI-0054, DI-0058, DI-0057, DI-0071, DI0160, DI-0161, DI-1101.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
DONGBU LIGHTEC CANADA INC
2700 JOHN ST
MARKHAM, ON L3R 2W4 CANADA
E362079
Class 2 LED, Models LMS12, LMS24, followed by 300, 580, 860, 1140, 1420, CS or SP.
1. These products are only suitable for connection to a Class 2 power source, rated 12 or 24Vdc.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry locations with supply sources rated at 12 or 24Vdc.
5. These products have not been evaluated for use in damp or wet locations.
6. The suitability of supply leads shall be determined in end use.
7. The mounting means shall be determined in end use.
Class 2 LED, Model LLP.
1. These products are only suitable for connection to a Class 2 power source, rated 12 or 24Vdc.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry locations with supply sources rated at 12 or 24Vdc.
5. These products have not been evaluated for use in damp or wet locations.
6. The suitability of supply leads shall be determined in end use.
January 23, 2014
40
SIGN COMPONENTS MANUAL (SAM)
7. The mounting means shall be determined in end use.
DONGBU LIGHTEC CO LTD
739-8 OJEONG-DONG OJEONG-GU
BUCHEON-SI, GYEONGGI-DO 421-170 REPUBLIC OF KOREA
E332576
LED Modules, Models Lumisheet, Lumi Fit (**** X ****), Lumisheet-t, where first set “****” is any number from 80 to 2450, and
second set “****” is any number from 80 to 1250.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. These products are suitable for use in dry and damp locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
7. When provided with more than one input connector, there shall be no interconnection of circuits allowed, and each Class 2
circuit is separately connected to each Class 2 power supply.
8. A minimum spacing of 6.4mm (1/4 inch) shall be maintained between circuits in the assembled lamp panel.
DTS MECHELEC LTD
SUIXING IND BLK
GUANGZHOU ENTERPRISE TECH DEV DISTRICT
1 MINGHUA ST
GUANGZHOU, GUANGDONG 510730 CHINA
E309814
Class 2 LED Modules, Designated "LED Light Assembly Panel”.
1. These components are to be installed in accordance with the manufacturer's instructions.
2. These devices are rated as specified below.
Catalog Number
“LED Light Assembly Panel”
(Input-Output)
Operating Voltage
Type Load
24 V ac, 480 mA
LED
3. An electrical enclosure needs to be provided in the end product.
4. No tests have been conducted on these components and as such, end product testing should be considered.
5. The suitability of input leads and connector needs to be considered in the end product.
6. These panels have only been evaluated for use when connected to a Class 2 power source.
7. These products have not been evaluated for use when connected to power
DYNAPAC ROTATING CO
338 HANSEN AVE
SALT LAKE CITY, UT 84115
E30665
Display rotation units, Models H Series 16 and 20, J Series 25, 36, 64, 80, 100 and 200; JS Series 25, 36, 64, 100 and 200; K
Series 25, 36, 64, 80, 100, 200, 350 and 550.
1. These products are subjected to Input, Starting Motor, Temperature, Dielectric Voltage Withstand, Locked Rotor and Dielectric
Voltage Withstand Test After Locked Rotor Tests. Leakage Current and Mold Stress Tests shall be considered in the product.
2. These components have been judged on the basis of the required spacings in UL 879, the Standard for Electric Sign
Components, which would cover the component itself if submitted for unrestricted Listing.
3. Under maximum loading these units drew only 0.1 Amp at 115 V ac. These units shall not be used beyond these ratings or with DC.
4. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
5. These units are for use in dry and damp locations only.
Display rotation units, Model I Series 16, 25, 36, 64, 80 and 100.
1. These products are subjected to Input, Starting Motor, Temperature, Dielectric Voltage Withstand, Locked Rotor and Dielectric
Voltage Withstand Test After Locked Rotor Tests. Leakage Current and Mold Stress Tests shall be considered in the product.
2. These components have been judged on the basis of the required spacings in UL 879, the Standard for Electric Sign
Components, which would cover the component itself if submitted for unrestricted Listing.
3. These are open type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
Display rotation units, Model L Series 25, 100, 200, 350, 550.
1. These products are subjected to Input, Starting Motor, Temperature, Dielectric Voltage Withstand, Locked Rotor and Dielectric
Voltage Withstand Test After Locked Rotor Tests. Leakage Current and Mold Stress Tests shall be considered in the product.
2. These components have been judged on the basis of the required spacings in UL 879, the Standard for Electric Sign
Components, which would cover the component itself if submitted for unrestricted Listing.
3. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
4. These units are for use in dry and damp locations only.
Display rotation units, Models 1G-2.5, 1G-300, 1G-600. Units for use in electric signs where weather protection and electrical
enclosure are provided, Models 1G-2, 1G-4.
1. These sign rotators are rated for 120 Vac.
2. The maximum weight to be placed on these rotators is 400 lbs. Under full load the current draw is 0.1 Amps.
41
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. A suitable enclosure shall be provided in the end use and the suitability of the bonding means through the mounting means shall
be determined in the end use.
3. These units are for use in dry and damp locations.
4. These units should not be located within 2 inches of other heat producing components unless a temperature test is required in
the end product.
E-LITE TECHNOLOGIES INC
2285 RESERVOIR AVE
TRUMBULL, CT 06611
E175045
Electroluminescent panel base material, designated "E-Lume" and/or "Flatlite" panels.
1. The suitability of this material for use within an electrical sign shall be determined.
2. The suitability of the electrical contacts, with regards to clearance, insulation and lead pull shall be determined in the endproduct.
3. Samples of the lamp material were subjected to the Humidity Conditioning Test in UL 924, with acceptable results.
EASTMAN CHEMICAL CO
BLDG P1
137 REGIONAL PARK DR
KINGSPORT, TN 37664
E319574
Rigid sign face material non-enclosure rated, designated "Sheet manufactured with Tritan GX100 (f1) (Non-White)”.
1. (Non-White colors) Acceptable for use in dry, damp and wet locations.
2. (Non-White colors) Limited to only decorative, sign face, and sign body applications. The rigid sign face non-enclosure rated
material is not suitable for use as an electrical enclosure.
3. Minimum 5 cm (2 in) spacing from heat producing components required.
4. Water exclusion must be determined in the end product.
5. Installation and securement of the material into or onto a sign is required.
Rigid sign face material enclosure rated, designated “Sheet manufactured with Tritan GX100 (f1) (Clear and White Only)”.
1. (Clear and White only) The product has been investigation for use with all light sources and for Dry, Damp, and Wet Location.
2. (Clear and White only) Suitable for enclosure, sign body and decorative applications. Enclosure applications limited to insulated
live parts.
3. Minimum 5 cm (2 in) spacing from heat producing components required.
4. Water exclusion must be determined in the end product.
5. Installation and securement of the material into or onto a sign is required.
6. (White only) Suitable for use in terminating conduit.
EBSCO SIGN GROUP LLC
1400 8TH ST N
CLANTON, AL 35045
E352634
Led array sign, designated "TEKSTAR".
1. The LED changing message signs, covered in this Report is intended to be completely enclosed in a suitable outer sign housing
rated for both weather and electrical enclosure.
2. Suitable only for use in wet locations.
3. The LED sign component is not intended for use in the dwelling application with cord plug connected since the leakage current
measured is 2.8 mA.
EDGE LIGHT INDUSTRY CO LTD
55 BEIMIN RD
SONGJIANG, SHANGHAI 201611 CHINA
E353017
LED Modules, LPS/Class 2 type, Models LED-ALS-12V-1W4-3014T-6-590-96, LED-ALS-24V-1W8-3014T-6-1180-336,
EDGEMAX-LED-ALS-24V-W23C-360-5, AF32A-2900*1050, LED Light Panel, Edgelux, Light Box, Edgemax, AF, LGP, CF, LM,
AF18-1800*1200, AF18-1800*1000.
1. These LED Modules are only intended for use with a LPS or Class 2 output power sources.
2. These LED Modules are suitable for use in dry and damp locations.
3. These LED Modules are not provided with a mounting means. The suitability is to be determined in end product use.
4. The temperature rating of LED board is 105°C min., of supply leads is 90°C min., and of Light Guide Panel is 50°C min. The
suitability is to be determined in end product use.
5. The suitability of supply means shall be determined in end product.
EGL CO INC
100 INDUSTRIAL RD
BERKELEY HEIGHTS, NJ 07922
E346985
LED Arrays, Class 2, Model LEV-1200-XXW, where XX is any numeric digits; Model LEV-600-YYY, where YYY is any alpha
numeric digits to indicate color.1. These products are only suitable for connection to a Class 2 power source, rated 12
Volts DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 30 Volt DC or 15 Volt AC.
3. These Class 2 LED modules are rated as below. When units are connected to a Class 2 circuit, they are not to draw a total
wattage of greater than the secondary or output rating of the Class 2 supply.
Model
No. of LED
ELECTRICAL RATINGS
January 23, 2014
V, DC
MA
LEV-1200-XXW
3
12.0
---LEV-600-YYY
2
12.0
48 max.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
EINSTECK ENTERPRISE LLC
4630 E WASHINGTON BLVD
LOS ANGELES, CA 90040
42
SIGN COMPONENTS MANUAL (SAM)
WATTS
1.2
0.58 Max.
E361431
Class 2 LED Modules, EM01AA, EM02AA, EM03AA, EM02BA, EM03BA, EM13BA, EM01CB, EM02CB, EM13CB, EM03CB,
EM33CB, EM11CB, EM11CA, EM13CA, EM01CA, EM03CA, EM103AA, EM133AA, EM133BA, EM102BA, EM91B, EM92A,
EM92B, EM93A, EM93B.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. For M601C series, three units are consisted one module.
7. The suitability of supply leads shall be determined in end use.
Class 2 powered LED modules, Cat. Nos. EM102, EM120, EM112, EM324, EM225, EM332, EM220, EM326, EM340.
1. This product is only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than electrical ratings.
3. This Class 2 LED module is rated as noted in the electrical ratings tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. This product is suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. This product is not required to be enclosed or protected from the weather in the end product.
6. This product may be secured in place in the end products by any means available.
ELECTRALED INC
SUITE 105
10950 72ND ST N
LARGO, FL 33777
E232462
LED Channel Letter Lighting System, Cat. Nos. Series 12 (ES12-), Series 24 (ES24-) and Series 12 Genesis (EG-12).
1. These LED products are suitable for use in dry, damp, and wet locations
2. These products are only suitable for connection to a Listed Class 2, 12 or 24 V power source; or a R/C Class 2 power supply
covered in the Sign Components manual (SAM) and used within its published conditions of use; or a power supply specifically
covered by this report.
3. These products may be pre-wired with the conductors cut to length per the installation instructions, or the product may be
provided with terminals
4. Printed circuit boards with LED’s are supplied in 2, 4, 6 or 12 in. lengths.
5. ElectraLED LED’s may be powered by R/C (XOKV2) Powertronix Corp. Model AA-036539-D, Class 2 transformer. The
transformer shall be provided with a maximum 5 Amp LISTED fuse on the secondary output prior to the printed circuit boards.
The LEDs must be mounted in a suitable sign body in accordance with UL 48. The transformer shall be mounted in a suitable
electrical enclosure in accordance with UL 48 having a minimum volume of 52.0 cubic inches. In the end-product, a replacement
of fuse marking shall be supplied adjacent to the fuse indicating “Replace with same type and rating of protective device.”
6. Enclosure surface to secure the standoffs for printed wiring boards shall be aluminum or as follows:
7. Standoffs may be secured to acrylic UYMR2 Sign Accessory Rigid Sign Face Material or polycarbonate UYMR2 Sign Accessory
Rigid Sign Face Material using QOQW2, 3M double sided tape designated 4950 provided enclosure has a minimum 30.0 cubic
inches of volume per 12 inches of LED printed circuit boards.
8. These products have not been evaluated for use when not connected to a Class 2 voltage and energy requirements when
installed per the manufactures installation instructions.
LED Channel Letter Lighting System, Cat. Nos. ELED-5 or –6.
1. ElectraLED ELED-5 and ELED-6 are intended for Dry, Damp and Wet Location use only when LED's are connected to a
Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. Wet Location
use meaning no additional electrical enclosure or sign body is required for the LEDs.
2. ElectraLED ELED-5 and ELED-6 are intended for Dry and Damp Locations use only when LED's are connected to a Class 2
circuit operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15
VAC. If the LEDs are connected to a Class 2 circuit operating at a potential greater than under 30V continuous DC, 12.4 V
interrupted at a rate of 10-200Hz DC, or 15 VAC then a Sign Body per UL 48 must be maintained to house the LEDs.
3. ElectraLED ELED-5 and ELED-6 LED's may be powered by a UL Listed or Recognized Component Sign Accessory UYMR2, Class 2, output power source. See Conditions of Use No. 1 and No. 2 above for additional details regarding
enclosure requirements.
4. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limiting requirements.
5. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
6. These products may be prewired and the conductors may be cut to length per the installation instructions provided with the
product or the product may be provided with terminals. Printed circuit boards with LED's may be supplied in 2, 4, 6 or 12 in.
lengths.
43
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
7. Enclosure surface to secure the standoffs for printed wiring boards shall be aluminum or as follows:
7A. Standoffs may be secured to acrylic UYMR2 Sign Accessory Rigid Sign Face Material or polycarbonate UYMR2 Sign
Accessory Rigid Sign Face Material using QOQW2, 3M double sided tape designated 4950 provided enclosure has a
minimum 30.0 cubic inches of volume per 12 inches of LED printed circuit boards.
8. The ELED-5 system may be supplied with a Powertronix Corp. Model AA-036539-D, Class 2 transformer. The transformer
shall be provided with a maximum 5 Amp LISTED fuse on the secondary output prior to the printed circuit boards. The ELED5 system may consist of either: 20 feet maximum of red, yellow or orange LEDs OR 16 feet maximum of white, blue or green
LEDs. The LEDs must be mounted in a suitable sign body in accordance with UL 48 when the ELED-5 system with the
Powertronix Corp. Model AA-036539-D transformer and 5 A fuse as described above is utilized. The transformer shall be
mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 52.0 cubic inches. If used
outdoors, the transformer must be mounted in an outdoor electrical enclosure per UL 48 having a minimum volume of 52.0
cubic inches. In the end-product, a replacement of fuse marking shall be supplied adjacent to the fuse indicating “Replace
with same type and rating of protective device.”
9. The ELED-6 system may be supplied with a Lightech Model LET-60, Class 2 transformer. The loading of the transformer shall
not exceed 5.0 amps. The ELED-6 system may consist of either: 20 feet maximum of red, yellow or orange LEDs OR 16 feet
maximum of white, blue or green LEDs.
9A. The Lightech Model LET-60 transformer shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a
minimum volume of 117.0 cubic inches or larger for every four power supplies. If more than four utilized then the enclosure
shall be proportionately increased. If used outdoors, the transformer must be mounted in an outdoor electrical enclosure per
UL 48 having a minimum volume of 117.0 cubic inches or
9B. Secondary wiring must be marked CL2 OR CL3 in accordance with Article 725 of the NEC. Class 1 wiring methods must be
maintained within the enclosure when intermixing Class 2 secondary with primary wiring. Class 2 cable shall be insulated and
marked having the same voltage rating or better as the primary wiring. If cable is not marked with the insulation voltage, then
primary conductors and secondary cable must be permanently positioned to maintain at least 1/4 in. spacing between circuits
or a physical barrier is provided to maintain separation of circuits.
9C. Secondary cable must be protected by rubber grommet when extending through an enclosure. Also, Class 2 cable must be
long enough to extend into channel letter enclosure. Splicing shall only be done within channel letter or enclosure.
LED Channel Letter Lighting System, Cat. Nos. ElectraLED FLEX™ Series. Model ED12- followed by -RD, -RO, -AM, -TG, -VG,
-BG, -BL, -WW or –CW.
TM
1. ElectraLED FLEX LEDs are intended for Dry, Damp and Wet Location use only when LED's are connected to a Class 2
circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. Wet Location use
meaning no additional electrical enclosure or sign body is required for the LEDs.
TM
2. ElectraLED FLEX LEDs are intended for Dry and Damp Locations use only when LED's are connected to a Class 2 circuit
operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. If the
LEDs are connected to a Class 2 circuit operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a
rate of 10-200Hz DC, or 15 VAC then a Sign Body per UL 48 must be maintained to house the LEDs.
TM
3. ElectraLED FLEX LED's may be powered by a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2,
output power source. See Conditions of Use No. 1 and No. 2 above for additional details regarding enclosure requirements.
TM
4. ElectraLED FLEX LED's were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2,
TM
Class 2, 12 V source. The ElectraLED FLEX module draws 0.317 amps, 3.66 Watts per individual module when supplied by
TM
12 V. If the ElectraLED FLEX module is supplied by any other voltage an input test must be conducted in the end-product to
ensure the products do not draw a total wattage greater than the secondary or output rating of the Class 2 power supply
involved.
5. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
6. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
7. These products are prewired and the conductors may be cut to length per the installation instructions provided with the
product.
TM
8. ElectraLED FLEX LED's may be powered by Powertronix Corp. Model AA-036539-D, Class 2 transformer. The transformer
shall be provided with a maximum 5 Amp LISTED fuse on the secondary output prior to the printed circuit boards. The LEDs
must be mounted in a suitable sign body in accordance with UL 48. The transformer shall be mounted in a suitable electrical
enclosure in accordance with UL 48 having a minimum volume of 52.0 cubic inches. In the end-product, a replacement of fuse
marking shall be supplied adjacent to the fuse indicating “Replace with same type and rating of protective device.”
TM
9. The ElectraLED FLEX LED's may be supplied by a Lightech Model LET-60, Class 2 transformer. The LET-60 transformer
shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 117.0 cubic inches
or larger for every four power supplies. If more than four power supplies are utilized then the enclosure shall be proportionately
increased. If used outdoors, the transformer must be mounted in an outdoor electrical enclosure per UL 48 having a minimum
volume of 117.0 cubic inches or larger for every four power supplies. If more than four power supplies are utilized then the
enclosure shall be proportionately increased.
LED Channel Letter Lighting System, Cat. Nos. ElectraLED FLEX™ Series. Model MiniFlex Series Cat. Nos. EM12 followed by
an additional suffix denoting the color of the LED's.
1. These products are only suitable for connection to a UL Listed Class 2, 12 Volt AC or DC power source, or any R/C Class 2,
12 Volt AC or DC power source listed in the SAM, that complies with the stated conditions.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. This Class 2 product, when connected to a Class 2 circuit, shall not draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
ELECTRO-LUMINX LIGHTING CORP
1320 NORTH BLVD
RICHMOND, VA 23230
E319670
January 23, 2014
44
SIGN COMPONENTS MANUAL (SAM)
Electroluminescent Lamps Panels & Tapes, Models Designated as EL Lighttape® Strip and EL Lighttape® Panel.
1. These EL Panels are suitable only for use in portable sign products since the enclosure material is rated V2.
3. Only the Input, Normal Temperature, Dielectric Voltage Withstand Tests and the Current Measurement followed by the Dielectric
Voltage Withstand Tests were conducted.
4. The wiring connection and mounting means were not evaluated and should be considered in the product.
5. The Strain Relief Test was not conducted and needs to be conducted In the end product.
6. This product needs to be enclosed In the end product.
Electroluminescent Drivers, Models SD-8000, SD-4000, SD-2000, SD-1000, SD-400, SD-150 and SD-50.
1. These power supplies have an output that is other than Class 2 such that components connected to the output of these power
supplies needs to be enclosed in the end product.
2. These power supplies are only suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. These power supplies are rated as the following:
Input
Output Maximum
Model
V
Hz
A
Vac
Current, A
SD-8000
120/240
50/60
3.50/1.83
320
3.30
SD-4000
120/240
50/60
2.50/1.27
320
2.10
SD-2000
120/230
50/60
1.02/0.56
320
0.97
SD-1000
120/230
50/60
0.45/0.27
320
0.43
SD-400
120/230
50/60
0.14/0.08
320
0.18
SD-150
120/240
50/60
0.39/0.18
400
0.067
SD-50
120/240
50/60
0.54/0.33
400
0.067
ELECTRONIC DISPLAYS INC
135 S CHURCH ST
ADDISON, IL 60101
E356192
Class 2 LED Signs, Models DSAS, SSAS, DSSAS, SSSAS, DSLS, DSRR.
1. These LED Modules are only intended for use with a LPS or Class 2 output power sources.
2. These LED Modules are suitable for use in dry locations.
3. The suitability of supply means shall be determined in end product.
ELEMENTAL LED LLC
SUITE 211
1195 PARK AVE
EMERYVILLE, CA 94608
E348280
LED Lighting Modules, Cat. Nos. EL-IMGRIB12V-WW, EL-IMGRIB12VSP-WW, EL-BULK100FLEX-WW, EL-BVWHT-WW, ELBVWHTSP-WW, EL-STDL-WW, EL-STDT-WW, EL-IMGRIB12V-NW, EL-IMGRIB12VSP-NW , EL-BULK100FLEX-NW, ELBVWHT-NW, EL-BVWHTSP-NW, EL-STDL-NW, EL-STDT-NW, EL-BVRIB12V-R, EL-BVRIB12VSP-R, EL-BVRIB12V-A, ELBVRIB12VSP-A, EL-BVRIB12V-B, EL-BVRIB12VSP-B, EL-BVRIB12V-G, EL-BVRIB12VSP-G, EL-BVRIB12V-PK, ELBVRIB12VSP-PK, EL-BVRIB12V-PR, EL-BVRIB12VSP-PR, EL-ANRIB12VUV2, EL-ANRIB12VSP-UV2, EL-ANRIB12VIR, ELANRIB12VSP-IR, EL-HDSTRP-WW, EL-HDSTRPSP-WW, EL-BULK100HD-WW, EL-BVWHTHD-WW, EL-BVWHTHDSP-WW,
EL-HDL-WW, EL-HDT-WW, EL-HDSTRP-NW, EL-HDSTRPSP-NW, EL-BULK100HD-NW, EL-BVWHTHD-NW, EL-BVWHTHDSPNW, EL-HDL-NW, EL-HDT-NW, EL-HDSTRP-R, EL-HDSTRPSP-R, EL-HDSTRP-A, EL-HDSTRPSP-A, EL-HDSTRP-B, ELHDSTRPSP-B, EL-HDSTRP-G, EL-HDSTRPSP-G, EL-HDSTRP-PK, EL-HDSTRPSP-PK, EL-HDSTRP-PR, EL-HDSTRPSP-PR,
EL-ANHDRIB12V-UV2, EL-ANHDRIB12VSP-UV2, EL-ANHDRIB12V-IR, EL-ANHDRIB12VSP-IR, EL-IMGBRTRIB12V-WW, ELIMGBRTRIB12VSP-WW, EL-IMGBRTRIB12V-NW, EL-IMGBRTRIB12VSP-NW, EL-HDBRTR12V-WW, EL-HDBRTR12VSP-WW,
EL-HDBRTR12V-NW, EL-HDBRTR12VSP-NW, EL-IMGSDRIB12V-WW, EL-IMGSDRIB12VSP-WW, EL-IMGSDRIB12V-NW, ELIMGSDRIB12VSP-NW, EL-IMGSDRIB12V-R, EL-IMGSDRIB12VSP-R, EL-IMGSDRIB12V-A, EL-IMGSDRIB12VSP-A, ELIMGSDRIB12V-B, EL-IMGSDRIB12VSP-B, EL-IMGSDRIB12V-G, EL-IMGSDRIB12VSP-G, EL-IMGSDRIB12V-PR, ELIMGSDRIB12VSP-PR, EL-9FLX-WW, EL-9FLXSP-WW, EL-9FLX-NW, EL-9FLXSP-NW, EL-BVRGBRIB12V, ELBVRGBRIB12VSP, EL-10FTRGBSP, EL-5FTRGBSP, EL-HDRGB, EL-HDRGBSP, EL-10FTHDRGBSP, EL-5FTHDRGBSP, ELIMGWPRIB12V-WW, EL-IMGWPRIB12VSP-WW, EL-IMGWPRIB12V-NW, EL-IMGWPRIB12VSP-NW, EL-IMGWPRIB12V-R, ELIMGWPRIB12VSP-R, EL-IMGWPRIB12V-A, EL-IMGWPRIB12VSP-A, EL-IMGWPRIB12V-B, EL-IMGWPRIB12VSP-B, ELIMGWPRIB12V-G, EL-IMGWPRIB12VSP-G, EL-IMGWPRIB12V-PK, EL-IMGWPRIB12VSP-PK, EL-IMGWPRIB12V-PR, ELIMGWPRIB12VSP-PR, EL-IMGWPRIB12V-UV, EL-IMGWPRIB12VSP-UV, EL-IMGWPRIB12V-IR, EL-IMGWPRIB12VSP-IR, ELIMGBRTWPRIB12V-NW, EL-IMGBRTWPRIB12VSP-NW, EL-IMGBRTWPRIB12V-WW, EL-IMGBRTWPRIB12VSP-WW, ELIMGWPRGBRIB12V, EL-IMGWPRGBRIB12VSP, EL-HDWPRGB, EL-HDWPRGBSP, EL-HDWPSTRP-WW, EL-HDWPSTRPSPWW, EL-HDWPSTRP-NW, EL-HDWPSTRPSP-NW, EL-WBSTRP, EL-BVWHT2HD-WW, EL-BVWHT2HDSP-WW, ELBVWHT2HD-NW, EL-BVWHT2HDSP-NW.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
ENHANCE NEON TECH (SHANGHAI) CO LTD
5 XIN SONG RD
SHI HU DANG TOWN
SONG JIANG, SHANGHAI 201604 CHINA
E237417
45
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
Electrode Splice Insulator, Model EB-013
1. These devices are rated 150°C, 60 mA, 7500 Vac to ground. May be used with 15K mid-point grounded transformer.
2. These products are suitable for use in dry or damp locations.
3. These products are required to be enclosed or protected from the weather.
4. These products are only for use in Listed signs and Sections of signs. They are not suitable for field installed skeletal neon or
outline lighting.
5. These products are only for use with Listed Transco’s rated 150°C integral sleeve GTO-10 and GTO-15 Cables for 14 AWG to
18 AWG covered in File E226224. For use in accordance with manufacturer's instructions.
ENSEICOM SIGNS INC
225 NORMAN
LACHINE, QC H8R 1A3 CANADA
E347915
LED Array, Model L-1000-LED-01, L-1000-LED-02.
1. These devices shall be mounted in equipment which provides a suitable overall enclosure.
2. These products are only suitable for connection to a Class 2 or LPS power source, rated 24 Volt DC or less.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy requirements.
4. These products are suitable for use in dry and damp locations.
ESPEN TECHNOLOGY INC
12257 FLORENCE AVE
SANTA FE SPRINGS, CA 90670
E364680
LED Drivers, VEV8024MVH-YY, VEV8024MVHDA-10V-YY, VEV6012MVH-YY, VEV6012MVHDA-10V-YY. (Where YY=00-99).
1. These LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. These products are provided with the following electrical ratings:
Input Voltage
(V ac)
Input Freq
(HZ)
VEV8024MVH-YY,
VEV8024MVHDA-10V-YY
100-277
50/60
1.1
VEV6012MVH-YY,
VEV6012MVHDA-10V-YY
100-277
50/60
0.85
Model No.
Input Current
Output
(A)
Voltage (V dc)
Output
Current (A)
Output
Power (W)
24
3.3
80
12
5.0
60
3. The load powered by the Class 2 output of the LED drivers are suitable for use in dry, damp and wet locations.
4. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
5. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
6. These products shall be enclosed in the end product.
7. The suitability of output leads, rated No. 24 AWG minimum, rated 80°C minimum, 600 V, shall be determined in end product
use.
8. These units may be provided with Dimming Input (Purple and Gray wires) to control output current range, the suitability shall be
determined in each end-use application.
9. These products are intended for use in dry and damp locations.
LED Drivers, Model VEV10024MVH-YY (where YY=00-99).
1. The LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. In the end product, LED Drivers spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
3. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
4. The maximum working voltage present and dielectric voltage withstands test voltage applied between primary circuits and
secondary output/plastic enclosure for each model are tabulated below.
Hi-pot
Hi-pot
Model name
Working Voltage
P-S
P-enclosure
VEV10024MVH-YY
310 Vrms, 504 Vpk
3990 (3000) Vac
3990 (3000) Vac
5. The LED drivers had been considered ambient 60 degree C. If operated at a higher ambient temperature, it should be
determined in end product.
6. The LED drivers are intended for factory installation only.
7. The LED drivers are intended for use in a dry and/or damp location. Other uses shall be considered in end product.
8. The LED drivers shall be installed in compliance with the enclosure, mounting, spacing, casualty, and segregation requirements
of the end product application.
9. The suitability of input and output leads shall be determined in end product.
ESTRAKON INC
3924 VARSITY DR
ANN ARBOR, MI 48108
E352383
Class 2 Powered LED Illuminated Sign, designated as "LED Beer Sign".
1. These products are only suitable for connection to a Class 2 power source rated 30 Volt DC or less.
2. These Class powered products are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
3. These products are suitable for use in dry locations with supply sources rated at 30 Volts DC or less.
January 23, 2014
46
SIGN COMPONENTS MANUAL (SAM)
EUROCOM-INC
SUITE 202
8411 STERLING ST
IRVING, TX 75063
E342497
LED Modules, Model Nos. SL-CL-420, SL-IP-CL-420, SL-HI-500, SL-HI-500RGB, SL-IP-HI-500, SL-IP-HI-500RGB, FK-IP-02, FKIP-03, FK-IP-04. All models may be followed by additional suffixes for color temperature.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
EVERBRITE ELECTRONICS INC
720 W CHERRY ST
CHANUTE, KS 66720
E325903
LED Modules, Class 2 LED Modules designated as “Current Limited LED Assembly” series, XXX-YYYY, where XXX may be any
combination of numeric characters from 000 to 999; YYYY may be any combinations of alphanumeric characters from 0000 to
9999 or AAAA to ZZZZ; or suffix XXX-YYYYY , where XXX and YYYYY can be any alphanumeric characters.
1. LED modules designated as “Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY are only suitable for
connection to a Class 2 power source rated max 60 Volt DC or less when used indoors.
2. LED modules designated “Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY are only suitable for connection to
a Class 2 power source rated max 30 Volt DC or less when used outdoors.
3. LED modules designated as “Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY have not been evaluated for
use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated
greater than 60 V DC for indoor use.
4. LED modules designated as “Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY have not been evaluated for
use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated
greater than 30 V DC for outdoor use.
5. LED modules designated as ”Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY are each rated max. 90 watts
per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
6. LED modules designated as “Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY are suitable for use only in dry
locations with supply sources rated at max. 60 Volts DC or less.
7. LED modules designated as “Current Limited LED Assembly” series, XXX-YYYY or XXX-YYYYY are suitable for use in dry,
damp and wet locations with supply sources rated at 30 Volts DC or less
8. These products may be secured in place in the end product by any means available.
9. When these products are used in applications other than signs or Outline lighting, the need to conduct a temperature test shall
be considered.
10. These Class 2 LED modules are only suitable for use in Canada, when marked with Class 2 input voltage ratings 42.4 Vdc or
less for use in dry and damp locations, or rated 30 Vdc or less for wet locations.
EVERBRITE LLC
4949 S 110TH ST
PO BOX 20020
GREENFIELD, WI 53220
E131602
LED Modules, designated as Indoor Passively current limited (resistive) series, XXXXXXXX, where XXXXXXXX may be any
combination of alpha characters.
1. These products are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 60 V DC.
3. These products are each rated max. 60 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. LED modules are suitable for use only in dry and damp locations with supply sources rated at min. 30 Volts DC to max. 60 Volts DC.
5. LED modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
8. LED modules rated for Class 2 input voltage of more than 42.4 V DC are only suitable for use in the United States.
Neon "Animotion" controller, Cat. Nos. 800-0066, -0067 and -0068.
1. The Neon "Animotion" Controller shall be used within the ratings indicated above. Its input shall be powered by the Class 2
output of Model 800-0128 with the controller's output powering the input of Series "NuAUX" auxillary transformers or the
controller's input shall be powered by a Listed Class II high-frequency power supply.
2. The controller has been evaluated at maximum marked ratings with Neon Power Supply Cat. No. 1212 and Cat. No. 800-0065
auxiliary transformer.
3. The number of outputs on the controller may vary between one and eight.
4. No more than four outputs, with a maximum of two outputs per input, may be operated continuously.
5. All eight outputs shall not be on concurrently.
47
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
6. The controllers are intended for Indoor Use Electric Signs or shall be mounted in suitable enclosure when used with Outdoor
Use Electric Signs.
LED Modules, Sequencer Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXXYYYYY may be any combination of alpha characters).
1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2
circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each module is rated and suitable for a maximum of 90 watts.
4. Sequencer modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less.
5. Sequencer modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These modules should be secured by suitable means when installed in the end-use application.
7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
8. When the Sequencer modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these
application are only suitable for use in the United States.
LED Modules, Regulator Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXXYYYYY may be any combination of alpha characters)
1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2
circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each module is rated and suitable for a maximum of 90 watts.
4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less.
5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These modules should be secured by suitable means when installed in the end-use application.
7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these
application are only suitable for use in the United States.
LCD Module, Model LCD v6.x with Power Supply.
1. These LCD modules are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These LCD modules have not been evaluated for use and connection to a power supply source with parameters that exceed
Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each LCD module is rated and suitable for a Class 2 maximum 12 Vdc output of 43 watts.
4. The Exclusion of Water Test may be waived for this LCD module subassembly only when installed in outdoor location signs with
Listed conduit and (QCRV) liquid tight conduit fittings on primary circuits.
5. These modules should be secured by suitable means when installed in the end-use application.
6. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
LED Modules, Cat. No. LCD v6.x with Power Supply.
1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2
circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be
required.
3. Each module is rated and suitable for a maximum of 90 watts.
4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less.
5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
6. These modules should be secured by suitable means when installed in the end-use application.
7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require
additional evaluation.
8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these
application are only suitable for use in the United States.
EVERYLITE LLC
SUITE 208
BLDG B
380 SEMORAN COMMERCE PL
APOPKA, FL 32703
E360604
LED Modules, Models CST-2D-B, CST-2D-G, CST-2D-R, CST-2D-RGB, CST-2D-W, CST-3D-A, CST-3D-B, CST-3D-G, CST-3DR, CST-3D-RGB, CST-3D-W, CST-3D-WW, CST-4D-B, CST-4D-G, CST-4D-R, CST-4D-RGB, CST-4D-W.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
EXCELLART SIGN PRODUCTS LLC
E152309
January 23, 2014
48
SIGN COMPONENTS MANUAL (SAM)
1654 S. LONE ELM RD
OLATHE KS 66061
Frame system, Series EC(+) followed by -4, -4R, -6, -6R, -7, -7R, -8, -8R, -9, -9R, -12 Hinged and Standard, -D/F Hinged and
Standard, -IDS, -S/F Hinged and Standard, or EC-S/F Access System. Accessories for use with EC frame systems, frame, angle,
hat section, 6 in. radius corner, 9 in. radius corner, Cat. Nos. EC-4, -7, -8, EC-IDS, EC-Xtra, FF, FF-2, H-1, H-1.5, LC, LF, RR, or
RRC retainers, Cat. No. EC-12 frame retainer brace, Cat. No. EC-S/F access system, Cat. No. EC lamp raceway, Cat. No. EC
raceway cover, Cat. No. EC lamp/ballast track, Cat. No. EC-IDS raceway, Cat. No. EC Flex System for standard frame, hinged
frame, or retro fit, Cat. No. EC-T1, -T2 trim caps, or Cat. No. 1 1/2, 2 1/2, or H divider bars. Cat. Nos. F retainer, F hinged retainer,
FF short retainer, EC-3.25 radius post, EC-3.25 rectangular post, EC-revel connector, EC-3.25 bleed frame, EC-8 in. radius
quarter end, EC channel letter front, EC channel letter back, EC channel letter lid.
Frame system Excellart (++) followed by C, C-2, M-C, or MC-R, for use with retainers MC- Alternate M-C, ZF.188, ZF.250, ZF-1
1/2, ZF-2, ZFC2 1/2, or ZFC-3. Frame system Narrowline, Cat. Nos. EC-4RN frame, EC-4N frame, 1 in. radius corner connector
and cap.
(+) Frames, angles, and hat sections have the same catalog number as the frame system. Frames available in standard or hinged
versions.
(++) Frames available in smooth or ribbed versions.
Expanda Frame Model AMB13920. Lamp Socket Raceway and Cover Models AMB990 and AMB991.
1. When installed in an outdoor wet location application, consideration shall be given to conducting the water exclusion test of UL
48.
2. The suitability of the components to serve as wireways and electrical enclosures shall be determined in the end use.
3. When installed in an outdoor wet location, the bottom of the cabinet system shall be provided with at least two drain holes in
each inside recess, except for the wireway.
FANTASTIC DISPLAYS INC
2049 S BAKER AVE
ONTARIO, CA 91761
E362917
Class 2 powered LED modules, Cat. Nos. LMYX 225 [+], LMYX 324 [+], LMYX 220 [+], LMYX 332 [+], LMYX 340 [+], LMYX 326
[+], LMYX 341 [+], LMYX 112 [+], LMYX 120 [+], LMYX 102 [+], LMYX 117 [+].
1. This product is only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than electrical ratings.
3. This Class 2 LED module is rated as noted in the electrical ratings tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. This product is suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. This product is not required to be enclosed or protected from the weather in the end product.
6. This product may be secured in place in the end products by any means available.
FEDERAL HEATH SIGN CO. LLC
4602 NORTH AVE
OCEANSIDE, CA 92056
E125271
Sign face tensioning systems, designated "KLICK-RAIL".
1. Water exclusion must be determined in the end product.
2. Any frame dimension greater than 1.8m (6 feet) needs to be braced to prevent billowing.
3. This system limited to only decorative applications, and together with the flexible face material shall comply with the external
decorative face requirements of UL 48, particularly the clearances from heat-generating components to decorative plastic
panels.
4. The suitability of secureness of the clamp and flexible material shall be judged in the end-use application.
5. The installation of this system in a sign shall conform with the instructions provided with this tensioning system.
Class 2 Powered LED Modules, designated RVI Series.
1. These products are only suitable for connection to a UL Listed or UL Recognized Class 2, DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, RVI Series is rated 20 W per 2.7 m length with yellow LEDs and 21 W per 2.7 m length with Red
LEDs. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply and 60 W per Class 2 circuit.
4. These products are suitable for use in dry, damp locations. When the Class 2 output is 12 V or under, these products are
suitable for wet locations.
5. These products are not required to be enclosed or protected from weather.
Controller boards, Models PCB64PD, PCB32PD, PCB06PD.
1. The controller and drivers covered by this report are suitable for damp and dry locations only.
2. The controller Models PCB64PD, PCB32PD, and PCB06PD are suitable for use on a 120 V, 60 Hz service and are capable of
switching up to 64, 32, and 6 points, respectively. They are for use only with triac driver Models PCB20T6, PCB10T12, and
PCB10T4.
3. The Model PCB20T6, 6 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum
load of 13 A, 1560 W.
4. The Model PCB12T10, 12 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a
maximum load of 6.5 A, 780 W.
5. The Model PCB10T4, 4 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum
load of 6.5 A, 780 W.
6. The controller and drivers are intended to mounted on standoffs proving at least 1/2 in clearance between circuit boards and
back of enclosure, within an aluminum enclosure of at least 0.020 inches thick, and an overall dimension provided with forced air
ventilation as specified below.
49
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
7. The controller and drivers are intended to be mounted within an aluminum enclosure mounted in a vertical orientation having a
minimum overall dimension that provides at least 4 inches from the unit to the top and side walls and 4 inches to other heat
producing components and at least 2 inches clearance from printed wiring board mounted components and the enclosure cover.
8. The minimum cooling fan flow rate per driver board shall be lat least 200 CFM.
9. The diameter of the fan opening and exhaust ventilation opening shall be at least the diameter of the fan blades. For each inlet
fan opening there shall be an equivalent exhaust opening. Each opening is to be covered by louvers or other equivalent
guarding to provide opening that comply with end product requirements.
10. The mounting of the controller and drivers and wiring between the controller and driver boards are to be factory assembled.
Primary wiring to the controllers and output wiring to the loads from the driver boards can be made in the factory or field.
Driver boards, Models PCB10T4, PCB10T12, PCB20T6.
1. The controller and drivers covered by this report are suitable for damp and dry locations only.
2. The controller Models PCB64PD, PCB32PD, and PCB06PD are suitable for use on a 120 V, 60 Hz service and are capable of
switching up to 64, 32, and 6 points, respectively. They are for use only with triac driver Models PCB20T6, PCB10T12, and
PCB10T4.
3. The Model PCB20T6, 6 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum
load of 13 A, 1560 W.
4. The Model PCB12T10, 12 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a
maximum load of 6.5 A, 780 W.
5. The Model PCB10T4, 4 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum
load of 6.5 A, 780 W.
6. The controller and drivers are intended to mounted on standoffs proving at least 1/2 in clearance between circuit boards and
back of enclosure, within an aluminum enclosure of at least 0.020 inches thick, and an overall dimension provided with forced air
ventilation as specified below.
7. The controller and drivers are intended to be mounted within an aluminum enclosure mounted in a vertical orientation having a
minimum overall dimension that provides at least 4 inches from the unit to the top and side walls and 4 inches to other heat
producing components and at least 2 inches clearance from printed wiring board mounted components and the enclosure cover.
8. The minimum cooling fan flow rate per driver board shall be lat least 200 CFM.
9. The diameter of the fan opening and exhaust ventilation opening shall be at least the diameter of the fan blades. For each inlet
fan opening there shall be an equivalent exhaust opening. Each opening is to be covered by louvers or other equivalent
guarding to provide opening that comply with end product requirements.
10. The mounting of the controller and drivers and wiring between the controller and driver boards are to be factory assembled.
Primary wiring to the controllers and output wiring to the loads from the driver boards can be made in the factory or field.
FEELIS CO LTD
449 TAEJEON-DONG
GWANGJU-SI, GYEONGGI-DO, 464-805 KOREA
E341820
Class 2 LED Light Board, Cat. No. “LED Light Board”
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
7. These products cannot be wired in series.
Class 2 LED Strips, RGB LED Model designated as SH-XXX series, where XXX may be any numeric characters.
1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or 15 Volt AC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 30 Volt DC or 15 Volt AC.
3. These Class 2 LED modules are rated as noted in the model list table. When units are connected to a Class 2 circuit, they are
not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED, "Light Board Panels".
1. The LED modules are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are suitable for use in dry, damp or wet locations.
4. These products may be secured in place in the end product by any means available.
FIBEROPTIC LIGHTING INC
950 SE M ST
GRANTS PASS, OR 97526
E324239
Fiberoptic Sign, Model FLI LS-50.
1. This product needs to be enclosed in the end product.
2. This product must be enclosed in the end product. The enclosure should not be less than 14 in. x 6 in. x 6 in. If more than one
unit is used in a sign, each additional light source will require to be spaced at least 4 in. from each other within a compartment no
smaller the number of units times 14 in. x 6 in. x 6 in. Otherwise a Normal Temperature Test needs to be conducted in the end
product.
3. The wiring connection and mounting means were not evaluated and should be considered in the product.
4. If provided with a Power Cord, the product is only for use in Portable Signs.
5. This product is only suitable for use in dry locations.
January 23, 2014
50
SIGN COMPONENTS MANUAL (SAM)
FIRST SYSTEM CO LTD
HOUKOKU BUILDING 6F
2-26-1 IZUMI
HIGASHI-KU
NAGOYA-SHI, AICHI-KEN 461-0001 JAPAN
E359272
Class 2 LED modules, Model 9862-TM1A-12, may be followed by two or three alphanumeric numbers.
1. These products are only suitable for connection to a Class 2 power source rated as below or less.
Model No.
Maximum Input Voltage (V DC)
Current Rating (mA)
9862-TM1A-12
15
150
2. Units may be interconnected together by leads during normal use. When unit is connected to a Class 2 source, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
3. This product is suitable for use in dry and damp locations.
4. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
FLEXTRONICS LIGHTING SOLUTIONS INC
7320 W 162ND ST
OVERLAND PARK, KS 66085
E303645
Class 2 LED modules, Models: LW-UP-19-1C, LW-UP-19-1S, LW-UP-19-2S, LW-UP-19-3S, LW-UP-19-4S, LW-UP-19-1R.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED
power supply.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are suitable for use in dry and damp locations.
4. Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical
enclosure.
FOSHAN LIHAO ADVERTISING SIGNS CO LTD
WAREHOUSE 2, CHONGWEI
XINLIAN MEICHONG VILLAGE
LISHUI TOWN, NAHAI
FOSHAN, GUANGDONG 528244 CHINA
E338294
Neon Tube Support, tube support for indoor use Models LH-50, LH-70 maybe followed by B or C for Black or Clear type.
1. For indoor use only.
2. For use with neon supply rated 10KV, 5KV to ground maximum.
3. For securement by screw, rivet or solvent bonding. Solvent bonded with Trichloromethane, Bichloromethane, or Methylene
Chloride.
4. Mounting foot shall always point straight up or straight down.
5. These products shall not be used as cable support.
FRANCE A SCOTT FETZER CO
2268 FAIRVIEW BLVD.
PO BOX 300
FAIRVIEW, TN 37062
E239418
LED power supply, Cat. No. CLM-1250, LPS-1250, BTL-2450, and LPS-2450.
1. LED power supply are for dry and damp locations.
2. Each power supply output is Class 2.
3. LED power supply shall be installed in a suitable electrical enclosure.
4. Adjacent LED power supplies shall be installed at least 1 in. from each other end to end and 4 in. apart in other directions.
5. Wiring shall be rated 75C or greater.
LED power supply, Cat. Nos. BTL-24120, CLM-12120, LPS-12120, LPS-24120. Catalog numbers may be followed by one or
more alphanumeric characters.
1. LED power supply, Cat. No. for dry, damp or wet locations.
2. Liquid tight conduit fittings required for wet location use.
3. Each power supply output is Class 2.
4. Adjacent LED power supplies shall be installed at least more than 1 in. (25mm) end to end and 2 in. (51mm) side to side.
5. For stationary equipment only. Leakage current exceeded 0.5ma. Leakage current is less than 0.75ma.
LED power supply, Cat. Nos. CLM-1220, LPS-1220, BTL-2420 and LPS-2420.
1. LED power supplies are for dry and damp locations.
2. Each power supply output is Class 2.
3. LED power supply shall be installed in a suitable electrical enclosure.
4. Adjacent LED power supplies shall be installed at least 1 in. from each other end to end and 4 in. apart in other directions.
5. All wiring must be rated 75C or greater.
HID Lamp Ballast Assemblies, Cat. Nos. SBIP-200P, SBIP-250, SBIP-320P, SBIP-400 Series.
1. These products are suitable for use in dry and damp location only.
2. For SBIP-200P and SBIP-250 series, no temperature test is required in a sign when the minimum spacing between the HID lamp
and a polymeric material, between the HID lamp and adjacent ballast, or the HID lamp and other components is 7.0 inches.
3. For SBIP-320P and SBIP-400 series, no temperature test is required in a sign when the minimum spacing between the HID
lamp and a polymeric material, between a HID lamp and adjacent ballast, or a HID lamp and other components is 9.0 inches.
51
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4. A minimum spacing of 24 inches shall be kept between an HID lamp and combustible material located directly above the lamp.
5. These units shall not be mounted on combustible material or have combustible material located directly below them.
Tradenames of "Westrim" and "FRANCE".
LED Modules, designated as LEDBCCDDEEFG series where B, CC, DD and F may be replaced with any numeric characters; EE
may be replaced with DW, RD, BL, GN or AM; and G may be replaced with L, H or blank.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12 Volt
DC or less.
2. These products are each rated max. 0.6 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
LED power supply, Cat. Nos. LED-1220PS, LED-1260PS.
1. These power supplies have one Class 2 output with an input rating of 120/277 Vac and an output rating 12 Vdc. The output of
these power supplies has been evaluated to UL and cUL Class 2 output requirements for dc circuits.
2. Model LED-1220PS is intended for factory wiring installation where the unit is installed into the sign. It is suitable for use in dry
and damp locations only.
3. Model LED-1260PS is provided with conduit fittings and is intended for field and factory wiring installations. It is suitable for use
in dry, damp, and wet locations.
4. In the end product, power supply spacing to other heat producing components shall be located not less than 1 inch (25.4 mm)
apart when arranged end-to-end, and not less than 4 inches (102 mm) apart when arranged otherwise.
5. The input wiring shall be enclosed in the end product in a suitable electrical enclosure.
6. Consideration for connecting the metal enclosure to a suitable grounding point shall be considered in the end product.
7. These LED Drivers have not been evaluated for use with dimmers or any other control circuitry.
8. These drivers are suitable for fixed use only.
LED Isolated Class 2 Power Supply, Models LED-1260MPS.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a max. of one Class 2 output.
2. These products are provided with the following electrical ratings:
Model No.
LED-1260MPS
Input Voltage
(VAC)
Input
Freq
(HZ)
120-277
50/60
Input
Current
(A)
1.1
Output
Voltage
(Max. V
dc)
12
Output
Current
(Max. A)
5
3. These products shall be enclosed in the end product.
4. These products are suitable for use in dry and damp locations only.
5. These products are suitable for factory wiring only.
6. These products are to be operated on a max. 20 A branch circuit.
7. The suitability of input/output connections is also to be considered in end product use.
8. These drivers were tested at 60ºC max. ambient temperature. The need for conducting temperature test shall be considered in
the end product applications.
FULHAM CO LTD
12D FORD GLORY PLAZA
37 WING HONG ST
CHEUNG SHA WAN
KOWLOON, HONG KONG
E351199
“Sign Lighter” Induction lamp assemblies, Model XBBISLZZZ, where ZZZ may be numbers 250, 200, 80, 70 or 40 indicating
maximum lamp wattage; Model HF-AA-UNV-DC-XXX-T-YY, where XXX may be 250, 200, 80, 70 or 40 to indicate lamp wattage
and where YY may be numbers representing lamp color temperature.
1. These products are suitable for use in dry and damp location only.
2. These products have been temperature tested within a 6-sided wooden box with dimensions of 47.5 by 36 by 36 inches in a
horizontal (top of box, light pointed down) and vertical orientation with eight 12 AWG through-wiring conductors (4 in, 4 out). No
temperature test is required in a sign when the minimum volume indicated is provided.
3. No temperature test is required in a sign with a minimum horizontal spacing of 10 inches to a polymeric material, adjacent
ballast, or other components is 10 inches.
4. No temperature test is required in a sign with a minimum spacing of 28.2 inches shall be kept between the induction lamp and
any combustible material located directly above or below the lamp..
FULHAM CO LTD
12D FORD GLORY PLAZA
37 WING HONG ST
CHEUNG SHA WAN
KOWLOON, HONG KONG
E354191
Class 2 LED Power Supply, Models T1UNV012V-20L, T1UNV013V-20L, T1UNV024V-20L, T1UNV036V-20L, T1UNV0700-18L,
T1UNV1000-18L, T1UNV1400-18L.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated.
January 23, 2014
52
SIGN COMPONENTS MANUAL (SAM)
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. When conducting temperature test in the end product, the maximum temperature on the enclosure (case) shall not exceed
80°C. When provided with alternate enclosure material R/C (QMFZ2), Teijin Chemicals Ltd. (E50075),
Class 2 LED Power Supply, Models T1UNV012V-25C, T1UNV024V-25C, T1UNV036V-25C, T1UNV0700-25C, T1UNV0500-26C,
T1UNV0700-36C.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These lead connected products are suitable for use in commercial application only when marked with 277 V input voltage.
6. These units employ a Class 105 (A) insulation system on Transformer (T1).
Class 2 LED Power Supply, Cat. No. T1UNV012V-40C, T1UNV013V-40C, T1UNV024V-40C, T1UNV1000-36C, T1UNV140033C.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1,
300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be
determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-0 for Models T1UNV012V-40C, T1UNV013V-40C, and V-2 for Models T1UNV024V-40C, T1UNV1000-36C,
T1UNV1400-33C, and the necessity of additional fire barriers shall be determined in end product.
7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
FULHAM ELECTRONIC CO LTD
CHANGPING SCIENCE PARK
9 XINGCHANG RD
NANSHAOYUAN AREA
102200 BEIJING, CHINA
E349510
LED Driver with Class 2 Output, Models T1UNV012V-60L, T1120012V-60L, BL-120-12-60, T1UNV012V-60LA, BL-120-277-1260.
1. These products are to be used in maximum 50ºC ambient.
2. These products are provided with Class 2 output.
3. These products are intended for used in a maximum 20 A branch circuit.
4. These products are intended for use in dry and damp locations only.
5. These models are provided with 18 AWG input and output leads. The suitability of the wire shall be considered in end product
use.
6. These LED drivers shall be grounded through its mounting ears when used in end products.
7. These LED drivers are to be used in fixed wiring equipment only.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
LED Driver with Class 2 Output, Models T1UNV024V-100LS, T1UNV030V-100LS, T1UNV024V-60L.
1. When used in end product, the maximum temperature on case surface shall not exceed the temperature note as below:
Model No.
Degree, ºC
Tested ambient, ºC
T1UNV024V-100LS
89
60
T1UNV030V-100LS
88
60
T1UNV024V-60L
90
60
2. These products are provided with Class 2 output.
3. These products are intended for used in a maximum 20 A branch circuit.
4. These products are intended for use in dry and damp locations only.
5. These models are provided with No. 18 AWG input and min. No. 22 AWG output leads. The suitability of the wire shall be
considered in end product use.
6. These LED drivers shall be grounded through its mounting ears when used in end products.
7. These LED drivers are to be used in fixed wiring equipment only.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Driver with Class 2 Output, Models T1UNV012V-60LB, BL-120-277-12-60W, T1UNV012V-60LD.
1. When used in end product, the maximum temperature on case surface shall not exceed the temperature note as below:
Model No.
Degree, ºC
Tested ambient, ºC
53
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
T1UNV012V-60LB,
90
60
BL-120-277-12-60W,
T1UNV012V-60LD
2. These products are provided with Class 2 output.
3. These products are intended for used in a maximum 20 A branch circuit.
4. These products are intended for use in wet location.
5. These models are provided with No. 18 AWG input leads, R/C (AVLV2, AVLV8), AWM type, and No. 18 AWG output cable,
listed (QPTZ, CN), PLTC type. The suitability of the wire shall be considered in end product use.
6. These LED drivers shall be grounded through its mounting ears when used in end products.
7. These LED drivers are to be used in fixed wiring equipment only.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
10. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted below.
Model
Input (V, Amax)
Output (loaded)
T1UNV012V-60LB,
100-277 Vac, 0.708 – 0.268 A
11.47 V, 5.0 A
BL-120-277-12-60W,
T1UNV012V-60LD
LED Driver with Class 2 Output, Models T1M1UNV012V-20L, T1UNV012V-20L, T1UNV024V-20L, T1M1UNV024V-20L,
T4N4UNVxxxx-100K, T4N4UNVxxxx-100B, T4N4UNVxxxV-100K, T4N4UNVxxxV-100B.
1.These LED drivers have been evaluated using a resistive load resulting in the electrical rating below.
Model No.
Input V, Ampere
Loaded Output
(V dc, Ampere) x Channel number
T1UNV012V-20L
100/120/240/277,
12.25, 1.67
0.250/0.207/0.108/0.092
T1M1UNV012V-20L
100/120/240/277,
12.09, 1.67
0.251/0.207/0.108/0.094
T1UNV024V-20L
100/120/240/277,
23.70, 0.835
0.238/0.196/0.101/0.085
T1M1UNV024V-20L
100/120/240/277,
23.70, 0.835
0.244/0.203/0.103/0.088
2. These drivers have been tested in the ambient temperature. When used in end product, the maximum temperature on case
surface shall not exceed the temperature note as below:
Model No.
Tc (ºC)
Ta (Tested ambient, ºC)
T1UNV012V-20L, T1M1UNV012V-20L,
90
73.5
T1UNV024V-20L, T1M1UNV024V-20L
3. These drivers with metallic housing or display/keys are to be used in the suitable end product fire enclosure.
4. These products are intended for used in a maximum 20 A branch circuit.
5. These products are intended for use in dry and damp locations.
6. These LED drivers shall be grounded through its mounting ears when used in end product.
LED Driver with Class 2 Output, Models T1UNV024V-100LE, T1120012V-60LE, T1UNV012V-60LF.
1. These products have been evaluated with the following characteristics.
Model No.
Input type-
Output type-
Product is rated
T1UNV024V-100LE
T1120012V-60LE
T1UNV012V-60LF
[X] Branch Circuit
(Mains)
[X] Constant
Voltage
Output is
[X] Isolated
[X] Class 2
Dry and Damp
2. Rated output loading for these products were achieved by using electronic loads.
3. These products utilize a UL Recognized OBJY2 Class B electrical insulation system.
4. These products are intended for building in end product enclosure. Acceptability of the LED driver with respect to mounting,
spacing, casualty, temperature and segregation are to be determined as part of the end device evaluation.
5. These products are provided with 18 AWG minimum for input, 24 AWG minimum for output, rated min. 300 V, min. 105 ºC.
Strain relief was provided by embedding wires in potting compound. The suitability of the wiring connections, mounting means
and the need for a suitable enclosure shall be considered in the end product.
6. For model T1UNV024V-100LE, the temperature tests were performed at nominal 57ºC ambient and 64ºC for models
T1120012V-60LE and 63ºC for model T1UNV012V-60LF. Higher ambient shall be evaluated in end product use.
7. The LED drivers are intended to be connected to maximum 20 A branch circuit.
8. When the LED drivers are installed in the end-product, the measured exterior case temperature at the “Tc” locations shall not
exceed 90ºC. Refer to the following table for details:
9. The maximum leakage current was measured as 0.58 MIU when connected to a supply voltage of 240Vac for model
T1UNV012V-60LF. This LED drivers is to be used in a remotely-mounted unit connected and grounded via a fixed supply
connection or if the unit is intended to be an integral part of an end-product luminaire with a fixed supply connection and the
end-product standard for the luminaire does not require a leakage current measurement when the supply connection is fixed.
FUTURELIGHT CO LTD
239-7 DANGJUNG-DONG
GUNPO-CITY, GYEONGGI-DO 435-030 REPUBLIC OF KOREA
E364066
Class 2 LED modules, Models FL-TB@-XXX-@@@, FL-LGP-XXX-@@@, where X and @ can be any alphanumeric code.
January 23, 2014
54
SIGN COMPONENTS MANUAL (SAM)
1. These products are only suitable for connection to a voltage and energy limited Class 2 power source rated 12 V DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
FUTUREMEDIA DISPLAYS INC
#800 2120 HUTTON DR
CARROLLTON, TX 75006
E316529
Sign Fan Cooling System, Series FMCPX-N Fan Cooling System, where X may be blank, 1, 2, 3 or 4 and N may be 1, 2, 3 or 4.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These devices are to be used in accordance with the ratings and
load types as specified below.
(Input-Output) Operating Voltage (V)
Catalog Number
Input (AC)
Output (DC)
100-240
12
FMCPX-N Fan Cooling System
Max Output Current (rms) Type Load
5
Fans
3. These components are not provided with a suitable enclosure or sign body. The need for a suitable electrical enclosure and
mechanical mounting means shall be considered in the end product.
4. No testing has been conducted on these units. The need to conduct Input, Temperature, Dielectric Voltage Withstand, and
Grounding Continuity tests shall be considered in the end product. The need for additional testing shall also be considered in the
end product.
5. The need for suitable strain relief of the internal wiring due to potential user servicing shall be considered in the end product.
G E LIGHTING ISRAEL LTD
5 HAMELACHA ST.
NORTHERN INDUSTRIAL ZONE
71520 LOD, ISRAEL
E242790
Class 2 Power Supply, Models LET-60, LED 25 8V, LED 25 12V, LED 25 24V, LED 10CV 12, LED 10CV 12 PU, LED 10CV 24,
LED 10CV PU, LED 10CC 350, LED 10CC 350 PU.
1. The electrical ratings are as follows:
Input, 60 Hz
Output, ac
Model
V
A
V
A
VA or Pmax
LET-60
LED 25 8V
120
85-277
0.6
0.11-0.3
12
8
5.0
3.0
60 VA
25 Pmax
LED 25 12V
85-277
0.11-0.3
12
2.0
25 Pmax
LED 25 24V
85-277
0.11-0.3
24
1.0
25 Pmax
LED 25 8V
85-277
0.11-0.3
8
3.0
25 Pmax
LED 25 12V
85-277
0.11-0.3
12
2.0
25 Pmax
LED 25 24V
85-277
0.11-0.3
24
1.0
25 Pmax
LED 10CV 12,
LED 10CV 12 PU
120-240
0.175-0.120
12
0.833
10 VA
LED 10CV 24,
LED 10CV 24 PU
120-240
0.175-0.120
24
0.417
10 VA
LED 10CC 350,
120-240 0.175-0.120 2.3-28 0.350
10 VA
LED 10CC 350 PU
2. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
3. A suitable Fire and Electrical Enclosure shall be provided in the end product.
4. In the end product, power supply spacing to other heat producing
components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure.
5. These power supplies are only suitable for use in dry and damp locations.
Class 2 Power Supply, Models LED 60CV 12P, LED60CV 24P, LED 100 CV 8, LED 100 CV 12, LED 100 CV 24, LED 100 CV
48.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. The electrical ratings are as follows:
Input, 60 Hz.
Model
Output, DC
V
A
V
VA
LED 100 CV 8
100 - 277
1.3 - 0.5
8
100
LED 100 CV 12
100 - 277
1.3 - 0.5
12
100
LED 100 CV 24
100 - 277
1.3 - 0.5
24
96
55
SIGN COMPONENTS MANUAL (SAM)
LED 100 CV 48
100 - 277
1.3 - 0.5
48
96
LED 60CV 12P
100 - 277
0.8 - 0.3
12
60
LED 60CV 24P
100 - 277
0.8 - 0.3
24
60
January 23, 2014
3. These power supplies are only suitable for use in dry and damp locations.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Company name or trademarks
GE LIGHTING SOLUTIONS LLC
BLDG 338E
1975 NOBLE RD
EAST CLEVELAND, OH 44112 USA
,
and model designation.
E219167
Border tube kits, Includes Lens Cat. No. GExxBTL; Lens connector Cat. No. GExxBTLC; End cap Cat. No. GExxBTLEC; Exterior
corner kit Cat. No. GExxBTLXC; Interior corner kit Cat. No. GExxBTLIC; Base reflector Cat. No. GEBTBR; Base connector Cat.
No. GEBTBC; Cam lock Cat. No. GEBTCL. Canopy Kits, Cat. No. GECPL (8 ft length), GECPEC (end cap), GECPLC, (lens
connector), GEBTBCL, GEBTBC. Light guide kits includes: Light guide Cat. No. GEXNLGXX-XXX, Light Guide End Cap Cat.
No. GEXXXNLGECZZ, XXX may be any alpha letter representing color. ZZ may be any alpha letter representing size. Light
Guide Connector Cat. No. GEXXXNLGYZZ, XXX may be any alpha letter representing color, Y can be any alpha character
describing the type of connector. ZZ may be any alpha letter representing size.. Mounting clip Cat. No. GEXNMCXX; Supply
wire Cat. No. GEXNSXX; Splice connector Cat. No. GEXNSC1; Weather box Cat. No. GEXWBXX-XXX.
1. Border Tube Kit, Canopy Kit and Light Guide Kit are for Wet Location only use when enclosing LED’s connected to a Class 2
circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC.
2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure.
3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing.
LED power supplies, Cat. No. GEXLPS21, GEXNPS30-120, GEXNPS31-120
1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2.The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3.The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C.
4. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the
LED driver is used in combination with other equipment in the end-use product.
5. The drivers are intended for installation inside an electrical enclosure.
6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
7. The drivers are suitable for dry location use only except the drivers Models GEXNPS30-120 and GEXLPS21 are suitable for
damp location use.
LED array drivers, Models GEXLPS21-U, GEPS12-60U, GE060/MV/V12T12T1-A.
1. These components have been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2. The terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C.
4. The insulation system of the main isolation transformer designated (T2) in these models is a Class 105(A) insulation system.
Unless the modules are mounted as specified in condition of acceptability number 7, a temperature test is required when these
models installed within an electrical enclosure or raceway.
5. The maximum measured leakage current of a single unit is 0.49 mA. Leakage current measurements shall be performed when
multiple LED drivers are used in the final equipment or when the LED driver is used in combination with other equipment in the
end-use product.
6. The unit is intended for installation inside an electrical enclosure.
7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer
than 1 in. end to end or 4 in. side to side from adjacent LED power supplies.
8. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
LED power supplies, Model GEPS24-100U, GE100/MV/V24T1-A.
1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth
Edition, which would cover the component itself if submitted for Listing.
2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C.
4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an
electrical enclosure or raceway.
5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the
LED driver is used in combination with other equipment in the end-use product.
6. The unit is intended for installation inside an electrical enclosure.
7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer
than 1 in. end to end or 4 in. side to side from adjacent LED power supplies.
LED array drivers, Models GEPS 12-20, GEPS 24-20.
1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the
limits for Class 2 output requirements.
2. The transformers of these units employ Class 105 insulation system.
3. These components were intended for use in indoor Dry and DAMP location only.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
56
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
any other direction.
5. These components shall be installed inside an electrical enclosure.
6. Input and Output leads are style 1316, rated 600 V, 105C, VW-1. Minimum No. 18 AWG. The suitability of input and output
connections shall be determined in each end use application.
7. The maximum room ambient temperature permitted by the manufacture is 60C. The temperature measured on outside
enclosure of Models GEPS24-20 and GEPS12-20 are 67.2C and 77.9C respectively. The necessity of repeated Temperature
Test shall be determined in each end use application if minimum thermal spacings in accordance with Item 4 are not provided.
LED Dimmer, Model GEDM1 and GEDM1-A.
1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth
Edition, which would cover the component itself if submitted for Listing.
2. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C.
3. The unit is intended for installation inside an electrical enclosure.
4. This unit is provided with a Class 105(A) insulation system. The unit may be used within an electrical enclosure or raceway
without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED
power supplies.
5. The Xitanium Dimmer is only suitable for use in Class 2 circuits powered by Advance LED drivers with maximum input rating of
24Vdc, 4.1A, or 12VDC, 5A. Dimmer circuit is 0-10VDC.
6. This LED Dimmer Controller must be used with either a 100K Ohms Potentiometer or a standard 0-10 V DC dimmer switch.
7. For dry or damp location.
LED Strips, Class 2, Cat. Nos. GE-XX-XX-X-XXX, GE-XX-XX-XX-XXX, GE-XX-XX-XXX-XXX, GE-XX-XX-XXXX-XXX, GE-XXXX-XXXXX-XXX, GE-XX-XX-XXXXXX-XXX, GE-XX-XX-XXXXXXX-XXX, GE-XX-XX-XXXXXXXX-XXX, GE-XX-XXXXXXXXXXX-XXX, catalog numbers may vary per nomenclature. GE followed by: “XX” representing color: RD, RC, YG, GL,
SB, BL, WH, YA, WW, GR, PO, followed by: “XX” representing product line: CL, DS, XL, PT, XN, TM, MX, TU, PG, PX, PH, XH,
MH, SS, PM, MM, MH, BS, BD, BI followed by: “X” to “XXXXXXXXX” representing light strip final assembly or number of LEDs
per foot: LA, LE, AA, SX, LX, WXX, TXX, PX, XX followed by: “XXX” denotes any alphanumeric character that represents the
color temperature of the LEDs. Cat. Nos. GE-AA-BB-CC, where “AA” may be DS, XN, XNL, XNA, MX, MXL, PG, MM, MMD, SS,
PM, PMD, MXH, MXHL, BS, BD, BI, BIH, BSH, BDH, DSH or SSH or MS which represent product line; “BB” may be RD, RC,
YG, GL, SB, BL, WH, YA, WW, GR, PO or any alphanumeric character; and “CC” may be any alphanumeric characters or blank.
1. These products are only suitable for connection to a Class 2 power source.
2. When units are connected to a Class 2/ LPS circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2/ LPS supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products described in this section may be cut into segments per manufacture insulation instructions.
5. Units may be provided with UYMR2, 3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 Conditions of
Use as defined in the Sign Components Manual.
6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end
use product.
NOMENCLATURE:
Nomenclature for LED Strip Light: GE-XX-XX-X-XXX, GE-XX-XX-XX-XXX, GE-XX-XX-XXX-XXX, GE-XX-XX-XXXX-XXX, GE-XXXX-XXXXX-XXX, GE-XX-XX-XXXXXX-XXX, GE-XX-XX-XXXXXXX-XXX, GE-XX-XX-XXXXXXXX-XXX, GE-XX-XX-XXXXXXXXXXXX.
First Set of "XX" = denotes the color of the LED
RD
=
Red family
RC
=
Red/Orange family
YG
=
yellow family
GL
=
Green family
SB, BL
=
Blue Family
WH
=
White
YA
=
Amber
WW
=
Warm White
GR
=
Green
PO
=
Portland Orange
Second Set of "XX" = denotes product line
CL
=
channel letter
DS
=
double sided Power Strip
XL
=
tetra long strip
PT
=
power tetra
XN, XNL, XNA
=
Contour or Contour LS
TM
=
Mini
MX, MXL
=
Max
TU
=
Ultra
PG
=
Power Grid
PX
=
Power White XL
PH
=
Power White HO
XH
=
Power White XL HO
MM, MMD
=
Mini Max
SS
=
Power Strip
57
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
PM, PMD
=
Power Max
MH, MXH, MXHL =
MAX HO
BS
=
Shallow Box single sided
BD
=
Shallow Box double sided
BIH
=
Edgestrip
Third set of "XX" denotes Light Strip final assembly as noted below:
LA
=
Light Strip, assembled inside a plastic rod, 8 inch section
LE
=
Light Engine means same as Light strips
AA
=
Light engine, assembled inside a plastic rod, 16 inch section
SX or X
=
Number of LEDs per foot where X is 1 = 6 LEDs per foot etc. (X can be representative of 1 to 9 digits)
WXX
=
Wide Angle light diffuser, where the first X describes the PCB length, A for regular and L for long, and the
second X is an alpha numeric character of leds per foot.
PX
=
For PowerGrid (PG), Power Strip (SS) and Double Sided Power Strip (DS) only, where x equals the
number of LEDs per foot. Not Assembled in Tube. An optional X may be added to denote wire length
between modules where X is S for short, M for Medium, and L for Long.
XX
=
only to be used with DS product line, xx is number that correlates to total length in inches (48 = 48")
assembled in acrylic tube.
"XXX" denotes any alphanumeric character that denotes the Color Temperature of the LEDs i.e. 65k = 6500, 75k = 7500 etc.
Splice connector, Cat. No. GexxSCx; End caps, Cat. No. GexxECx.
1. These products are only suitable for connection to a Class 2 power source.
2. When units are connected to a Class 2/”LPS” circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2/”LPS” supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products described in this section may be cut into segments per manufacture insulation instructions.
5. Units may be provided with UYMR2, 3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 “Conditions
of Use” as defined in the Sign Components Manual.
6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end
use product.
LED Controller, LED Tetra FX Special Lighting Effects Controller, Cat. No. GEFX1
1. This product is suitable for only when connected to a Class 2 power source or LSP, Model GEXLPS20, GEXLPS21, GEXNOS30
or GEXNPS31 by GE. Rated Input is 12/24 V dc, Output is 12/24 V dc.
2. This product is a Class 2 device suitable for use in dry, damp and wet locations.
3. The controller shall be provided in a suitable housing when use in wet locations.
4. Lead wires are R/C (AVLV2), Style 2651, rated 105C, 300V. Not suitable for use inside walls, above ceiling or other similar
concealed spaces unless mounted inside an electrical enclosure.
5. The controller is provided with a DMX 5-pins input connector. The pin arrangements in the connector shall always be the same.
The DMX controller is capable of providing the 4 channel dimming, flashing, chasing, sequencing, color mixing, and color
changing functions.
LED wire, Cat. No. GExxSWx. Nomenclature for Splice Connectors, LED Wires, End Caps: xx denotes product line, CL = channel
letter, DS = double sided, XL = tetra long strip, PT = power tetra, XN = Exposed Neon, TM = Mini, MX = Max, TU = Ultra, PG =
Power Grid, PX = Power White XL, PH = Power White HO, XH = Power White XL HO, MM = Mini Max; 'x' denotes design revision
number.
1. These products are only suitable for connection to a Class 2 power source.
2. When units are connected to a Class 2/”LPS” circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2/”LPS” supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products described in this section may be cut into segments per manufacture insulation instructions.
5. Units may be provided with UYMR2, 3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 “Conditions of
Use” as defined in the Sign Components Manual.
6. The Light Guide has not been evaluated as an LED Strip Light enclosure or diffuser. Suitability shall be determined in the end
use product.
LED power supplies, Models GECLPS4.
1. LED power supply, Catalog No. GECLPS4 for dry and damp locations.
2. Each power supply output is Class 2.
LED power supplies, Models GECLPS4D.
1. LED power supply, Catalog No. GECLPS4D for dry and damp locations.
2. Each power supply output is Class 2.
LED power supplies, Models GECLPS6 and GECLPSPHA.
1. LED power supply, Catalog No. GECLPS6 for dry and damp locations.
2. Each power supply output is Class 2.
LED power supplies, Models GECLPS3.
1. LED power supply, Cat. No. GECLPS3 for dry and damp locations.
2. Each power supply output is Class 2.
LED power supplies, Models GECLPS5, GECLPSPH, GECLPSPW, GECLPSWH.
1. LED power supply, Cat. No. GECLPS5, GECLPSPH, GECLPSPW and GECLPSWH for dry and damp locations.
2. Each power supply output is Class 2.
Power supplies with Class 2 outputs, Models GEPS24-80, GEPS12-60, GEPS24-20.
1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp
locations.
2. These power supplies need to be installed in an enclosure with a means for the connection to conduit.
3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C. Similarly, for Model
January 23, 2014
58
SIGN COMPONENTS MANUAL (SAM)
GEPS24-20, a temperature test is required when installed in an enclosure smaller than 13.5 by 6 by 4 inches, but the maximum
temperature on the output transformer by thermocouple is 90°C.
4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet locations.
Power supplies with Class 2 outputs, Model GEXNPS30.
1. This component has outputs that qualify as being Class 2.
2. These components are intended for use in dry location only.
3. The transformer employs a Class B (130) Insulation System.
4. These components shall be installed in compliance with the enclosure and mounting requirements of the ultimate application.
5. The maximum room ambient temperature permitted by the manufacture is 50(C.
6. A Temperature Test is required of the power supply installed in an enclosure that measures less than 13.5 by 6 by 4 inches. The
maximum temperature on the output transformer by thermocouple is 110( C.
Power supplies with Class 2 outputs, Models GEPS24-180U, GE180/MV/V24T1-C
1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the
limits for LPS output requirements and additionally evaluated to comply with Class 2 output criteria.
2. The transformer employ Class B insulation system.
3. Power Supply is intended for use in indoor Dry and Damp location only.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
any other direction.
5. Input and Output leads are style 1316, rated 600 V, 105°C, VW-1. Minimum No. 18 AWG. The suitability of input and output
connections shall be determined in each end use application.
6. The power supply was submitted and tested for a maximum manufacturer's recommended Tc point described in the table below.
If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be
conducted in the end use product.
Model
GE180/MV/V24T1-C, GEPS24180U
Input Voltage, HZ
Max. Case Temp @ Tc, °C
Ambient, °C
100-277, 60
80
60
LED Light Engine, Cat. Nos. 1110-WH-ZZ-TTK, 1110-RD-ZZ-TTK, catalog numbers where: "ZZ" representing assembly version:
followed by: "TT" - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. Cat. Nos. 1111-XX-ZZ-Y-TTK,
catalog numbers may vary per nomenclature.: “XX” representing color: RD, RC, YG, GL, SB, BL, WH, YA, WW, GR, PO; “ZZ”
representing assembly version; ”Y” representing number of LEDs; followed by: “TT” - Optional - represents the color temperature of
the LEDs in degree “K” Kelvin.
1. These products are only suitable for connection to a Class 2 power source.
2. When units are connected to a Class 2/”LPS” circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2/”LPS” supply.
3. These products are suitable for use in dry, damp and wet locations.
4. The suitability of the LED Light Engine mounting means shall be determined in the end-use application.
5. The suitability of the LED Light Engine to be used without an additional electrical enclosure shall be determined in the end-use
application.
6. These products described in this section may be cut into segments per manufacture insulation instructions.
7. Units may be provided with UYMR2, 3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 “Conditions of
Use” as defined in the Sign Components Manual.
LED Driver with Class 2 Output, Models GEPS12D-60U, GEPS24D-80U.
1. These LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. These products are provided with the following electrical ratings:
Model No.
Input Voltage (V
ac)
Input Freq
(HZ)
Input Current Output Voltage Output Current
Output
(A)
(V dc)
(A)
Power (W)
GEPS24D-80U
100-277
50/60
1.1
24
3.3
80
GEPS12D-60U
100-277
50/60
0.85
12
5.0
60
3. The load powered by the Class 2 output of the LED drivers are suitable for use in dry, damp and wet locations.
4. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
5. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
6. These products shall be enclosed in the end product.
7. The unit is intended for being used in permanently wired signs.
8. The suitability of output leads, rated No. 24 AWG minimum, rated 80°C minimum, 600 V, shall be determined in end product
use.
9. These units may provided with Dimming Input (Purple and Gray wires) to control output current range, the suitability shall be
determined in each end-use application.
10. These products are intended for use in dry and damp locations
LED Driver with Class 2 Output, Model 1110PS-60S.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1.
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below:
Model
Ta (°C)
LD-60-UV-1214V
40
4. These LED drivers are intended for use in dry and damp locations except that models LD-60-UV-1214V and LD-60-UV-1214VSC are suitable for dry location only.
5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a
suitable enclosure shall be considered in the end product.
59
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. The need of the grounding means shall be determined in the end product.
8. These LED drivers shall be enclosed within a suitable end product enclosure.
9. For model LD-60-UV-24V-DIW, the conduit knockout test was not conducted. The suitability is to be determined in end product.
10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
11. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Driver with Class 2 Output, Model GEPS12-180U.
1. The output (Red/Black) of each unit complies with Class 2 criteria of UL 1310.
2. The device is provided with 18 AWG input and output leads. The suitability of input and output connections shall be determined
in end-use application.
3. The suitability of grounding means shall be determined by end product.
4. The device is not intended for field wiring used.
5. The device is intended to be connected to a maximum 20 A branch circuit.
6. The devices are of the constant current type that requires the proper number of LED modules and controllers that does not
exceed the maximum output voltage/current.
7. The measured maximum external enclosure temperature (Tc) is 77.2 degree C when the room ambient temperature are 60
degree C. The suitability shall be determined in end application.
8. The devices employ input surge suppression protection, Cat. No. S14K385E2K1 under UL File E321126, which is intended enduse SPD type 2. The suppressed voltage rating is 385 Vac. The suitability of use of this component shall be determined in the
end-product application.
9. No mechanical test has been conducted for the models and the metal chassis is considered as dead metal. The devices shall
be mounted in the intended manner in an enclosure, having adequate strength and thickness with acceptable spacing being
provided.
10. The device has been evaluated for dry and damp locations use only.
11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Driver Extended Enclosure, Model No. GEPSJB60.
1. The J-Box extended enclosure has been evaluated only for use and connection to LED Class 2 Drivers Models GEPS12-60,
GEPS12D-60U, GEPS24-80, GEPS24D-80U, GEPS12-60U-NA, GEPS12-60U-GL, GEPS24-100U-NA, and GEPS24-100UGL.2. These products complete the electrical enclosure when installed over the primary wiring of the LED driver.
3. The suitability of the mounting shall be determined in end use application.
4. The enclosure has been evaluated only for use in Dry and damp locations only
5. Supply connection shall be determined in the end used application.
6. Ground Screw size is No. 6 thread forming screw with cupped washer is provided for grounding. The maximum size ground
wire that can be used is 14AWG. The maximum size branch circuit that the units can be connected to is 15A unless a 1614AWG six inch pigtail lead supplied by sign company is connected to ground terminal and then spliced to 12AWG ground wire
of a 20 A branch circuit.
7. Cover Screw shall not be of a thread forming or self-tapping type.
8. To keep the enclosure from rotating, the Enclosure shall be secured by at least one mechanical fastener.
9. The J-box has been evaluated for an ambient of 40°C.
10. The J-box label shall be marked for a 75°C supply wire connection.
LED Driver with Class 2 Output, Cat. Nos. GEPS12-60U-NA, GEPS12-60U-GL, GEPS24-100U-NA and GEPS24-100U-GL.
1. These power supplies are provided with Class 2 outputs
2. These products with Class 2 outputs are suitable for use in dry and damp locations.
3. Model Nos. GEPS12-60U-NA, GEPS12-60U-GL have been tested in an oven at max. 40ºC ambient and Model Nos. GEPS24100U-NA, GEPS24-100U-GL in an over at max. 55 ºC. Maximum case temperature at (Tc) for all models should not exceed
85°C.
4. The suitability of grounding connection shall be determined in the end-use product.
5. These products shall be enclosed in the end product.
6. These products are provided with the following electrical ratings:
Model
Input, 50/60 Hz
Rated Output
V
A
V DC
A DC
W
GEPS12-60U-NA,
120-277
Max. 0.65
12
5.0
60
GEPS12-60U-GL,
GEPS12-60U-NA,
120-277
Max. 1.10
24
4.0
96
GEPS12-60U-GL
7. These products are suitable for factory wiring only.
8. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end,
and 101.6 mm (4 in.) from side to side.
9. The suitability of input/output leads and the wring shall be determined in end product use.
10. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
11. These products shall be enclosed in the end product.
LED Driver with Class 2 Output, Model GEPS24-180U-GL.
1. The device shall be used within Recognized ratings as specified above.
2. Each output of the unit complies with Class 2 criteria of UL 1310. Multiple output units may exceed Class 2 when the output
terminations are interconnected. Do not interconnect output terminations.
3. The device is provided with 18 AWG input and output leads. The strain relief test was not conducted on this device. The
suitability of input and output connections shall be determined in end-use application.
January 23, 2014
60
SIGN COMPONENTS MANUAL (SAM)
4. Temperature Test has been conducted using resistive loading, and the LED Driver was mounted on a heat sink, aluminum,
approx. size 500 mm by 300 mm by 100 mm. The measured maximum external enclosure temperature (Tc) is 79.4 ºC when the
room ambient temperature is 60 ºC. The suitability shall be determined in end application.
5. Transformers employ Class 130(B) insulation system.
6. The suitability of grounding means shall be determined by end product.
7. The device is intended for factory installation only.
8. The device is intended to be connected to a maximum 20 A branch circuit.
9. The devices are of the constant current type that requires the proper number of LED modules and controllers that does not
exceed the maximum output voltage/current.
10. The device has been evaluated for dry and damp location use only.
Class 2, LED module, Model GEF.
1. These products are suitable for use in dry, damp and wet locations when supplied with a Class 2 power source rated 24 Volt DC
or less.
2. Suitable only for connection to a Class 2/LPS circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. The LED module is intended to be supported by recessed double contact lampholders ANSI designation R17d.
Class 2 Power Supply, Models GEPS12-25U-NA, GEPS24-25U-NA.
1. The electrical ratings are as follows:
Input, 60 Hz
Output, ac
Model
GEPS12-25U-NA
V
A
V
A
VA or Pmax
85-277
0.11-0.3
12
2.0
25 Pmax
GEPS24-25U-NA
85-277
0.11-0.3
24
1.0
25 Pmax
2. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
3. A suitable Fire and Electrical Enclosure shall be provided in the end product.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. These power supplies are only suitable for use in dry and damp locations.
GEMINI INC
103 MENSING WAY
CANNON FALLS, MN 55009
E16382
Plastic Channel Letters, Cat. No. Plastic Channel Letters.
1. The channel letters may be used as an electrical enclosure when provided with sign face material in the end-use application
that is suitable for electrical enclosure use.
2. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign
face.
3. Openings for drain holes, conduit, electrode receptacles and mounting shall be provided in accordance with the Standard.
4. The channel letter plastic is rated 80°C.
5. For outdoor or indoor use.
6. Spacings from the channel letter to the enclosure for neon transformers or power supplies shall be in accordance with
Standard UL 48.
Plastic Channel Letters, Plastic Indoor Channel Letters.
1. The channel letters have been evaluated for indoor application only.
2. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face.
Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard.
3. The channel letter plastic is rated 50°C.
4. The channel letter may be used as an electrical enclosure when provided with a sign face material in the end-use application
that is suitable for electrical enclosure.
5. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard
UL 48.
Plastic Channel Letters and Face, Plastic Indoor Channel Letter Sign Body and Face
1. The channel letters have been evaluated for indoor application only.
2. The channel letters are not suitable as an electrical enclosure.
3. The channel letters are suitable for Class 2 LED and neon applications.
4. The channel letter plastic is rated 50°C.
5. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard.
6. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face.
7. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard
UL 48.
Aluminum reinforced thermoplastic sign face trim, Type Gem Brand.
1. These trim materials are used to secure a rigid thermoplastic sign face to an outdoor or indoor sign.
2. The ability of the trim to exclude water from contacting live parts needs to be evaluated in the end product.
3. Minimum No. 8 sheet metal screws need to be provided for securing the trim to the sign body. The maximum spacing between
screws shall not exceed 18 in. and no fewer than four screws are to be used per face.
4. These products do not comply with enclosure requirements.
5. The following are among the items to be considered in the end-use application.
1. Acceptable for use in wet locations.
2. Water exclusion must be determined in the end product.
3. Minimum 5 cm (2 in.) spacing from heat producing components required.
61
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4.
The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified
adhesives may be applied for the final bond.
Sign Face Generic Material
Solvent
Final Bond Adhesive
Sign Trim Generic Material
Methyl Methacrylate
Weld-On #4 or
Weld-On #16, Weld-On
Cellulose Acetate Butyrate
(Acrylic)
( Methylene Chloride )
#58
(Polycarbonate)
Weld-On #4 or
Weld-On #58, Lord
Cellulose Acetate Butyrate
Methylene Chloride
Adhesive #7550
Plastic Channel Faces, Type Gemini Gemlite Channel faces and Gemini Edge Glo faces
1. The sign faces have been evaluated for indoor & outdoor applications.
2. The sign faces are not suitable as an electrical enclosure.
3. The sign face plastic is rated 50°C.
4. The sign face for channel letter is not to be considered as providing a weatherproof enclosure, therefore all internal
components shall be suitable for outdoor use or shall be completely enclosed and protected from weathering.
5. The neon tube or LED shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from
the sign face.
6. The sign face may be used with either plastic or metal channel letters.
Plastic Channel Letters, Type Indoor, outdoor designated "GEMINI FORMED SIGN BODY" for Class 2 powered LED modules
strips.
1. These products are only suitable to house LED modules strips that are powered by UL Listed or R/C Class 2 Power Supply
rated max 30 VDC or max 15 VAC.
2. These products are not suitable for use as electrical enclosures.
3. These products shall be provided with mounting instructions.
4. For outdoor applications, if these products are used to house components other than Class 2, then all internal components
shall be suitable for outdoor use or shall be suitably enclosed.
Plastic Channel Letters, Type Gemini Channel Letters
1. The Gemini Channel Letters have been evaluated for indoor & outdoor applications.
2. The Gemini Channel Letters are not suitable as an electrical enclosure.
3. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign
face.
4. The Gemini Channel Letter plastics are rated 80C minimum.
5. Suitable for use in terminating conduit trade size up to 3/4 in.
6. Water exclusion must be determined in the end product.
Plastic Channel Letters, Type Gemini Non-enclosure rated channel letters, Type Gemini Channel Letters.
1. The Gemini Channel Letters have been evaluated for indoor & outdoor applications.
2. The Gemini Channel Letters are not suitable as an electrical enclosure.
3. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign
face.
4. The Gemini Channel Letter plastics are rated 80C minimum.
5. Suitable for use in terminating conduit trade size up to in.
6. Water exclusion must be determined in the end product.
Plastic Channel Letters indoor and outdoor Type Stainless Steel Fabricated channel letters.
1. These products have been evaluated for indoor & outdoor applications.
2. The suitability of the enclosure shall be determined in the end product.
3. The products shall be provided with mounting instructions.
4. These units are to be used with only Class 2 power supplies rated Max. 30 VDC or 15 VAC.
5. This product is to be connected via UL Listed (QPTZ) power limited circuit cable or other equivalent wiring means. Suitability
shall be determined in the end use.
6. When provided LED drivers need to be remotely mounted inside metal electrical enclosures secured outside the sign body in
raceways or behind the mounting surface.
7. Grounding is necessary from the SS body of each letter to the enclosure housing the transformer or driver.
GENERAL LED
SUITE 108
1111 ARION PKY
SAN ANTONIO, TX 78216
E354486
Class 2 power supply, Models PS12-60W-100-277V, PS12-60W-100-277V-ENC.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Max Output (V, A, W)
Model
Input (V, Hz, A, W)
PS12-60W-100-277V, and
100-277; 50-60; 0.8; 75
12.0; 5.00; 60
PS12-60W-100-277VENC
3. In the end product, power supply spacing to other heat producing components shall be at least .4 mm (1 in.) from end to end,
and 101.6 mm (4 in.) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products have been tested in oven at min 40ºC ambient, with the maximum case temperature, Tc of 88.7ºC.
7. These products are intended for use in dry or damp locations only.
8. The suitability of input/output leads and the wring shall be determined in end product use.
9. These products are constant voltage type that requires the proper number of LED modules and controllers that do not exceed
the maximum output current.
10.These LED drivers are intended to be operated on a maximum 20 A branch circuit.
January 23, 2014
62
SIGN COMPONENTS MANUAL (SAM)
11.These LED drivers are intended for use in fixed equipment only.
Class 2 power supply, Model PS1050-150W-100-277V-2O-G1-xxxx, where "xxxx" can be any alphanumeric characters or blank.
1. These power supplies have been evaluated as isolated LPS output requirements for dc circuits with a maximum of four Class 2
outputs.
2. These products are provided with the following electrical ratings:
Max.
Input
Input
Output
Output
Voltage
Input
Power
Output Voltage
Current
Power
Series No.
(V)
Current(A)
(W)
(Vdc)
(A)
(W)
Vo1
19-36
1.05
37.8
100~277
Vo2
19-36
1.05
37.8
PS1050-150W-100Vac, 50/60
2.1
170
277V-2O-G1-xxxx
Vo3
19-36
1.05
37.8
Hz
Vo4
19-36
1.05
37.8
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wring shall be determined in end product use.
8. The output leads of these products cannot be interconnected in the end product.
9. These LED drivers are provided with a multi-conductor AWM wire consisted of two (purple and gray) 22 AWG, min 80°C, min
300 V leads for connecting a dimmer to vary the output current. The connecting diagram is shown as below. The leads are
investigated for use in Class 2 output circuit and cannot be interconnected with the other output of these drivers. The dimmer
may be a 0-10 Vdc input voltage or a 0-300 kohm variable resistor.
Vcc
Vcc
Ri
Ri
1-10V
INPUT (PURPLE )
1-10V
INPUT (PURPLE )
V 1-10Vdc
Rx (0-300 kohm)
GND (GRAY )
GND (GRAY)
or
Class 2 power supplies, Models PS0700-150W-100-277V-2O-Y-xxxx, PS1050-150W-100-277V-2O-xxxx and PS12-60WSL-100277V-xxxx, where Y can be blank or G1 and "xxxx" can be any alphanumeric character or blank.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits.
2. These products are provided with the following electrical ratings:
Input
Input
Output
Max. Output
Input
Output Voltage
Model No.
Voltage
Power
Current
Power
Current(A)
(Vdc)
(V)
(W)
(A)
(W)
Vo1
24-54
0.70
37.8
*PS0700-150WVo2
24-54
0.70
37.8
100~277 Vac,
100-277V-2O-Y2.1
168
50/60 Hz
Vo3
24-54
0.70
37.8
xxxx
Vo4
24-54
0.70
37.8
Vo1
19-36
1.05
37.8
Vo2
19-36
1.05
37.8
PS1050-150W100~277 Vac,
2.1
170
100-277V-2O-xxxx
50/60 Hz
Vo3
19-36
1.05
37.8
Vo4
19-36
1.05
37.8
PS12-60WSL100~277 Vac,
0.9
90
12
5
60
100-277V-xxxx
50/60 Hz
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wiring connections shall be determined in the end product.
8. When used in CUL Certified end products, the output leads of power supplies, models PS0700-150W-100-277V-2O-Y-xxxx and
PS1050-150W-100-277V-2O-xxxx are to be made inaccessible in the end product application.
9. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
10. These products are provided with a 0-10 Vdc input voltage or a 0-300 kohm (short/open) variable resistor dimmer leads. The
suitability of the dimmer leads wiring shall be determined in end product. For reference, below is a general dimmer connection
diagram.
or
GIANTECH INDUSTRIES CO LTD
209-5 MIN-SHENG RD
WU FENG
E343579
63
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
TAICHUNG HSIEN, 413 TAIWAN
Class 2 LED Module, Models NA00 and NEA0.
1. The suitability of the mounting means shall be determined.
2. These products are suitable for use in dry, damp and wet location.
3. The LED Modules are intended for connection to a Class 2 power source, rated 12 Volt DC.
4. These products are rated as the following:
No. of LED per Module
Max. Wattage per LED
Module
Voltage (V dc)
Total Constant Current (A)
NA00
54
5W
12
0.5
NEA0
306
23 W
12
2
Model
5. Model NEA0 was evaluated based on being connected to a source of supply only by solder leads and have not been evaluated for
supply connections made by any type of connector.
6. The suitability of the diffuser to serve as a barrier or enclosure shall be determined in the end use product. Consideration for
addressing electrical, flammability, and mechanical properties shall be given.
GLOBAL LUX INC
227 PIERRE CONEFROY
BOUCHERVILLE, QC J4B 6N3 CANADA
E346373
LED Modules, Models EV 01WXX, EV105WXX, EV205WXX, EV 07WXX, EV310WXX, EV415WXX, GL-EV1-05W-IP-XX(#)
where that x may be R, G, B, Y, CW, WW, P or O indicating LED Color.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
(#) Where that x may be R (Red), G (Green), B (Blue), Y (Yellow), CW (Cool White), WW (WarmWhite) or YW (Yellow White)
indicating LED Color.
LED Modules, Models GL-EV2-1W150-XX, GL-EV3-15W150H0-XX.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
GLOBAL SIGN PRODUCTS LLC
110 INDUSTRIAL BLVD
PO BOX 817
EASTMAN, GA 31023
E323557
Structural Panel, Designated "Signabond V.5", "Signabond V.3", "Signabond Lite", "Signabond Lite 350".
1. This product is intended as an outer decorative covering, has not been investigated for use as an electrical enclosure.
2. The use of this product is limited to only decorative and sign body applications.
3. The suitability of the "fit" of the face material and the "secureness" of the clamp mechanisms on the sign will be judged in the
end use sign application.
4. This product has not been evaluated for component support.
5. This product is acceptable for use in dry, damp and wet locations
6. The water exclusion must be determined in the end product.
7. This product has not been evaluated for the termination of conduit. Suitability of the connection of conduit shall be determined in
the end product.
8. All exposed edges of a structural panel, including drilled holes, etc., are be treated with two coats of outdoor paint or wood
coating.
9. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in from a
point of support
10. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
GLOBE TO GREEN LIGHTING LLC
155A 10TH ST
PASSAIC, NJ 07055
E344189
Class 2 LED Module, Models Aurora I R, Aurora I W, Aurora II W, Aurora Mini, Aurora Extension, Aurora EX, Aurora SV, and G2G
NOX.
1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or 15 Volt AC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than 30 Volt DC or 15 Volt AC.
January 23, 2014
64
SIGN COMPONENTS MANUAL (SAM)
3. These Class 2 LED modules are rated as noted in the model list table. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2.
5. These products are not required to be enclosed or protected from the weather in the end product.
GLUX VISUAL EFFECTS TECH (SHENZHEN) CO LTD
Room 504, Bldg A4
Oct Eastern Ind Zone
Nanshan District
Shenzhen, Guangdong 518035 CHINA
E365838
Sign component, changing message, Model BAtn10.
1. Acceptability for multiple connections (daisy chaining) not exceeding 15 A (based on 14 AWG power supply cord) on a single
branch circuit shall be determined by the end product requirements.
2. This product was tested for use at a room ambient temperature of 40°C. Testing was conducted on an open bench positioned in
a vertical position facing horizontally. The need for conducting temperature testing in the end product shall be considered where
the units are installed in a higher ambient.
3. The suitability of the mounting means shall be determined in the end use.
4. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
5. The suitability of power connector and power cord needs to be determined in the end use.
Sign component, Model DC limit.
1. This product was tested for use at a room ambient temperature of 40°C. The need for conducting temperature testing in the end
product shall be considered where the units are installed in a higher ambient.
2. This product was tested for dry and damp locations.
3. The suitability of the mounting means shall be determined in the end use.
4. This product is intended to operate within the manufacturer's specified ratings.
5. This product is permitted only on the load-side of an isolating transformer, power supply which output rated 3-5Vdc, max. 4.2A.
6. This product has been evaluated for class 2 output.
7. Spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to
top of enclosure; or temperature test in the end product shall be considered.
8. This product shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less than 4 inches (102
mm) apart when arranged otherwise; or temperature test in the end product shall be considered.
9. This product is not provided enclosure; suitable enclosure shall be considered in end product.
10. Grounding shall be considered in end product.
11. These devices are for factory wiring only.
GM LIGHTING LLC
SUITE F
9830 W 190TH ST
MOKENA, IL 60448
E326687
LED Strips, Models LTR300-WW, LTR300-xx, LTB-8, LTB-16, LTR300WP-SO-xx, LTR60WP-SO-xx, LTR30WP-xx, LTR60WP-xx,
LTR300WP-xx , LTR300-SO-PW, LTR300-SO-WW, LTR150-RGB, LTR150WP-RGB;; xx suffix is a representation for any color.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED strips, Model LTR120024-HO-xx, LTR120024WP-HO-xx where suffix “xx” is designation of LED colors, rated 24 Vdc
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
GOQLED CO LTD
290-31 GAMIL-DONG
GAMIL-DONG
HANAM-SI, GYEONGGI-DO 465-190 REPUBLIC OF KOREA
E344463
Class 2 LED Module, GOQ1LED, GOQ2LED, GOQ3LED, GOQ4LED, GOQ5LED, CAP TYPE 3 LED and CAP TYPE 4 LED.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited
circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
65
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
GRANDLITE INTERNATIONAL CORP
505 S YORBITA RD
CITY OF INDUSTRY, CA 91744
E352604
Class 2 LED Power Supply, designated EE-L20W-10V-nnnnMA, EE-L20W-12V-nnnnMA, EE-L20W-13V-nnnnMA, EE-L20W15V-nnnnMA, EE-L20W-17V-nnnnMA, EE-L20W-18V-nnnnMA, EE-L20W-22V-nnnnMA, EE-L20W-24V-nnnnMA, EE-L20W36V-nnnnMA, EE-L20W-52V-nnnnMA, EE-L40W-09V-nnnnMA, EE-L40W-10V-nnnnMA, EE-L40W-12V-nnnnMA, EE-L40W13V-nnnnMA, EE-L40W-15V-nnnnMA, EE-L40W-18V-nnnnMA, EE-L40W-22V-nnnnMA, EE-L40W-24V-nnnnMA, EE-L40W36V-nnnnMA, EE-L40W-48V-nnnnMA, where the optional suffix "Cnnnn" may be any alphanumeric character. Model EEL90W-XXV-YZ-E, where XX can be 19, 24 or 36; Y can be G or T; Z can be G or T; and E can be any number from 170 to 999;
which may be followed by suffix "DV".
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. When conducting temperature test in the end product, the maximum temperature on the enclosure (case) shall not exceed
80°C. When provided with alternate enclosure material R/C (QMFZ2), Teijin Chemicals Ltd. (E50075),
8. Class 2 Power Supply, Model EE-L20W-52V-nnnnMA are suitable for use in US only.
GRATE SIGNS INC
4044 W MCDONOUGH ST
JOLIET, IL 60431
E227355
Structural Siding Cat. No. E-Z Channel Letter
1. The aluminum siding shall be bonded to the point of conduit connection to the sign.
2. The water tightness of the enclosure requires evaluation.
GRE ALPHA ELECTRONICS LTD
UNIT 323 & 325, 3RD FL
NO 1 SCIENCE PARK WEST AVE
HONG KONG SCIENCE PARK
SHATIN N T, HONG KONG
E238096
LED Class 2 Drivers, Models SLD45-108V-XX, SLD45-110V-XX, SLD45-112V-XX, SLD45-115V-XX, SLD45-118V-XX, SLD45121V-XX, SLD45-124V-XX, SLD60-112V-XX, SLD60-115V-XX, SLD60-118V-XX, SLD60-121V-XX, SLD60-124V-XX.
1. These power supplies have a single output that complies with Class 2 output requirements.
2. Power supply, Model series –FC and –FE are suitable for use in dry, damp, and wet locations. Model series -FT is suitable for
indoor use. Model series –FT is suitable for wet and damp location when provided with a UL Listed NEMA Type 3 enclosure.
3. Power Supply, Model series –FC and –FE are provided with aluminum enclosure that complies with enclosure requirements.
4. Power supply, Model series –FT shall be provided with a suitable enclosure to cover terminals.
5. Each power supply shall be installed in accordance with the installation instructions.
Class 2 LED Illumination Module, Models SLD60-xyyz-FC Series, where x can be 1 or 2; yy can be 05, 06, 08, 10, 12, 15, 18,
21, 24 or 48; and z can be B, C, D, E or F.
1. These power supplies have a maximum of two Class 2 outputs. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits. Consideration shall be given to accessibility of secondary circuits with output
ratings greater than 42.4 Vdc in Canadian end product applications.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. When used in wet locations, the
output circuits shall be inaccessible unless the output circuits are limited to a max. 30 Vdc.
3. Power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2
inches spacing to top of enclosure.
4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
Class 2 LED Illumination Module, Model SLD120-xyyz-FC Series, where x can be 2; yy can be 08, 10, 12, 15, 18, 21, 24, 27, 36
or 48; and z can V.
1. These power supplies have maximum of two Class 2 outputs. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations, except models SLD120-236V-FC
and SLD120-248V-FC are suitable for use in dry and damp locations due to output voltages above 30 V dc.
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
4. When used in wet locations, each unit shall be provided with listed (QCRV) and CN 1/2 inch liquid tight conduit fittings.
Class 2 LED Power Supplies, Model SLD25-XXXV-FW Series, where XXX is any number, may be provided with suffix i or o.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These power supplies are only suitable for use in dry and damp locations.
January 23, 2014
66
SIGN COMPONENTS MANUAL (SAM)
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 LED Power Supplies, Model Class 2 powered LED module dimmer, Model LED PWM Dimmer Module SLD-DIM.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated max 10VDC.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
4. These products are rated per the Table below.
Max. Output
Model
Input, Vdc
Volts
Watts
Control Voltage, V
LED PWM Dimmer Module SLD-DIM
0-10 Vdc
30
3
(0-5V)
5. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
6. These products are suitable for use in dry and damp locations without additional enclosures.
GREAT LAKES SIGN SUPPLY CO
SUITE 273
732 S 11TH ST
NILES, MI 49120
E29252
Electronic Sign Flasher, Model 22 with suffixes -01, -01-HO, -02, -02-HO, -A2, -A2-HO, -A2S, -C2, -C2S, or -C3.
1. Temperature testing has been conducted with the 1 and 2 circuit models in an enclosure measuring 4-3/4 by 4-1/2 by 3-1/2
inches, and with the 3 circuit model in an enclosure measuring 6 by 6 by 9 inches. Consideration shall be given to conducting a
temperature test if flasher is installed in a smaller enclosure or if mounted within 2 inches of other heat producing components.
2. These flashers are rated 120/240 Vac input with maximum load switching ratings of 15A at 100 cycles per minute, 10A at
switching rate of 250 cycles per minute.
3. These flasher have not been evaluated for DC load ratings.
4. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
5. These flashers as suitable for use in Dry and Damp Locations.
Electronic Sign Flasher, Models 33-C3, -C4, -C5 and Model 33-S1 to -S5 inclusive with Suffix F, M, S or XS with or without
designation.
1. Temperature testing has been conducted with product in an enclosure measuring 5-5/8 by 7 by 10 inches. Consideration shall
be given to conducting a temperature test if flasher is installed in a smaller enclosure or if mounted within 2 inches of other heat
producing components.
2. These flashers are rated 120/240 Vac input with maximum load switching ratings of 15A at 100 cycles per minute, 10A at
switching rate of 250 cycles per minute.
3. These flashers have not been evaluated for DC load ratings.
4. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
5. These components are suitable for use in Dry or Damp Locations.
Electronic Sign Flasher, Model 33S with Suffix Nos. 6 to 20 inclusive, followed by additional Suffix "M," "S," or "XS" with or
without additional suffix numbers or letters.
1. Temperature testing has been conducted on a 9 circuit model in an enclosure measuring 14-1/2 by 8 by 6 inches. Consideration
shall be given to conducting a temperature test if flasher is installed in a smaller enclosure or if mounted within 2 inches of other
heat producing components.
2. These flashers are rated 120/240 Vac input with the through load rating of 120/240 Vac and maximum load ratings of 15 amps
at a switching rate of 100cycles
3. These flasher have not been evaluated for DC load ratings.
4. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
5. These components are suitable for use in Dry or Damp Locations.
Electronic Sign Flasher, Models 66-C3, 66-C4, 66-C5 and 66-C6.
1. Temperature testing has been conducted on models 66-C6 and 66-C5 in an enclosure measuring 5 by 10 by 10-3/4 inches and
models 66-C3 and 66-C4 in an enclosure measuring 5 by 8 by 9 inches. Consideration shall be given to conducting a
temperature test if flasher is installed in a smaller enclosure or if mounted within 2 inches of other heat producing components.
2. These flashers are rated 120/240 Vac input with maximum load switching ratings of 15A at 100 cycles per minute, 10A at
switching rate of 250 cycles per minute. These flasher are rated 120 Vac input with the through load rating of 120 Vac and
maximum load ratings 20 A at a switching rate of 250 cycles per minute for models 66-C3 and 66-C4, 17.5A at a switching rate
of 250 cycles per minute for models 66-C5 and 66-C6, and 12.5A at a switching rate of 430 cycles per minute for all models.
3. These flashers have not been evaluated for DC load ratings.
4. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
5. These components are suitable for use in Dry and Damp Locations.
Electronic Sign Flasher, Models 55-A4F, 55-A6F, 55-A8F, 55-A4S, 55-A6S and 55-A8S.
1. Temperature testing has been conducted with product in open air without an additional enclosure. Consideration shall be given
to conducting a temperature test if flasher installed in an enclosure smaller that 12 by 12 by 12 inches, or if mounted within 4
inches of other heat producing components.
2. These flashers are rated primary - 120 V or 240 V, 60 Hz for motor driving the contracts; Contacts located in neon transformer
secondary rated - 30 mA, 7500/15000 V, 60Hz Maximum. They are for use with secondary midpoint grounded transformers
only.
67
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. These are open-type devices partially enclosed with metal mounting tabs. A suitable enclosure shall be provided in the end use
and the suitability of the bonding means through the mounting means shall be determined in the end use. The suitability of
conduit connections shall be determined in the end use.
4. These components are suitable for use in Dry or Damp Locations.
5. This construction generates ozone. Consideration shall be given to measuring the ozone concentration if used in a sealed
overall enclosure to determine if additional evaluation is needed for the effect of ozone on other sign components. Otherwise it
shall be installed in a ventilated compartment.
Electronic Sign Flasher, Models 101, 101A, 102, 1A2 and 1S2 with or without suffix designation.
1. Temperature testing has been conducted in an enclosure measuring 4 by 5-3/4 by 4-5/8 inches. Consideration shall be given to
conducting a temperature test if installed in a smaller enclosure or if mounted within inches of other heat producing.
2. These flashers are rated 120/240 Vac input with maximum load switching ratings of 15A at 100 cycles per minute, 10A at
switching rate of 250 cycles per minute.
3. These flashers have not been evaluated for DC load ratings.
4. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall be determined in the end use.
5. These components are suitable for use in Dry and Damp Locations.
GREEN LED LIGHTING SOLUTION LLC
SUITE 6G
2800 W SAHARA AVE
LAS VEGAS, NV 89102
E350477
LED Class 2 Strips, Models GL-RGB, GL-101, GL-105.
1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or 15 Volt AC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 30 Volt DC or 15 Volt AC.
3. These Class 2 LED modules are rated as noted in the model list table. When units are connected to a Class 2 circuit, they are
not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated Class 2.
5. These products are not required to be enclosed or protected from the weather in the end product.
Ratings:
Model
LED Strip Length
Number of LEDs
Voltage
Current
Power
GL-RGB
500mm
30
12 Vdc
0.2 A
2.4W
GL-101
500mm
30
24 Vdc
0.3 A
7.2W
GL-101
500mm
30
12 Vdc
0.6 A
7.2W
GL-105
485mm
42
24 Vdc
0.36 A
8.6W
GREEN LED MFG
ROOM B-2
2870 GESSNER DR
HOUSTON, TX 77080
E352678
LED Class 2 Strips, Modules PPL, DPL, OSPL, DPL(W), OSPL(W), DR3, DB3, DG3, DY3, KTR3, DTW3, DTB3, DTR3, WPL(W),
WSPL, NSR3, NSG3, NSB3, NSR3, FPL, KGL, DGL, KR2, KB2, KG2, DR2, DB2, DG2, DDL, KDL(W), DDL(W), KRD2, KBD2,
KGD2, KYD2, DRD2, DBD2, DGD2, DYD2, OSDL(W), OSGL, OSDL, DPL4, DPL40, DPL40(W), OSPL40, OSPL40(W), OSPL4,
FPL40, DOL, DOR, DOB, DOG, DRGB3, WSRGB3, DSL, SSL, KSL(W), DSL(W), DR1, DB1, DG1, NSR, NSG, NSB, DRGB2,
SRGB2, DRGBD, SRGBD, KRGB2, KRGB40, DRGB40, SRGB40, DPL6, OSPL6, GKP, GCP, GOL, GKPW, GR3, GB3, GG3,
GY3, GTW3, GTB3, GWP3, GWR3, GWB3, GWG3, GKD, GSC4, GSPW4, GRC4, GOC3, GOR3, GOB3, GOG3, GRGB3, GW,
RGB3, GKS, GR1, GB1, GG1, GRGB2, GRC6, GOD, GOP, GOC4, GOL4, GOL6, GKSW, GKDW, GCPW, GKPW4, GRGB4,
GRGBP3, GR2, GR4, GB2, GB4, GG2, GG4, GY2, GCW1, GCR1, GCB1, GCG1, GLW1, GLR1, GLB1, GLG1, GWW3, GTR3,
GOW3, GOLC3, GOLW3, GOLR3, GOLB3, GOLG3, G-PCB6, G-PCB8, G-OPCB6, G-OPCB8, G-PCB6-KP1, G-PCBB-KP1, GPCB6-KW1, G-PCB8-KW1, G-RGB8, G-LRGB10, G-PCB R, G-PCB B, G-PCB G, G-PCB-30 W, G-PCB-30 W1, G-PCB-30 R, GPCB-30 B, G-PCB-30 G, G-PCB-57 W, G-PCB-57 W1, G-PCB-57 R, G-PCB-57 B, G-PCB-57 G, G-A/L S30, G-A/L S60, G-A/L
PP30, G-A/L S30 W1, G-A/L S60W1, G-A/L PP30 W1, G-A/L PP60 W1, G-A/L S30R, G-A/L S60R, G-A/L PP30 R, G-A/L PP60 R,
G-A/L S30 B, G-A/L S60 B, G-A/L PP30 B, G-A/L PP60 B, G-A/L S30 G, G-A/L S60 G, G-A/L PP30 G, G-A/L PP60 G, G-A/L RGB
S30, G-A/L RGB S60, G-A/L RGB P30, G-A/L RGB P60.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
GRIMCO INC
1585 FENCORP DR
FENTON, MO 63026
E350828
Class 2 LED Module, Cat. No. H2.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
January 23, 2014
68
SIGN COMPONENTS MANUAL (SAM)
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means.
Structural Panel, non-electrical enclosure rated for use in electric sign components, Cat. No. MAX-Metal, MAX-Metal XL,
and MAX-Metal HD.
1. Illustrate the proper cutting, pointing, installation, component securement and securement to a building surface of a structural
panel.
2. Structural panels have been evaluated for wet location with 50°C ambient.
3. Structural panels may be employed as external decorative faces and are acceptable for support of complete electrical
enclosures, plastic faces, and moldings that are reliably secured to the panel.
4. Structural panels are not suitable to be used as the enclosure of bare live parts or wiring.
5. Nuts and bolts must be used when fastening a ballast or transformer weighing more than 7-1/2 lbs (3.4 kg).
6. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
7. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
GUANGZHOU FANGCUN HONGMEI NEON EQUIPMENT FACTORY
1-3 PANLONG INDUSTRIAL AREA
LONGXI RD LIWAN
GUANGZHOU, GUANGDONG 510378 CHINA
E333976
Class 2 LED Drivers, Model Nos. HMA-60NU-R12, HMA-30NU-R12, HMA-240NU-RX, HMA-200NU-RX, HMA-150NU-RX, HMA120NU-RX, HMA-100NU-RX, HMA-90NU-RX, HMA-60NU-RX, HMA-45NU-RX, HMA-50NU-RX, HMA-350NU-RX, HMA-700NURX, HMA-1050NU-RX, HMA-1400NU-RX, HMA-520NU-RX, HMA-20NU-RX, HMA-15NU-RX, HMA-12NU-RX, HMA-10NU-RX,
HMA-8NU-RX, HMA-6NU-RX, HME-45N-R12, HME-60N-R12, HME-20N-R24, HME-35N-R24, HME-45N-R24, HME-60N-R24,
HMT-YZ-RX, HME-100N-R12, HME-20N-R12, HME-35N-R12.
1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
3. These products shall be enclosed in the end product.
4. These power supplies are suitable for use in dry and damp locations.
5. These devices are intended for factory installation only.
6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
LED Modules, Cat. No. HM-FXXQYZTMMMM series, where XX maybe replaced with the number 12; Q may be replaced with
SMD or FLUX; Y may be replaced with 20 mm, 30 mm 48 mm, 55 mm, 62 mm or 95 mm; Z may be replaced with R, Y, G, W or
RGB, T may be replaced with the numbers 2, 3 and 4.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
GUANGZHOU FUTURE LED CO LTD
THE 4TH FL NO.34
DAYUAN SOUTHERN RD
BAIYUN DISTRICT
GUANGZHOU, GUANGDONG 510540 CHINA
E364415
Class 2 LED modules, Cat. Nos. 5050 LED Module-GS3H, 5050 LED Module-ZS2H, 5050 LED Module-ZS3H, 5050 LED
Module-ZS4H, 5630 LED Module-ZS2P, 5630 LED Module-ZS3P, 5630 LED Module-ZS3H, 3535 LED Module-ZS3P.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Vdc.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
7. The mounting means shall be determined in end use.
GUANGZHOU LINONG LIGHTING TECHNOLOGY CO LTD
KEYING RD
GUANGZHOU SCI-TECH LNDUSTRY PARK
TAIHE TOWN BALYUN DISTRICT
GUANGZHOU, GUANGDONG 510540 CHINA
E362256
Class 2 LED modules, Cat. Nos. LNMS5X2PN46-D12, LNMS5X2PN60-D12, LNMS5X2PF60-D12, LNMS5X3PF81-D12,
LNMS5X3PN81-D12, LNMS5X4PF49-D12, LNMS5X4PN49-D12, LNMS5X2F33-D12, LNMS5X4F35-D12. Where the X may be
69
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
replaced with W, R, G, B, Y or RGB, indicates color temperature.1. These products are only suitable for connection to a Class 2
power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
HATO LIGHTING B V
HANDELSSTRAAT 31
6135 KK SITTARD, THE NETHERLANDS
E356565
Class 2 LED Module, Cat. No. EUL-Fixt-XXXX-XXXX-XX-XXX; "EUL" stands for the productname "EcoUnlimitLED"; "Fixt" stands
for a Fixt-Length; The first four X are Arabic numerals from 200 up to 2800, these indicate the fixt-length in cm; The second four X
are Arabic numerals 4250 (+/-250) or 6500 (+/-500), these indicate the Correlated Color Temperature (CCT) in Kelvin; The two X
indicate the number of segments per side. Any Arabic number from 1 up to 14 segments per side; The last three X are Arabic
numerals and indicate the nominal power of the design.
1. These products shall only be used in an End-enclosure for Dry and Damp Locations Only.
2. These products shall only be connected to a Class 2 power source or LPS power source, rated max. 4.17 Amps, 24 Volt DC
with a maximum power limit of 100 VA.
3. Each model is allowed to contain a maximum of 14 segments, as detailed in the mounting instructions.
4. The suitability of leads shall be evaluated in end product use.
5. The need to perform an input test and a temperature test shall be evaluated in end product use.
HEICO LIGHTING, DIV OF EMD TECHNOLOGIES INC
400 RUE DU PARC
ST EUSTACHE, QC J7R 0A1 CANADA
E301099
LED power supply with Class 2 outputs, Cat. Nos. LMPS-350, LMPS-750 for use with VIRGOLITE LED Modules, Types EC,
EB, MB, MI followed by "+"; VIRGOLITE Types Econo-Brite, Equi-Brite, Mega-Brite, LS2, LS3, LS4, LS6, LS6-70, Mini, clipAled.
1. These power supplies has a single output. The output has been evaluated and found to comply with Class 2 output
requirements.
2. These power supplies are provided with an enclosure that is suitable for installation in a damp or dry location.
3. VIRGOLITE Modules “XXXXX.XXX” must be used with Listed Class 2 Power Supplies, Models LMPS-350 or LMPS-750.
These power supplies are potted.
4. The power supply Models LMPS 750 and LMPS-350 is capable of providing power to maximum number of Virgolite Models.
Virgolite Family
Econo-Brite
Length
(in.)
Max. number of
Modules Per LMPSNumber of LEDs Nominal Voltage Wattage(W) per
350/LMPS 750
per Module
(V)
Module
Power Supplies
3.22
2
3.2
0.26
6
3
3.2
0.41
85/182
2.6
2
3.2
0.26
134/288
3.22
4
3.2
0.55
63/136
6
6
3.2
0.81
43/92
Mega-Brite
3.22
6
3.2
0.81
43/92
6
12
3.2
1.56
22/48
LS2
3.22
2
3.2
.85
42/84
Equi-Brite
134/288
LS3
6
3
3.2
1.25
30/60
LS4
3.22
4
3.2
1.52
23/46
LS6
6
6
3.2
2.1
16/32
LS6-70
6
6
3.2
1.44
25/50
clipAled
1.7
1
3.2
.39
90/192
5. Each power supply shall be installed in accordance with the installation instructions. See ILL. 2.
6. Spacing between adjacent power supplies is 1 in. end to end and 4 in. any other direction or may be used in maximum ambient
temperature of 50C.
Tradename can be "HEICO lighting" or trademark
HENGFU CORP
258 XINJIA RD
SONGJIANG DISTRICT
201611 SHANGHAI, CHINA
E359095
Sign accessories, Models HF60W-SLD-12, HF60W-SLD-24.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted below.
January 23, 2014
70
SIGN COMPONENTS MANUAL (SAM)
Series
Input (V, A)
HF60W-SLD-12
100/120/240,
Loaded Output
(V dc, Ampere)
12, 5
0.79/0.63/0.31
HF60W-SLD-24
100/120/240,
24, 2.5
0.789/0.642/0.313
2. These LED drivers are intended for used in a maximum 20 A branch circuit.
3. These LED Drivers are suitable for use in wet locations.
4. These LED drivers are provided with Listed 18 AWG Input and 16 AWG Output Cord, type SJTW, rated 300 V, 105ºC for
electrical connection, the suitability of the types, wiring and the need for a suitable enclosure shall be determined in each end use
application.
5. These LED drivers are built-in type, fixed wiring connections, intended for used within sign.
6. The metallic housings were not bonded to grounding, the suitability of bonding and grounding shall be determined in each end
use application.
7. These LED drivers are intended for use in the maximum Ta ambient temperature and maximum Tc case (enclosure)
temperature in end products shown as below table.
When the driver with potting: R/C (QMFZ2), DOW CORNING (SHANGHAI) CO LTD (E251343), Cat. No. CN-8760.
Model No.
Tc (Degree, ºC)
Ta (Tested ambient, ºC)
HF60W-SLD-12
80
50
HF60W-SLD-24
85
50
When the driver with potting: R/C (QMFZ2), SHANGHAI JORLE FINE CHEMICAL CO LTD (E315820), Cat. No. ZR340A/B.
Model No.
Tc (Degree, ºC)
Ta (Tested ambient, ºC)
HF60W-SLD-12
80
41
HF60W-SLD-24
85
50
8. Mounting shall be determined in the end-use application.
9. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
10. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
HERA LIGHTING L P
3025 BUSINESS PARK DR
NORCROSS, GA 30071
E357358
CLASS 2/LPS LED Backlight Panel, Model HLP.
1. These LED Backlight panels are only intended for use with a constant voltage LPS/Class 2 output power sources with 12, 24 or
36 Vdc/Maximum 5, 4.16 or 2.77 A output, respectively.
2. When products provided with more than one input connector, there shall be no interconnection of circuits allowed, and each
LPS/Class 2 circuit is separately connected to each LPS/Class 2 power supply. Each input not exceeding 5 A, 4.16 or 2.77 A,
respectively. Power supply with multiple Class 2 outputs may be used.
3. These LED Backlight panels are suitable for use in dry locations only.
4. These LED Backlight panels are not provided with a mounting means. The suitability is to be determined in end product use.
5. These products are to be temperature tested in end product. The maximum temperature on LED board shall not exceed 130°C.
The maximum temperature of supply leads shall not exceed 105°C. The maximum temperature on Light Guide Plate shall not
exceed 50°C.
6. If LPS/Class 2 type LED power sources were provided, the additional consideration should be investigated in the end products.
HIGH PERFECTION TECHNOLOGY CO LTD.
4 ALY 19 LN 379
ZHONGHUA RD
SHULIN DISTRICT
NEW TAIPEI, 238 TAIWAN
E249377
Class 2 LED Power Supply, designated LP1060-Series with numerical suffix -07 through -24, followed by suffix - one or two
letters and - a single letter or number; Model LP2046 followed by suffix - one or two letters and - a single letter or number.
1. All models except for LP2046-YZ-E have a single output that complies with Class 2 output requirements. Model LP2046-YZ-E
has 2 outputs at Class 2 limits.
2. These products are suitable for use in dry damp and wet locations only.
3. The primary sides of these power supplies are suitable for connection with threaded type conduit only.
4. The maximum rated output power for Model LP1060-13-YZ-E, LP1060-17-YZ-E and LP1060-21-YZ-E is 61 watts, for Model
LP1060-24-YZ-E is 60 watts, for Model LP2046-YZ-E is max. 41 watts.
5. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
6. When not marked for dry and damp locations only, the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be
provided with water tight fitting as shown in FIG. 4.
7. When not marked for indoor use only, all models shall have liquid tight fittings on both primary and secondary circuits.
8. When provided with the alternate conduit caps on page 3, the power supply shall be provided with an additional fire enclosure.
9. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
71
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
10. Model LP1060-XX-YZ-E-DV series are provided with a dimming option for use with a 0-10VDC dimming system.
Class 2 LED Power Supply, Cat. No. LP1040-09-Cnnnn, LP1040-10-Cnnnn, LP1040-12-Cnnnn, LP1040-13-Cnnnn, LP1040-15Cnnnn, LP1040-18-Cnnnn, LP1040-22-Cnnnn, LP1040-24-Cnnnn, LP1040-36-Cnnnn, LP1040-48-Cnnnn, LP1040-48C-Cnnnn,
where the suffix "Cnnnn" is optional and nnnn may be any alphanumeric characters.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the
ultimate application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105(C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300
V, 105(C. The suitability of the input and output connections shall be determined in each end use application.
5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be
determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-0 for Models LP1040-09, LP1040-10, LP1040-12, LP1040-13, LP1040-15, LP1040-18, LP-1040-22, and V-2 for
Models LP1040-24, LP1040-36, and the necessity of additional fire barriers shall be determined in end product.
7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
8. The output of the power supply, Model LP1040-48-Cnnnn, exceeds the Class 2 output limits. This shall be considered in the
end product.
Class 2 LED Power Supply, Cat. No. LP1020-10-Cnnnn, LP1020-12-Cnnnn, LP1020-13-Cnnnn, LP1020-15-Cnnnn, LP1020-17Cnnnn, LP1020-18-Cnnnn, LP1020-20-Cnnnn, LP1020-22-Cnnnn, LP1020-24-Cnnnn, LP1020-36-Cnnnn, LP1020-52-Cnnnn,
where the suffix "Cnnnn" is optional and nnnn may be any alphanumeric characters.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. Multiple power supplies shall be spaced at least 25mm (1 in.) end to end or 102mm (4 in.) in other directions. If lesser spacings
are used, then the Temperature Test shall be conducted in the end use product. For reference the maximum enclosure (case)
temperature on the power supply was 90°C when tested at 58.4° ambient.
8. Class 2 Power Supply, Model LP1020-52-Cnnnn are suitable for use in US only.
Class 2 LED Power Supply, Cat. No. LP4240-24-xy, LP4240-15-xy, LP4240-12-xy, LP3240-15-xy and LP3240-24-xy
1. These power supplies have multiple outputs. Power supply Model LP4240-24-xy, LP4240-15-xy and LP4240-12-xy have a
maximum of four Class 2 outputs. Power supply Model LP3240-24-xy has maximum three Class 2 outputs. Each output of
these power supplies have been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
4. When not marked for indoor use only, all units shall be provided with liquid tight fittings on the primary and secondary circuits.
5. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use. C)
Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
Class 2 LED Power Supply, Models LP1025-12, LP1025-24, LP1025-36, LP1025-42, LP1025-50, may be followed by optional
suffix Cnnnn, where nnnn may be any alphanumeric characters.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These lead connected products are suitable for use in commercial application only when marked with 277 V input voltage.
6. These units employ a Class 105 (A) insulation system on Transformer (T1).
Class 2 LED Power Supply, Models LP1017-12-Cnnnn, LP1017-24-Cnnnn and LP1017-36-Cnnnn, where nnnn may be any
alphanumeric characters.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4 When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These products with leads are suitable for use in commercial application only when marked with 277 V input voltage.
Class 2 LED Power Supply, Model LP1090-XX-YZ-E, where XX can be 19, 24 or 36; Y can be G or T; Z can be G or T; and E
can be any number from 170 to 999. ; which may be followed by suffix “DV”.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. Models LP1090-TT-E are suitable for use in dry and damp locations. Models LP1090-GG-E are suitable for use in dry, damp
and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
January 23, 2014
72
SIGN COMPONENTS MANUAL (SAM)
5. When not marked for “Dry and Damp Locations Only” the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be
provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
6. These products are suitable for use in commercial application only when marked with 277 V input voltage.
7. When provided with the alternate conduit caps on page 2A, the power supply shall be provided with an additional fire
enclosure.
8. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
9. Model LP1090-XX-YZ-E-DV series are provided with a dimming option for use with a 0-10VDC dimming system.
HP TEC
100-17, ONSU-DONG, GURO-GU
SEOUL, REPUBLIC OF KOREA
E356485
Class 2 LEDs, designated as SL-XXX Series, where XXX may be replaced with alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 30 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
HUBEI FLEXMEDIA CO LTD
36 SMALL AND MEDIUM-SIZED
ENTERPRISE DISTRICT JIUTONG ROAD
WUJIASHAN DONGXIHU
WUHAN, HUBEI 430040 CHINA
E363474
EL Driver, Non-Class 2, Model PA100.
1. This Drivers have been evaluated to Non-Class 2 output.
2. This Diver has been evaluated using resistive load resulting in the electrical input and output noted below, and the maximum
case temperature shall not exceed 90ºC when used in end product.
Model
PA100
Nominal Input
Nominal Output
V
Hz
A
V ac, Hz
A
W
90-240
50/60
1.8 max
100, 800 Hz
2
80
3. Dry location use only.
4. When used in fixed Sign, spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
5. When used in fixed Sign, this product shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not
less than 4 inches (102mm) apart when arranged otherwise.
6. Do not ground the secondary circuit to the enclosure of this power unit.
HUDNUT CO INC
730 NE 21ST AVE
PORTLAND, OR 97232
E257980
Class 2 LEDs, Cat. Nos. Class 2 LED Strip.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, maximum 30 volt continuous (noninterrupted) DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp, and wet locations.
5. In a wet location, these products are not required to be enclosed or protected from weather.
HYRITE LIGHTING CO
252 S 5TH AVE
CITY OF INDUSTRY, CA 91746
E306782
Class 2 LEDs Cat. Nos. LEDMX-KN Series, where X may be replaced with any letters of alphabet A through Z or blank; K may be
replaced by R, A, Y, B, G or W and N may be replaced with any numbers 0 through 999.
1. These products are only suitable for connection to a Class 2 power source, rated max 15 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Module Cat. Nos. M LEDMX-K series is each rated max. 7.5 Watts per unit. When units are connected to a Class
2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less.
73
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
5. These products are not required to be enclosed or protected from the weather in the end product.
LED power supply with Class 2 outputs, Cat. No. SPS-X0-12, where X is 4, 6 or 9, may be followed by the letter “C”.
1. These power supplies have a maximum of one Class 2 output. However, Model SPS-90-12 has a maximum of two Class 2
outputs. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
5. The suitability of grounding connection shall be determined in the end-use product.
Polymeric Neon Electrodes, End Cap, Models EC-10S-U, EC-18S-U, EC-15S-U, EC-13S-U, and EC-20S-U.
1. These devices are rated max. 7500 V ac to ground. May be used with 15K mid-point grounded transformer.
2. These products are suitable for use in dry or damp locations.
3. These products are required to be enclosed or protected from the weather.
4. As of the September 5, 2008 effective date of UL879, Eighth Edition, all Integral Sleeved GTO cables indicated as suitable for
use with the neon electrode enclosures covered by this report shall have a temperature rating of min. 120(C minimum for dry
locations and min. 135(C for damp locations.
5. These products are only for use in Listed signs and Sections of signs and are not suitable for field installed skeletal neon or
outline lighting.
6. The units shall be subjected to a High Voltage Dielectric Strength test in the end product.
7. These components were evaluated for use with the Listed GTO cables made by Transco Inc (E226224) GTO-15 and Paige
Electric Co L P (E135239), GTO-15, and Hyrite Lighting Co., (E351585), GTO-15-S and GTO-10-S. Use with any other GTO type
or manufacture will need to be evaluated in the end product.
HYUNDAI LED CO LTD
602-6 PALGOGIL-DONG
SANGNOK-GU
ANSAN-SHI, GYEONGGI-DO 426-200 REPUBLIC OF KOREA
E258512
LED Module, Cat. No. BBBX-YZVW Series, where BBB may be any alpha characters from A to ZZZ; X may be any combinations
of alphanumeric characters from A to Z or from 0 to 999; where YZV may be any combination of alphanumeric characters and W
may be blank or any numeric character from 0 to 1.
1. Each Class 2 LED Modules: BBBX-YZVW Series is only suitable for connection to a Class 2 power source, max. 24 Volt dc or
less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. Class 2 LED modules, BBBX-YZVW Series rated max. 12 Watts per LED unit or less. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Module, Cat. Nos. BFL225-YZ12 (F-LED225), BFL235-YZ12 (F-LED235), BFL435-YZ12 (F-LED435), BFL313-YZ12 (FLED313), BFL301-YF12 (RGB301), BFL300c-YF12 (RGB300C), BFL900C-YF12 (RGB900C) and BL05-YF24 (BLO5).
1. These Class 2 LED modules are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. These Class 2 LED modules are rated max. 2 Watts per LED module. When these units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volts or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
I LIGHT TECHNOLOGIES
1093 VOLUNTEER DR
COOKEVILLE, TN 38501
E223028
Class 2 power supplies, Models PN60112DCR-3R, PN10124DCR-3R, PNC224012DCR-3R, PNC224024DCR-3R.
1. These power supplies have been evaluated for use in LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected to
another power source.
5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least
150 mm (6 in) inside.
ICM CORP
P O BOX 2819
SYRACUSE, NY 13220
E109022
Electronic Sign Flasher, Cat. Nos. Cat. No. FPS.
l. When used in an unprotected enclosure, consideration must be given to the environmental conditions to which it will be
subjected.
2. The sign flasher must be mounted on an aluminum heat sink specifically a U-shaped channel with the top 0.04 in thick, and the
sides approx 0.142 in thick. The side rails are 2-11/32 in wide and the top is 2-9/l6 in wide min length is 5-5/l6 in.
3. The terminals are not suitable for field wiring and the connections to the terminals shall be determined in the end use
application.
January 23, 2014
74
SIGN COMPONENTS MANUAL (SAM)
4. This device has not been investigated for loads other than incandescent types.
5. The Temperature Test was conducted in free air. The maximum temperature recorded was 78°C in a 22.6°C ambient. When
provided within enclosure, consideration should be given to performing a Temperature Test.
6. The maximum load switching ratings for these flashers are 8 A at 120 Vac, and shall not be used beyond these ratings or with
DC.
7. These are open-type devices with a metal mounting plate. A suitable enclosure shall be provided in the end use and the
suitability of the bonding means through the mounting means shall
be determined in the end use.
ILIGHT TECHNOLOGIES INC
SUITE 370
118 S CLINTON
CHICAGO, IL 60661
E324738
Class 2 LED Modules, Cat. Nos. “PLEXINEON", "HYPNOTICA iS".
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15V AC or less and 30 volt DC or less
power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
INNOPOL-E CO LTD
555-56 BAEKSEOK-DONG
SEOBUK-GU
CHEONAN-CITY, CHUNGCHEONGNAM-DO
331-979 REPUBLIC OF KOREA
E356129
LED Class 2 Module, Models INP-SCA13, INP-SCA12.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means
INSIGHT LIGHTING CO
4341 FULCRUM WAY
RIO RANCHO, NM 87144
E348871
LED Class 2 Module, Cat. Nos. ILE6, ILE9, ILE12, ILE12(-N), ILE15, ILE3-RGB; Class 2 LED Controller, Cat. No. ILC-V; cat. nos.
may be provided with additional prefixes or suffixes for commercial purposes.
1. These products are only suitable for connection to a Class 2 power source rated 30 Vdc or less.
2. When units are connected to a Class 2/”LPS” circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2/”LPS” supply.
3. These products are suitable for use in dry, damp and wet locations.
4. The suitability of the mounting means shall be determined in the end-use application.
5. LED modules described in this section may be cut into segments per the manufacturer’s installation instructions.
6. Units may be provided with Recognized Component (UYMR2), 3M type VHB double-sided adhesive tape. The tape must be
utilized per the “Conditions of Use” as defined in the Sign Components Manual.
7. A heatsink or a means to draw heat away from the Printed Wiring Board shall be provided in the end-use application.
Diffuser Panels, Cat. Nos. IEP1, IEP2, IEP3, and IEP4.
1. Cat. nos. IEP1, IEP3, IEP4 are suitable for use in dry, damp and wet locations. Cat. no. IEP2 is suitable for use in dry locations
only.
2. The panels are suitable for use as a rigid non-enclosure rated sign body, awning, face or decorative application.
3. Panels have not been investigated for use as an enclosure of live parts, insulating barrier accessibility barrier, connection of
conduit or component mounting or support.
4. Panels are flame class rated HB.
5. Cat. no. IEP1 rated 50°C for clear only when min 1.0 mm thick and rated 90°C for all colors when min 1.5 mm thick.
6. Cat. no. IEP2 rated 50°C for all colors when min 1.5 mm thick.
7. Cat. no. IEP3 rated 90°C for clear only when min 1.5 mm thick.
8. Cat. no. IEP4 rated 80°C for all colors when min 0.75 mm thick and 115°C for all colors when min 1.5 mm thick.
INTERNATIONAL LIGHT TECHNOLOGIES INC
10 TECHNOLOGY DR
PEABODY, MA 01960
E332029
LED Class 2 Module, Model No. designated 1X2, 2X2.
1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory Class 2
power supply.
2. These components have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
75
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical
enclosure.
4. Components are suitable for use in dry, damp and wet locations.
LED Class 2 Module, Cat. Nos. ILT-PC-1X2-[+], ILT-PC-2X2-[+].
[+] - May be any alphanumeric characters to represent color and number of LED per module.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
INTERONE
55-1 DEOKGYE-DONG
YANGJU-SI, GYEONGGI-DO
482-050 REPUBLIC OF KOREA
E349550
LED Class 2 Module, Model Z303, Z301.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
LED Class 2 Module, Z101 K, Z103 K, Z201 K, Z201 S, Z201 T, Z203 K, Z203 SPO, Z203 S, Z203 TPO, Z203 T, Z203 LPO,
Z203 L, Z203 F, Z301 MTPO, Z301 K, Z301 S, Z301 LS, Z301 L, Z301 BB, Z303 K, Z303 SPO, Z303 S, Z303 LSPO, Z303 LS,
Z303 LPO, Z303 L, Z303 FP, Z303 P, Z303 FC, Z303 C, Z303 KF, Z303 F, Z303 BB, Z401 K, Z401 S, Z401 BB, Z403 K, Z403
SPO, Z403 S, Z403 KF, Z403 F, Z403 FP, Z403 P, Z403 FC, Z403 C, Z403 BB, 2P PO, 3P PO, 3P K, STPC, STAL.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
INTERTEK CORP
4TH FL, 81 HSIN TAI-WU RD, SEC 1
HSIN-CHIH, TAIPEI HSIEN 221 TAIWAN
E307120
Class 2 LED Power Supply, Models APP200AC-12, APP200AC-15, APP200AC-24, APP200AC-30.
1. These power supplies have not been provided with a suitable enclosure. In the end product these units shall be enclosed.
2. When used in a cord-connected products, the need for conducting a leakage current test shall be considered in the end
product.
3. The product was tested for use at the maximum ambient temperature (Tma) of 60°C permitted by the manufacturer's
specification. This product will need to be temperature tested in the end product and ambient cannot exceed 60°C.
4. These components are suitable for use in damp locations.
5. The Class 2 output of these power supplies are acceptable for use in a damp location without an additional enclosure. The
Class 2 output of Models APP200AC-12, APP200AC-15 are also acceptable for use in a wet location without an additional
enclosure.
6. These components have been investigated for use on a maximum branch circuit rating of 20A.
Class 2 LED Power Supply, Models APP200AC-48.
1. This power supply has not been provided with a suitable enclosure. In the end product this unit shall be enclosed.
2. When used in a cord-connected products, the need for conducting a leakage current test shall be considered in the end
product.
3. The product was tested for use at the maximum ambient temperature (Tma) of 60°C permitted by the manufacturer's
specification. This product will need to be temperature tested in the end product and ambient cannot exceed 60° C.
4. This component is suitable for use in damp locations.
5. This component has been investigated for use on a maximum branch circuit rating of 20A.
Class 2 LED Power Supply, Models ANP90-12P, ANP90-12PY, ANP90-15P, ANP90-15PY, ANP90-19P, ANP90-19PY, ANP9024P, ANP90-24PY, ANP90-24P1, ANP90-24P1Y, ANP90-30P1, ANP90-30P1Y, ANP240-12P, ANP240-15P, ANP240-19P,
ANP240-24P, ANP155-12AC, ANP155-15AC, ANP155-19AC, ANP155-24AC. These model numbers may or may not be followed
by -277.
1. These power supplies have a maximum of four Class 2 outputs. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary
and secondary circuits.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
76
Class 2 LED Modules, Model Nos. QRN90-15, QRW90-15, QAN90-15, QAW90-15, QGN90-24, QGW90-15, QBN90-24, QBW9024, QWN90-24, QWW90-24, BRN90-15, BRW90-15, BAN90-15, BAW90-15, BGN90-24, BGW90-24, BBN90-24, BBW90-24,
BWN90-24, BWW90-24.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED
power supply or UL Listed or R/C Class 2 Power Supply having continuous DC outputs rated as below in Item 3.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited
to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit.
The following identifies the rating to be used in calculating the maximum number of units per circuit.
LED Cluster
Load Max (mAmps)
Watts
BRxxx-15, BAxxx-15
35 mA
BWxxx-24, BGxxx-24, BBxxx-24
35 mA
0.525 W
0.84 W
QRxxx-15, QAxxx-15
35 mA
0.525 W
QWxxx-24, QGxxx-24, QBxxx-24
35 mA
0.84 W
4. These products are suitable for use in dry, damp and wet locations.
5. The weather enclosure does not require evaluation.
Class 2 LED Modules, Model Nos. Bright Eyes (BEX24-12) BE followed by W, B, G, A or R, followed by 24, followed by 12;
NextGen (ABCD-12) B or T followed by W, B, G, A or R, followed by N or W, followed by 90 or 110; and MiniMod MXW80-12
Series, where X can be A, B, G, R or W
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED
power supply or UL Listed or R/C Class 2 Power Supply having continuous DC outputs rated as below in Item 3.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited
to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit.
The following identifies the rating to be used in calculating the maximum number of units per circuit.
LED Cluster
Load Max (mAmps)
Watts
BEX24-12
400mA per module pair
4.8 W per module pair
ABC90-12
52mA
.62 W
ABC110-12
40mA
.48 W
MiniMod MXW80-12 Series
31 mA
0.372 W
Up to 90 LED clusters may be used when the LED's are ABC90-12.
Up to 110 LED clusters are used when the LED's are ABC110-12.
Up to 160 LED clusters may be used when the LED's are of the MiniMod MXW80-12 Series.
4. These products are suitable for use in dry, damp and wet locations.
5. The weather enclosure does not require evaluation.
Class 2 LED Modules, Model Nos. SLR90-12, SLA90-12, SSR90-12, SSA90-12, SSG90-12, SSB90-12, SSW90-12.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED
power supply or UL Listed or R/C Class 2 Power Supply having continuous DC outputs rated as below in Item 3.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited
to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit.
The following identifies the rating to be used in calculating the maximum number of units per circuit.
LED Cluster
Load Max (mAmps)
Watts
SLR90-12
25mA
.3 W
SLA90-12
25mA
.3 W
SSR90-12
25mA
.3 W
SSA90-12
25mA
.3 W
SSG90-12
25mA
.3 W
SSB90-12
25mA
.3 W
SSW90-12
25mA
.3 W
Up to 200 LED clusters may be used when the LED's are SXX90-12.
4. These products are suitable for use in dry, damp and wet locations.
5. The weather enclosure does not require evaluation.
Class 2 LED Power Supply, Model Nos. LPS12-D1, LPS15-D1, LPS24-D1.
1. This power supply has 1 output. The output has been evaluated and found to comply with Class 2 output requirements.
3. This power supply is provided with a metal enclosure that is suitable for use in wet locations.
4. The output of this power supply is rated 12 V DC, 5 amps, and 60 Watts, 15V, 4A, 60 Watts or 24V DC, 2.5A, 60 Watts.
5. Each power supply shall be installed in accordance with the installation instructions.
Class 2 LED Modules, Model Nos. designated as AOP120XX-Y00Z Series; where XX, Y and Z may be replaced with
alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
77
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Power Supply, Models ANP90-48P, ANP90-48PY, and ANP90-48P1Y, which may be followed by -277.
1. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. When marked for wet location a
junction box is provided on each side for conduit connection. For wet location use, the output leads are to be protected from
contact with water.
2. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
3. When used in wet locations, each unit shall be provided with junction box for use with Listed (QCRV) 1/2 inch, liquid tight conduit
fitting for both primary and secondary circuits.
4. These components shall be installed in compliance with the enclosure and mounting requirements of the ultimate application.
5. The Rain Test was conducted per UL 1310 but the Standing Water Immersion Test was not conducted. When the units are
mounted in a wet location at a height less than 1 foot from the ground surface or on the bottom surface of an exposed
construction where water can accumulate, the need for additional evaluation shall be determined in the end product.
Tradename is "Amperor".
Sign Accessories, Dimmable Power Supplies for LED Modules, Models DIM-240, DIM-240-D, DIM-240-1.
1. These units have been evaluated to Non-Class 2 output.
2. These units have been evaluated using resistive load resulting in the electrical input and output noted below.
Input
Output
Vdc
A
Vdc
A
W
DIM-240,
DIM-240-D
10-48
Max. 5.0
10-48
0-5
Max. 240
DIM-240-1
10-24
Max. 12.5
10-24
0-12.5
Max. 300
Model
3. These units are intended for use in dry locations. Other uses shall be considered in the end product.
4. Spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to
top of enclosure.
5. These products shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less than 4 inches
(102 mm) apart when arranged otherwise.
6. Do not ground the secondary circuit to the enclosure of these units.
7. These units shall be installed in compliance with the enclosure, mounting, grounding, spacing, casualty, and segregation
requirements of the end product application.
8. These units shall be connected behind an power supply, the suitability shall be considered in the end product.
9. The input and output connections of these units are provided with terminal blocks suitable for copper wire size as noted below.
The suitability of input and output connections shall be determined in each end use application.
Input/Output Terminal
Blocks Type
Wire Size, Type
AWG
Torque,
lb-in (Nm)
EXCEL CELL ELECTRONIC CO LTD (E133988),
Type ETB10 series
14-24 AWG,
Sol/Str Wire
2.18
(0.25)
10. Terminals of dimmer were evaluated as isolated non-class 2 type, the suitability shall be considered in the end product.
LED Drivers, Isolated, Non-Class 2 output, Models ANP151-75S1-277, ANP151-110S1-277, ANP151-154S1-277, ANP151220S1-277, ANP151-440S1-277.
1. These units have been evaluated for Non-Class 2 output.
2. These units have been evaluated using resistive load resulting in the electrical input and output noted below, and the maximum
case temperature shall not exceed 90ºC when used in end product.
Model
Input
V
Output
Hz
A (MAX)
V dc
A
W (MAX)
47-63
2.0
75
2.05
154
ANP151-110S1-277
110
1.40
ANP151-154S1-277
154
1.00
ANP151-220S1-277
220
0.70
ANP151-440S1-277
440
0.35
ANP151-75S1-277
100-277
3. These products are intended for dry, damp or wet location use.
4. The lead wire length, routing and splicing shall comply with the requirements of the end-use application.
5. These units are not provided with a mounting means or the means is optional. The method of mounting shall be determined in
the end-use application.
6. These units were tested and found to be acceptable for use in a 60°C ambient temperature. Acceptable operation at a higher
temperature should be determined.
7. The units are intended for factory installed only.
8. The suitability of grounding means shall be determined in the end-use application.
9. An acceptable enclosure shall be provided.
10. When used in fixed Signs, spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
11. When used in fixed Signs, this product shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not
less than 4 inches (102mm) apart when arranged otherwise.
12. Do not ground the secondary circuit to the enclosure of this power unit.
January 23, 2014
78
SIGN COMPONENTS MANUAL (SAM)
INVENTRONICS (HANGZHOU) CO LTD
3 FL NORTH BLDG
368 LIUHE RD
BINJIANG DISTRICT
HANGZHOU, ZHEJIANG 310052 CHINA
E354416
Class 2 power supply, Model EUV-076S012ST-xxxx, where xxxx can be any alphanumeric character or blank.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Max Output (V, A, W)
Model
Input (V, Hz, A, W)
EUV-076S012ST-xxxx
100-277; 50-60; 0.8; 75
12.0; 5.00; 60
3. In the end product, power supply spacing to other heat producing components shall be at least .4 mm (1 in.) from end to end,
and 101.6 mm (4 in.) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products have been tested in oven at min 40ºC ambient, with the maximum case temperature, Tc of 88.7ºC.
7. These products are intended for use in dry or damp locations only.
8. The suitability of input/output leads and the wring shall be determined in end product use.
9. These products are constant voltage type that requires the proper number of LED modules and controllers that do not exceed
the maximum output current.
10. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
11. These LED drivers are intended for use in fixed equipment only.
Class 2 Output power supply, Model EUV-096S024ST-xxxx, where “xxxx” can be any alphanumeric character or blank.
1. These power supplies have been evaluated to Isolated LPS output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Max.
Input
Output
Output
Voltage
Input Freq
Input
Voltage (V
Output
Power
Model No.
(Vac)
(HZ)
Current (A)
dc)
Current (A)
(W)
EUV-096S024ST100-277
50/60
1.2
24
0~4
96
xxxx
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wring shall be determined in end product use.
8. These LED drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does
not exceed the maximum output current.
9. These LED drivers are provided with a multi-conductor AWM wire consisted of two (purple and gray) 22 AWG, min 80°C, min
300 V leads for connecting a dimmer to vary the output current. The connecting diagram is shown as below. The leads are
investigated for use in Class 2 output circuit and cannot be interconnected with the other output of these drivers. The dimmer
may be a 0-10 Vdc input voltage or a 0-300 kohm variable resistor.
Vcc
Vcc
Rin
Rin
1-10 V
INPUT (PURPLE )
1-10V
INPUT (PURPLE )
V 1-10Vdc
Rx (0-300 kohm)
GND (GRAY )
GND (GRAY)
or
IPAN LED INC
SUITE 100
5501 66th Ave
SACRAMENTO, CA 95823
E315810
Class 2 LED Modules, Cat. Nos. LBY-FXXQYZTMMMM series, where XX may be 12, Q may be S or F, Y may be 48 or 78, Z
may be B, G, R, W, Y or RGB, T may be any numerals from 1 to 9 and MMMM may be blank or any alphanumeric characters.
1. These products have been evaluated only for use when connected to the Class 2 output of a Listed or Recognized
Component power source rated 12 V DC.
2. These products are suitable for use in dry, damp and wet locations.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Border Lights LED Modules, Cat. Nos. Cat. No. LBY-D26X144-V series, where X may be B, G, R, W, Y or RGB and V may be
24.
1. These products have been evaluated for use only when connected to the Class 2 output of a Listed or Recognized power
source rated 24 Volts DC.
2. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 V dc or less.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
79
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
Class 2 LED Controller, Cat. Nos. LBY-S3P200W-1.
1. These products have been evaluated for use only when connected to the Class 2 output of a Listed or Recognized
Component power source rated 12 V DC.
2. Class 2 LED Controller, Cat. No.LBY-S3P200W-1 is rated max. 24 Watts. When connected to a Class 2 circuit, these units
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
5. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test
shall be considered.
ITW Plexus / Devcon
30 ENDICOTT ST
DANVERS, MA 01923
E320311
Polymeric Adhesive System, Models AO420 or Composite Welder FS, MA300 or Plastic Welder, MA830 or Metal Welder,
MA205HV, MA420FS Blue, MA420FS Black, MA832GB.
1. These adhesive systems may be used for securement of any combination of surfaces listed in Table A. The end-product
operating temperature is not to exceed the lowest temperature rating of the combination.
2. These adhesive systems are also suitable where exposed to high humidity and occasional exposure to water. The min
temperature rating is -35 C (-31 F).
3. These adhesive systems are suitable for application to smooth flat surfaces, except where another surface configuration is
noted.
4. When considering the use of the adhesive system, the strength of the adhesive joint used to position critical parts shall be
capable of withstanding at least four times the max force in the as-received condition that might be applied to the joint in the
end-product application.
5. The bond strength values shown in Table A were determined in accordance with ASTM D1002, Standard Test Method for
Strength Properties of Adhesives in Shear by Tension Loading.
6. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been
performed. The engineer must consider the need to investigate the part for other than the properties investigated, in accordance
with the applicable end-product standard and/or the requirements outlined in UL 746C, Standard for Material Used in Electrical
Equipment Evaluations.
7. The suitability for the use when exposed to oil, chemicals, refrigerant, soap, X-rays, ultraviolet and the like has not been
determined by this investigation, unless otherwise noted.
8. The average as-received bond strength values are as follows. When determining the suitability of the adhesive system in
accordance with Item 4, the bond strength value should be based on the lowest average as-received bond strength value of the
material combination.
Cat. Nos. AO420 or Composite Welder FS:
Substrate
Max Operating Temp.C (F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
2750.0
AL./SS.
71 (160)
2538.0
AL./Fiber Glass
71 (160)
1794.0
AL./ABS
71 (160)
544.0
SS./SS.
71 (160)
3225.0
SS/Fiber Glass
71 (160)
1981.0
Fiber Glass/Fiber Glass
71 (160)
1044.0
Fiber Glass/ABS Plastic
71 (160)
508.0
Cat. Nos. MA300 or Plastic Welder:
Substrate
Max Operating Temp. C ( F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
2325.0
AL./SS.
71 (160)
2288.0
AL./Fiber Glass
71 (160)
1638.0
SS./SS.
71 (160)
3250.0
SS/Fiber Glass
71 (160)
1244.0
Fiber Glass/Fiber Glass
71 (160)
1106.0
Fiber Glass/ABS plastic
71 (160)
558.0
Cat. Nos. MA830 or Metal Welder:
Substrate
Max Operating Temp. C ( F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
2613.0
AL./SS.
71 (160)
2169.0
AL./Fiber Glass
71 (160)
1369.0
AL./ABS
71 (160)
475.0
SS./SS.
71 (160)
2350.0
SS./Fiber Glass
71 (160)
1531.0
January 23, 2014
80
SIGN COMPONENTS MANUAL (SAM)
SS./ABS
71 (160)
494.0
Fiber Glass/Fiber Glass
71 (160)
963.0
Fiber Glass/ABS Plastic
71 (160)
500.0
Cat. Nos. MA205HV:
Substrate
Max Operating Temp. C (F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
1902.79
AL./SS.
71 (160)
1788.73
AL./Fiber Glass
71 (160)
1442.54
AL./ABS
71 (160)
590.99
SS./SS.
71 (160)
1823.39
Fiber Glass/Fiber Glass
71 (160)
1142.78
Fiber Glass/ABS Plastic
71 (160)
616.40
Cat. Nos. MA420FS Blue:
Substrate
Max Operating Temp. C (F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
1739.64
AL./SS.
71 (160)
1760.05
AL./Fiber Glass
71 (160)
976.14
AL./ABS
71 (160)
618.89
SS./SS.
71 (160)
1788.74
Fiber Glass/Fiber Glass
71 (160)
835.56
Fiber Glass/ABS Plastic
71 (160)
609.46
Cat. Nos. MA420FS Black:
Substrate
Max Operating Temp. C (F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
1636.69
AL./SS.
71 (160)
1766.58
AL./Fiber Glass
71 (160)
1280.51
AL./ABS
71 (160)
507.37
SS./SS.
71 (160)
1965.15
Fiber Glass/Fiber Glass
71 (160)
1025.53
Fiber Glass/ABS Plastic
71 (160)
503.85
Cat. Nos. MA823GB:
Substrate
Max Operating Temp. C (F)
As-Received Bond Strength (PSI)
AL./AL.
71 (160)
1572.20
AL./SS.
71 (160)
1775.92
AL./Fiber Glass
71 (160)
1330.90
AL./ABS
71 (160)
503.09
SS./SS.
71 (160)
1944.19
Fiber Glass/Fiber Glass
71 (160)
1110.47
Fiber Glass/ABS Plastic
71 (160)
509.93
JEWELITE WAGNER ZIP-CHANGE INC
3100 HIRSCH ST.
MELROSE PARK, IL 60160
E90751
Aluminum Reinforced Sign Face Trim, Cat. Nos. Jewelite.
1. The Jewelite trim, bonded to a thermoplastic sign face is not to be considered as providing a weatherproof enclosure, therefore
all internal components shall be suitable for outdoor use or shall be completely enclosed and protected from weathering.
2. The following combination of sign trims bonded to sign faces were subjected to oven, freezing and humidity tests:
Sign Face Generic Material
Solvent
Final Bond Adhesive
Sign Trim Generic Material
Methyl Methacrylate (Acrylic) Weld-On #4 (Methy Chloride) Weld-On #16
Cellulose Acetate Butyrate
(Polycarbonate)
None
Weld-On #55
Cellulose Acetate Butyrate
(Polycarbonate)
None
Weld-On #58
Cellulose Acetate Butyrate
(Polycarbonate)
None
Lord Adhesive #7550 A/C
Cellulose Acetate Butyrate
If any other combination is used, the above mentioned tests should be repeated.
81
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. A 720 h ultraviolet radiation test was conducted on the subject sign trim in order to determine the effects of ultraviolet (UV)
radiation on outdoor signs employing the Jewelite trim. Flammability and electrical characteristics of the cellulose acetate butyrate
sign trim have not been evaluated.
4. The suitability of internal wiring and connections should be evaluated in the end-use application.
5. All metal is painted or plated to provide a means for protection against corrosion.
6. Components that are employed in the end product should be evaluated with respect to suitability of construction, test
performance, electrical rating, mounting and operating temperature.
7. Jewelite is suitable for acrylic and polycarbonate sign faces for indoor or outdoor use. It shall be applied in accordance with the
instructions.
JIANGSU SINO OPTO CO LTD
WENZHUANG RD
YIXING ECONOMIC DEVELOPMENT ZONE
YIXING, JIANGSU 214200 CHINA
E342212
LED Tubes, Cat. No. SN-T.
1. These products are suitable for use in dry, or damp locations.
2. The lamp is maintained not less than 2 inches (50.8 mm) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacing from lampholder to sign housing is zero.
3. This LED lamp is not for use with internally shunted bipin lampholders used with fluorescent instant start lamps.
LED Tubes, Cat. No. SN-T8-4.
1. These products are suitable for use in dry locations.
2. The lamp is maintained not less than 2 inches (50.8 mm) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacing from lampholder to sign housing is zero.
3. This LED lamp is not for use with internally shunted bipin lampholders used with fluorescent instant start lamps.
4. These components are not suitable for use with dimmers.
5. The lamp pins are connected to power supply only at one end, the other end serves as means of mechanical support only.
JIANGYIN HUAHONG ALUBOND METAL INDUSTRIAL CO LTD
70 CHENGLU RD
HUASHI TOWN
JIANGYIN, JIANGSU 210041 CHINA
E353283
Structural Panel, Model Aluminum composite panel.
1. Suitable for use in dry, damp and wet locations.
2. Suitable for use in decorative and sign body applications only.
3. The panel is not suitable for use in component mounting and support applications.
4. Rain tightness shall be determined in the end product.
5. Electrical spacings and bonding for grounding shall comply with the end product standard.
6. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
7. The panel core materials are rated Polyethylene. Consideration will need to be given to end product thermal spacings from heat
producing components or temperature test.
8. These materials are available as unpainted aluminum or pre-painted aluminum.
9. This material has not been investigated for the securement of conduit, electrode housings or the like, suitability shall be
determined in the end product.
10. Not suitable for use in terminating conduit.
11. The panel is rated 75°C. Suitability shall be determined in the end product when subjected to higher than the rated
temperature.
JIANGYIN PIVOT DECORATIVE MATERIALS CO LTD
PIVOT INDUSTRIAL PARK
9TH HUAXI VILLAGE
HUASHI TOWN
JIANGYIN, JIANGSU 214421 CHINA
E341462
Structural Panel, Model Aluminum composite panel.
1. Suitable for use in dry, damp and wet locations.
2. Suitable for use in decorative and sign body applications only.
3. Suitable for use in component support applications. When threaded directly into the panels, screws shall be no smaller/finer than
No 10. Suitability of smaller and/or finer screws shall be determined.
4. Rain tightness shall be determined in the end product.
5. Electrical spacings and bonding for grounding shall comply with the end product standard.
6. Suitable for use in terminating conduit in 1/2 in Trade Size.
7. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support
8. These materials are rated 50∘C, consideration will need to be given to end product thermal spacings from heat producing
components or temperature test.
9. These materials are available as unpainted aluminum or pre-painted aluminum.
JINBO KECHUANG ELECTRONICS CO LTD
343 YANHE RD EAST
XIANGZHOU
E350225
January 23, 2014
82
SIGN COMPONENTS MANUAL (SAM)
ZHUHAI, GUANGDONG 519001 CHINA
Class 2 LED Drivers, Models JLV-12060KA-U and JLV-12030KA-U.
1. The outputs of the units comply with Class 2 criteria of UL 1310 and CSA C22.2 No. 223-M91.
2. The device has been evaluated for dry and damp locations use only.
3. The LED Drivers are provided with 18 AWG input leads and 18 AWG output leads. The suitability of the wiring and the need for
a suitable enclosure shall be considered in the end product.
4. The housings of the LED Drivers do not qualify as Enclosure, and Impact Test has not been conducted. The suitability of the
housing as ultimate enclosure shall be determined in the end use application.
5. Refer to below table for the maximum temperature measured on housing outside surface during the Temperature Test when
shifted to Ambient Temperature 50 C. The necessity of repeated Temperature Test shall be determined in each end use
application.
Models
Maximum temperature measured on housing outside surface
JLV-12060KA-U
73
JLV-12030KA-U
73
6. The LED Drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does not
exceed the maximum output current (or maximum output wattage).
7. A temperature test is not required if the LED drivers are spaced at least 1 in. apart end to end or 4 in. apart in other directions.
Spacng to plastic shall be 1 inch minimum and to metal may be zero in. The need for a temperature test shall be considered if
the LED driver is mounted closer than the referenced spacings. For reference these LED drivers have been tested in a 50 C
ambient and maximum case temperature is 73C.
JKL COMPONENTS CORP
13343 PAXTON ST
PACOIMA, CA 91331
E339601
Class 2 LED Modules, designated as ZAF-336-24, ZAF-486-24, ZAF-636-24, ZAF-936-24, ZAF-1236-24; may be followed by
additional suffixes for color temperature.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 24V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means
LED Illumination Modules, ZM-4047-CW, ZM-1957-CW, ZM-1543-R.
1. Each Class 2 LED Modules is only suitable for connection to a Class 2 power source, max. 24 Volt dc or less. .
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. Class 2 LED modules, rated max. 12 Watts per LED unit or less. When units are connected to a Class 2 circuit, they are not
to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules, Cat. No. ZWF-XXXX-XX, where XXXX-XX will be replaced with alpha-numeric digits that indicated
length and color.
1. These Class 2 LED modules are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. These Class 2 LED modules are rated max. 2 Watts per LED module. When these units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volts or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules, Cat. No. ZWF-337-24CW, ZWF-438-24CW, ZWF-638-24CW, ZWF-939-24CW, ZWF-1239-24CW,
ZWF-337-24WW, ZWF-438-24WW, ZWF-638-24WW, ZWF-939-24WW, ZWF-1239-24WW.
1. Each Class 2 LED Module is only suitable for connection to a Class 2 power source, max. 24 Volt dc or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits.
3. Class 2 LED modules rated max. 12 Watts per LED unit or less. When units are connected to a Class 2 circuit, they are not
to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
JOHNSON WALKER & ASSOCIATES L LC, DBA IMPERIAL PLASTICS MFG
4337 MILL ST
NORTH BRANCH, MI 48461
E225580
Aluminum Reinforced Sign Face Trim, designated Signatrim.
1. Acceptable for use in dry, damp and wet locations.
2. Water exclusion must be determined in the end product.
3. Minimum 5 cm (2 in.) spacing from heat producing components required.
4. The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified adhesives
may be applied for the final bond.
83
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
Sign Face Generic Material
Solvent
Final Bond Adhesive Sign Trim Generic Material
Methyl Methacrylate (Acrylic)
Methylene Chloride Methylene Chloride
Cellulose Acetate Butyrate
Methyl Methacrylate (Acrylic)
Weld-ON #4
Weld-ON # 16
Methylene Chloride
Cellulose Acetate Butyrate
Polycarbonate
Transco
Channel Bond
Cellulose Acetate Butyrate
Transco
Channel Bond
5. The suitability of the securement or “fit” of this trip cap shall be determined in the end product. Screws or solvents are
considered acceptable for permanent mounting.
JS LED TECHNOLOGY CORP, DBA JS LED POWER INC
1318 MAINE AVE
BALDWIN PARK, CA 91706
E308859
Class 2 LED Modules, Cat. No. JE-00ABCD-XY-EZ Series, where A, B, C, D, E, Z, X and Y may be any alphanumeric characters,
or suffixes may be blank.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt AC/DC or less.
2. These products are each rated max. 24 watts per module. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 Power Supply, Cat. Nos. MJ-ABCD-WXYZ Series, where AB is 12, and CD-WXYZ is 20-1670, 40-3300 or 60-5000.
1. These power supplies have a maximum of one Class 2 outputs. The output of these power supplies have been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to
sidewalls, and minimum 2 inches spacing to top of enclosure.
4. These products have not been subjected to Leakage Current, Strain Relief, and Impact Tests. The need to conduct these tests
shall be considered in the product. In addition to these tests, the need to conduct the Mold Stress test on model MJ-1260-500
shall be considered in the end product.
5. These products shall be provided with additional enclosure when used in the end product.
Class 2 LEDs, Cat. Nos. Cat. Nos. JE-001X (HS-F504BR4TN), JE-002X (HS-F504BN4TN), JE-003X (HS-F504BB4TN), JE-004X,
JE-005X (HS-F504BY4TN), JE-006X (HS-R483AR4CY or HS-R484CN4CY or HS-R484CB4CY), where X may be replaced with A,
B, G, M, R or W.
1 These products are only suitable for connection to a Class 2 power source, rated 15 Volt (DC or AC) or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Controllers, Models HM-12RGB5A3-RC, HM-12RGB5A3-XY Series, where suffix X and Y may be any alphanumeric
characters or blank for marketing purpose only.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated max 24VDC.
2. These products are rated per the Table below. When units are connected to a Class 2 circuit, their ratings are to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
Model
Input - Class 2
HM-12RGB5A3-XY Series
Output - Class 2
12 - 24 Vdc
10 – 24 V
24 W
3. These products are suitable for use in dry, and damp.
4. These products are each rated max. 24 watts. When units are connected to a Class 2 circuit, they are not to draw a total
wattage of greater than the secondary or output rating of the Class 2 supply.
Sign accessories, Class 2 LED power supplies, Model MJ-12100.
1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
3. These products shall be enclosed in the end product.
4. These power supplies are suitable for use in dry and damp locations.
5. These devices are intended for factory installation only.
6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
Class 2 Power Supply, Models MJ-1220, MJ-1240 and MJ-1260.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Model Number
Input Voltage (V) Input Current (A) Frequency (Hz) Output Voltage (Vdc) Output Current (mA)
MJ-1260
110~240, 277
1
50/60
12
500
MJ-1240
110~240
1
50/60
12
3.3
MJ-1220
110~240
1
50/60
12
1.67
January 23, 2014
84
SIGN COMPONENTS MANUAL (SAM)
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end-to-end,
and 101.6 mm (4 in.) from side-to-side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in a dry or damp locations only.
7. The suitability of input/output leads and the wiring shall be determined in end product use.
8. Model MJ-1260 shall be subjected to a temperature test in the end product and the maximum enclosure temperature is not to
exceed 79.4°C for this power supply.
9. Models MJ-1220 and model MJ-1240 shall be subjected to a temperature test in the end product and the maximum enclosure
temperature is not to exceed 84°C for these power supplies.
LED drivers, isolated output, Models MJ-1230, MJ-2430, MJ-2460, MJ-12100L, MJ-24100L, MJ-12150, MJ-12200, MJ-24200,
MJ-60-5000-CN, MJ-60-5000-ON, MJ-60-5000-OJ, MJ-60-2500-CN, MJ-60-2500-ON, MJ-60-2500-OJ, MJ-60-1250-CN, MJ-601250-ON, MJ-60-1250-OJ, MJ-30-2500, MJ-30-1250 and MJ-30-0625.
1. These products are provided with the following electrical ratings:
Model No.
Input
Voltage
(Vac)
Input
Freq
(HZ)
Input
Nominal
Current Output
(A)
Voltage
(V dc)
MJ-1230
100-240
50/60
0.7
12
2.5
MJ-2430
100-240
50/60
0.7
24
1.25
MJ-2460
100-240
50/60
1.4
24
2.5
MJ-12100L
100-240
50/60
1.4
12
8.4
MJ-24100L
100-240
50/60
1.4
24
4.2
MJ-12150
110-240
50/60
2
48
3.125
MJ-12200
100-240
50/60
2.8
12
16.5
MJ-24200
100-240
2.8
24
8.4
MJ-60-5000-CN, MJ-60-5000-ON, MJ-60-5000-OJ
100-277
50/60
0.73
5-12
5
MJ-60-2500-CN, MJ-60-2500-ON, MJ-60-2500-OJ
100-277
50/60
0.70
14-24
2.5
1.25
Nominal
Output
Current
(A)
MJ-60-1250-CN, MJ-60-1250-ON, MJ-60-1250-OJ
100-277
50/60
0.69
34-48
MJ-30-2500
100-277
50/60
0.35
5-12
2.5
MJ-30-1250
100-277
50/60
0.35
17-24
1.25
MJ-30-0625
100-277
50/60
0.35
39-48
0.625
2. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end-to-end,
and 101.6 mm (4 in.) from side-to-side.
3. These products shall be enclosed in the end product.
4. These products are suitable for factory wiring only.
5. These products are intended for use in a dry or damp locations only.
6. The suitability of input/output leads and the wring shall be determined in end product use.
7. Models MJ-60-5000-CN, MJ-60-2500-CN, MJ-60-1250-CN, MJ-60-5000-ON, MJ-60-2500-ON and MJ-60-1250-ON shall be
subjected to a temperature test in the end product, where the maximum enclosure temperature is not to exceed 67.9°C.
8. The load powered by these products shall be enclosed in the end product applications.
JUSTIN INC
2663 N LEE AVE
SOUTH EL MONTE, CA 91733
E235322
Class 2 Power Supply, Model 601-12DC, 601-12DCR, 101-24DCR, C2240-12DCR, C2240-24DCR, C2240-12, C2240-12-240,
C2240-24, and C2240-24-240.
1. These power supplies have been evaluated for use in LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected
to another power source.
5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at
least 150 mm (6 in) inside.
Class 2 Power Supply, Model 601-12DC-LC, 601-12DCR-LC, 101-24DCR-LC, C2240-12DCR-LC, C2240-24DCR-LC, C2240-12LC, C2240-12-240-LC, C2240-24-LC, and C2240-24-240-LC.
1. These power supplies have been evaluated for use in portable LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected
to another power source.
5. The attachment plug on the end of the power supply cord is not to be removed.
KASON INDUSTRIES INC
57 AMLAJACK BLVD
NEWNAN, GA 30265
Power supplies with Class 2 output circuits, Model 61815000200.
E363080
85
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105(C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300
V, 105°C. The suitability of the input and output connections shall be determined in each end use application.
5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be
determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
unit is V-2 and the necessity of additional fire barriers shall be determined in end product.
7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
8. The output of the power supply exceeds the Class 2 output limits. This shall be considered in the end product.
KBJ SIGN INC
1800 W ADAMS BLVD
LOS ANGELES, CA 90018
E350092
Class 2 LED Modules, KPL, FPL, KR3.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Class 2 Module, KBJ-301, KBJ-303, KBJ-301-S, KBJ-303-S, KBJ-3RGB, KBJ-401, KBJ-403-S, KBJ-4RGB.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
KEYSTONE TECHNOLOGIES LLC
PO BOX 246
AMBLER, PA 19002
E356111
Class 2 LED Modules, Models KTLD-80-1-24V, KTLD-60-1-12V, KTLD-60-1-24V, KTLD-60-1-24V-SC, KTLD-60-UV-24V, KTLD60-UV-24V-SC, KTLD-60-UV-24V-DIW, KTLD-60-UV-1214V, KTLD-60-UV-1214V-SC, KTLD-60-1-24V-W2, KTLD-60-UV-24VW2, KTLD-60-UV-12V-W2, KTLD-100-UV-24V-66-AP2, KTLD-24-1-12V-AK1.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1.
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below:
Model
4.
Ta (°C)
KTLD-80-1-24V
40
KTLD-60-1-12V
40
KTLD-60-1-24V
40
KTLD-60-1-24V-SC
40
KTLD-60-UV-24V
40
KTLD-60-UV-24V-SC
40
KTLD-60-UV-24V-DIW
52
KTLD-60-UV-1214V
40
KTLD-60-UV-1214V-SC
40
These LED drivers are intended for use in dry and damp locations except that models KTLD-60-UV-1214V and KTLD-60-UV1214V-SC are suitable for dry location only.
5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a
suitable enclosure shall be considered in the end product.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. The need of the grounding means shall be determined in the end product.
8. These LED drivers shall be enclosed within a suitable end product enclosure.
9. For model KTLD-60-UV-24V-DIW, the conduit knockout test was not conducted. The suitability is to be determined in end
product.
10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
11. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
LED drivers, Models KTLD-10-1N-12V-F3, KTLD-10-1N-24V-F3, KTLD-12-1-350-FDIM-AF1, KTLD-24-1-24V-AK1, KTLD-24-UV12V-AK1, KTLD-24-UV-24V-AK1, KTLD-150-UV-24V-66-AP3, KTLD-60-UV-12V-66-AP4, KTLD-60-UV-24V-66-AP4, KTLD-100UV-24V, KTLD-100-UV-12V
1. These LED drivers have been evaluated using resistive load.
January 23, 2014
86
SIGN COMPONENTS MANUAL (SAM)
2. These products have been evaluated with the following characteristics.
Model No.
Input type
Output is
Intended
Location
Connection
Ta, °C.
Input
Output
KTLD-10-1N-12V-F3
[X] Branch Circuit
(Mains)
[X] Isolated
[X] Class 2
Damp
60
AWM
Leads
AWM
Leads
KTLD-10-1N-24V-F3
[X] Branch Circuit
(Mains
[X] Isolated
[X] Class 2
Damp
60
AWM
Leads
AWM
Leads
KTLD-150-UV-24V-66-AP3
[X] Branch Circuit
(Mains)
[X] Isolated
[X] Non-Class 2
Wet
60
SJTW
Cord
SJTW
Cord
KTLD-60-UV-12V-66-AP4
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
Wet
60
AWM
Leads
SJTW
Cord
[X] Branch Circuit
(Mains)
[X] Isolated
[X] Class 2
Wet
60
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains
[X] Isolated
[X] Class 2
Damp
40
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains
[X] Isolated
[X] Non-Class 2
Damp
40
AWM
Leads
AWM
Leads
KTLD-12-1-350-FDIM-AF1
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
KTLD-24-1-24V-AK1
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
KTLD-60-UV-24V-66-AP4
KTLD-100-UV-24V
KTLD-100-UV-12V
KTLD-24-UV-24V-AK1
KTLD-24-UV-12V-AK1
[X]
5. The suitability of the input/output connection and the wiring in a suitable enclosure is also to be considered in end product use.
6. These products are intended for building in or mounted on the surface of end product. Acceptability of the LED driver with
respect to mounting, spacing, casualty, temperature and segregation are to be determined as part of the end device evaluation.
7. The suitability of grounding means shall be determined in the end-use product for models KTLD-10-1N-12V-F3, KTLD-10-1N24V-F3, KTLD-100-UV-24V, KTLD-100-UV-12V, KTLD-24-1-24V-AK1, KTLD-24-UV-12V-AK1, KTLD-24-UV-24V-AK1.
8. For models KTLD-10-1N-12V-F3, KTLD-10-1N-24V-F3, KTLD-12-1-350-FDIM-AF1, the suitability of the driver enclosure as final
enclosure shall be evaluated in end product.
9. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure. Otherwise, temperature test shall be conducted.
10. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise. Otherwise, temperature test shall be conducted.
KOLEDO INTERNATIONAL BV
EKKERSRIJT 7051
5692 HB SON EN BREUGEL, THE NETHERLANDS
E346915
LED Light Strings, LED Strings Series 12NC - "Affinium High Powered LED Light Strings", Part Nos. 9290 004 61903, 9290 004
62103, 9290 004 62203, 9290 004 62303, 9290 004 62403. .
1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory Class 2
power source, rated 30V DC or less.
2. These components have not been evaluated for use and connection to a power source supply with outputs parameters
exceeding the limitations for a Class 2 circuit.
3. Class 2 LED Strings when connected to a Class 2 source, are not to draw a total current or wattage of greater than the
secondary or output rating of the Class 2 circuit.
4. These components are suitable for use in Dry, Damp, and wet locations and are not and are not required to be enclosed or
protected from the weather in the end product when connected to Class 2 source of supply with 30 V DC or less maximum
voltage.
5. These products described in this section may be cut into segments per manufacture’s installation instructions.
LED Posterbox modules, Models LPM8W6300K325mm (12.8")300, LPM13W6300K565mm (22.2")300, LPM8W6300K565mm
(22.2")300, LPM6W6300K325mm (12.8")300, LPM8W4000K325mm(12.8")330, LPM13W4000K565mm(22.2")300 or Alternate
Catalog Numbers: 9290 004 834, 9290 004 835, 9290 004 836, 9290 004 837, 9290 006 007, 9290 006 008. Models LPM6300K
371mm 4leds 400, LPM6300K 565mm 6leds 400, LPM2700K 371mm 4leds 400, LPM2700K 565mm 6leds 400, LPM4000K
371mm 4leds 400, LPM4000K 565mm 6leds 400, LPM6500K 371mm 4leds 400, LPM6500K 565mm 6leds 400 or Alternate
Catalog Numbers: K929483613, K929483713, K929600513, K929600613, K929600913, K929601013, K929483913, K929484013.
1. The LED’s were evaluated for connection to a UL Recognized Component Sign Accessory - UYMR2, Class 2, 24 VDC
maximum output power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. The suitability of the mounting means shall be determined in the end use product evaluation.
87
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4. Suitable grounding is considered necessary for sign application and shall be evaluated in the end use product evaluation.
5. The product is suitable for use in dry, damp and wet locations.
6. Spacing between LED posterbox modules are not specified.
LAMINATORS INC
3255 PENN AVE
HATFIELD, PA 19440
E60612
Structural panels, consisting of a plywood or plastic core, faced on both sides with sheet metal, Types CPA, S2S.
1. The structural panel may be employed as external decorative faces and for the support of complete electrical enclosures.
2. The structural panels shall not be used to enclose bare live parts or wiring; such parts shall be enclosed in a wireway complying
with the Standard for Electric Signs.
3. The complete enclosure, plastic faces, and moldings may rely upon the structural panels for support. These components are to
be reliably secured to the panel and if sheet metal screws are employed, they shall not strip when tested as described in
Paragraph 57 of the Standard for Electric Signs (UL 48).
4. All exposed edges of these panels including drilled holes, etc. shall be treated with two coats of asphalt based paint or a R/C
Sign Accessory (UYMR2) wood coating.
5. The metal faces shall be grounded in accordance with the Standard for Electric Signs (UL 48). Separate grounding straps shall
be used when necessary.
6. Acceptable for use in dry, damp and wet locations
7. Limited to only decorative and sign body applications
8. Water exclusion must be determined in the end product
9. Minimum 5 cm (2 in) spacing from heat producing components required
10. Suitable for use in terminating conduit
11. Not suitable for the support of components weighing more than 7.5lbs (3.4 kg).
Structural panels, Types Omega-Bond 2mm, Omega-Bond 3mm, Omega-Bond 4mm, Omega-Bond 6mm.
1. This product is intended as an outer decorative covering, has not been investigated for use as an electrical enclosure.
2. Structural panels may be employed as external decorative faces and are acceptable for support of complete electrical
enclosures, plastic faces, and moldings that are reliably secured to the panel.
3. This product is acceptable for use in dry, damp and wet locations
4. The water exclusion must be determined in the end product.
5. Suitable for use in component support applications. When threaded directly into the panels, suitability of screws shall be
determined in the end product.
6. Nuts and bolts must be used when fastening a ballast or transformer weighting more than 7-1/2 lbs (3.4 kg).
7. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
8. These materials are rated Polyethylene. Consideration will need to be given to end product thermal spacings from heat
producing components or temperature test.
9. These materials are available as unpainted aluminum or pre-painted aluminum.
10. This material has not been investigated for the securement of conduit, electrode housings or the like, suitability shall be
determined in the end product.
11. These panels shall be attached with screws, bolts or rivets to the structural framework so as to cause bonding to both
conductive surfaces to ground, and to adequately secure each panel in place.
LANE TECHNICAL SALES INC
6465 N AVONDALE AVE
CHICAGO, IL 60631
E319901
Class 2 LEDs, Models LTS-UL-LLHID-12WW-SMD, LTS-UL-LLHID-24WW-SMD, LTS-UL-HID-xx, LTS-UL-WHID-xx, LTS-ULHID30-xx, LTS-UL-WHID30-xx, LTS-UL-ID-xx, LTS-UL-TWF2-xx; "xx" suffix is a representation for any color.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED strips, Models SC-ID-W-24V, SC-XID-3020-W, SC-XID1-3528-XX, LTS-UL-XID-3528-XX, SC-W1XID1-3528-XX24V, where "XX" suffix is a representation for any color.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED ERA LLC
SUITE 100
2685 LANGFORD RD
NORCROSS, GA 30071
E365373
January 23, 2014
88
SIGN COMPONENTS MANUAL (SAM)
Sign accessories, Class 2 led modules, Z201 T, Z201 S, Z203 T, Z203 S, Z301 MTPO, Z301 S, Z303 S, Z301 LS, Z303 LS,
Z301 L, Z303 L, Z301 BB, Z303 KF, Z303F, Z303P, Z303 FP, Z401 S, Z403 S, Z403 F, Z403 C, STPC, STAL.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
LED FOR YOU CO LTD
359-4 DAESSANGNYEONG-RI
CHOWOL-EUP
GWANGJU-SI, KYUNGGI-DO REPUBLIC OF KOREA 1
E345929
Class 2 LED Module, Models LFU-2SW, LFU-2SR, LFU-2SG, LFU-2SB, LFUC-2SW, LFUC-2SR, LFUC-2SG, LFUC-2SB, LFUH2SW, LFUH-2SR, LFUH-2SG, LFUH-2SB, LFU-2SC, LFUC-2SC, LFUH-2SC, LFU-3SW, LFU-3SR, LFU-3SG, LFU-3SB, LFUC3SW, LFUC-3SR, LFUC-3SG, LFUC-3SB, LFUH-3SW, LFUH-3SR, LFUH-3SG, LFUH-3SB, LFU-3SWW, LFUC-3SWW, LFUH3SWW, LFUP-3SW, LFUPC-3SW, LFUPH-3SW, LFUPH-3SWC, LFU-3SC, LFUC-3SC, LFUH-3SC, LFU-3SWC, LFUC-3SWC,
LFUH-3SWC, LFUP-3SWC, LFUPC-3SWC, LFU-4SW, LFU-4SR, LFU-4SG, LFU-4SB, LFUC-4SW, LFUC-4SR, LFUC-4SG,
LFUC-4SB, LFUH-4SW, LFUH-4SR, LFUH-4SG, LFUH-4SB, LFU-4SC, LFUC-4SC, LFUH-4SC.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED INC
#22 1601 FAIRVIEW DR
CARSON CITY, NV 89701
E255480
LED Illumination Modules, Cat. No. Series 04021-XXXX and 04022-XXXX, where XXXX can be 2000, 4000, 5000, 6000 or 9000
1. These products are only suitable for connection to a
Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with
Class 2 voltage and energy limits and which is rated greater than 15 V.
3. Class 2 LEDs, Series 04021-XXXX and 04022-XXXX are each rated max. 1.2 Watts per unit. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Illumination Modules, "1 Watt High Power LED Module", Model designation 04024-XXXX, where XXXX is any number
combination.
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. Class 2 LEDs, “1 Watt High Power LED Module”, model designation 04024-9000 is each rated max. 3.0 Watts per unit. When
units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of
the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Illumination Modules, Cat. Nos. 04022-8800, 04025-XXXX series, where XXXX is any number combination..
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. Class 2 LED modules, Cat. No.04022-XXXX and Cat. No. 4025-XXXX are each rated max. 1.2 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Illumination Modules, Cat. No. 04026-XXXX Series, where XXXX is any number combination.
1. These products are only suitable for connection to a Class 2 power source rated 15 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Flexible LED Modules, Cat. No. 06031-XXXX series and Ribbon Led lighting Cat. No. 06050-xxxx, where XXXX is any number
combination.
89
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. Class 2 LED modules, Cat. No. 06050-XXXX series are each rated max50 Watts per unit. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Module designated "RGB Border Lite".
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 15 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Module Models 04007-1000 and 04007-6000.
1. These products are only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated max 12 VDC.
2. These products are rated per the Table below. When the units are connected to the Class 2 supply, their loads are to be limited
to draw a total power or current of no greater than the output power or current rating of the Class 2 power supply.
Max. Input – Class 2
Each Output – Class 2
Number of
Model
Outputs
Vdc
Max. Vdc
Max. VA
04007-1000
12
12
36
3
04007-6000
12
12
24
3
3. These products are suitable for use in dry and damp locations.
4. These drivers are provided with a max. of 3, Class 2 outputs.
5. These products are suitable for factory wiring only.
6. These products shall be enclosed in the end product.
LED KINGDOM INC
SUITE 102
3701 N JOHN YOUNG PKY
ORLANDO, FL 32804
E364597
Class 2 LED Modules, Cat. Nos. PT-2D-XXVN, VL-3D-XXVN, DM-3D-XXCP, XX may be any alphanumeric character to indicate
LED color.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. For M601C series, three units are consisted one module.
7. The suitability of supply leads shall be determined in end use.
Class 2 LED Modules, Cat. Nos. BY-5D-XXCL, BY-3D-XXCL, XX may be any alphanumeric character to indicate LED color.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
Class 2 LED Modules, Cat. Nos. NC-3D-XXCL, PA-BB-CCDD-XX, XX may be any alphanumeric character to indicate LED color
and BB may be replaced with any numeric character from 0 to 9 or any alpha characters combination from A to Z, which indicates
product LED quantity, CC may be replaced with any alpha characters combination from A to Z, which indicates LED color.
DD may be replaced with any alpha characters combination from A to Z, indicates product LED encapsulation types.
XX may be blank or any numeric character from 0 to 1 or any alpha characters combination from A to Z, indicates product
generation.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
LED Drivers, Class 2, Models EVE-30-12, EVE-30-24.
1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. The products are intended to be built-in, the suitability of enclosure, mounting, input / output connections shall be considered in
the end product.
4. The products are intended for use in damp and wet locations.
5. These products are to be used in maximum ambient temperature (Ta) and Maximum case temperature (Tc) are as below :
January 23, 2014
90
SIGN COMPONENTS MANUAL (SAM)
Wet location
Damp location
Ta
Tc
Ta
Tc
EVE-30-12
40
-70
85
EVE-30-24
40
-70
85
6. These LED drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does
not exceed the maximum output current.
7. These products are suitable for factory wiring only.
8. These products have been evaluated using a resistive load resulting in a maximum input and output.
9. The products are intended to be connected to a maximum 20 A branch circuit.
10. Humidity and Rain tests have been conducted for reference only. The need to repeat these tests shall be considered when
mounted in the end-product.
11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Drivers, isolated, non-Class 2, Models EVE-60-12A, EVE-60-24A, EVE-100-12A, EVE-100-24A, EVE-150-12A, EVE-15024A.
1. These units have an isolated Non-Class 2 output.
2. The products are intended for built-in, the suitability of enclosure, mounting, input / output connections shall be considered in the
end product.
4. These products are suitable for use in damp and wet locations.
5. These products are to be used in maximum ambient temperature (Ta) and Maximum case temperature (Tc) are as below :
Wet location
Damp location
Models
Ta
Tc
Ta
Tc
EVE-60-12A
40
-70
85
EVE-60-24A
40
-70
85
EVE-100-12A
40
-65
85
EVE-100-24A
40
-65
85
EVE-150-12A
40
-50
75
EVE-150-24A
40
-50
75
6. The LED drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does not
exceed the maximum output current.
7. These products are provided with Input and Output cord. The grounding continuity shall be checked in end product.
8. These products are suitable for factory wiring only.
9. The product has been evaluated as isolated output rated non-Class 2 using a resistive load resulting in a maximum input and
output.
10. These products are intended to be connected to a maximum 20 A branch circuit.
11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Drivers, isolated, Class 2, Models EVE-60-12, EVE-60-24, EVE-100-12, EVE-100-24.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Models
Model Number
Input Voltage
(V)
Input Current
(A)
Frequency
(Hz)
Output Voltage
(Vdc)
Output Current
(mA)
EVE-60-12
100-240
0.78
50/60
12
5
EVE-60-24
100-240
0.78
50/60
24
2.5
EVE-100-12
100-240
1.25
50/60
12
3.9 #
EVE-100-24
100-240
1.25
50/60
24
4.0
# - Two outputs: Each 12 Vdc, 3.9 A.
3. In the end product the power supply spacing to other power supplies shall be at least 25.4 mm (1 in.) from end-to-end, and
101.6 mm (4 in.) from side-to-side. When spaced closer, a temperature test is required.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in dry, damp or wet locations.
7. The suitability of input/output leads and the wiring shall be determined in end product use.
8. These products are provided with 18 AWG stranded, rated minimum 300 Vac, minimum 60 C (for wet location), minimum 105 C
(for damp and dry location), for input and output connections. Acceptability of the leads relative to strain relief and secureness, is
to be determined as part of the end device evaluation. The grounding continuity shall be checked in end product
LED LIGHTING ENGINEERING & DESIGN CORP
100 CAT CAY CT
ATLANTA, GA 30350
E329665
Class 2 LED module, Model Cat. No. VECLA.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
91
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. These products are each rated max. 3.6 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LEDING SOLID STATE LIGHTING LTD
47B SANJIANG INDUSTRY
DONGGUAN, GUANGDONG 523460 CHINA
E357006
Class 2 LED modules, Cat. No. MXX-XXX-XX-XX-XXX series; The first X can be any one of the Arabic numerals of 1-9, these
indicate LED quantity; The second X can be any letter in alphabet, represent for beam angel; The third X is for the supplier of the
lamp; The fourth X is for the model of the lamp; The fifth X can be any one of alphanumeric characters; The sixth and seventh X is
for the color; The eighth and ninth X is for the product versions; The last three X are for the input voltage, 12V represent the input
voltage is 12VDC, 15V represent the input voltage is 15VDC.
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. (For model MXX-XXX-XXXX-15V)
2. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less. (For model MXX-XXX-XXXX-12V)
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
4. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
5. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Vdc or less. (For model
MXX-XXX-XX-XX-15V)
6. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less. (For model
MXX-XXX-XX-XX-12V)
7. These products are not required to be enclosed or protected from the weather in the end product.
8. The suitability of supply leads shall be determined in end use.
LEDSTORE INTERNATIONAL CORP
11TH FL-16
NO 888 JING GUO RD
TAOYUAN, 330 TAIWAN
E341676
CLASS 2/LPS LED Backlight Panel, Model 48-48-A, 48-48-M.
1. These LED Backlight panels are only intended for use with a constant voltage LPS/Class 2 output power sources with 12, 24 or
36 Vdc/Maximum 5, 4.16 or 2.77 A output, respectively.
2. When products provided with more than one input connector, there shall be no interconnection of circuits allowed, and each
LPS/Class 2 circuit is separately connected to each LPS/Class 2 power supply. Each input not exceeding 5 A, 4.16 or 2.77 A,
respectively. Power supply with multiple Class 2 outputs may be used.
3. Model 48-48-A is suitable for use in dry locations only, Model 48-48-M is suitable for use in damp locations.
4. These LED Backlight panels are not provided with a mounting means. The suitability is to be determined in end product use.
5. These products are to be temperature tested in end product. The maximum temperature on LED board shall not exceed 130°C.
The maximum temperature of supply leads shall not exceed 105°C. The maximum temperature on Light Guide Plate shall not
exceed 50°C.
6. If LPS/Class 2 type LED power sources were provided, the additional consideration should be investigated in the end products.
LEOTEK ELECTRONICS CORP
50 LUNG-YUAN 7TH RD.
LUNG-TAN
TAOYUAN HSIEN, TAIWAN
E321017
Power Supply with Class 2 outputs, Models LP1090-19-YZ-E, LP1090-24-YZ-E, LP1090-36-YZ-E.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. Models LP1090-TT-E are suitable for use in dry and damp locations. Models LP1090-GG-E are suitable for use in dry, damp
and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
5. When not marked for “Dry and Damp Locations Only” the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be
provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
6. These products are suitable for use in commercial application only when marked with 277 V input voltage.
7. When provided with the alternate conduit caps on page 2A, the power supply shall be provided with an additional fire
enclosure.
8. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
9. Model LP1090-XX-YZ-E-DV series are provided with a dimming option for use with a 0-10VDC dimming system.
Power Supply with Class 2 outputs, Models LP4240-24-XY, LP4240-15-XY, LP4240-12-XY, LP3240-24-XY, LP3240-15-XY.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
92
1. These power supplies have multiple outputs. Power supply Model LP4240-24-xy, LP4240-15-xy and LP4240-12-xy have a
maximum of four Class 2 outputs. Power supply Models LP3240-15-xy and LP3240-24-xy has maximum three Class 2
outputs. Each output of these power supplies have been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 2 inches.
4. When not marked for dry and damp locations only, all units shall be provided with liquid tight fittings on the primary and
secondary circuits.
5. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
Class 2 LED Power Supply, Models LP1025-12, LP1025-24, and LP1025-36; may be followed by optional suffix Cnnnn, where
nnnn may be any alphanumeric characters.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
5. These lead connected products are suitable for use in commercial application only when marked with 277 V input voltage.
6. These units employ a Class 130 (B) insulation system on Transformer (T1).
Class 2 LED Power Supply, Models LP1017-12-Cnnnn, LP1017-24-Cnnnn and LP1017-36-Cnnnn, where nnnn may be any
alphanumeric characters, and LP1090-XX-YZ-E, where XX can be 19, 24 or 36; Y can be G or T; Z can be G or T; and E can be
any number from 170 to 999.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These products with leads are suitable for use in commercial application only when marked with 277 V input voltage.
Class 2 LED Power Supply, Cat. No. LP1020-10-Cnnnn, LP1020-12-Cnnnn, LP1020-15-Cnnnn, LP1020-18-Cnnnn, LP1020-22Cnnnn, LP1020-24-Cnnnn and LP1020-36-Cnnnn, where the optional suffix "Cnnnn" may be any alphanumeric character.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) or Class 130 (B) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief on input lead construction and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-0, and the necessity of additional fire barriers shall be determined in end product.
7. Multiple power supplies shall be spaced at least 25mm (1 in.) end to end or 102mm (4 in.) in other directions. If lesser spacings
are used, then the Temperature Test shall be conducted in the end use product. For reference the maximum enclosure (case)
temperature on the power supply was 90°C when tested at 58.4°C ambient.
Class 2 LED Power Supply, Cat. No. LP1040-09-Cnnnn, LP1040-10-Cnnnn, LP1040-12-Cnnnn, LP1040-13-Cnnnn, LP1040-15Cnnnn, LP1040-18-Cnnnn, LP1040-22-Cnnnn, LP1040-24-Cnnnn and LP1040-36-Cnnnn. where "Cnnnn" could be defined as any
alphanumeric characters for marketing purpose, or blank.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the
ultimate application.
2. These units are provided with a Class 105(A) or Class 130 (B) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1,
300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be
determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-0 and the necessity of additional fire barriers shall be determined in end product.
7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 LED Power Supply, Cat. No. LP1060-Series with numerical suffix –07 through 24 followed by suffix - one or two letters
and - a single letter or number, and Model LP2046 followed by suffix – one or two letters and - a single letter or number.
1. These power supplies have a single output that complies with Class 2 output requirements.
2. These products are suitable for use in dry damp and wet locations only.
3. The primary sides of these power supplies are suitable for connection with threaded type conduit only.
4. The maximum rated output power for Model LP1060-13-YZ-E, LP1060-17-YZ-E and LP1060-21-YZ-E is 61 watts, for Model
LP1060-24-YZ-E is 60 watts.
5. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
6. When not marked for indoor use only the power supply primary bracket shall be provided with min. 3.5 threads and tapered for
connection to liquid tight conduit fitting.
7. When not marked for indoor use only, all models shall have liquid tight fittings on both primary and secondary circuits.
8. When provided with the alternate conduit caps on page 3, the power supply shall be provided with an additional fire enclosure.
93
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
9. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
10. Model LP1060-XX-YZ-E-DV series are provided with a dimming option for use with a 0-10VDC dimming system.
Class 2 LED Power Supply, Cat. No. LP4240-24-xy, LP4240-15-xy, LP4240-12-xy, LP3240-15-xy and LP3240-24-xy
1. These power supplies have multiple outputs. Power supply Model LP4240-24-xy, LP4240-15-xy and LP4240-12-xy have a
maximum of four Class 2 outputs. Power supply Models LP3240-15-xy and LP3240-24-xy has maximum three Class 2
outputs. Each output of these power supplies have been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls
and top of enclosure is kept at minimum 2 inches.
4. When not marked for dry and damp locations only, all units shall be provided with liquid tight fittings on the primary and
secondary circuits.
5. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
LEOTEK ELECTRONICS USA CORP
726 S HILLVIEW DR
MILIPITAS, CA 95035
E232725
Class 2 LED Channel Lite, Cat. Nos. CLM-XXR, E, Y, G, B or W, followed by –RW or -RD where XX represents 01 to 100 strings
of LED modules.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED “Channel Lite”, CLM-XXR, E, Y, G, B, or W followed by -RW, module is rated 0.3 Watts per module. When
modules are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of
the Class 2 supply per Class 2 circuit.
4. LM-XXR, E, Y, G, B, or W followed by -RW, modules are provided with wire soldered on the printed wiring board for connection.
5. These products are suitable for use in dry, damp and wet locations. These products are not required to be enclosed or
protected from weather.
Class 2 LED Tubes, Cat. Nos. "BTL-96X-PAX" Series, where "X" may be replaced by B, G, W, R, E and Y.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 volt DC power source or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
4. These products are provided with wire soldered on the printed wiring board for connection.
5. These products are suitable for use in dry, damp and wet locations when provided with housing for Class 2 LEDs.
Class 2 LED Modules, Cat. No. "PEM-XXX" Series, where XXX is any alpha-numeric combination denoting LED color, type, or
number of modules.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component – Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Class 2 LED Modules, Model BTS-600W-BMW.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 25 volt DC power source or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
4. These products are provided with wire soldered on the printed wiring board for connection.
5. These products are suitable for use in dry, damp and wet locations when provided with housing for Class 2 LED modules.
Class 2 LED Modules, Models CLM-RDP-XX, CLM-RDP2-XX and CLM-RMP2-XX series, where XX may be any alphanumeric
characters.
1. These products are only suitable for connection to a Class 2 power source rated 15 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 15 V DC.
3. These products are each rated max. 75 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Modules, Models "Lite-Stik", CLX-YZAB series, where X, Y, Z, A and B may be any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
January 23, 2014
94
SIGN COMPONENTS MANUAL (SAM)
3. These products are each rated max. 48 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Modules, designated as “Cooler Light” CL5-AABBXYZ Series, where AA can be a combination of any alphanumeric
characters from 1 to 6, or A to Z; BB may be any numeric characters from 01 to 36; X may be any letter A to Z; and YZ may be a
combination of any alphanumeric characters from 1 to 9, or A to Z.
1. These products are only suitable for connection to a Class 2 power source rated 60 Volt DC or less.
2. When these products are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
3. These products are suitable for use in dry and damp locations with supply sources rated at 60 Volts DC or less.
4. These products are rated as the following:
Input Voltage (Vac or
Input Constant Current
Model Designation
Input Frequency (Hz)
dc)
(A)
“Cooler Light” CL5-AABBXYZ Series
60
0.7
60
5. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
LEYARD OPTOELECTRONIC CO LTD
9 ZHENG HONG QI W ST
HAIDIAN DISTRICT
100000 BEIJING, CHINA
E326659
Class 2 LED Modules, Model IV.
1. Acceptability for multiple connections (daisy chaining) not exceeding 16 A on a single branch circuit shall be determined by the
end product requirements.
2. This product was tested for use at a room ambient temperature of 25°C. Testing was conducted with the unit in a test box with
dimensions that were 2 inches from the nearest projection on the sides and 12 inches from the top and bottom. The need for
conducting temperature testing in the end product shall be considered where the units are installed in a higher ambient.
3. The unit is provided with four threaded nipple at the corner of the housing and provided with two hooks on the top. The suitability
of the mounting means shall be determined in the end use.
4. The Rain Test per UL 879 was performed only on the face of the LED sign with the back sealed for testing located right below
the screws along the perimeter of the back housing of the LED modules. Suitability for outdoor use when installed in the overall
sign construction shall be considered in the end product evaluation.
5. The Abnormal Tests (Component Fault and Locked Fan) were performed on the product. Consideration for performing additional
fault testing shall be determined in the end product.
6. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
Class 2 LED Modules, Model MESH.
1. Acceptability for multiple connections (daisy chaining) not exceeding 12 A (based on 14AWG power supply cord) on a single
branch circuit shall be determined by the end product requirements.
2. This product was tested for use at a room ambient temperature of 25°C. The need for conducting temperature testing in the end
product shall be considered where the units are installed in a higher ambient.
3. The suitability of the mounting means shall be determined in the end use.
4. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
5. This product should be mounted 4 feet above the ground, if not, Sprinkler test should be considered.
6. The suitability of SJTW power supply cord needs to be determined in the end use.
Class 2 LED Modules, Model NV.
1. Acceptability for multiple connections (daisy chaining) not exceeding 12 A (based on 14 AWG power supply cord) on a single
branch circuit shall be determined by the end product requirements.
2. This product was tested for use at a room ambient temperature of 40°C. The need for conducting temperature testing in the end
product shall be considered where the units are installed in a higher ambient.
3. The suitability of the mounting means shall be determined in the end use.
4. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
5. This product should be mounted 4 feet above the ground, if not, Sprinkler test should be considered.
6. The suitability of power cord needs to be determined in the end use.
Class 2 LED Modules, Model TV.
1. Acceptability for multiple connections (daisy chaining) not exceeding 12 A (based on 14 AWG power supply cord) on a single
branch circuit shall be determined by the end product requirements.
2. This product was tested for use at a room ambient temperature of 40°C. The need for conducting temperature testing in the end
product shall be considered where the units are installed in a higher ambient.
3. The suitability of the mounting means shall be determined in the end use.
4. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
5. The suitability of power cord needs to be determined in the end use.
LED drivers, isolated, non-class 2 output, Models LDP-LY175W1A*G, LDP-LY350W1A*G.
1. These LED Drivers have been evaluated to Non-Class 2 output.
2. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted below, and the
maximum case temperature shall not exceed 90ºC when used in end product.
Model
Nominal Input
V
Hz
Nominal Output
A
V dc
A
W
95
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
LDP-LY175W1A*G
175-240
50/60
1.5
4.2
35
175
LDP-LY350W1A*G
175-240
50/60
2.5
4.5
70
350
3. These LED drivers are intended to be used in fixed signs only.
4. These products are intended for use in dry and damp location.
5. These products are not provided with input/output wire but connectors. The suitability of the wiring and connector using shall be
considered in the end product.
6. These products should be mounted inside suitable enclosure of end products.
7. These LED drivers are of constant voltage type that requires the proper number of LED modules and controllers that does not
exceed the maximum output current.
8. The suitability of grounding connection shall be determined in the end-use product.
9. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
10. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LIGHT BEAM INDUSTRIES LLC
SUITE B
2877 CHAD DR
EUGENE, OR 97408
E464618
Class 2 Component, designated as Model LBP Series.
1. These products are only suitable for connection to a Class 2 power source rated 24 V DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. These products are suitable for use in dry and damp locations with supply sources rated at 24 V DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
7. When provided with more than one input connector, there shall be no interconnection of circuits allowed, and each Class 2
circuit is separately connected to each Class 2 power supply.
8. A minimum spacing of 6.4 mm (1/4 inch) shall be maintained between circuits in the assembled lamp panel.
LIGHT ENGINE LTD
6TH FL, PHOTONICS CENTER
2 SCIENCE PARK EAST AVE
HONG KONG SCIENCE PARK
SHATIN, HONG KONG
E329864
LED Light Cube, Cat. No. LCB-3x3-18-7-LM1 Series.
1. These products are only suitable for connection to a Class 2 power source rated max. 60 V DC or less for indoor applications
and rated max 30V dc or less for outdoor applications.
2. When units are connected to a Class 2/”LPS” circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2/”LPS” supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products described in this section may be cut into segments per manufacturer’s installation instructions.
5. The LED Light Cube has not been evaluated as enclosure, sign face, or diffuser. Suitability shall be determined in the end use
product.
6. When these products are used in applications other than signs or
Outline lighting, the need to conduct a temperature test shall be considered.
7. These Class 2 LED modules are only suitable for use in Canada, when marked with Class 2 input voltage of less than 42.4 V
DC rating.
8. Spacings between low voltage wiring and uninsulated live parts of the
LED Light Cube and any line voltage in the end product shall comply with the Spacing requirements in the end use application.
LIGHT SOURCE SOLUTIONS LLC
8830 GLASGOW POINTE
DULUTH, GA 30097
E353792
Sign accessories, Class 2 LED Modules: LSS-H-4, LSS-H-3, LSS-H-3S, LSS-H-2, LSS-H-2S, LSS-H-1, LSS-E-4, LSS-V-4, LSSE-3, LSS-V-3, LSS-E-3S, LSS-V-3S, LSS-E-2, LSS-V-2, LSS-E-2S, LSS-V-2S, LSS-E-1, LSS-V-1.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means.
LIGHTBOARD TECHNOLOGIES LLC
E345255
January 23, 2014
96
SIGN COMPONENTS MANUAL (SAM)
SUITE 117
8700 W 36TH ST
ST LOUIS PARK, MN 55426
Class 2 LED Modules, designated as DVXS-YYK Series, where D may be any numeral from 1 to 12; X may be 1 or 2; YY may be
any numeric characters and TVXPYYKZZ Series where T may be any numeral from 1 to 24; X may be 1 or 2; YY and ZZ may be
any numeric characters.
1. The LED modules designated as DVXS-YYK Series are only suitable for connection to a Class 2 power source rated 12 Volt DC
or less.
2. The LED modules designated as TVXPYYKZZ Series are only suitable for connection to a Class 2 power source rated 24 Volt
DC or less.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp or wet locations.
5. These products may be secured in place in the end product by any means available.
Sign accessories, LED Arrays, designated as LightBoard 120V-10.10 Series.
1. These products are provided with the following electrical ratings:
Product Series
Max. Input Voltage (V)
Max. Input Current (A)
LightBoard 120V-10.10
120
60mA
2. These products are suitable for use in dry and damp locations.
3. These products shall be installed in accordance with the manufacturer's instructions.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches to sidewalls, and
minimum 2 inches spacing to top of enclosure.
5. These products are suitable for factory wiring only.
6. These products shall be enclosed in suitable electrical enclosure in the end product.
7. The suitability of input leads and the wring shall be determined in end product use.
8. The proper grounding means of this product shall comply with the end product requirements.
9. In the end product the Dielectric Voltage Withstand test need to be conducted between the live parts and dead-metal parts,
including the enclosure.
10. Cover/Diffuser - When provided the cover shall be R/C (UYMR2/8), Sign Accessory Rigid sign face material designated
Makrolon Sheet.
11. The mounting means of these products shall be determined in the end product.
12. The connector of this product has not been tested for interrupting the flow of current by connecting or disconnecting the mating
connector. The connector should be used only where it will not interrupt the flow of current.
LED system, designated as 24V1PYY5KZZ Series, where YY may be any numerals and ZZ may be 12 or 18.
1. These products are suitable for use in dry, damp or wet locations.
2. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top or sides of enclosure.
3. When applicable, the suitability of the enclosure, mounting means, grounding, supply lead wires and the electrical connection to
the products shall be determined in the end product.
4. All circuits of these systems beyond the power supplies are powered by a Class 2 source.
5. These products are provided with the following input electrical ratings:
Supply (V)
Frequency (Hz)
Current (A)
100-277
47-63
3
6. When used in wet locations, each power supply unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings for
both the primary and secondary circuits.
Sign accessories, controller, designated as "Class 2 Controller".
1. These components should be installed in accordance with the manufacturer's instructions.
2. These products are suitable for use in dry and damp locations.
3. These products are provided with the following electrical ratings:
Model
Class 2 Controller
Max. Input
(Class 2)
Max. Output
(Class 2)
Voltage
(VDC)
Current (A)
Voltage
(VDC)
Current (A)
24
4
24
3
4. The need to conduct a ground continuity test shall be considered in the end product.
5. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
6. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
7. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
8. These products are not provided with an enclosure. The need for an enclosure shall be determined in the end product
application.
LINKCOM MFG CO LTD
5TH FL
127 LANE 235 POU-CHOU RD
HSIN TIEN, TAIPEI HSIEN 231 TAIWAN
Power supplies, isolated LPS output, Models LCVE-060W125-XXXX, LCVE-060W240-XXXX.
1. These products are provided with the following electrical ratings:
E360042
97
SIGN COMPONENTS MANUAL (SAM)
Model No.
Input
Voltage
(V)
Input
Input
Output
Frequenc
Curren
Voltage
y (HZ)
t (A)
(V dc)
Output
Output
Curre
Power
nt (A)
(W)
LCVE-060W125- 100-277
XXXX
50-60
1
12
5
60
LCVE-060W240- 100-277
XXXX
50-60
1
24
2.5
60
January 23, 2014
2. The power supplies had been considered ambient 45 degree C for Model LCVE-060W125-XXXX and 55 degree C for Model
LCVE-060W240-XXXX. If operated at a higher ambient temperature, it should be determined in end product.
3. The suitability of Electrical/Fire/Mechanical enclosure shall be determined in the end product.
4. The load powered by the Isolated LPS output of the power supplies are suitable for use in dry and damp locations.
5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
6. In the end product, power supplies shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
7. The power supplies shall be installed in compliance with the enclosure, mounting, spacing, casualty, and segregation
requirements of the end product application.
8. The suitability of input and output leads shall be determined in end product.
LITECORR INTERNATIONAL CO LTD
NO 96 LANE 690 D
TONGLI RD
JIUTING SONGJIANG
201615 SHANGHAI, CHINA
E353861
Class 2 LED Module, Cat. No. EZ MAXI LED.
1. This product is only suitable for connection to a Class 2 power source, rated 2.8~3.5 Volt DC or less for model EZ MAXI LED.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than electrical ratings.
3. This Class 2 LED module is rated as noted in the electrical ratings tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. This product is suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. This product is not required to be enclosed or protected from the weather in the end product.
6. This product may be secured in place in the end products by any means available.
LORD CORPORATION
2000 W GRANDVIEW BLVD
ERIE, PA 16514
E225855
Acrylic adhesives, Lord 201/19, -403/19, -406/19, -406/19 Red, -410/19.
1. The use of these adhesive systems shall be employed in an applications wherein the limitations as set forth in Table A are not
exceeded.
2. These systems may be used for securement to any combination of surfaces listed in Table A, provided the use temperature is
no higher than the lowest temperature rating of any element of the combination.
3. These systems are also suitable for use outdoors where exposed to high humidity or water. The minimum temperature rating
is -35°C (-31°F).
4. These systems are suitable for application to smooth flat surfaces prepared in accordance with adhesive manufactures
instructions. The need for adhesive bond strength test when applied to another surface or configuration shall be determined in
the particular end use application.
5. The materials have been evaluated for adhesive compatibility and stability only. Adhesive shall be applied in continuous bead
when used as water seal.
6. Means need to be provided for grounding metal parts that may become energized.
7. When considering the use of these adhesives, one square inch of surface covered by adhesive can support in shear tension
the weight specified below.
TABLE A
Max. Temp.
2
Adhesive
Substrates
°C
lbs/in.
403/19, 406/19,
Aluminum,
130
472
406/19 Red, 410/19 Stainless steel,
Cold Rolled steel
201/19
Aluminum
110
615
Urethane adhesive, Lord 7542A/D, -7542A/B, -7542A/C, -7542A/E.
1. The use of these adhesive systems shall be employed in applications wherein the limitations, as set forth in Table A, are not
exceeded.
2. These systems may be used for securement to any combination of surfaces listed in Table A, provided the use temperature is
no higher than the lowest temperature rating of any element of the combination.
3. These systems are suitable for application to smooth flat surfaces prepared in accordance with adhesive manufactures
instructions. The need for adhesive bond strength test when applied to another surface or configuration shall be determined in
the particular end use application.
4. The materials have been evaluated for adhesive compatibility and stability only. Adhesive shall be applied in continuous bead
when used as water seal.
5. Means need to be provided for grounding metal parts that may become energized.
January 23, 2014
98
SIGN COMPONENTS MANUAL (SAM)
6. When considering the use of any adhesive covered by this Report. One square inch of surface covered by adhesive can
support in shear tension the weight specified below.
TABLE A
2
Adhesive
Substrates
Max. Temp. °C
lbs/in.
7542A/D, 7542A/B, 7542A/C, 7542A/E
Polyphenylene oxide (PPO) thermoplastic
90
191
LOUISVILLE LAMP CO
3316 GILMORE INDUSTRIAL BLVD
LOUISVILLE, KY 40213
E348495
Class 2 LED Module, Models NA00 and NEA0.
1. The suitability of the mounting means shall be determined.
2. These products are suitable for use in dry, damp and wet location.
3. The LED Modules are intended for connection to a Class 2 power source, rated 12 Volt DC.
4. These products are rated as the following:
No. of LED per Module
Max. Wattage per LED
Module
Voltage (V dc)
Total Constant Current (A)
NA00
54
5W
12
0.5
NEA0
306
23 W
12
2
Model
5. Model NEA0 was evaluated based on being connected to a source of supply only by solder leads and have not been evaluated for
supply connections made by any type of connector.
6. The suitability of the diffuser to serve as a barrier or enclosure shall be determined in the end use product. Consideration for
addressing electrical, flammability, and mechanical properties shall be given.
LOUISVILLE LAMP CO
3316 GILMORE INDUSTRIAL BLVD
LOUISVILLE, KY 40213
E352989
Class 2 LED light board, Models LB-3624A, LB-3624B, LB-3624C.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limited circuit and which is rated greater than 12 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the
Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
7. These products cannot be wired in series.
LUCKY VALLEY TECHNOLOGY (SHENZHEN) CO LTD
NORTHERN DIST OF SCIENCE & TECH PARK
3 QIONG YU RD, 1 WORKSHOP, 6RT
NAN SHAN DISTRICT
SHENZHEN, GUANGDONG 518000 CHINA
E347782
Class 2 Output LED Driver, Model RG180-W3V012SD0.
1. The output (Red/Black) of each unit complies with Class 2 criteria of UL 1310.
2. The device is provided with 18 AWG input and output leads. The suitability of input and output connections shall be determined
in end-use application.
3. The suitability of grounding means shall be determined by end product.
4. The device is not intended for field wiring used.
5. The device is intended to be connected to a maximum 20 A branch circuit.
6. The devices are of the constant current type that requires the proper number of LED modules and controllers that does not
exceed the maximum output voltage/current.
7. The measured maximum external enclosure temperature (Tc) is 77.2 degree C when the room ambient temperature are 60
degree C. The suitability shall be determined in end application.
8. The devices employ input surge suppression protection, Cat. No. S14K385E2K1 under UL File E321126, which is intended
end-use SPD type 2. The suppressed voltage rating is 385 Vac. The suitability of use of this component shall be determined
in the end-product application.
9. No mechanical test has been conducted for the models and the metal chassis is considered as dead metal. The devices shall
be mounted in the intended manner in an enclosure, having adequate strength and thickness with acceptable spacing being
provided.
10. The device has been evaluated for dry and damp locations use only.
11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LUCKYSTAR ELECTRONIC TECHNOLOGY CO LTD
10 FUSHENG RD HECHENG ST
GAOMING DISTRICT
E320022
99
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
FOSHAN, GUANGDONG 528500 CHINA
LED Modules, Models LS0723x, LS0766x, LS0769x, LS0776x, LS0782x, LS0783x, and LS-KM02-x where that x may be R, G, B,
Y, CW, WW, P or O indicating LED Color.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Modules, Models LS0766HD, LS0791R and LS0791H.
1. These products are only suitable for connection to the output of a Class 2 power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. The LED modules are rated as noted in the electrical ratings table. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end products by any means available.
Class 2 LED modules, designated as LSXXXX-YY series, where XXXX and YY may be combinations of any numbers.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Modules, Models LS-0767, LS-MZ0609, LS-MZ0612-2 and LS-MZ0612-3.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LUMIFICIENT CORP
8752 MONTICELLO LN NORTH
MAPLE GROVE, MN 55369
E230262
Class 2 LED Modules, HRL-06-PFC-96, HRL-08-PFC-96-BMA, HRL-xx-PFC-96yy, where xx denotes 06 original model or 07
Alternate constructions, where yy denotes BM for the use of the CBI circuit breaker Model No. (BFQ1PA-B07XC-0500X), Class 2
Power Unit. Model HYPERION R-Lite System-LED tape. Model HLR-PC power connector. Model HRL-IDC Power IDC connector.
1. The power units were submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40(C.
2. The HRL-06-PFC-96 power unit is provided with a conduit fitting suitable for 1/2 in. Trade Size rigid nonmetallic conduit.
3. The HRL-06-PFC-96 power unit, HRL-xx-PFC-96yy and HRL-08-PFC-96BMA, HYPERION R-Lite System-LED tape, HLR-PC
power connector, and HRL-IDC Power IDC connector are suitable for dry or damp locations
4. Temperature test at 40(C, Inputs and Dielectric test was conducted. The need for additional test shall be determined in the end
used product.
5. The Model HRL-08-PFC-96BMA power unit is provided with a 1/2 in. Trade Size conduit opening.
Class 2 LED modules Model HYPERION R-Lite System-LED tape, Model HLR-PC power connector, & Model HRL-IDC Power
IDC connector.
1. The power units were submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C.
2. The HRL-06-PFC-96 power unit is provided with a conduit fitting suitable for 1/2 in. Trade Size rigid nonmetallic conduit.
3. The HRL-06-PFC-96 power unit, HRL-xx-PFC-96yy and HRL-08-PFC-96BMA, HYPERION R-Lite System-LED tape, HLR-PC200 power connector, HRL-JC-200 jumper connector and HRL-IDC-B Power IDC connector are suitable for dry or damp
locations
4. Temperature test at 40C, Inputs and Dielectric test was conducted. The need for additional test shall be determined in the end
used product.
5. The Model HRL-08-PFC-96BMA power unit is provided with a 1/2 in. Trade Size conduit opening.
LED Driver; Cat. No. Model HRL-06-PFC-24, HRL-xx-PFC-24yy where xx denotes 06 original model or 07 Alternate
constructions, where yy denotes BM for the use of the CBI circuit breaker Model No. (BFQ1PA-B07XC-0500X), Class 2 Power
Unit.
1. The HRL-06-PFC-24 power unit was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of
40(C.
2. The HRL-06-PFC-24 power unit is intended for installation inside an electrical enclosure. Minimum spacing between adjacent
power units is 4 in.
3. The HRL-06-PFC-24 power unit is suitable for dry or damp locations.
Class 2 LED module, designated as Hyperion R2, Cat. No. HR2-XXXX, where XXXX may be replaced with any alphanumeric
characters.
1. These products are only suitable for connection to a LPS or Class 2 power source rated 24 Volt AC or less.
January 23, 2014
100
SIGN COMPONENTS MANUAL (SAM)
2. These products are each rated max. 2.4 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are suitable for use in dry and damp locations with supply sources rated at 24 Volts AC or less.
4. These products may be secured in place in the end product by any means available.
Class 2 LED Modules, designated as H-Lite-XXXX series, E-Lite-XXXX series, E-Lite-YYY series, where XXXX may be any
numeric characters and YYY may be any alpha characters.
1. These products are only suitable for connection to a Class 2 power source rated 8 Volts AC or DC or less.
2. When units are connected to a Class 2 circuit, these products are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp or wet locations.
5. These products may be secured in place in the end product by any means available.
Sign Accessories, Transformer, Class 2 Inherently limited, Model HRL-PSLP-13 and Transformers Class 2 Non-Inherently limited
Models HRL-PS277-70, HRL-PS96-70, and HRL-PSSQ-25-T.
1. These LED Transformers have been evaluated to Class 2 output requirements for AC circuits with a maximum of two Class 2
output.
2. These products are provided with the following electrical ratings:
Input Volt
HZ
Amps
Max.
Input
Watts
V(ac)
Current A
VA/Output
HRL-PSLP-13
120
50/60
0.175
21
8.3
2.0
17
(1)
HRL-PS277-70
277
50/60
0.347
94
8.5
5.0
42.5
(2)
HRL-PS96-70
120/
240
120/240
50/60
0.786/
0.401
.293/.1468
94
8.5
5.0
42.5
(2)
35
8.5
3.5
30
(1)
Model
HRL-PSSQ-25-T
50/60
# of Output
3. The suitability of any mounting means shall be determined in the end use product.
4. The secondary windings were evaluated independently and were found in compliance with the Class 2 Non-Inherently limited
parameters. Therefore, the secondary windings and the associated circuits shall not to be interconnected in the end-use
application.
5. The transformer leads have not been subjected to the Strain Relief Test. The need for conducting this test shall be considered
in the end-use application.
6. These LED Transformers are suitable for use in dry and damp locations only.
7. These products shall be enclosed in the end product.
8. These products are only suitable for factory wiring.
9. Model HRL-PS277-70 and HRL-PS96-70 shall be wired as follows:
Terminal Blocks Cat. Nos.
MPT410 by ASSEL EUROCLAMP
Wire Range
AWG-CU.
Sol/Str.
Screw Torque InLbs.
CA
Min. 18
4.5
For factory wiring only
10. All tests for model HRL-PSSQ-25-T were conducted in the intended metallic end product enclosure. The Rated Output Heating
Test for model HRL-PSSQ-25-T was tested in a 50 ambient chamber.
LUMINII CORP
6264 OAKTON ST
MORTON GROVE, IL 60053
E362622
Class 2 Power Supply, Models PSD-288-24, PSD-288-24-277.
1. These power supplies have been evaluated for use in LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected to
another power source.
5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least
150 mm (6 in) inside.
LUMIRON INC
# A-33
20725 NE 16TH AVE.
MIAMI, FL 33179
E242758
Class 2 LEDs, Cat. No. Models Series LM, LMG, LMP, LMR, LMS, LMT. May have additional suffixes.
1. These modules have been evaluated for use on a UL Listed or Recognized Class 2 power source rated 12 V DC or 24Vdc.
2. The suitability of supply sources other than Class 2 has not been evaluated and shall be determined in the end-product.
Special consideration shall be given to the enclosure and spacing requirements in UL48.
3. These modules are suitable for use in dry, damp or wet locations. They are not required to be enclosed or protected from
weather.
4. The total wattage drawn by all modules connected to a single Class 2 supply shall not exceed the rated capacity of that supply.
LUNERA LIGHTING INC
SUITE 100
2041 MISSION COLLEGE BLVD
E348779
101
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
SANTA CLARA, CA 95054
Class 2 LED Panel, GLB Series.
1. These products are only suitable for connection to the output of a Class 2 Power Supply rated 24VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the below Table. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
Operating
Current per
Watts per
Voltage
module
module
LED quantity
Part No.
Size
( V DC )
(A)
(W)
(pc)
GLBXXXX-XXXX-XXX
May Vary
24
2.5
60
May Vary
4. These products are suitable for use in dry and damp locations without additional enclosures.
LVC CONNECTORS INC
6068 METROPOLITAIN E
MONTREAL, QC H1S 1A9 CANADA
E339231
PVC Tube, Models LVC-3 and TK-24-XXX.
1. These products are only suitable for protecting listed Class 2 wiring that are supplied by power supplies that are marked as
having a Class 2 output or LPS.
2. For outside wall use only.
3. Not suitable for inside walls.
4. These products may be secured in place in the end product by any means available.
Class 2 Low Voltage Connectors, Model LVC2, LVC4, SNAP-KONEK III, and STICK-KONEK.
1. These devices are not suitable for interrupting the flow of current by connecting or disconnecting.
2. These products are only suitable for connection to a Class 2 power source, Class 2 supply rated max. 15 Volts AC or max. 30
Volts DC or less.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. Modules can be installed to interconnect leads in the field or pre-installed.
7. These products may be secured in place in the end product by mechanical securement or double sided adhesive tape.
8. For Model LVC2 and LVC4, suitable for connecting stranded wires which are 18, 20 or 22 AWG with compatible wire guide
inserts.
9. For Model SNAP-KONEK III, suitable for connecting single conductor per channel either AWM wires 18-24 AWG, or PowerLimited Circuit Cables type CL3P, CL3R, CL3, CL3X, CL2P, CL2R, CL2, CL2X and PLTC.
10. The Model STICK-KONEK base and button are used to join LED strips, LED bars, or LED leads wires.
MAGTECH INDUSTRIES CORP
5625-A S ARVILLE ST
LAS VEGAS, NV 89118
E314969
Class 2 LED Module, Cat. No. LP12060P-08, LP12060P-09, LP12060P-10, LP12060P-11,LP12060P-12, LP24060P-22,
LP24060P-23,LP24060P-24.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both
primary and secondary circuits.
MATRIX FRAME
FLEVOWEG 27
2318 BZ LEIDEN, THE NETHERLANDS
E351057
Class 2 LED Module, "Lightbox CREE XP LEDstrip".
1. These products are suitable for use in Dry and Damp Locations Only and may only be supplied with a Class 2 power source with
Current limit rated max. 2.5 Amps or less.
2. These products are only suitable for connection to a Class 2 or LPS power source, rated 24 Volt DC or less.
3. These products shall be mounted in equipment, which provide a suitable overall enclosure.
4. A maximum of 4 Led strips are allowed to be mounted in a row, as detailed in the mounting instructions.
5. These products may only be installed in a metal based enclosure (frame) that is able to transfer the heat that comes from the
LEDs over the metal-core Printing Wiring Board into the ambient.
MATRIX FRAME
FLEVOWEG 27
2318 BZ LEIDEN, THE NETHERLANDS
E358648
Class 2 LED driver box, Model A120606.
1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. The Class 2 output of the power supply is suitable for use in dry and damp locations only.
January 23, 2014
102
SIGN COMPONENTS MANUAL (SAM)
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. The load powered by the Class 2 output of the power supply rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
7. The suitability of strain relief, current leakage, and grounding tests shall be determined in the end-use product.
8. AC input and output connectors are not polarized. Suitability shall be determined in the end use.
MAXBRITE LED LIGHTING TECHNOLOGY LLC
1740-B JUNCTION AVE.
SAN JOSE, CA 95112
E313209
Class 2 LED Illumination Module, Cat. No. OTH-308X10x18-01 Series, x: indicate the COLOUR: R-Red, Y-Yellow, B-Blue, GGreen, W-White, YO-Yellow Orange.
1. These products are only suitable for connection to a UL Listed or Recognized maximum Class 2, 12 V DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit
limits.
3. Class 2 LED module, OTH-308X10x18-01 Series When units are connected to a Class 2 circuit, they are not to draw a total
wattage of greater than the secondary or output rating of the Class 2 supply. Each module is rated 0.2A.
4. These products are suitable for use in dry, damp or wet locations.
5. These products are not required to be enclosed or protected from the weather.
Class 2 LED Module, PL5050 Polar series, x: indicate the COLOUR; CW-Cool White; PW-Pure White; WW-Ware White; GLGolden Yellow; RGB-RGB; Y-Bright Yellow; R-Bright Red; B-Vivid Blue; G-Mega Green; A-Aquamarine. POLAR X Series;
Ribbon Strip Series; Super Tiny Series.1. These products are only suitable for connection to a UL Listed or Recognized
maximum Class 2, 12 V DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit
limits.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply. Each module is rated 60W, 5A, and Max. 120 of LED modules per string.
4. These products are suitable for use in dry, damp or wet locations.
5. These products are not required to be enclosed or protected from the weather.
Sign accessories, Class 2 LED power supplies, Model MB-12760-12V Multi Drive Series Maxbrite LED power supply.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Toggle Switch Boot, Model MB-TS20B.
1. This switch boot was evaluated for use on a MaxBrite toggle switch(WOYR2)/E355116 part number MB-TS20, with 19 mm long
actuator mounted on a 12 mm tall threaded stem, with a 12 x 1.0 mm thread. Suitability of any other switch size shall be
determined in the end product.
2. The suitability of the switch ratings shall be determined in the end product.
3. This product is acceptable for use in dry, damp and wet locations.
4. The water exclusion must be determined in the end product.
Class 2 LED Drivers, Models MDS27760-12, DS12745-12, MDS12760-12, SLS27720-12, SLS27730-12, MDS12060-12,
TPS12060-12, TPS27760-12.
1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
3. These products shall be enclosed in the end product.
4. These power supplies are suitable for use in dry and damp locations.
5. These devices are intended for factory installation only.
6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
Sign accessories, Class 2 LED power supplies, Models SLS27730-12V, SLS27730-24V, SLS27760-12V and SLS27760-24V.
1. The units have been evaluated using a resistive load resulting in an output rated current of (1) 2.5 A for SLS27730-12V, (2) 1.25
A for SLS27730-24V, (3) 5 A for SLS27760-12V, (4) 2.5 A for SLS27760-24V respectively. The need for repeating tests related
to heating and the isolated output shall be considered in the end product.
2. The units have been tested at 40ºC ambient. The measured maximum surface temperatures are as follows. Acceptable
operation at a higher temperature should be determined in end products.
Model Surface temperature (degree C) / Location
SLS27730-12V 50.9 / enclosure outside top of T1
SLS27730-24V 50.0 / enclosure outside top of T1
SLS27760-12V 59.9 / enclosure outside top of T1
SLS27760-24V 51.9 / enclosure outside top of T1
3. The units are intended for operated in a maximum 20 A branch circuit.
4. The LED driver bodies have been evaluated for certain wet location requirments. The thermoplastic UV rating determination and
precondition before impact not completed since it is anticipated the thermoplastic parts of this unit will be protected in the end
use. To be considered in end use.
5. Only the U-Shaped inside metal enclosure was considered as protective bonded for SLS27730-12V and SLS27730-24V, the
metal chassis of these models need to be reliably bonded to the earthed chassis in the end product. The outside metal
enclosure was considered as protective bonded for SLS27760-12V and SLS27760-24V.
103
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
6. The LED drivers are for built-in installation, the suitability of enclosure, mounting and input/output connections shall be
determined in end-use product.
7. The LED drivers are for factory-wiring only.
8. Certain UL 8750 wet location requirements have been completed on this component, acceptance is to be determined in the end
product on the need to account for any items not covered and to address any of the CSA requirements (CSA C22.2 No.250
etc).
9. The RTN output was connected to ground for all SELV Reliability and working voltage measurements as noted on the test data
page.
Class 2 LED Modules, Designated as PLMO-BBBBCC and ALT-SSKDD-ZZ Series, where M may be E or X; O may be 2 or 3; T
may be N, S or X; BBBB, SS, DD and ZZ may be any numeric characters; and CC may be any alphabetical characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 VDC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products may be secured in place in the end product by any means available.
MAXGREEN LED TECHNOLOGY AND ELECTRICAL SPECIALIST LLC
5349 E THE TOLEDO
LONG BEACH, CA 90803
E365649
Sign accessories, Class 2 LED power supplies, Models MG-2012, MG-2024, MG-3012, MG-3024, MG-6012, MG-6024, MG10012, MG-10024, MG-12012, MG-15012.
1. The output of this component complies with Class 2 requirements in the Standard for Class 2 Power Units, UL 1310.
2. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
3. These products shall be enclosed in the end product.
4. These power supplies are suitable for use in dry and damp locations.
5. These devices are intended for factory installation only.
6. This Class 2 power supply is not provided with any grounding. The enclosure must be grounded in the end product.
MEAN WELL ENTERPRISES CO LTD
28 WUQUAN 3RD RD WUGU DIST
NEW TAIPEI, 248 TAIWAN
E320521
LED array drivers, Model CLY-100-Z, Y can be G (for with Glue) or N (for without Glue), Z can be 12, 15, 20, 24, 27, 36 for output
voltage; Model PLN-100-Z, Z can be 12, 15, 20, 24, 27, 36 for output voltage; Models CLY-100-48, PLN-100-48, Y can be G (for
with Glue) or N (for without Glue).
1. These power supplies have a maximum of one Class 2 outputs. The output of these power supplies have been evaluated to
Class 2 output requirements for dc circuits.
2. These products have been evaluated for dry and damp locations use only..
3. These devices shall be mounted in the intended manner within a suitable electrical enclosure.
4. For Models CLN-100-Z only (Z=12, 15, 20, 24, 27, 36, or 48), the temperature measured on top enclosure surface of was 63C
during the Temperature Test. For Models PLN-100-Z only (Z=12, 15, 20, 24, 27, 36, or 48), the temperature measured on top
enclosure surface of was 72C during the Temperature Test. For Models CLG-100-Z only (Z=12, 15, 20, 24, 27, 36 or 48), the
temperature measured on top enclosure surface of was 66C during the Temperature Test. This data shall be used to determine
the suitability of insulating materials in close proximity to these devices.
5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
LED array drivers, Models LPV-20-5, LPV-20-12, LPV-20-15, LPV-20-24, LPC-20-350, LPC-20-700.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. These products are provided with the following electrical ratings:
Input
Model
Output
Vac
A
Hz
Vdc
LPV-20-5
100-240
0.55
50/60
5
A
3
LPV-20-12
100-240
0.55
50/60
12
1.67
LPV-20-15
100-240
0.55
50/60
15
1.33
LPV-20-24
100-240
0.55
50/60
24
0.84
LPC-20-350
100-240
0.55
50/60
48
0.35
LPC-20-700
100-240
0.55
50/60
30
0.70
5. These products shall be enclosed in the end product.
6. These power supplies are suitable for use in dry and damp locations.
LED array drivers, Model CLy-60-z, where y can be G (with potting compound) or N (without potting compound), z can be 12, 15,
20, 24, 27, 36 or 48 for output voltage. Models PLN-60-z, PLN-45-z, where z can be 12,15, 20, 24, 27, 36 or 48 for output voltage,
without potting compound.
January 23, 2014
104
SIGN COMPONENTS MANUAL (SAM)
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a max. of one Class 2 output.
2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
4. These products are provided with the following electrical ratings:
Input (ac)
Model
Output (dc)
V
A
Hz
V
A
CLy-60-12
(y=G or N), PLN-60-12
100-240
277
0.8
0.3
50/60
12
5.0
CLy-60-15
(y=G or N), PLN-60-15
100-240
277
0.8
0.3
50/60
15
4.0
CLy-60-20
(y=G or N), PLN-60-20
100-240
277
0.8
0.3
50/60
20
3.0
CLy-60-24
(y=G or N), PLN-60-24
100-240
277
0.8
0.3
50/60
24
2.5
CLy-60-27
(y=G or N), PLN-60-27
100-240
277
0.8
0.3
50/60
27
2.3
CLy-60-36
(y=G or N), PLN-60-36
100-240
277
0.8
0.3
50/60
36
1.7
CLy-60-48
(y=G or N), PLN-60-48
100-240
277
0.8
0.3
50/60
48
1.3
PLN-45-12
100-240
277
0.55
0.22
50/60
12
3.8
PLN-45-15
100-240
277
0.55
0.22
50/60
15
3.0
PLN-45-20
100-240
277
0.55
0.22
50/60
20
2.3
PLN-45-24
100-240
277
0.55
0.22
50/60
24
1.9
PLN-45-27
100-240
277
0.55
0.22
50/60
27
1.7
PLN-45-36
100-240
277
0.55
0.22
50/60
36
1.25
PLN-45-48
100-240
277
0.55
0.22
50/60
48
0.95
5. These products shall be enclosed in the end product.
6. These power supplies are suitable for use in dry and damp locations.
7. These products are suitable for factory wiring only.
LED array drivers, Model PLN-30-Y, where Y may be 9, 12, 15, 20, 24, 27 or 36 for output voltage.
1. These LED Drivers comply with the Class 2 output requirements.
2. The load connected to the Class 2 output of the LED Drivers other than Cat. Nos. PLN-30-36 and PLN-30-48 are suitable for
use in dry, damp and wet locations. The load connected to Cat. Nos. PLN-30-36 and PLN-30-48 are suitable for use in dry and
damp locations.
3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
4. These products are provided with the following electrical ratings:
Input
Model
Output
V ac
Hz
A
V dc
A
PLN-30-9
100-240, 277
50/60
0.45, 0.15
9
3.3
PLN -30-12
100-240, 277
50/60
0.45, 0.15
12
2.5
PLN-30-15
100-240, 277
50/60
0.45, 0.15
15
2.0
PLN-30-20
100-240, 277
50/60
0.45, 0.15
20
1.5
PLN-30-24
100-240, 277
50/60
0.45, 0.15
24
1.25
PLN-30-27
100-240, 277
50/60
0.45, 0.15
27
1.12
PLN-30-36
100-240, 277
50/60
0.45, 0.15
36
0.84
PLN-30-48
100-240, 277
50/60
0.45, 0.15
48
0.63
5. These products shall be enclosed in the end product.
6. These units are intended for factory installation only.
7. Model PLN-30-48 is suitable for use in the United States only.
LED array drivers, Model CEN-60-Y Series, where Y can be 12, 15, 20, 24, 30, 36, 42, 48 or 54 for output voltage; Model CEN75-Y, where Y can be 15, 20, 24, 30, 36, 42, 48 or 54 for output voltage.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
105
SIGN COMPONENTS MANUAL (SAM)
Input (ac)
Model
January 23, 2014
Output (dc)
V
A
Hz
V
A
CEN-60-12
100-240
277
0.8
0.3
50/60
12
5
CEN-60-15
100-240
277
0.8
0.3
50/60
15
4
CEN-60-20
100-240
277
0.8
0.3
50/60
20
3
CEN-60-24
100-240
277
0.8
0.3
50/60
24
2.5
CEN-60-30
100-240
277
0.8
0.3
50/60
30
2
CEN-60-36
100-240
277
0.8
0.3
50/60
36
1.7
CEN-60-42
100-240
277
0.8
0.3
50/60
42
1.45
CEN-60-48
100-240
277
0.8
0.3
50/60
48
1.3
CEN-60-54
100-240
277
0.8
0.3
50/60
54
1.15
CEN-75-15
100-240
277
1.1
0.4
50/60
15
5
CEN-75-20
100-240
277
1.1
0.4
50/60
20
3.75
CEN-75-24
100-240
277
1.1
0.4
50/60
24
3.15
CEN-75-30
100-240
277
1.1
0.4
50/60
30
2.5
CEN-75-36
100-240
277
1.1
0.4
50/60
36
2.1
CEN-75-42
100-240
277
1.1
0.4
50/60
42
1.8
CEN-75-48
100-240
277
1.1
0.4
50/60
48
1.57
CEN-75-54
100-240
277
1.1
0.4
50/60
54
1.4
3. The Class 2 output of these power supplies are suitable for use in dry and damp locations.
4. In the end product, power supply spacing to other heat producing components and to sidewalls shall be minimum 4 inch, 1 inch
end to end and minimum 2 inches spacing to top of enclosure.
5. These products shall be enclosed in the end product.
6. These products are suitable for factory wiring only.
7. In Canada Models CEN-60-48, CEN-60-54, CEN-75-48 and CEN-75-54 must have their Class 2 output circuit and components
completely inaccessible in the end product application.
LED array drivers, Models LPV-60-12, LPV-60-15, LPV-60-24, LPV-60-36 and LPV-60-48.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Input
Model
Output
Vac
A
Hz
Vdc
A
LPV-60-12
100-240
1.2
50/60
12
5.0
LPV-60-15
100-240
1.2
50/60
15
4.0
LPV-60-24
100-240
1.2
50/60
24
2.5
LPV-60-36
100-240
1.2
50/60
36
1.67
LPV-60-48
100-240
1.2
50/60
48
1.25
3. The Class 2 output of these power supplies are suitable for use in dry and damp locations only.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. These products shall be enclosed in the end product.
6. These products are suitable for factory wiring only.
7. Model LPV-60-48 is only acceptable for use with the product in the US.
8. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
MEGAPULL INC
161 TROLLINGWOOD LANE
E318039
January 23, 2014
106
SIGN COMPONENTS MANUAL (SAM)
MORRISVILLE, NC 28117
Class 2 LED Module, Cat. No. AABBCCEEFFG MMDDYY series, where AA may be FL, DL or RE, where BB may be CX, LK, LR,
LC, NI, AV, OS, AO, AB, CR, LU, SE, or OT, where CC may be BL, RE, GR WH, CW, NW, WW, CY, RB, RO, AM or OT, where
EE may be WB, or NB, where FF may be SP or DP, where G may be any number from 0 to 9, where MMDDYY may be may be
any number combinations from 000000 to 999999.
1. For connection to the Class 2 output of a Listed or Recognized Component power source rated 15 Vac or 36Vdc maximum.
Other applications require additional evaluation.
2. Class 2 LED Modules, Cat. No. No. AA01BBCCEEFFG MMDDYY series are each rated max. 5 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
3. These products are suitable for use in dry, damp and wet locations when rated 15 Vac or 30Vdc maximum. Products that are
rated maximum of 36 VDC are suitable for dry and damp locations only.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
MIC ELECTRONICS LTD
A-4, ELECTRONIC COMPLEX
KUSHAIGUDA,
HYDERABAD, AP 500062 INDIA
E351950
Dry location, Indoor LED Display Module signs, Models DigiTile-9RC, DigiTile-12RC.
1. Acceptability for multiple connections (daisy chaining) not exceeding 12 A (based on 14AWG power supply cord) on a single
branch circuit shall be determined by the end product requirements.
2. These products were tested for use at a room ambient temperature of 25°C. Testing was conducted on the test bench
positioned vertically facing horizontally. The need for conducting temperature testing in the end product shall be considered
where the units are installed in a higher ambient.
3. The suitability of the mounting means shall be determined in the end use.
4. The Leakage current test shall be conducted in the end use for cord connected signs.
5. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
6. The sign components are for dry location use.
7. The suitability of Power Supply Cord needs to be determined in the end use.
8. This product was not tested for conformal coating ageing test. The coating shall be applied on R/C PWB for indoor application
only. The need for conducting the test shall be determined in the end use based on spacing and pollution degree as per end
product requirements.
9. This product was tested for 5VA flame test on the front sign side.
MICRALUX INC
1162 N REESE DR
PROVO, UT 84601
E235719
Class 2 LED Module, Cat. Nos. LED Strips
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from weather.
LED Power Converter, Class 2, Cat. Nos. PS24.
1. These products are suitable for use in dry and damp location. In wet location Signs, these products are to be installed where
protected from rain, snow and water spray by water shield or sign body.
2. These products are intended for use only connected to a Class 2 circuit power.
3. Each output of this product complies with Class 2 requirements.
MITSUBISHI PLASTICS COMPOSITES AMERICA INC
401 VOLVO PKY
CHESAPEAKE, VA 23320
E318242
Structural Panels, Models AP44(#2)(#4), AP33(#1)(#3), LT23(#1)(#5), LT24(#2)(#5), LT33(#1)(#6), LT34(#2)(#6), LT43(#1)(#7),
LT44(#2)(#7).
1. Instructions shall be provided that illustrate the proper cutting, pointing, installation and securement to a building surface of a
structural panel.
2. Acceptable for use in dry, damp and wet locations.
3. Structural panels are suitable for supporting enclosures, plastic faces, and moldings that are reliably secured to the panel.
4. Structural panels are not suitable for use as the enclosure of bare live parts or wiring.
5. Components other that neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers of
minimum 7/16 (11mm) diameter.
6. All exposed edges of a structural panel, including drilled holes, etc. shall be treated with two coats of outdoor paint or wood
coating.
7. These structural panels did not comply with the component Support test. Therefore, sheet metal screws shall not be used to
fasten components to these panels.
107
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
8. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 (254mm)
from a point of support.
9. The metal faces shall be grounded in accordance with the Standard for Electric Signs (UL 48). Separate grounding straps shall
be used when necessary.
10. Water exclusion of the end-product shall be determined in the end product.
11. Minimum 5 cm (2 in) spacing from heat producing components required.
12. Suitable for the connection and support of conduit.
13. All metal surfaces exposed to contact during normal use or routine maintenance shall be bonded and/or grounded in
accordance with UL 48.
MULTIPANEL UK LTD
UNIT 6 SITE 2
OAK BUSINESS UNITS THORVERTON ROAD
MATFORD
EXETER, DEVON EX2 8FS UNITED KINGDOM
E322586
Structural panel, Cat. Nos. designated "ALUPANEL".
1. Illustrate the proper cutting, pointing, installation, component securement and securement to a building surface of a structural
panel.
2. Structural panels have been evaluated for wet location with 50C ambient.
3. Structural panels may be employed as external decorative faces and are acceptable for support of complete electrical
enclosures, plastic faces, and moldings that are reliably secured to the panel.
4. Structural panels are not suitable to be used as the enclosure of bare live parts or wiring.
5. Nuts and bolts must be used when fastening a ballast or transformer weighing more than 7-1/2 lbs (3.4 kg); and
6. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
N GLANTZ & SON
2501 CONSTANT COMMENT PL
LOUISVILLE, KY 40299
E352418
Structural panels, Models EMPBXXXX Series, where XXXX can be any alpha numeric characters or blank.
1. The structural panel is suitable for use in dry, damp and wet locations.
2. The structural panel may be used in decorative and sign body applications, and shall not be used as part of the sign enclosure.
3. The panel is not suitable for use in component mounting and support applications.
4. Rain tightness shall be determined in the end product.
5. Electrical spacing and bonding for grounding shall comply with the end product standard.
6. Not suitable for use in terminating conduit.
7. Any parts other than neon standoffs or small decorative parts secured to the panel must be secured by means of through bolts,
nuts and washers. The minimum washer diameter is 7/16 in.
8. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
9. The structural panels are rated 75°C, where consideration will need to be given to end product thermal spacing from heat
producing components.
10. These materials are available as unpainted aluminum or pre-painted aluminum.
11. This material has not been investigated for the securement of conduit, electrode housings or the like, suitability shall be
determined in the end product.
NANJING CEDAR GREEN TECHNOLOGIES CO LTD
739 SHENGAN AVENUEY
BINJIANG DEVELOPMENT AREA
JIANGNING DISTRICT
NANJING, JIANGSU CHINA
E358556
Class 2 LED modules, Cat. No. CD-MXX-XXX-XX-XX-XXX series. The first X can be any one of the Arabic numerals of 1 through
9, these indicate LED quantity; The second X can be any letter in alphabet, represent for beam angel; The third X is for the supplier
of the lamp; The fourth X is for the model of the lamp; The fifth X can be any one of alphanumeric characters; The sixth and
seventh X is for the color; The eighth and ninth X is for the product versions; The last three X are for the input voltage, 12V
represent the input voltage is 12VDC, 15V represent the input voltage is 15VDC.
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. (For model CD- MXX-XXXXX-XX-15V)
2. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less. (For model CD- MXX-XXXXX-XX-12V)
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
4. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
5. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Vdc or less. (For model CDMXX-XXX-XX-XX-15V)
6. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less. (For model CDMXX-XXX-XX-XX-12V)
7. These products are not required to be enclosed or protected from the weather in the end product.
8. The suitability of supply leads shall be determined in end use.
January 23, 2014
108
SIGN COMPONENTS MANUAL (SAM)
NANOLUMENS INC
4900 AVALON RIDGE PKY
NORCROSS, GA 30071
E348993
Component Signs, Models NS-400, NS-500, NS-521, NS-600, NS-625, NS-1000.
1. These components should be installed in accordance with the manufacturer’s installation instructions.
2. These products are suitable for use in dry locations.
3. Each power supply can only drive max number of 15 modules.
4. These units are rated as follows;
Input
Model Designation
NS-400, NS-500, NS-521,
NS-600, NS-625, NS1000
Output Per Power Supply
Input Voltage
(Vac)
Max. Input Current
(A)
Input Frequency
(Hz)
Output Voltage
(Vdc)
Max. Output Current
(A)
120-240
5-2.5
50/60
5
60
5. These products shall be enclosed in a suitable electric enclosure in the end product.
6. When provided with attachment plug, this product shall be connected to a dedicated receptacle in a permanently connected
sign.
7. These products are suitable for factory installation only.
NC LED CO LTD
16-17 GAGOK-RI
HWADO-EUP
NAMYANGJU-SI, GYEONGGI-DO 472-841 REPUBLIC OF KOREA
E347462
Sign Accessories, Class 2 LED Modules: HLC1, HLC2S, HLC2, HLC3S, HLC3, HLC4, OMX-L4, OMX-L3, OMX-M3, OMX-M2,
OMX-S2, OMX-N1, CC-IP-04, CC-IP-03L, CC-IP-03, CC-IP-02L, CC-IP-02, CC-IP-01, ELW4, ELW3L, ELW3, ELW2L, ELW2,
ELW1, CCL4S, CCL3L, CCL3, CCL2L, CCL2, CCL1, LX-HLC4, LX-HLC3S, LX-HLC2S, ECO1, ECO2S, ECO2, ECO3S, ECO3,
ECO4, EC-IP-04, EC-IP-03L, EC-IP-03, EC-IP-02L, EC-IP-02, EC-IP-01, eco max OMX-L4, eco max OMX-L3, eco max OMX-M3,
eco max OMX-M2, eco max OMX-S2, eco max OMX-N1, LX-ECO4, LX-ECO3S, LX-ECO2S, NCP1, NCP2S, NCP2, NCP3S,
NCP3, NCP4, CCL4, NCC3, NCC3S, NCC2, NCC2S, NCC1, LX-HLC4, LX-HLC3S, LX-HLC2S, LX-ECO4, LX-ECO3S, LXECO2S, MINI3, RGB3, RGB4, LX-RGB3, LX-RGB4.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means.
NCTECH CO LTD
22 BIRYONG-RO 524BEON-GIL
HWADO-EUP
NAMYANGJU-SI, GYEONGGI-DO 472-841 REPUBLIC OF KOREA
E364127
Component sign accessories, Class 2 LED power supply, Model NCP60AL-PF-12VC.
1. This Power Supply complies with the Class 2 output requirements and has one Class 2 outputs.
2. This unit is suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
4. These products are provided with the following electrical ratings:
Model No.
Input
Voltage
(Vac)
Input Frequency
(Hz)
Power
Consumption(W)
NCP60ALPF-12VC
100-277
50/60
76
Input Output Voltage
Current
(Vdc)
(A)
0.83
12
Output
Current
(A)
Output
Wattage
(W)
5.0
60
5. This product shall be enclosed in the end product.
6. In the end product, power supply shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
7. The unit is intended for being used in fixed signs.
8. The input and output connections have been investigated for factory wiring only. The need for other consideration should be
considered in end-use product.
9. This product is intended to be used in the condition Variable Resister (VR1) set to 343 Ohm.
10. The LED driver has been temperature tested in a 50 °C ambient, where the maximum temperatures on the outer surface of the
enclosure above Transformer (T2) reached 77.8 °C. The need for further evaluation of the internal components shall be
considered if enclosure temperatures exceed this value when subjected to temperature testing in the end product.
NEO-NEON LED LIGHTING INTERNATIONAL LTD
E252578
109
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
BLK B, 12th FL
ELDEX INDUSTRIAL BLDG
21 MA TAU WAI RD
HUNG HOM, KOWLOON HONG KONG
LED String System, Cat. Nos. LED vertical PCB, Model LC-BL-300-12V-**. LED vertical PCB, Model LC-BL-300-12V-**. LED
horizontal PCB, Model LC-BL-110S-12V-**. LED horizontal PCB, Model LC-BL-110S-12V-**. LED horizontal PCB string, Model
LC-BL-24V-6-TYPE A-**. LED horizontal PCB string, Model LC-BL-24V-6-TYPE A-**. LED horizontal PCB string, Model LC-BL24V-6-TYPE B-**. LED horizontal PCB edge lite, Model LBLU-10x88-6-12V-**. LED horizontal PCB edge lite, Model LBLU-10x886-12V-**. LED vertical flex PCB, Model LBLU(FX)-V-6.25\'-12V-**. LED flexible listel light, Model FLF-99-1M-12V-**. LED tubes,
Models LN-MN-300-24V-M(W), LN-MN-600-24V-M(W), LN-MN-1000-24V-M(W), and LED tube controller, Model SRC-181-24V.
LED back light string, Model LBLS-PL-2P-12V-**, LBLS-AL-2P-12V-**, and LF(V)-A-1-12V-**. LED high power back light, Model
LBLS-AL-CC350-**, and LBLS-PL-CC350-**. LED linear flex, Model LBLU(FX)-H-10x420-10-24V-**.
** can be replaced by additional letters or numbers to indicate color.
1.
LED's may be supplied by a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2, 24 VDC maximum
output power source.
2.
LED's were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2 source.
3.
These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limiting requirements.
4.
These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
5.
Certain products described in this section may be cut into segments through a cutting line provided on the printed wiring
board. No other cut across the board is permitted.
6.
Units may be provided with UYMR2, 3M type 4950 double sided adhesive tape.
LED Outline Lighting, Rectifier for 6VDC and 12V DC Class 2 Circuit, Model No. MLF(H)-2W-5X8*a*b*c, may have suffixes a,
b or c (a = 3Ft - 132Ft.; b = 6Vdc or 12Vdc; c = R, Y, W, G, B (LED lamp color)).
Note: 3Ft - 120Ft for 6V DC, 3Ft - 132Ft for 12VDC
1.
These products are only suitable for connection to a UL Recognized (UYMR2) Class 2 Power supply with a continuous
output of 6 Vdc or 12 Vdc.
2. These products may be connected to a 6V or 12 V AC, UL Recognized (UYMR2) Class 2 power source when provided with
optional rectifier.
3. These products are rated to draw 4.5 Amps at 12Vdc at a 132Ft maximum and 4 Amps at 6 Vdc at 120Ft maximum. Each
unit shall be connected so as to not exceed the output current and power rating of the power supply.
4. These products, when connected to a UL Recognized (UYMR2), Class 2 Power supply with a continuous output of 6 Vdc or
12 Vdc, are suitable for installation in wet, damp and dry locations.
5. These products described in this section may be cut into segments only through a cutting mark symbol provided on the LED
strip.
6. Units may be provided with UYMR2, 3M type 4950 double-sided adhesive tape. Tape must be utilized per UYMR2
“Conditions of Use” as defined in the Sign Components Manual.
7. Mounting Clips may be used on walls, pillars doorframes or the like places.
LED Modules, Component Sign Accessories, Class 2 Powered LED Module, Cat. No. LP-PIXDOT-Ø30-5V or LS-DIA34-5VM, where each Cat. No. may be optionally followed by a letter from A to Z or by a number from 0 to 9.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 Powered LED Module, cat. no. LP-PIXDOT-Ø30-5V or LS-DIA34-5V-M is each rated max. 3.6 Watts per unit. When
units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of
the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
NEON TECH
1965 PLAZA REAL
OCEANSIDE, CA 92056
E307713
Class 2 LED Power Supply, Model LT380.
1. This power supply has a Class 2 output that has been evaluated to Class 2 output requirements for dc circuits.
2. This product with Class 2 outputs are suitable for use only in dry locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
NEXUSLED GREEN TECHNOLOGY SDN BHD
6 JLN SRI SULONG SELATAN
TMN INDUSTRI SRI SULONG
83000 BATU PAHAT, JOHOR MALAYSIA
E331480
Class 2 LED Module, designated P58A2, SD1, SN2E.
1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory Class 2
power supply.
2. These components have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
January 23, 2014
110
SIGN COMPONENTS MANUAL (SAM)
3. Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical
enclosure.
4. Models SN2E and P5-8A2 are suitable for use in dry, damp and wet locations. Model SD1 is suitable for use in dry and damp
locations.
NIVEN MARKETING GROUP
955 KIMBERLY DR
CAROL STREAM, IL 60188-1806
E344900
Light Kit Assembly, designated as "Surf Board Display Kit" System.
1. These products shall be installed in accordance with the manufacturer’s instructions.
2. These products are suitable for use in dry locations only.
3. These products are for factory wiring only in sign or outline lighting related application.
4. Wiring and means of connection between modules shall be investigated in the end product requirements.
5. The unit is not provided with mounting means. The mounting means requirements shall be considered in the end product.
6. The suitability of installation shall be determined in the end product applications.
NORA LIGHTING
6505 GAYHART ST
CITY OF COMMERCE, CA 90040
E352531
Class 2 Power Supply, Models NMT-244/12C2D1, NMT-303/24C2D1.
1. These power supplies have been evaluated for use in portable LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected to
another power source.
5. The attachment plug on the end of the power supply cord is not to be removed.
Class 2 LED modules, Models NUFLED-110/30, NUFLED-110/65.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
Class 2 LED modules, Models NUFLED-115/30, NUFLED-115/65.
1. These products are only suitable for connection to the output of a Class 2 power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. The LED modules are rated as noted in the electrical ratings table. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end products by any means available.
Class 2 LED modules, Models NUTP4 SERIES, NUTP1 SERIES, NUTP7 SERIES, NUTP6 SERIES, NUTP3 SERIES, NUTP5
SERIES, NUTP8 SERIES, NUTP2 SERIES.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Modules, Models LS0723x, LS0766x, LS0769x, LS0776x, LS0782x, LS0783x, and LS-KM02-x where that x may be R, G, B,
Y, CW, WW, P or O indicating LED Color.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
NORLOK TECHNOLOGY INC
26 ADAMS BLVD
BRANTFORD, ON N3S 7V2 CANADA
E242292
Metal Joiner System, LETTER LOK Series of clinchlok machines such as LETTER LOK 2000 in combination with one of the
following dies inserts Part No. MP70001 or Part No. MP70002 with punch Part No. MP70010 is for use in joining painted or
unpainted sheet aluminum.
111
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
1. Die insert Chief Enterprises Part No. MP70001 is suitable for joining painted or unpainted aluminum nominal 0.040 in. thick
(0.034 in. thick minimum) into painted or unpainted aluminum nominal 0.040 in. thick (0.034 in. thick minimum). Minor diameter
of button not including the tabs made by the material flowing past the die blades 0.285 in. maximum.
2. Die insert Chief Enterprises Part No. MP70001 is suitable for joining painted or unpainted aluminum nominal 0.040 in. thick
(0.034 in. thick minimum) into painted or unpainted aluminum nominal 0.063 in. thick (0.056 in. thick minimum). Minor
diameter of button not including the tabs made by the material flowing past the die blades 0.295 in. maximum.
3 Die insert Chief Enterprises Part No. MP70002 is suitable for joining painted or unpainted aluminum nominal 0.063 in. thick
(0.056 in. thick minimum) into painted or unpainted aluminum nominal 0.090 in. thick (0.080 in. thick minimum) or painted or
unpainted aluminum nominal 0.063 in. thick (0.056 in. thick minimum) to painted or unpainted aluminum nominal 0.063 in. thick
(0.056 in. thick minimum). Minor diameter of button not including the tabs made by the material flowing past the die blades
0.285 in. maximum.
4. Punch Chief Enterprises Part No. MP70010 for use with any of the above die inserts
5. Minimum spacing between clinches is 0.5 in. Maximum spacing between clinches is 4 in.
6. The tooling has been evaluated for joining only two pieces of aluminum, painted or unpainted.
7. Best results are when joining two pieces of aluminum having the same nominal thickness. Aluminum in the same thickness
ranges described above may be joined provided the thicker piece forms the mushroom cap.
8. Total combined thickness of aluminum shall not exceed 0.15 in.
9. The thicker material shall not be more than twice the thickness of the thinner material.
10. The depth of the die cup has a nominal thickness equal to both layers of aluminum.
11. Clinches shall be inspected before the next production step to verify that the minor diameter is greater than 0.24 in. and less
than the values specified above.
12. Clinches shall be inspected before the next production step to verify that they are round, free of cracks on mushroom cap, and
free of cracks inside joint cup. Double struck clinches are not acceptable.
13. The die, punches and LetterLok machines shall be serviced and maintained in accordance with the manufacturers instructions.
14. A service log by date shall be kept for each machine. Each punch and die change shall be noted. Each change in set up for
material thickness shall be noted. Punch and die usage shall be monitored and the tools replaced at least in accordance with
the manufacturers replacement instructions.
15. Assemblies with defective clinches shall be reworked by adding a like number of defect free clinches adjacent to each bad
clinch. Instead of reworking, the assembly shall be scrapped.
NUDO PRODUCTS INC
1500 TAYLOR AVE
SPRINGFIELD, IL 62703
E180252
Structural panels, consisting of a plywood core faced on both sides with sheet aluminum, Type Nu-Alum.
1. The panels may be used as part of a sign body but shall not be relied upon as an electrical enclosure.
2. Any parts other than neon standoffs or small decorative parts secured to the panel must be secured by means of through
screws or bolts, nuts and washers.
3. The backing is not to be considered as providing a weatherproof enclosure, therefore, all internal sign components shall be
suitable for outdoor use.
4. All heat producing components such as ballasts, fluorescent lamps and starters, transformers, electrodes and the like shall be
spaced at least 1 inch from the structural backing.
Structural panels, consisting of a polypropylene core faced on both sides with sheet aluminum, Type Aluma Core.
1. The structural panel may be employed as external decorative faces and for the support of complete electrical enclosures.
2. The structural panel is not to be used to enclose bare live parts or wiring.
3. Enclosures, plastic faces, and moldings may rely upon the structural panel for support. These components are to be reliably
secured to the panel.
4. Any parts other than neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers. The
minimum washer diameter is 7/16 inch.
Structural panels, Models PolyMetal and Elements.
1. Suitable for use in dry, damp and wet locations.
2. Suitable for use in decorative and sign body applications only.
3. Suitable for use in component support applications. When threaded directly into the panels, suitability of screws shall be
determined in the end product.
4. Rain tightness shall be determined in the end product.
5. Electrical spacings and bonding for grounding shall comply with the end product standard.
6. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
7. These materials are rated Polyethylene. Consideration will need to be given to end product thermal spacings from heat
producing components or temperature test.
8. These materials are available as unpainted aluminum or pre-painted aluminum.
9. This material has not been investigated for the securement of conduit, electrode housings or the like, suitability shall be
determined in the end product.
OK INDUSTRY INC
102-905 BUCHEON TECHNOPARK
364 SAMJUNG-DONG OJEONG-GU
BUCHEON, GYEONGGI-DO 421-740 REPUBLIC OF KOREA
E340391
Class 2 LED Modules, Models B301W20*, W30*, W40*, W50*, RGB20*, RGB30*, RGB40*, R20*/B20*/G20*, R30*/B30*/G30*.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
January 23, 2014
112
SIGN COMPONENTS MANUAL (SAM)
3. These products are each rated max. 1.44 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp, and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
OPTEK TECHNOLOGY INC
SUITE 130
M S 411
1645 WALLACE DR
CARROLLTON, TX 75006
E339817
Class 2 LED Strips, Cat. Nos. OVM12F3x7 Series, OVM18F4x7 Series, OPA775, OPA776 and OVQ12S30x7 Series.
1. These products are only suitable for connection to a Class 2 power source, rated 12 - 24 Volts DC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at rated 12 - 21.2 Volts DC. Model
OPA776 is suitable for use in dry and damp locations only.
5. These products are not required to be enclosed or protected from the weather in the end product.
ORDER-MATIC ELECTRONICS CORP
320 S BRYANT PL
DEL CITY, OK 73115
E328326
Class 2 LED Panel, Cat. No. Model MDMON.
1. These products are required to be enclosed in the end use sign.
2. These products are intended only for factory installation in new signs.
3. Grounding of frame to supply ground is required. Suitability of bonding for grounding connection is to be determined in final
application.
4. Suitability of LCD panel mounting shall be determined in final application.
5. In the end product, the LCD panel spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
6. These products are only suitable for connection to a circuit from a Class 2 power source.
OSRAM SYLVANIA INC
54 CHERRY HILL DR
DANVERS, MA 01923
E220096
LED Array Drivers, Models OT3W/350C/120-240V, OT240/120-240/24/CH3, OT96/120-277/24, OT96/120-277/24X, OT240/120240/24/CH, OT240/120-240/12/CH, OT25W/700C/UNV, OT20W/10V/120-240V, OT17W/700C/UNV, OT17W/24V/UNV,
OT40W/1400C/UNV, OT40/120-277/1050E, OT40/120-277/850E, OT25W/1040C/UNV, OT40W/1110C/UNV.
1. These power supplies have multiple outputs. Power supply Model OT240/120-240/12/CH has a maximum of four Class 2
outputs. Power supply Models 0T3/120-240/350 and OT240/120-240/24/CH have maximum three Class 2 outputs. Each output
of these power supplies have been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 2 inches.
4. When not marked for dry and damp locations only, all units shall be provided with liquid tight fittings on the primary and
secondary circuits.
5. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
LED Array Drivers, Models OT25/120/10, OT50/120/10, OT75/120/24.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class
2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These lead connected products are suitable for use in commercial application only when marked with 277 V input voltage.
OSRAM SYLVANIA INC
54 CHERRY HILL DR
DANVERS, MA 01923
E258264
Class 2 LED Illumination Module, Cat. Nos. OS-LM01A-X, OS-LM03A-X, where X may be replaced with any letters of the
alphabet A to Z, or any number from 0 to 9, or any combination of letter and numbers representing different LED colors ;
LINEAR/LM01A/W3F/XXX and L4LRE/10V/XXX/LNRLT, where X can be any number from 0-9 indicating color temperature.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory.
113
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Class 2 LED Illumination Module: Cat Nos. OS-LM01A-X, OS/LM01A/X, OS-LM03A-X, and OS/LM03A/X are each rated max.
7.5 Watts per unit. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater
than the maximum secondary or output current rating of each Class 2 circuit.
4. These products are suitable for use in dry, damp, or wet locations.
5. These products are not required to be enclosed or protected from weather.
Class 2 LED Illumination Module, Cat Nos. OS-LM10A-X OS-LM10A-X, where X may be replaced with any letters of the
alphabet A to Z, or any number from 0 to 9, or any combination of letter and numbers representing different LED colors.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Each Class 2 LED Illumination module is rated for a maximum 86.4 W. When units are connected to a Class 2 circuit, their total
length is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2
circuit.
4. These products are suitable for use in dry, damp, or wet locations.
Class 2 LED Illumination Module, Cat No. "HF2Chain/36/W3/865-12ft".
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Lighting Assemblies, Model "HF2Chain/36/W3/865-12ft" is each rated max. 53 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 Lighting Assemblies, Cat. No. “LINEARlight POWER FLEX”, Model LM10P/W3-xxx where xxx may be replaced with any
letters of alphabet A through Z and any numbers 0 through 9 or combination of letter and numbers.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 Lighting Assemblies, “LINEARlight POWER FLEX”, model no. LM10P/W3-xxx is each rated max. 75 Watts per unit.
When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LEDs, Cat. No. HF2-STICK-XB.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. Suitability for use with a
power supply that does not comply with Class 2 requirements has not been determined.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products are not required to be enclosed or protected from the weather in the end product.
Lighting Illumination, Model "HF2Chain/xx/xxxxx". Where xx refers to the number of LED's and xxxxx refers to the color and
temperature of LED's; x can be any letter or number.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. Class 2 LED Lighting Assemblies, Model "HF2Chain/36/W3-835-12ft" is each rated max. 52 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Lighting Assemblies, Model HF2CHAIN HIGH EFFICIENCY/HF2CHAIN DC02B.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. These modules are each rated max. 72 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Illumination Module, Cat Nos. BL02LT-A1, BL02ST-A1, BL02STB1, BL02ST-O1, BL02ST-S1, BL02ST-T2,
BL02ST-W2-865 and BL02ST-Y2.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
114
3. Class 2 LEDs Cat. Nos. BL02LT-A1, BL02ST-A1, BL02STB1, BL02ST-O1, BL02ST-S1, BL02ST-T2, BL02ST-W2-865 and
BL02ST-Y2X are each rated max. 23 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total
wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LEDs, Cat. No. OS/DS6/W2-847 and OS/DS12/W2-847.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LEDs Cat. Nos. OS/DS6/W2-847 and OS/DS12/W2-847 are each rated max. 17 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Modules, Cat. No. OS/DC36/W2-865.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Module Cat. Nos. OS/DC36/W2-865 is each rated max. 60 Watts per unit. When units are connected to a Class
2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LEDs, Cat. No. OS-DT6-W2-XXX, where XXX is any alphanumeric combination.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Modules Cat. Nos. OS/DS6/W2-847 and OS/DS12/W2-847 are each rated max. 17 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LEDs, Cat. No. OS-LM10L-XXX, where XXX is any alphanumeric combination denoting color.
1. These products are only suitable for connection to a Class 2 24 VDC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited circuit.
3. Class 2 LED Module Cat. Nos. OS-LM10L-XXX are each rated max. 24 VDC, 2.25 A, 54 Watts per string. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max 30 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LEDs, Cat. No. BACKlight2G/YYY/BL04ST/XXX, where YYY may be either any alphanumeric combination or optional and
XXX is any alphanumeric combination denoting color or characteristic of the LED.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Module Cat. Nos. BACKlight2G/YYY/BL04ST/XXX is each rated max. 38 Watts per unit. When units are connected
to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LEDs, Models HF2X, DX1 and L1DE/350C/xxx/yyy/x Series.
1. These Class 2 LED Modules are only suitable for connection to a Class 2 constant current power source only.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. These Class 2 LED modules are rated max. 2 Watts per LED module. When these units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in wet locations.
5. These products are not required to be enclosed in the end product.
LED Lighting Assemblies, Cat. No. PROMINENCE Contour Lighting Assemblies", "PROMINENCE ™ Stall Star",
"PROMINENCE ™ Blue 2\' Radius Tube.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 Lighting Assemblies, Model “PROMINENCE Contour Lighting Assemblies”, “PROMINENCE ™ Stall Star“ and
“PROMINENCE ™ Blue 2' Radius Tube“ series is each rated max. 75 Watts per unit. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Power Supplies, Model 0T3/120-240/350.
1. These power supplies have multiple outputs. Power supply has a maximum of four Class 2 outputs. Each output of these power
supplies have been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
115
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 2 inches.
4. When not marked for dry and damp locations only, all units shall be provided with liquid tight fittings on the primary and
secondary circuits.
5. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
LED Array Drivers Models OT10/120-240/350 E, OT10/120-240/12 E, OT25/120-240/12 E, OT60/120-277/12 E.
1. The electrical ratings are as follows:
Model
Input, 50/60 HZ, V
Input, A
Output, Vac
Output, A ac
VA or Pmax
OT10/120-240/12 E
120-240
0.175-0.120
12
0.833
10 VA
OT10/120-240/350 E
120-240
0.175-0.120
2.3-28
0.350
10 VA
OT60/120-277/12 E
85-277
0.11-0.3
8
3.0
25 Pmax
OT25/120-240/12 E
85-277
0.11-0.3
12
2.0
25 Pmax
2. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
3. A suitable Fire and Electrical Enclosure shall be provided in the end product.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. These power supplies are only suitable for use in dry and damp locations.
6. Models LVD 25 8, LVD 25 12 and LVD 25 24 were tested inside an enclosed box with 2 inch spacing on each side.
LED Power Supplies, Cat. No. OT60/120-277/12 E
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. The electrical ratings are as follows:
Input, 60 Hz
Output, DC
Model
V
A
V
VA
OT60/120-277/12E
100 - 277
0.8 - 0.3
12
60
3. These power supplies are only suitable for use in dry and damp locations.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
LED Power Supplies, Cat. No. Optotronic OT20/120-240/24S.
1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 50C.
3. The drivers are intended for installation inside an electrical enclosure.
4. The drivers may be mounted inside an electrical enclosure with 1 inch spacing end to end and 4 inch spacing side to side.
5. The ground connection is suitable as the equipment ground for a sign connected to a maximum 15A branch circuit. Separate
provision for sign grounding must be provided when connected to a 20 A branch circuit.
6. The drivers are suitable for dry or damp location use.
LED Array Drivers, Cat. No. OT 6/100-120/10 CE, and OT 6/100-120/24 CE.
1. The suitability of the mounting means shall be determined in the end-use product.
2. OT 6/100-120/10 CE and OT 6/100-120/24 CE employ a R/C (OBJY2) Class B(130)ins. system and have been evaluated at
an elevated ambient of 50 C. Temperature testing is required in the end product and the ambient cannot exceed 50C.
3. Leakage testing shall be performed in the end product if installed in a cord connected sign.
4. A suitable Enclosure with a conduit connection means shall be provided in the end-product.
5. These components are intended for dry and damp locations only.
LED Power Supplies, Cat. No. OT 75/120-277/24E and OT 50/120-277/10E.
1. The suitability of the mounting means shall be determined in the end-use product.
2. Input supply means is provided by minimum 6” length of leads intended for field wiring. Acceptability of this construction is
to be determined as part of the end product evaluation.
3. The acceptability of the output leads shall be determined in the end product.
4. Model OT 50/120-277/10E has been evaluated at an ambient of 60° C.
5. Model OT 75/120-277/24E has been evaluated at an ambient of 50° C.
6. Model OT 75/120-277/24E has been additionally evaluated at an ambient of 60°C, when R/C (OBJY2) Class F, type KIS-ME02
by Kaschke is utilized.
7 Grounding lead shall be crimped between top and bottom of enclosure case. This ground is for functional grounding purposes
only and shall not be relied upon for safety grounding.
LED Power Supplies, Cat. No. OT 9/100-120/350E and OT 8/100-120-24E.
1. The suitability of the mounting means shall be determined in the end-use product.
2. Model OT 9/100-120/350E has been evaluated at an ambient of 50 C.
3. The input/output connectors have not been evaluated for field connections and are only intended for connection to mating
connectors of internal wiring inside the end-use product.
4. Leakage test shall be performed in the end product.
5. A suitable Fire and Electrical Enclosure shall be provided in the end-product.
LED Dimmer Controller, Model No. OPTOTRONIC OT DMX RGB DIM.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated max 24VDC.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
116
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
4. These products are rated per the Table below. When units are connected to a Class 2 circuit, their ratings are to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
LED Dimmer Controller, Model OPTOTRONIC OT DIM.
1. These devices shall be mounted in equipment, which provide a suitable overall enclosure.
2. These products are only suitable for connection to a Class 2 or LPS power source, rated 24 Volt DC or less.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy requirements.
4. These products are suitable for use in dry and damp locations.
5. These products comply with Class 2 limits when the dimmer circuit is not connected. If the dimmer circuit is connected, a
suitable enclosure or accessibility barrier is to be provided for the output wiring and components.
Class 2, 12, 15, 24 VDC, LED rope assemblies, Models LMultiFLX/Thn/W3-865-3.2ft, LLMultiFLX/Thn/W3-827-3.2ft,
LLMultiFLX/Thn/W3-888-3.2ft.
1. For a portable indoor sign, these products are suitable for connection to a 12, 15, 24 VDC, 0.5A, UL Listed Class 2 power
supply.
2. For all types of signs, these products are suitable for use with a 12 VDC, R/C (UYMR2) Class 2 power supply.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
4. These products are suitable for use in dry, damp, and wet locations.
5. Lead wires do not have a voltage rating and are not R/C AVLV2 wiring. Lead wires must be separated from circuits of other
voltages in the end application.
6. Each 96 LED rope is rated Class 2, 12, 15, 24 VDC, 0.5A.
LED Lighting Modules, Cat. No. OS-LM10A-X, where X may be replaced with any letters of the alphabet A through Z, or any
number from 0 through 9, or any combination of letter and numbers representing different LED colors.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Each Class 2 LED Illumination module is rated for a maximum 86.4 W. When units are connected to a Class 2 circuit, their total
length is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2
circuit.
4. These products are suitable for use in dry, damp, or wet locations.
LED Lighting Modules, Cat. No. OS-LM10A-X, where X may be replaced with any letters of the alphabet A through Z, or any
number from 0 through 9, or any combination of letter and numbers representing different LED colors.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Each Class 2 LED Illumination module is rated for a maximum 86.4 W. When units are connected to a Class 2 circuit, their total
length is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2
circuit.
4. These products are suitable for use in dry, damp, or wet locations.
LED Lighting Modules, Cat. No. OS-LM11A-X where X may be replaced with any letters of the alphabet A through Z, or any
number from 0 through 9, or any combination of letter and numbers representing different LED colors.
1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Each Class 2 LED Illumination module is rated for a maximum 86.4 W. When units are connected to a Class 2 circuit, their total
length is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2
circuit.
4. These products are suitable for use in dry, damp, or wet locations.
Class 2 lighting assembly, , "LINEARlight POWER FLEX" , Model LM10P/W3-xxx, where xxx may be replaced with any letters
of alphabet A through Z and any numbers 0 through 9 or combination of letter and numbers.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 Lighting Assemblies, “LINEARlight POWER FLEX”, model no. LM10P/W3-xxx is each rated max. 75 Watts per unit.
When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 lighting assembly, , Model "HF2Chain/36/W3/865-12ft".
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Lighting Assemblies, Model "HF2Chain/36/W3/865-12ft" is each rated max. 53 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Electric discharge ballast and lamp system, Model ballast QT1x100ICE/UNV-T with Model ICE70 or ICE100 lamp, or Model
ballast QT1x150ICE/UNV-T with Model ICE100 or ICE150 lamp.
1. The Osram Sylvania Inc. lamps designated ICE70, ICE100, or ICE150 may be used in an electric sign lamp compartment that is
not an electrical enclosure.
117
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. Lamp leads nearest the lamp (as measured from core of first inductor) may have a maximum exposed length of 4in (102mm)
inside a lamp compartment or sign body. The remaining length of lamp lead wire shall be enclosed in conduit, raceway or
electrical enclosure. Note that the lamp inductor coils and wires between inductor coils that are taped to the lamp do not require
any additional enclosure.
3. The lamp and wiring within the lamp compartment shall not get wet during the Water Exclusion Test.
4. Thermal spacings of 9 inches (229mm) from any surface of the lamp to the sign face or sign body made of plastic, wood, or
laminated metal structural materials with a wood or plastic core. A clearance of 7 inches (178mm) may be used if a light
diffuser/heat barrier is located between the lamp and the plastic or wood product material. A light diffuser/heat barrier shall not
have openings exceeding 3/4 inch (19.1 mm) in any direction and has an opening-to-metal ratio not exceeding 1:1. The
minimum spacing between lamps when more than one is provided is 14 inch (356mm).
5. In lieu of the above thermal spacings, reduced lamp spacings may be used provided a Temperature Test is be conducted at the
reduced lamp spacings.
6. Grounding of the lamp metal mounting feet and ballast is required. The lamp shall be supported by the mounting feet provided.
7. The Osram Sylvania Inc. electric discharge ballasts QT1x100ICE/UNV-T or QT1x150ICE/UNV-T shall be mounted inside an
electrical enclosure or raceway.
8. The lamp and ballast are for use in dry or damp locations inside an indoor or outdoor sign.
LED Lighting Modules, Cat. No Models BLP/BL02/W-XY-QQQ, BLP/QQQ/BL02-ZX (Backlight 2GBL02), where X - any no.
for model color version (0-9), Y - binning category (A-Z), Z - LED color (A-Z), QQQ- color temperature 000-999.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 V DC or less power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. These LED modules can be interconnected together with rated max. 22 Watts. When these units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Module, designated as LYCM/12V/XXX/IP66 series where Y may be 120, 160 or 180 and XXX may be any
alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. These products are each rated max. 1.2 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Module, Models LFO5A, followed by suffixes and LXXLFE/24V/YYY/TP/G2/A, LFO5E, followed by suffixes and
LXXLFE/24V/YYY/TP/G2/E; LF06P, followed by suffixes and LXXLFE/24/YYY/PF/G2, where YYY represents color temperature
(white) or wavelength (monochromatic color)and XX represents wattage. The YYY and XX can be any number or letter. Suffixes
represent color temperature or wavelength.
1. The sign accessory LED strips are suitable only for connection to a 24VDC Class 2 voltage source.
2. The products may be used in a dry, damp, or wet location without additional enclosure.
3. The mounting means is not specified and may include mechanical fasteners or double sided adhesive tape.
Class 2 LED Module, designated as BA01LA-XXX-YYY, BA01MA-XXX-YYY, BA01MA-ZZ, BA01SA-XXX-YYY, BA01SA-ZZ, and
BX03BA-XXX-YYY Series and Class 2 LED Modules, designated as L150/X2/12V/XXX, L125/X2/12V/XXX and L200/X2/12V/XXX.
1. These products are only suitable for connection to a Class 2 power source and rated as follows: 12 Volt DC or less. The LED
modules with the prefix BA or BX have only been evaluated for a max 12 Volts DC or less. The LED Modules with the prefix L
have only been evaluated for a max 12.5 Volts DC or less.
2. These products are each rated max 3.8 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated as follows:
The LED modules with the prefix BA or BX have only been evaluated for a max 12 Volts DC or less.
The LED Modules with the prefix L have only been evaluated for a max 12.5 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Dimmable Class 2 LED Drivers, Models OT96W/24V/UNV/DIM and OT96W/24V/UNV.
1. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations.
3. The product was tested for use at the maximum ambient temperature (Tma) of 40 C permitted by the manufacturer's
specification.
4. In the end product, power supplies shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less
than 4 inches (102 mm) apart when arranged otherwise.
5. Model OT96W/24V/UNV/DIM is provided with a Dimming circuit. Dimming of the outputs is by using a potentiometer. The
dimming circuit leads to the potentiometer are considered Class 2.
6. The suitability of grounding connection shall be determined in the end-use product.
Class 2 LED Module, Models L144/12V/865, L096/12V/RED, L096/12V/GRE, L096/12V/BLU.
1. These products have been evaluated for connection to a Class 2 power source only, rated 12 Vdc, 60 W max.
2. These products are suitable for use in dry, damp or wet locations.
3. The LED module is provided with leads for interconnection. The suitability of the leads shall be determined in the end product.
Class 2 LED Module, Cat. Nos. MOD3528-3-1, MOD5630-6-1, MOD5630-6-2, MOD5630-8-1.
1. These LED modules are each rated as noted in the electrical ratings tables. Input test for each LED module should be
considered in end products.
January 23, 2014
118
SIGN COMPONENTS MANUAL (SAM)
2. The suitability of the electrical construction shall be determined in the end use.
3. The suitability of the mounting means shall be determined in the end use.
4. PWB is metal based, rated V-0, 130 C. Temperature testing shall be conducted in the end product.
5. Suitability for use in environmental locations shall be considered in the end product.
Class 2 LED Module, Model Series HF2 Chain X4.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by adhesive. Suitability of the mounting means shall be determined
in the end product
LED Strip Class 2 LINEARlight Flex Protect, LF05A-W3F-xxx-P and LF05A-W3F-xx-P.
1. Manufacturer’s name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, or model number/series in min. 2.4mm high letters and visible during installation.
4. Class 2 input only.
5. Input voltage and current.
6. Suitable for Dry or Damp locations.
LED Strip Class 2 LINEARlight POWER Flex, LF06P2-W5F-xxx.
1. Manufacturer’s name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, or model number/series in min. 2.4mm high letters and visible during installation.
4. Class 2 input only.
5. Input voltage and current.
6. Suitable for Dry or Damp locations.
LED Strip Class 2, LINEARlight POWER Flex Protect, LF06P-W4F-xxx-P.
1. Manufacturer’s name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, or model number/series in min. 2.4mm high letters and visible during installation.
4. Class 2 input only.
5. Input voltage and current.
6. Suitable for Dry or Damp locations.
LED Strip Class 2, LINEARlight Flex Short Pitch, LF06S-W3F-xxx.
1. Manufacturer’s name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, or model number/series in min. 2.4mm high letters and visible during installation.
4. Class 2 input only.
5. Input voltage and current.
6. Suitable for Dry or Damp locations.
LINEARlight Flex Advanced, LF06A-XXX-YYY, where X and Y maybe any letter, number or blank.
1. Manufacturer's name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, model number or series name in min. 2.4mm high letters and visible during installation.
4. Electrical ratings:
Model
LF06A-XXX-YYY
Input Voltage
(Vdc)
Max.
Wattage (W)
Max. Current
(A)
Max. #
LEDs
Max. Total Length
(m)
24
48
2
600
10
5. Suitable for Dry or Damp locations.
6. Class 2 Input Only.
LINEARlight Colormix Flex Protect, LF05CX-XXXX-P, where X maybe any letter, number, or blank.
1. Manufacturer's name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, model number or series name in min. 2.4mm high letters and visible during installation.
4. Electrical ratings:
Model
Input Voltage
(Vdc)
Max.
Wattage (W)
Max. Current
(A)
Max. #
LEDs
Max. Total Length
(m)
24
72
3
200
6
LF05CX-XXXX-P
5. Suitable for Dry or Damp locations.
6. Class 2 Input Only.
LINEARlight Flex Value IP, VI05A-W3-XXX, where X maybe any letter, number or blank.
1. Manufacturer's name, trade name, or trademark in min. 2.4mm high letters and visible during installation.
2. The date or other dating period of manufacture in min. 2.4mm high letters and visible during installation.
3. Distinctive catalog, part, model number or series name in min. 2.4mm high letters and visible during installation.
4. Electrical ratings:
Model
VI05A-W3-XXX
Input Voltage
(Vdc)
Max.
Wattage (W)
Max. Current
(A)
Max. #
LEDs
Max. Total Length
(m)
24
25
1
300
6
5. Suitable for Dry or Damp locations.
119
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
6. Class 2 Input Only.
LED Strip Class 2, LINEARlight Flex Series – LF05E-P.
1. These products have been evaluated for use with a suitable Class 2, 24 VDC; power source only.
2. These products have been evaluated for use in dry and damp locations.
3. Thermal spacings shall be provided in accordance with Standard UL 48 or the following tests should be considered in the end
use application: Normal Temperature, and Dielectric Voltage Withstand Test.
4. The LED strips may be mounted by integral tape or other mechanical means.
5. Installation Instructions indicate that the LED Strips may be cut to size in areas marked by straight edge symbol.
Class 2 Power Supply, Models OT10W/350C/120-240V, OT10W/12V/120-240V and OT25W/12V/UNV.
1. The electrical ratings are as follows:
Input, 60 Hz
Output, ac
Model
V
A
V
A
VA or Pmax
OT25W/12V/UNV
85-277
0.11-0.3
12
2.0
25 Pmax
OT10W/12V/120-240V
120-240
0.175-0.120
12
0.833
10 VA
OT10W/350C/120-240V
120-240 0.175-0.120 2.3-28 0.350
10 VA
2. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
3. A suitable Fire and Electrical Enclosure shall be provided in the end product.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. These power supplies are only suitable for use in dry and damp locations.
Class 2 Power Supply, Model OT60W/12V/UNV.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. The electrical ratings are as follows:
Input, 60 Hz
Model
OT60W/12V/UNV
Output, DC
V
A
V
VA
100 - 277
0.8 - 0.3
12
60
3. These power supplies are only suitable for use in dry and damp locations.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 LED Module, designated as BA03MA-XXX-YYY and BB03-LA-XXXYYY series, where XXX may be blank or W4F, and
YYY may be a combination of any alphanumeric characters.1. These products are only suitable for connection to a Class 2
power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Module, designated as BX12BA-W4F Series.
1. These products are only suitable for connection to a Class 2, 24Vdc power source only.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Module, designated as BX06BA-W4F Series.
1. These products are only suitable for connection to a Class 2, 24Vdc power source only.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Strip, LINEARlight Colormix Flex, LF05CA2-RGB3.
1. These products were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2
source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
4. These products have been evaluated for use in dry and damp locations.
Class 2 LED Strip, LINEARlight POWER Flex® Protect G2, LF06P2-XXX-YYY-P.
1. These products were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2
source.
January 23, 2014
120
SIGN COMPONENTS MANUAL (SAM)
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
4. These products have been evaluated for use in dry and damp locations.
Class 2 LED Strip, LINEARlight Flex® Protect ADVANCED G2, LF06A-XXX-YYY-P.
1. These products were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2
source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
4. These products have been evaluated for use in dry and damp locations.
OUTWATER PLASTICS INDUSTRIES INC
24 RIVER RD
PO BOX 500
BOGOTA, NJ 07603
E343812
Class 2 LED Module, designated 5050Ux3-B-02-21-12VW, 5050Ux3-B-04-07-12VW, with or without the suffix "-Cree", where x
can be R, Y, G, B, WC, or WY.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volts DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 VDC.
3. Class 2 LED Modules Cat. ZLS-PCB-X Series, ZLS-PCBC-X Series, PL1-PMBC-X Series and ZLS-PMBC-T Series are each
rated max. 3 watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the
secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 VDC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products are for factory wiring only in sign or outline lighting related application.
Class 2 LED Module, designated TMX-300/300-A, TMX-300/100-B, TMX-300/050-C, TMX-300/060-D, TMX-100/060-E, TMX050/060-F, TMX-300/300-A2.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volts.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are suitable for use in dry and damp locations.
4. These products are for factory wiring only.
5. The suitability of mounting means shall be determined in end product use.
PAIGE ELECTRIC CO L P
1160 SPRINGFIELD RD
PO BOX 368
UNION, NJ 07083
E339010
Polymeric neon electrode end cap with GTO cables, "Paige 98/1298/1514/3840 GTO System".
1. These devices are rated max. 7500 V ac to ground. May be used with 15 kV mid-point grounded transformers.
2. These products are suitable for use in dry or damp locations.
3. These products are required to be enclosed or protected from the weather.
4. All integrally sleeved GTO cables indicated as suitable for use with the neon electrode enclosures covered by this report shall
have a temperature rating of min. 135°C for dry and damp locations.
5. These products are only for use in Listed signs and Sections of signs and are not suitable for field installed skeletal neon or
outline lighting.
6. The units shall be subjected to a high voltage Dielectric Strength Test in the end product.
7. These components were evaluated for use with the Listed GTO cables made by Paige Electric Co L P, Type GTO-15, rated 15
kV. Use with any other GTO type or manufacture will need to be evaluated in the end product.
Sign accessories, Ventex 600VDC max LED cable designated as VA-W09CNR.
1. These devices are rated max. 600VDC.
2. These products are suitable for use in dry or damp locations.
3. These products are required to be enclosed or protected from the weather.
4. These products are only for use in LED Listed signs and Sections of signs and are not suitable for field installed skeletal neon or
outline lighting.
6. The units shall be subjected to a high voltage Dielectric Strength Test in the end product.
7. These components were evaluated for use with for use only with VENTEX LED products. Use with any other LED type products
or manufacturer will need to be evaluated in the end product.
PALRAM AMERICAS INC
ARCADIA WEST INDUSTRIAL PARK
9735 COMMERCE CIR
KUTZTOWN, PA 19530
E336663
Rigid Sign Face Materials, designated Palsun, Palsun SG and Palsun CS.
1. These materials are acceptable for applications of sign enclosures, sign bodies, and decorative parts. For enclosure
applications, these materials may be located no closer than 0.8 mm to any uninsulated live part.
121
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. The materials have a use temperature of 80°C. If a heat producing component such as electrode, transformer or ballast is
located within 1 inch of the material, a temperature test should be conducted in the end product.
3. Marking - The following markings or equivalent shall be provided. Markings A and B below shall be marked anywhere where
readily visible during servicing.
A. "Do not attempt to repair or service a damaged sign face. For servicing of this sign, contact ____.” (Blank to be replaced by
Applicant's Company name, City and State.)
B. "Replace only with ___ , Type ___ ." (Blanks to be replaced by Applicant's Company name and material Type or
designation.)
4. The materials are suitable for use as an enclosure of an indoor or outdoor sign and have been evaluated for ozone resistance
and UV exposure.
5. All materials must be a minimum of 0.12 in. (3.0 mm) thick to comply as a sign enclosure. All testing should be repeated if the
thickness of the sheet is reduced to less than 0.12 in. (3.0mm).
6. All materials have been investigated for and comply with the termination of conduit, electrode housings or the like.
7. All materials have been approved for component support when components are secured by nuts and bolts.
8. The suitability of the securement system for the materials to prevent the entrance of water, which may contact live parts within a
sign in outdoor sign applications, shall be determined.
9. When the material is relied upon for the mounting of the sign and/or sign components, the material shall be subjected to the
mounting means test in the end product.
10. Only one side of the plastic sheets are UV coated. Therefore, the UV coated side shall be placed such that it is the exterior
surface of the sign.
11. Testing for exposure to live parts was conducted on the non-UV coated side of plastics. Thus, the non-UV coated side shall be
the only side exposed to live parts.
12. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed
to the interior of the sign. This may be accomplished with channels, flanges or other suitable mechanical means.
PARMIDA LLC
801 E WASHINGTON BLVD
LOS ANGELES, CA 90021
E362583
Class 2 LED Modules, designated as XXXX YYYYD/M series, where XXXX and YYYY may be combinations of any numbers.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuits.
3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secondary
or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
PERMLIGHT PRODUCTS INC
422 W 6TH ST
TUSTIN, CA 92780
E213411
Class 2 LED Illumination, Cat. Nos.700 Series, 752 (“Twister\’r”) or PCSA01, 760-2, 760-3, 765-4, 750-5, 750-9, 711-2, 780
Series, TINY2, PX Series.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, 700 Series is rated 0.6 Watts per unit, Cat. No. 750-9 is rated 1.44 watts per unit, Cat. No. 750-5 is
rated 0.6 watts per unit, Cat. No. 760-3 is rated 0.48 Watts per unit, Cat. No. 752 or PCSA01 is rated 0.6 per unit, and Cat. No
765-4 is rated 0.6 per unit and Cat. No. 711-2 is rated 0.6 Watts per unit, Cat. No. TINY2 is rated 0.4 Watts per unit. When
units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of
the Class 2 supply and 60 watts per Class 2 circuit.
4. Class 2 LED Illumination, 700 Series and Tiny2 are provided with a R/C wire soldered on the printed wiring board for
connection in series.
5. Cat. No. 750-9, 750-5, 760-3, 752 or PCSA01, 765-4 and 711-2 Series are provided with R/C wire soldered on the printed
wiring board for connection in series.
6. These products are suitable for use in dry, damp and wet locations.
7. These products are not required to be enclosed or protected from weather.
Class 2 LED Illumination, Model No. 711-18DL.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, 711-18 DL module is rated 60 Watts per unit. When units are connected to a Class 2 circuit, they are
not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit.
4. Cat. No. 711-18 DL modules are provided with R/C wire soldered on the printed wiring board for connection.
5. These products are suitable for use in dry, damp and wet locations.
6. These products are not required to be enclosed or protected from weather.
Photocell, Model PL746-TPC "Photocell".
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, “Photocell” PL746-TPC is rated max. 60 Watts per unit. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts
per Class 2 circuit.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
122
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from weather.
Class 2 LED Illumination, Cat. No. 780 or PCSK01.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, 780 or PCSK01 Series, Palette Light and Palette Light Mini are each rated max. 0.78 Watts per unit.
When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply and 60 watts per Class 2 circuit.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from weather.
Class 2 LED Illumination, Model No. Elblanco/Delta Light PML900 Series.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, “Elblanco/Delta Light” PML900 Series are each rated max. 10 Watts per unit. When units are
connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
supply and 60 watts per Class 2 circuit.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from weather.
Class 2 LED Illumination Module, Cat Nos. "PZ" or PCSC01, "AB", PCSC02 or PCSC03 or 727-XXX Series, where XXX may
be any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V.
3. Class 2 LED Modules are rated max. 1.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Illumination, Model No. 737 ("Twister Nano"), 747 ("el Plato"), 753 ("Twister STAR"), 777 ("Twister Nitro"), 787
("Twister Halo") Series. All catalogue numbers may be followed by WWXYZ; where WW may be replaced with any letters of
alphabet AA through ZZ; X may be replaced with any letter of alphabet A through Z or may be left blank, Y may be replaced with
any letters of alphabet A through Z or may be left blank and and Z may be replaced with any letters of alphabet A through Z or may
be left blank.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 12 V.
3. Class 2 LED Modules, Cat. No. 737 (“Twister Nano”), 747 (“el Plato”), 753 (“Twister STAR”), 777 (“Twister Nitro”) and 787
(“Twister Halo”) series are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Module, Designated As "Omnistar" or "PFSC2520".
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. These products are each rated max. 0.9 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Module Designated As “Cayenne for Signs” or “PFS4820”.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. These products are each rated max. 1.2 watts per module. When units are connected to a Class 2 circuit, they are not to draw
a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
LED Class 2 Power Supply, Cat. Nos. 60-12D-A.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary
and secondary circuits.
LED Power Supply with Class 2 outputs, Models 250-12DC-DIM, 250-12DC-DIM-240, 250-12DC-DIM-277, 250-12DC, 250XXXDC(a), 250-12DC-277, 250-12DC-240, PCDK01, PCDK02, PCDK03, PCDK04 and P8675.
123
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
1. These products are suitable for dry and damp locations.
2. These Led Drivers do not need to be enclosed in the end product.
3. The output(s) of these LED drivers comply with the criteria for Class 2 output.
LED Power Supply with Class 2 outputs, Models 60-XXXD, 60-XXDC, 60-XXDC-DIM, 60-XXD-U, 37-XXXDC-DIM, 37-XXDC,
XX can be any number from 00 to maximum 12 indicating output DC voltages.
1. These products are intended for use only in applications that comply with the requirements of the end product.
2. When marked as suitable for use in damp locations, these products are to be installed where protected from rain, snow and
water spray by water shield or sign body.
3. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least
150 mm (6 in) inside.
4. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 2 inches.
5. Leakage current test shall be conducted if used in a portable end product.
LED Power Supply with Class 2 outputs, Model 20-12DC-A-100277.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief on input lead construction and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. When conducting temperature test in the end product, the maximum temperature on the enclosure (case) shall not exceed
80C. When provided with alternate enclosure material R/C (QMFZ2), Teijin Chemicals Ltd. (E50075), Material designation
LN-1250G, the maximum temperature on the enclosure (case) shall not exceed 90°C.
LED Power Supply with Class 2 outputs, Model 40-12DC-A-100277.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105C. Output leads are Style 1430, No. 18 AWG, rated VW-1,
300 V, 105C. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated on input lead construction. The suitability of the enclosure as
ultimate enclosure shall be determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-0 and the necessity of additional fire barriers shall be determined in end product.
Class 2 Letter Signs Cat. Nos. Model 800 Series.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. Class 2 LED Illumination, “Photocell” PL746-TPC is rated max. 60 Watts per unit. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts
per Class 2 circuit.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from weather.
LED Drivers, Model No. PCDH03, PCDH05.
1. The output of these LED drivers comply with the criteria for Class 2 output.
2. The product is suitable for use in dry or damp locations.
3. The product shall be enclosed in the end product in a suitable electrical, mechanical and fire enclosure.
4. The mounting means on metal housing is considered as grounding means.
5. The product is intended to be connected to max. 20 A branch circuit.
6. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
7. The input/output leads on these products are for factory connection only, not for Field Wiring. The suitability of the wiring is to
be determined in end product.
8. The input leads were not provided with strain relief means, the suitability is to be determined in end product.
9. The LED driver has electrical rating below:
Input (AC)
Output (DC), Loaded
Cat. No.
Voltage
Current
Frequency
Voltage
Current
PCDH03
90-240
1.4 A
max.
50/60 Hz
12 V
5.0 A
PCDH05
120-277
1.1 A max
50/60
12V
5.0
10. The Tc shall not exceed 75°C for Model PCDH05.
Class 2 LED Module, Cat. Nos. PFSC16, PFSC17, PFSC18.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 12 V.
3. Model PFSC16 is rated 66 W, Model PFSC17 is rated 66W and Model PFSC18 is rated 66W. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Class 2 Power Supply, PS60-12V-108264-DE, PS35-12V-108264-DE, PS15-12V-108264-DE.
January 23, 2014
124
SIGN COMPONENTS MANUAL (SAM)
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Input Voltage
(V)
Input Freq
(HZ)
Input
Current (A)
Power
Factor
PS60-12V-108264-DE
120-240
50/60
0.75
0.95
12
5.0
60
PS35-12V-108264-DE
120-240
50/60
0.39
0.95
12
2.92
35
PS15-12V-108264-DE
120-240
50/60
0.35
0.4
12
1.25
15
Model No.
Output
Output Current
Output
Voltage (V dc)
(A)
Power (W)
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in suitable electrical enclosure in the end product.
5. These products are suitable for factory wiring only.
6. The load powered by the Class 2 output of these power supplies at the 12 Vdc rating or less is suitable for use in dry, damp
and wet locations.
7. These products have been tested in oven at 50ºC ambient, with the following maximum case temperatures, Tc:
For model LCU 060/12 D the Tc = 82ºC; for model LCU 035/12 D XX the Tc =64ºC; for model LCU 035/12 D XX the Tc=74ºC.
8. These products are intended for use in a dry or damp locations only.
9. The suitability of input/output leads and the wring shall be determined in end product use.
10. The metal case of Model LCU 015/12 D is not grounded. The proper grounding means of this product shall comply with the
end product requirements.
Class 2 LED Module, designated as "PCSN01".
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 24
Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 LED Module, designated as "PCSF02".
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12.5
Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 LED Module, designated as "PCSD02".
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 30
Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 LED Module, designated as “STAR 2.0”.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12.5
Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
LED Class 2 Power Supply, Model PCDM03.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of two Class 2
output.
2. These products are provided with the following electrical ratings:
Model
Input (V, Hz, A, W)
Max Output (V, A, W)
PCDM03
100-277; 50-60; 1.7; 150
12.0; 5.0; 60
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end,
and 101.6 mm (4 in.) from side to side.
4. The suitability of input/output leads and the wring shall be determined in end product use.
5. These products are constant voltage type that requires the proper number of LED modules and controllers that do not exceed
the maximum output current.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. These LED drivers are intended for use in fixed equipment only.
8. These products are suitable for dry, damp and wet locations.
9. These LED drivers do not need to be enclosed in the end product.
10.These products were temperature testes at an elevated ambient of 50°C.
LED Tube Lamps, designated “PFXXXHO2S Series”, where XXX is the length in inches 24-120.
1. The Temperature Test was conducted with the LED Tube Lamp, Model PFXXHO2S installed in Listed fluorescent signs having a
maximum of 2, ten-foot lamps, where the lamps were spaced 1-1/2 inches apart. If the device is used in a different product or
configuration, consideration shall be given to re-conducting the Temperature Test.
2. The LED Tube Lamps have been evaluated for use in dry and dump locations. The use in other environments shall be
considered in the end product.
125
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. The Risk of Shock (Pins) was not performed since these lamps are provided with integral leads for connection to a separate
external LED driver. The end caps are provided with grooves for mechanical support only.
4. Consideration for suitable installation is to be determined in the end-use application.
5. The need for additional end product markings, such as lamp replacement, shall be considered in the end product evaluation.
6. The Normal and Abnormal Operation on Dimmers test has not been conducted. The need for these tests should be considered
when the device is connected to a dimmer in the end use.
7. The mounting means of these products shall be determined in the end product applications.
Class 2 LED Module, Models “PCSG01” and “PCSQ01”.
1. These products are suitable for use in dry, damp and wet locations when supplied with a Class 2 power source rated 25 Volt DC
or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
5. These products are provided with the following maximum Class 2 input electrical ratings:
Model No.
Max. Input Voltage
Max. Input Current
Max. Power
PCSG01
25 Vdc
0.4 A
10 W
PCSQ01
17 Vdc
5A
85 W
Class 2 LED modules, designated as "PCSK03" and "PCSD02".
1. Manufacturer's name, trade name, or trademark.
2. Distinctive catalog or model number.
3. The electrical ratings.
4. Factory ID identifying the product to a particular factory if produced at more than one manufacturing location.
Class 2 LED Controller, Model PCDH04.
1. These products are only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated max 12
VDC.
2. These products are rated per the Table below. When the units are connected to the Class 2 supply, their loads are to be limited
to draw a total power or current of no greater than the output power or current rating of the Class 2 power supply.
Model
PCDH04
Input - Class 2
Max. Vdc
Max. Idc
12
5
Output -Class 2
Max. Vdc Max. Idc Max. W
12
5
60
Number of
Output
1
3. These products are suitable for use in dry and damp locations.
4. These controllers are provided with a maximum of one Class 2 output.
5. These products are suitable for factory wiring only.
Class 2 LED Modules, designated as "PCSD05".
1. These products are suitable for use in dry, damp and wet locations when supplied by a Class 2 power source rated 12.5 Volt DC
or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
PERSONA INC
700 21ST ST SW
PO BOX 210
WATERTOWN, SD 57201
E327541
Sign Face Tensioning Systems, designated Flex Retro Retainer S-9061, Bleed Flex Retro S-9130, Double Hinge Filler S-9170,
Hinge Filler S-9144, Aluminum Spacer 5052-H32, Flex Retro Cover S-9131, Flex Retro Cover S-9072, Flex Retro H-9064, Flex
Tensioning Bar S-9062, Wedge Clamp.
1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent
entrance of water in outdoor sign applications shall be determined in the end product.
2. This product may be used in dry, damp, or wet locations.
3. Tensioning bar fasteners shall be spaced in the end product as described in the Installation Instructions.
4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent
billowing.
5. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face
requirements of UL 48,particularly clearance to lamps and lampholders.
6. These clips have been determined to be suitable with any R/C Flexible Sign Face Material al least 0.020” (0.51mm) thick.
Suitability for use with a material of lesser thickness shall be determined in the end product.
PHILIPS LIGHTING BV
KANTSINGEL 24
5349 AJ OSS, THE NETHERLANDS
E211810
LED power supply with Class 2 outputs, Model 9137 006 208.
1. Model 9137 006 208 is rated for a 100-240 Volts, 50/60 Hz, 25 Watt input and a 24 V DC, 0.83 amp, 20 Watt output.
2. These components are intended for use in dry locations only when not potted. When potted, they are suitable for use in damp
locations.
3. These power supplies need to be installed in an enclosure with a means for connection to conduit.
January 23, 2014
126
SIGN COMPONENTS MANUAL (SAM)
4. A Temperature Test is not required of the power supply when installed in an enclosure having dimensions greater than 13.5 by 6
by 4 inches. When installed in a smaller enclosure and a Temperature is required, the maximum temperature on the output
transformer by thermocouple is 90°C.
5. The Class 2 output of these LED power supplies are acceptable for use in a damp and wet location.
LED power supply with Class 2 outputs, Model 913710052466.
1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp
locations.
2. These power supply needs to be installed in an enclosure with a means for the connection to conduit.
3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110° C.
4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location
Power supply with Class 2 outputs, Model 9137006209.
1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations.
2. These power supply needs to be installed in an enclosure with a means for the connection to conduit.
3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than
13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C.
4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location.
PHILIPS LIGHTING ELECTRONICS N A
OHARE INTERNATIONAL CENTER
10275 W HIGGINS RD
ROSEMONT, IL 60018
E220165
LED Array Drivers, Models 9137 005 34302, LED120A0700C24F, LED120A0350C33F, LED120A0024V07F,
LED120A0012V10F, LED120A0350C28FO, LED120A0700C24FO, GEXNPS31-120, LED120A0350C33F and
LED120A0350C33F.
1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. The LED Drivers listed below are suitable for use in Dry and Damp locations: LED120A0012V10F, LED120A0350C28FO,
LED120A0700C24FO, LED120A0350C33F and GEXNPS31-120.
4. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 25°C. except the
Models LED120A0350C28FO, LED120A0700C24FO, LED120A0012V10F, 913700534302, LED120A0350C33F and
GEXNPS31-120 were tested for a 69.1 deg. C ambient for a max. Tcase temperature of 90 deg. C.
5. This unit is provided with a Class 130 (B) insulation system. A temperature test is required when the unit is installed within an
electrical enclosure or raceway.
6. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the
LED driver is used in combination with other equipment in the end-use product.
7. The unit is intended for installation inside an electrical enclosure.
8. The Models LED120A0350C28FO, LED120A0700C24FO, LED120A0012V10F and GEXNPS31-120 may be used within an
electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side
to side from adjacent LED power supplies.
LED Drivers, Models, GEXNPS30-120, LED120A0024V10D, LED120A0024V10F, LED120A0024V18F, LED120A0024V18FO,
LED-120A-0024V-14-F-O, LED277A0024V18F, LED120A0012V21F, LED120A0024V33F, LED120A0012V50F, and GEXLPS21,
LED120A1400C24F and LED-120A-0024V-14-F-O.
1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40(C. Model
LED120A0024V18FO was found suitable for 55 C ambient.
3A. Cat. No. LED277A0024V18F was submitted and tested for a maximum manufacturer’s recommended ambient (Tmra) of 60°C.
4. When used in portable equipment leakage current must be considered. The table below shows the maximum leakage current
measured and maximum number of drivers that can be used without conducting leakage current test:
Input, 60 Hz
Max. No of drivers
Volt (V)
Leakage MIU
Model
per portable unit
LED120A0024V10F
120
0.001
10
LED120A0024V10D
120
0.001
10
LED120A0024V18F
120
0.001
10
LED120A0024V18FO
120
0.001
10
LED-120A-0024V-14-F-O
120
0.001
10
LED120A1400C24F
120
0.001
10
LED120A0012V21F
120
0.001
10
LED120A0012V50F, GEXLPS21
120
0.220
2
LED120A0024V33F, GEXNPS30-120
120
0.235
2
5. The drivers are intended for installation inside an electrical enclosure.
6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
7. ONLY the following drivers were found suitable for use in DAMP location:
Models GEXNPS30-120, LED120A0024V33F, GEXLPS21-230V, LED120A0024V33F, LED120A0012V50F,
LED120A0024V18FO, LED-120A-0024V-14-F-O, and GEXLPS21.
8. The Model LED120A0024V10D has a Class 2, 0-10 V dc output for dimming purposes. Two output terminals are provided for
connection to an optional dimmer control.
9. Model LED120A0024V18F0 was submitted and tested for a max manufactures recommended T case of 85ºC.
10. Model LED120A0024V33F was submitted and tested for a max manufactures recommended T case of 85ºC.
127
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
LED Drivers, Models LED120A0880C19FO, LED120A0880C19DO, LED120A0700C24DO.
1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310,
Fourth Edition, which would cover the component itself if submitted for Listing.
2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40(C.
4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an
electrical enclosure or raceway.
5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the
LED driver is used in combination with other equipment in the end-use product.
6. The unit is intended for installation inside an electrical enclosure.
7. The Model may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer
than 1 in. end to end or 4 in. side to side from adjacent LED power supplies.
8. Models LED120A0880C19DO and LED120A0700C24DO has a Class 2, 0-10 V dc output for dimming purposes. The two
dimming output leads are gray and violet, provided for connection to a dimming controller.
9. The Dimmer Controller must be either a 100K Ohms Potentiometer or a standard 0-10V DC dimmer switch, which is not
provided by the manufacturer.
10. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
LED Drivers, Models LED120A0700C28FO, LED120A0700C28DO, LED277A0700C28FO and LED277A0700C30DO.
1. This component has been judged on the basis of the required spacings in the Standard for Electric Sign Component, UL 879,
Eighth Edition, which would cover the component itself if submitted for Listing.
2. This unit is provided with a Class 105(A) insulation system.
3. The unit is intended for installation inside an electrical enclosure.
4. The unit was submitted and tested for a maximum manufacturers recommended ambient of 40(C. If adjacent LED power
supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be conducted in the end use
product.
5. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
6. The Violet (Positive) and the Gray (Negative) leads provided on model LED-120A-0700C-28-DO are intended for use with a 010 V DC type Dimmers.
7. The secondary output of all models and the 10V DC dimmer circuit of the Model LED-120A-0700C-28-DO are considered to be
Class 2 circuits.
LED Drivers, Model Nos. GEXLPS21-U, LEDINTA0012V50FO.
1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth
Edition, which would cover the component itself if submitted for Listing.
2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40(C.
4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an
electrical enclosure or raceway.
5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the
LED driver is used in combination with other equipment in the end-use product.
6. The unit is intended for installation inside an electrical enclosure.
7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer
than 1 in. end to end or 4 in. side to side from adjacent LED power supplies.
8. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
LED Drivers, Models LEDINTA0024V28FO, GEPS24-100 and GEPS24-100U
1. These LED Drivers have been evaluated to comply with Class 2 output criteria.
2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors.
3. These LED Drivers are only suitable for use in Dry and Damp Locations.
4. These products are rated as follows:
Input, 60 Hz
Model
Volt/V
Amp/A
Power/W
OUTPUT V and
Amperes DC
LEDINTA0024V28FO
120/277
0.66/0.30
67
24V and 2.8 (*)
GEPS24-100, GEPS24-100U
120/277
1.00/0.40
100
24V and 4.1 (**)
(*) - For connection to LED array consisting of 67 Watt maximum.
(**) - For connection to LED array consisting of 100 Watt maximum.
5. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure and mounted not closer than 1 in. end to end or 4 in. side to side from
adjacent LED power supplies.
6 The units were submitted and tested for a maximum manufacturers recommended ambient of 52.7°C with corresponding
maximum case temperature Tc of 90C for Cat. Nos. LED-INTA-0024V-28FO, GEPS24-100, GEPS24-100U. If adjacent LED
power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be conducted in the end use
product.
LED Drivers, Model LED-120A-0024V-41-RD.
1. These LED Drivers have been evaluated to comply with Class 2 output criteria.
2. Suitability for the unit to be installation inside an additional electrical enclosure shall be determined in the end used product.
3. These LED Drivers are only suitable for use in Dry and Damp Locations.
4. The unit were submitted and tested for a maximum manufacturers recommended ambient of 40 C. If adjacent LED power
supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be conducted in the end use
product.
5. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be
provided.
January 23, 2014
128
SIGN COMPONENTS MANUAL (SAM)
LED Drivers, Models LEDINTA0024V41FO, DCINTA0025V41FP, LEDINTA0024V41DLO, LED-INTA-0024V-41-F-LO, LED-INTA0024V-30-F-LO, LED-INTA-0024V-30-D-LO, LED-INTA-0024V-20-F-LO, LED-INTA-0024V-20-D-LO, LEDINTA0024V32FO,
LEDINTA0024V22FO, GE100/MV/V24T1-A, LEDINTA1600C36FO and LEDINTA0012V50FO, LEDINTA24V28FO,
GE060/MV/V12T1-A, GEPS12-60U, GEPS24-100U.
1. These LED Drivers have been evaluated to comply with Class 2 output criteria.
2. These LED Drivers are only suitable for use in Dry and Damp Locations.
3. These products are rated as follows:
Input, 60 Hz.
Volt/V
Amp/A
LEDINTA0024V41DLO
120-277
0.95-0.40
100
24V and 4.1 A(*)
LED-INTA-0024V-41-F-LO
120-277
0.95-0.40
100
24V and 4.1 A(*)
LEDINTA0024V41FO
120-277
0.95-0.40
100
24V and 4.1 A(*)
GE100/MV/V24T1-A
120-277
0.95-0.40
100
24V and 4.1 A(*)
GEPS24-100U
120-277
0.95-0.40
100
24V and 4.1 A(*)
DCINTA0025V41FP
120-277
0.95-0.40
100
24V and 4.1 A(*)
LED-INTA-0024V-30-F-LO
120-277
0.72-0.32
72
24 and 3.0 A(**)
LED-INTA-0024V-30-D-LO
120-277
0.72-0.32
72
24 and 3.0 A(**)
LED-INTA-0024V-20-F-LO
120-277
0.48-0.22
48
24 and 2.0 A(***)
LED-INTA-0024V-20-D-LO
120-277
0.48-0.22
48
24 and 2.0 A(***)
Model
Power/W OUTPUT V and Amperes DC
LEDINTA0024V32FO
120-277
0.75-0.35
77
24 and 3.2 A(+)
LEDINTA0024V22FO
120-277
0.50-0.25
53
24 and 2.2 A(++)
LEDINTA1600C36FO
120-277
0.55-0.25
58
36V and 1.6A #
LEDINTA0012V50FO,
GEPS12-60U,
GE060/MV/V12T1-A
120-277
0.60-0.29
60
12V and 5.0A ##
LEDINTA0024V28FO
120-277
0.66-0.30
67
24V and 2.9A(###)
4. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure and mounted not closer than 1 in. end to end or 4 in. side to side from
adjacent LED power supplies.
5. The units were submitted and tested for a maximum manufacturer's recommended Tc point described in the table below. If
adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be conducted
in the end use product.
Input Voltage,
Hz
Max. Case @
Tc, °C
Ambient, °C
(Reference only)(*)
LEDINTA0024V41DLO
120-277,60
85
61.5/63.2
LEDINTA0024V41FO
120-277,60
90
56.6/59
GE100/MV/V24T1-A
120-277,60
90
56.6/59
GEPS24-100U
120-277,60
90
56.6/59
Model No.
LED-INTA-0024V-41-F-LO
120-277,60
85
61.5/63.2
LED-INTA-0024V-30-D-LO
120-277,60
85
61.5/63.2
LED-INTA-0024V-30-F-LO
120-277,60
85
61.5/63.2
LED-INTA-0024V-20-D-LO
120-277,60
85
61.5/63.2
LED-INTA-0024V-20-F-LO
120-277,60
85
61.5/63.2
LEDINTA0024V32FO
120-277,60
90
56.6/59
LEDINTA0024V22FO
120-277,60
90
56.6/59
LEDINTA1600C36FO
120-277,60
90
72.7/74.8
LEDINTA0012V50FO, GEPS12-60U,
GE060/MV/V12T1-A
120-277,60
90
60.2/60.5
LEDINTA0024V28FO
120-277,60
90
56.6/59
LED Dimmer, Models 9137 108 30902
1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth
Edition, which would cover the component itself if submitted for Listing.
2. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C.
3. The unit is intended for installation inside an electrical enclosure.
4. This unit is provided with a Class 105(A) insulation system. The unit may be used within an electrical enclosure or raceway
without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED
power supplies.
5. The Xitanium Dimmer is only suitable for use in Class 2 circuits powered by Advance LED drivers with maximum input rating of
24Vdc, 4.1A, or 12VDC, 5A. Dimmer circuit is 0-10VDC.
6. This LED Dimmer Controller must be used with either a 100K Ohms Potentiometer or a standard 0-10 V DC dimmer switch.
129
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
7. For dry or damp location.
LED Light Strings, Light Strings Generation II, Series LSL may be followed by additional suffixes; 12NC - "Affinium LED Light
Strings" part numbers are as follows: 929000116403, 929000116503, 929000116623, 929000116703, 929000116803,
929000145903, 929000145103, 929000149103, 929000149003, 929000148803, 929000148903.
1. LED’s were evaluated for connection to a UL Recognized Component Sign Accessory - UYMR2, Class 2 12 VDC maximum
output.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2
circuit.
4. For use in dry, damp, or wet locations.
LED modules, Models LMS 1W, LMS 3W, LMS 4W, LMS 12 W.
1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component – Sign Accessory Class 2
power supply.
2. These components have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical
enclosure.
4. Components are suitable for use in dry, damp and wet locations.
LED Drivers, Models LEDHCNA0024V41FLO, DCHCNA0025V41FP, and LEDHCNA0024V41DLO.
1. The LED Driver has been evaluated to comply with Class 2 output criteria.
2. The LED Driver is only suitable for use in Dry and Damp Locations.
3. The LED driver should be used within the recognized electrical ratings.
4. The LED driver case must be grounded in the end-use application.
5. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 3 inches spacing to top of enclosure and mounted not closure than 1 in. end to end or 4 in. side to side from
adjacent LED power supplies.
6. The units were submitted and tested for a maximum manufacturer’s recommended Tc point described in the table below. If
adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side, a temperature test shall be conducted
in the end use product.
Max. Case @ Tc, Ambient, °C (Reference
Model No.
Input Voltage, Hz
°C
only)*
LEDHCNA0024V41FLO
347-480,60
85
52/53
DCHCNA000025V41FP
347-480,60
85
52/53
LEDHCNA0024V41DlO
347-480,60
85
57.8/58.2
7. The 0-10V dimming output for Model LEDHCNA0024V41DLO is part of the Class 2 secondary circuit.
LED drivers, Models XH075C105V070CNF1, XH150C105V140CNF1.
1. These products been evaluated for the following characteristics.
Model No.
Input type-
XH075C105V070CNF1,
XH150C105V140CNF1
Mains Input Constant Current, Output is Nonisolated
Output type
Product is rated
Ta, Rated
Dry & Damp
40°C
2. Rated output loading for these products was achieved using LED loads.
3. As part of temperature testing, the case temperature at the temperature reference point- identified as tc on the case- was
monitored. During the normal temperature test of the end product, the temperature at the temperature reference point is to be
monitored. The absolute value at the temperature reference point cannot exceed 80 °C.
4. These products are intended for building in. Acceptability of the LED driver- with respect to mounting, spacing, casualty,
temperature and segregation- is to be determined as part of the end device evaluation.
5. These products are dimmable using a low voltage 0-10 V proprietary interface. The interface circuit has been evaluated for
isolation from both primary (input) and secondary (output) circuits. The maximum output parameters of the 0-10 V interface met
the limitations for the Class 2 inherently limited per the UL 1310 standard.
6. The product shall be grounded in end product through its mounting ears.
7. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure. Otherwise, temperature test shall be conducted.
8. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise. Otherwise, temperature test shall be conducted.
PHILIPS SOLID-STATE LIGHTING SOLUTIONS INC
3 BURLINGTON WOODS DR
BURLINGTON, MA 01803
E312392
LED Data Enabler, Cat. Nos. Cat. No. 106-000003-06.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These devices are to be used in accordance with the ratings and load types as specified below.
Catalog Number
(Input-Output)
Operating Voltage
Input Current (A)
Type Load
106-000003-06
100 V-240 Vac
20 A
LED
3. These products may be provided with pigtail leads extending at least 150 mm (6 in) inside a wiring compartment or junction box.
The final installation should be evaluated in the end use application.
4. Spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 2 inches.
January 23, 2014
130
SIGN COMPONENTS MANUAL (SAM)
5. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches.
PLANAR SYSTEMS INC
1195 NW COMPTON DR
BEAVERTON, OR 97006
E312680
LCD Menu Boards, Models LC3250, LC4650.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are suitable for use in dry and damp locations.
3. These products shall be enclosed in the end product.
4. These products have the following electrical ratings:
Max Input
Voltage (V)
Model
Max Input Current
(A)
Frequency
(Hz)
LCD Menue Board Model LC3250
120
8.5
60
LCD Menue Board Model LC4650
120
13.5
60
5. These units were tested in open air room ambient temperature with the fans operating continuously. Therefore, these units shall
be subjected to a temperature test in the end product.
6. The need to conduct ground continuity tests shall be determined in the end product.
7. These products are intended for use in fixed signs for connection to a dedicated receptacle.
8. These EMI filter of these products were not subjected to Stored Energy Test.
LCD Menu Boards, Models LC3251, LC4651.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are suitable for use in dry and damp locations.
3. These products shall be enclosed in the end product.
4. These products have the following electrical ratings:
Model
Max Input
Max Input
Frequency
Power
Voltage (V)
Current (A)
(Hz)
(W)
LCD MENUE BOARD MODEL LC3251
120
5.0
60
580
LCD MENUE BOARD MODEL LC4751
120
9.5
60
1080
5. These units were tested in open air room ambient temperature with the fans operating continuously. Therefore, these units shall
be subjected to a temperature test in the end product.
6. The need to conduct ground continuity tests shall be determined in the end product.
7. These products are intended for use in fixed signs. The ultimate, supply connections shall be considered in the end product.
POLYBRITE INTERNATIONAL
1751 W DIEHL RD
SUITE 110
NAPERVILLE, IL 60563
E303143
LED Tubes, Cat. No. LEDT8C-3000K-2-120V, LEDT8C-4100K-2-120V, LEDT8C-5000K-2-120V, LEDT8F-3000K-2-120V,
LEDT8F-4100K-2-120V, LEDT8F-5000K-2-120V, LEDT8C-3000K-4-120V, LEDT8C-4100K-4-120V, LEDT8C-5000K-4-120V,
LEDT8F-3000K-4-120V, LEDT8F-4100K-4-120V, LEDT8F-5000K-4-120V, LEDT8C-3000K-5-120V, LEDT8C-4100K-5-120V,
LEDT8C-5000K-5-120V, LEDT8F-3000K-5-120V, LEDT8F-4100K-5-120V, LEDT8F-5000K-5-120V, LEDT8C-3000K-8-120V,
LEDT8C-4100K-8-120V, LEDT8C-5000K-8-120V, LEDT8F-3000K-8-120V, LEDT8F-4100K-8-120V, LEDT8F-5000K-8-120V,
LEDT8C-3000K-2-240V, LEDT8C-4100K-2-240V, LEDT8C-5000K-2-240V, LEDT8F-3000K-2-240V, LEDT8F-4100K-2-240V,
LEDT8F-5000K-2-240V, LEDT8C-3000K-4-240V, LEDT8C-4100K-4-240V, LEDT8C-5000K-4-240V, LEDT8F-3000K-4-240V,
LEDT8F-4100K-4-240V, LEDT8F-5000K-4-240V, LEDT8C-3000K-5-240V, LEDT8C-4100K-5-240V, LEDT8C-5000K-5-240V,
LEDT8F-3000K-5-240V, LEDT8F-4100K-5-240V, LEDT8F-5000K-5-240V, LEDT8C-3000K-8-240V, LEDT8C-4100K-8-240V,
LEDT8C-5000K-8-240V, LEDT8F-3000K-8-240V, LEDT8F-4100K-8-240V, LEDT8F-5000K-8-240V.
1. These products are suitable for use in dry, or damp locations.
2. The lamp is maintained not less than 2 inches (50.8 mm) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacing from lampholder to sign housing is zero.
3. This LED lamp is not for use with internally shunted bipin lampholders used with fluorescent instant start lamps.
POP DISPLAYS USA LLC
555 TUCKAHOE RD
YONKERS, NY 10710
E335345
Power Box with Class 2 Supply designated as "LED Power Box", Model 23369-420.
1. These products are suitable only for use in combination with portable type signs.
2. These products are suitable for use in dry location only.
3. The total maximum current for all three dedicated receptacle shall be marked max. 8 Amps.
5. These products are provided with the following electrical ratings:
Input
Model Designation
Vac
A
Hz
LED Power Box
120
8
60
6. These products are provided with maximum 3 dedicated receptacles.
7. These products are suitable for use in US only when provided with the Class 2 Power Supply Mean Well Enterprises Co Ltd
(E320521), model no. LPC-20-350.
131
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
PRINCIPAL LED
3503 ARDEN RD
SAN ANGELO, TX 76901
E341517
Class 2 LED Module, designated as PL-XX#-YYO-Z Series, where XX may be FS (Fusion), OP (Optima) or SP (The Spec); #
may be any number 0 to 9; YY may be any combination of letters AA to ZZ; O may be any number 0 to 9; and Z may be letter N or
P.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limits and is rated 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with Class 2 supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
LED Driver with Class 2 Output, Model PL-PS-60-12.
1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. This product is provided with the following electrical ratings:
Input
Output
Model
Vac
A
Hz
Vdc
A
PL-PS-60-12
100-240
1.2
50/60
12
5.0
3. The Class 2 output of this power supply is suitable for use in dry, damp and wet locations.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. This product shall be enclosed in the end product.
6. This product is suitable for factory wiring only.
Class 2 LED Modules, designated as PL-XX#-YYO-Z-WWWW Series where XX may be replaced with LT (Light Tape) or LE
(Light Edge); # may be replaced with any numeric character 0 to 9; YY may be replaced with any combination of alpha character
AA to ZZ; O may be replaced with any numeric character 0 to 9; Z may be replaced with letter N or P; and WWWW may be any
combination of alphanumeric characters.
1.These products are only intended for use and connection to a Class 2 power source rated 12 Volt DC or less.
2.When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3.These products are suitable for use in dry, damp and wet locations.
4.These products are not required to be enclosed or protected from the weather in the end product.
5.These products may be secured in place in the end product by any means available.
Class 2 output LED drivers, Model PL-MV-60-12.
1. LED driver has been evaluated using resistive load resulting in the electrical input and output noted below.
Model No.
PL-MV-60-12
Input
Voltage (V)
HZ
120-277
50/60
Output
Current (A) Power (W) Voltage (Vdc) Current (A)
0.65
77.5
12/14
5/4.3
2. LED driver is provided with Class 2 output.
3. LED driver is intended to be operated in a maximum ambient (Ta) noted as below:
Model
PL-MV-60-12
Ta (°C)
40
4. LED driver suitable for dry location only.
5. LED driver is provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a suitable
enclosure shall be considered in the end product.
6. LED driver is intended to be operated on a maximum 20 A branch circuit.
7. The need of the grounding means shall be determined in the end product.
8. LED driver shall be enclosed within a suitable end product enclosure.
9. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
10. In the end product, LED Driver shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
PRO-LITE INC
BLDG D
3505 CADILLAC AVE
COSTA MESA, CA 92626
E323060
LED Modules, Model "LED NUMURAL & TEXT DISPLAY MODULES", Model PL-DBPC-XXXXXX Series, where XXXXXX may be
any alphanumeric characters.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. These products are each rated max. 28 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry and damp locations with supply sources rated at 24 Volts DC or less.
5. These products may be secured in place in the end product by any means available.
6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
January 23, 2014
132
SIGN COMPONENTS MANUAL (SAM)
LED Arrays, Model PLxxxM-Lcy-Pzzzz-8D, where xxx and y may be any alphanumeric characters and zzzz may be 1, 2, 3 or 4.
1. These products are rated at 5 Vdc and 3.5 Amp per module.
2. These products are suitable for use in dry and damp locations.
3. The side opposite the LED lens portion of the LEDs shall be enclosed in the end product.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. The Mean Well Power Supplies, model SP-150-5 shall be provided with a Listed fuse rated max. 20 Amp, min 240 V on the
output circuit. The Mean Well Power Supplies, model SP-480-5 shall be provided with a Listed fuse rated max. 50 Amp, min 240
V on the output circuit.
6. Both the LED modules and the power supply shall be installed in a suitable electrical enclosure with an enclosure rated sign
face.
LED Arrays system, Model PL-DBPC-XXXXXXXX, where XXXXXXXX may be any alphanumeric characters.
1. The load side (LED modules) of these products are rated at 12 Vdc per module.
2. In the end product these products shall be subjected to Exclusion of Water test when used in outdoor applications.
3. The products shall be enclosed in the end product.
4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
5. These products should be installed in accordance with the manufacturer’s instructions.
Class 2 LED Modules, designated as "LED NUMERAL & TEXT DISPLAY MODULES", Model PL-YYYY-XXXXXX Series, where
YYYY and XXXXXX may be any alphanumeric characters
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 24 V DC.
3. These products are each rated max. 28 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry and damp locations with supply sources rated at 24 Volts DC or less.
5. These products may be secured in place in the end product by any means available.
6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
PROCESS RETAIL GROUP INC
5800 S MOORLAND RD
NEW BERLIN, WI 53151
E354869
LED Strip, designated Model LS, followed by PRG, followed by 01 through 99, followed by x, followed by 01 through 99, followed
by 1 or 2, followed by 01 through 99, followed by 1 or 2, followed by 1, 2 or 3.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
PWM GMBH & CO KG
KOLNER STR 120
51691 BERGNEUSTADT, GERMANY
E188273
Sign controller, Model “E-Box-XX” Series, where XX may be any number from 0 to 9 or any letter of alphabet from A to Z or
combination of numbers and letters.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These devices are to be used in accordance with the ratings and load types as specified below.
(Input-Output) Operating
Voltage (V)
Input
Output
Catalog Number
Max Output Current (rms)
Type Load
(AC)
(DC)
E-Box-45
100
15
4.75
LED
E-Box-45
120
15
1.95
LED
E-Box-45
240
15
3.83
LED
3. These components are not provided with suitable enclosure or sign body. The need for a electrical enclosure should be
considered in the end product.
4. Spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 2 inches.
5. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches.
6. The suitability of output wiring shall be suitable for use with Class 1 wiring system.
7. The output of these components exceeds Class 2 limits such that it is not acceptable for use with products designated on for use
when connected to a Class 2 circuit.
LED Modules, “LED Digits”, Model PSDU-XX-YYY, where XX may be replaced with any letters of alphabet from A to Z or with
numbers from 00 to 99 or combination of letters and numbers; YYY may also be replaced with any letters of alphabet from A to Z
or with numbers from 000 to 999 or combination of letters and numbers.
1. Wiring and means of connection between modules shall be investigated in the end product requirements.
133
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. No tests have been conducted on these components and as such, end product testing should be considered
3. These modules units are not provided with suitable enclosure or sign body. The need for a electrical enclosure should be
considered in the end product.
4. These components are to be installed in accordance with the manufacturer's instructions.
5. These Modules are acceptable for use on a Class 2 circuit and when powered by other than a Class 2 circuit, end product
requirements, such as enclosure and accessibility, should be applied.
Control Unit, Model CU-115V-XX, means that between 00 and 99 and will be increased by one, with every new software release.
1. Wiring and means of connection between modules shall be investigated in the end product requirements.
2. These devices are to be used in accordance with the ratings and Load types as specified by the ELECTRICAL RATINGS.
3. These components are to be installed in accordance with the manufacturer’s instructions.
4. Spacings within the low voltage circuits of the control board are not specified.
Electro Magnetic Power Unit Controller, Model E-BOX-EM-XX Series, where XX may be replaced with any letters of alphabet
from A to Z or with numbers from 00 to 99 or combination of letters and numbers; YYY may also be replaced with any letters of
alphabet from A to Z or with numbers from 000 to 999 or combination of letters and numbers.
1. Wiring and means of connection between modules shall be investigated in the end product requirements.
2. These devices are to be used in accordance with the ratings and Load types as specified at the ELECTRICAL RATINGS.
3. This product is for use in combination with Electro Magnetic Display Module 9-Segment fuel price displays, Model “EMDM-XXYYY” Series. When used in other combinations, considerations for testing of these components shall be considered in the end
product.
4. These modules are not provided with suitable enclosure or sign body. The need for an electrical enclosure should be considered
in the end product.
5. These components are to be installed in accordance with the manufacturer’s instructions.
6. Spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 2 inches.
7. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches.
8. Spacings within the low voltage circuits of the control board and segment control are not specified.
Electro Mechanic Display Module, Model EMDM-XX-YYY and Electro Magnetic Separate Module 9-Segment fuel price display
Model “EMSM-XX-YYY”, where XX may be replaced with any letters of alphabet from A to Z or with numbers from 00 to 99 or
combination of letters and numbers; YYY may also be replaced with any letters of alphabet from A to Z or with numbers from 000
to 999 or combination of letters and numbers for use in Electric Signs.
1. Wiring and means of connection between modules shall be investigated in the end product requirements.
2. These products are for use in combination with Sign controller, Model “E-BOX-EM-XX” Series of PWM GMBH & CO KG. When
used in other combinations, considerations for testing of these components shall be considered in the end product.
3. These modules are not provided with suitable enclosure or sign body. The need for an electrical enclosure shall be considered
in the end product.
4. These components are to be installed in accordance with the manufacturer’s instructions.
5. These products are only suitable for connection to a low voltage power source, rated 15 Volt DC or less and max. 2A, other than
a low voltage power source, end product requirements, such as enclosure, spacing and accessibility, should be applied.
6. Spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 2 inches.
7. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches.
LED digits, Model ILD-XXX-YY, LED Decimal Point model ILP-XXX-YY Suitable for Wet Location Use, Line Controller model LLSXX and Light Sensor model ISS-XX Suitable for Damp Location Use, where XXX may be replaced with any letters of alphabet from
A to Z or with numbers from 000 to 999 or combination of letters and numbers; YY may also be replaced with any letters of
alphabet from A to Z or with numbers from 00 to 99 or combination of letters and numbers for use in Electric Signs..
1. Only Input Test and Mold Stress Relief Distortion Tests at 70°C on the LED Digits and LED Decimal Point has been performed,
the need for additional tests shall be considered in the end product.
2. Wiring and means of connection between LED Digits or LED Decimal Point shall be investigated in the end product
requirements.
3. These devices are to be used in accordance with the ratings and load types as specified at the ELECTRICAL RATINGS.
4. These products were used as load with testing of PWM GMBH & CO KG, Sign controller, Model E-Box-XX Series. When used
in other combinations, considerations for testing of these components shall be considered in the end product.
5. The components are not provided with suitable enclosure or sign body. The need for an electrical enclosure shall be considered
in the end product.
6. These components are to be installed in accordance with the manufacturer’s instructions.
7. These products (LED Digits and LED Decimal Point) are suitable for use in Wet Locations Only and are acceptable for use on a
Class 2 circuit only, when powered by other than a Class 2 circuit, end product requirements, such as enclosure, spacing and
accessibility, should be applied.
8. The Line Controller and light Sensor are suitable for use in Dry and Damp Locations Only and are is acceptable for use on a
Class 2 circuit only.
9. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches
FAN Module, Model Fan Set-XX, where XX may also be replaced with any numbers from 00 to 99.
1. Input Test, Rain and Mold Stress Relief Distortion Tests at 70°C on the
FAN-SET-XX has been performed, the need for additional tests shall be considered in the end product.
2. These components should be installed in accordance with the manufacturer's instructions.
3. The device is to be used in accordance with the ratings and load types as specified at the ELECTRICAL RATINGS.
4. The Sign controller, Model E-Box-XX Series and Line Controller model "LLS-XX", manufactured by PWM GMBH & CO KG,
were used for testing the Fan assembly's models "FAN-SET-01, FAN-SET-02, and FAN-SET-03", when used in other
combinations, considerations for testing of these components shall be considered in the end product.
5. The Fan Cover (louver) openings shall always face down, if otherwise it needs to be provided with an "Up" marking and arrow
for mounting position that keeps water out.
January 23, 2014
134
SIGN COMPONENTS MANUAL (SAM)
6. The Rain Test per UL 879 was performed with the Fan assembly's models "FAN-SET-01, FAN-SET-02, and FAN-SET-03" in the
positions described in the manual instruction. Suitability for outdoor use when installed shall be considered by the end product
requirements.
7. The Fan assembly model "FAN-SET-01" can exhaust air and pull air, and shall be mounted as described in the manual
instruction.
8. The Fan assembly's models "FAN-SET-02 and FAN-SET-03" can only pull air, and shall be mounted as described in the manual
instruction.
9. The component is not provided with suitable enclosure or sign body. The need for an electrical enclosure shall be considered in
the end product.
10. Wiring and means of connection between modules shall be investigated in the end product requirements.
11. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches
12. This product is suitable for use in Damp Locations and is acceptable for use on a Class 2 circuit only, when powered by other
than a Class 2 circuit, end product requirements, such as enclosure, spacing and accessibility, should be applied.
LED Module, Backlight-XX-YYY, where XX stands for 04 LEDS or 08 LEDS or 12 LEDS or 16 LEDS YYY may also be replaced
with any letters of alphabet from A to Z or with numbers from 000 to 999 or combination of letters and numbers.
1. Only Input Test and Mold Stress Relief Distortion Tests at 70°C on the Backlight-XX-YYY has been performed, the need for
additional tests shall be considered in the end product.
2. Means of connection between modules shall be investigated in the end product requirements.
3. The device is to be used in accordance with the ratings and load types as specified at the ELECTRICAL RATINGS.
4. This product was used as load with testing of PWM GMBH & CO KG, Sign controller, Model E-Box-XX Series. When used in
other combinations, considerations for testing of these components shall be considered in the end product.
5. The component is not provided with suitable enclosure or sign body. The need for an electrical enclosure shall be considered in
the end product.
6. This component is to be installed in accordance with the manufacturer's instructions.
7. This product is suitable for use in Dry and Damp Locations and is acceptable for use on a Class 2 circuit only, when powered by
other than a Class 2 circuit, end product requirements, such as enclosure, spacing and accessibility, should be applied.
8. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of
enclosure is kept at minimum 6 inches
QUASAR LIGHT CO LTD
UNIT 1001 FOURSEAS BLDG
208-212 NATHAN RD
KOWLOON, HONG KONG
E464626
Class 2/LPS LED modules, Models QXXYY-ZZ series, where X, Y and Z can be combinations of any numbers and letters.
1. These products are only suitable for connection to a Class 2 or LPS power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 or LPS voltage and
energy limited circuits.
3. When these units are connected to a Class 2 or LPS supply circuit, they are not to draw a total wattage of greater than the
secondary or output rating of the Class 2 or LPS supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less..
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. The suitability of heatsinking for these LED modules shall be determined in the end product.
8. When these products are used in applications other than signs the need to conduct a temperature test shall be considered.
RAB LIGHTING INC
170 LUDLOW AVE
PO BOX 970
NORTHVALE, NJ 07647
E359881
Class 2 LED Power Supply, Cat. No. RD14-09-Annnn,RD14-10-Annnn and RD14-12-Annnn,RD14-13-Annnn, RD14-15-Annnn,
RD14-18-Annnn, RD14-22-Annnn, RD14-24-Annnn, RD14-36-Annnn, RD14-48-Annnn, where "A" represents constant current and
"nnnn" may be any alphanumeric characters that represent output current.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the
ultimate application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1,
300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application. 4. These
power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be
determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-0 for Models and the necessity of additional fire barriers shall be determined in end product.
7. The maximum temperature of the enclosure should not exceed 90°C.
Class 2 LED Power Supply, Cat. No. RD12-10-Annnn,RD12-12-Annnn,RD12-13-Annnn,RD12-15-Annnn ,RD12-17-Annnn,RD1218-Annnn,RD12-22-Annnn,RD12-24-Annnn,RD12-36-Annnn and, RD12-52-Annnn,where "A" represents constant current and
"nnnn" may be any alphanumeric characters that represent output current.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
135
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3.
4.
5.
6.
The suitability of the input and output connections shall be determined in each end use application.
These power units are intended for dry or damp location use only.
Strain Relief and Impact Tests have not been investigated.
The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. When conducting temperature test in the end product, the maximum temperature on the enclosure (case) shall not exceed
80°C. When provided with alternate enclosure material R/C (QMFZ2), Teijin Chemicals Ltd. (E50075), Material designation
LN-1250G, the maximum temperature on the enclosure (case) shall not exceed 90°C.
8. Class 2 Power Supply, Model RD12-52-Annnn are suitable for use in US only.
Class 2 LED Power Supply, Models RD117-12-Annnn, RD117-24-Annnn and RD117-36-Annnn, where "A" represents constant
current and "nnnn" may be any alphanumeric characters that represent output current.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4 When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These products with leads are suitable for use in commercial application only when marked with 277 V input voltage.
Class 2 LED Power Supply, Models RD125-12-Annnn, RD125-24-Annnn, RD125-36-Annnn,RD125-42-Annnn, RD125-50-Annnn,
Where "A" represents constant current and "nnnn" may be any alphanumeric characters that represent output current.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry and damp locations only.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
5. These lead connected products are suitable for use in commercial application only when marked with 277 V input voltage.
6. These units employ a Class 105 (A) insulation system on Transformer (T1).
Class 2 LED Power Supply, Model RD19-XX-YZ-E, where XX can be 19, 24 or 36; Y can be G or T; Z can be G or T; and E can
be any number from 170 to 999. ; which may be followed by suffix “DV”.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
Class 2 output requirements for dc circuits.
2. Models RD19-TT-E are suitable for use in dry and damp locations. Models RD19-GG-E are suitable for use in dry, damp and
wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end
product.
5. When not marked for “Dry and Damp Locations Only” the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be
provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
6. These products are suitable for use in commercial application only when marked with 277 V input voltage.
7. When provided with the alternate conduit caps on page 2A, the power supply shall be provided with an additional fire
enclosure.
8. Cord connected (not cord and plug) models are suitable only for use in cord connected signs:
A) The suitability of the cord length, type, and temperature rating shall be determined in the end use.
B) Strain relief testing has been conducted at 20 lbs. The need for additional strain relief shall be determined in the end use.
C) Leakage current testing has not been conducted on the cord connected models and shall be conducted in the end use.
9. Model RD19-XX-YZ-E-DV series are provided with a dimming option for use with a 0-10VDC dimming system.
RC GLOBAL INDUSTRIES INC
31208 CTY 71
EAGLE BEND, MN 56446
E334806
LED Single Tube, Models GF-028DC1-18, GF-030DC1-21, GF-030DC1-24; LED Double Tube, Models GF-015DC3-06, GF024DC3-09, GF-030DC3-12, GF-050DC3-15, GF-055DC3-18, GF-060DC3-21, GF-060DC3-24.
1. Lamps are for connection in parallel only and maintain polarity.
2. Only for use with the Rose City driver and lamp combinations specified below.
Lamp Voltage DC
Lamp Wattage
GF-028DC1-18
Lamp Model
37
28
SPS-A202806051
GF-030DC1-21
37
30
SPS-A203006051
GF-030DC1-24
37
30
SPS-A203006051
GF-015DC3-06
37
15
SPS-A203006051
GF-024DC3-09
37
24
SPS-A203006051
GF-030DC3-12
37
30
SPS-A203006051
GF-050DC3-15
37
50
SPS-A205006051
GF-055DC3-18
37
55
SPS-A205506051
GF-060DC3-21
37
60
SPS-A206006051
GF-060DC3-24
37
60
SPS-A206006051
3. For dry or damp location use only.
4. For use with R17d recessed double-contact lampholders only.
Lamp Driver
January 23, 2014
136
SIGN COMPONENTS MANUAL (SAM)
5. Lamps may be mounted vertically or horizontally.
6. Thermal clearance from lampholder to plastic or wood not required.
7. Minimum clearance from lamp to adjacent construction is 1/2in (12.7mm).
Constant current driver, Models SPS-A201506051, SPS-A202406051, SPS-A202806051, SPS-A203006051, SPS-A205006051,
SPS-A205506051, and SPS-A206006051.
1. LED driver is required to be installed in an electrical enclosure.
2. For dry or damp location use only.
3. The driver has been temperature tested in an ambient of 40C.
4. A temperature test is not required when the LED drivers are mounted not closer than 1 in. end to end or 4 inch side to side to
adjacent LED drivers or power supplies.
5. Driver shall be used with lamp that matches output ratings.
Model
Input Voltage DC
Wattage
Output Voltage VDC
Output Current A
SPS-A201506051
48
15
36-38
0.368
SPS-A202406051
48
24
36-38
0.576
SPS-A202806051
48
28
36-38
0.672
SPS-A203006051
48
30
36-38
0.73
SPS-A205006051
48
50
36-38
1.16
SPS-A205506051
48
55
36-38
1.35
SPS-A206006051
48
60
36-38
1.46
RELUME TECHNOLOGIES TM
33844 STERLING PONDS BLVD
STERLING HEIGHTS, MI 48312
E252627
Class 2 LED Module, Cat. No. Silver Circuit.
1. Portable LED signs may be used with Listed or R/C Class 2 power supplies, used in accordance with the conditions of
acceptability. Permanently wired LED signs are used with R/C (UYMR2) LED drivers used in accordance with their conditions
of acceptability. These products are only suitable for connection to a 24 volt maximum DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp locations. When the maximum output of the power supply is 24V continuous
dc or 12.4V peak for dc interrupted at a rate of 10 to 200Hz, the products may be installed in wet locations.
5. These products are not required to be enclosed or protected from weather.
6. These products are suitable to serve as part of the enclosure, with optional conduit knockout, in the end product sign.
Thickness of aluminum PWB
Max. length of enclosure (Straight line)
0.04”
48” or less
0.045” or greater
60” or less
RETOP LED DISPLAY CO LTD
D BLK, CHUANGJIAN 2ND PHASE
INDUSTRIAL PARK, YINGRENSHI COMMUNITY
SHIYAN ST, BAOAN DISTRICT
SHENZHEN, GUANGDONG 518108 CHINA
E362949
LED modules, designated as "RT-XXYYY" Series, where XX and YYY may alphanumeric characters to represent different sizes.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These products are suitable for use in dry locations.
3. These products shall be enclosed in a suitable electrical enclosure in the end product.
4. These products have the following electrical ratings:
Model
Max Input
Voltage (V)
Max Input
Current (A)
Max Input
Power (W)
Frequency (Hz)
“RT-XXYYY”
120
5
580
60
5. These units were tested in open air room ambient temperature with the fans operating continuously. Therefore, the need to
conduct temperature testing shall be determined in the end product.
6. The need to conduct ground continuity tests shall be determined in the end product.
RISHANG OPTOELECTRONICS CO LTD
2,3,4,5F BLK 2 HONGFA JIATELI
HI-TECH PARK SHIXIN COMMUNITY
SHIYAN TOWN BAO'AN DISTRICT SHENZHEN, GUANGDONG 518108 CHINA
E340368
Class 2 LED Modules, Cat. Nos. M133AA, M103AA, M113BA, M102B.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
137
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4. These products are suitable for use in dry, damp, and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Modules, Models M6XXXA and M6XXXB series; where The first X may be replace with 0~9, indicates product size
or shape; The second X may be replaced with 1~9, indicates product LED quantity; The third X may be replaced with A~Z or XB,
indicates product LED encapsulation types.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit,
they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. For M601C series, three units are consisted one module.
7. The suitability of supply leads shall be determined in end use.
Class 2 LED Modules, models Z6XXXXD and Z7XXXXD series; where the first X may be replaced with 0~9 or A~Z, indicates
product size or shape; the second and the third may be replace with 01~99 or when the second X may be replaced with A~Z, the
third X may be replaced with 1~9,these digits or letters indicate LED quantity; the fourth X may be replaced with A~Z or XB,
indicates LED encapsulation types.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
Class 2 LED Modules, models MXXXXXX, RXXXXXXX and ZXXXXXXX series. For MXXXXXX series, the first X may be
replaced with A~Z or blank; the second X may be replaced with 0, 1, 2, 3, 6, 8, 9 or A~G; the third X may be replace with 0~9 or
A~Z; the fourth X may be replaced with 1~9; the fifth X may be replaced with A~Z or XB; and the sixth X may be replaced with
A~E, M, N, Q or P. For RXXXXXXX series, the first X may be replaced with A~Z or blank; the second X may be replaced with 0, 1,
2, 3, 5, 6, 8, 9 or A~C; the third X may be replaced with 0~9 or A~Z; the fourth and the fifth X may be replace with 01~99, or when
the fourth X may be replaced with A~Z, the fifth X may be replaced with 0~9; the sixth X may be replaced with A~Z or XB; and the
seventh X may be replaced with A~E, M, N, Q or P. For ZXXXXXXX series, the first X may be replaced with A~Z or blank; the
second X may be replaced with 0, 1, 2, 3, 5, 6, 7, 8, D, E; the third X may be replaced with 0~9 or A~Z; the fourth and the fifth X
may be replace with 01~99, or when the fourth X may be replaced with A~Z, the fifth X may be replaced with 0~9; the sixth X may
be replaced with A~Z or XB; and the seventh X may be replaced with A~E, M, N, Q or P.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. The suitability of supply leads shall be determined in end use.
LED Drivers, Class 2, Models LW30-0120250, LW30-0240125.
1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
2. The products are intended to be built-in, the suitability of enclosure, mounting, input / output connections shall be considered in
the end product.
4. The products are intended for use in damp and wet locations.
5.These products are to be used in maximum ambient temperature (Ta) and Maximum case temperature (Tc) are as below :
Wet location
Damp location
Models
Ta
Tc
Ta
Tc
LW30-0120250
40
-70
85
LW30-0240125
40
-70
85
6. These LED drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does
not exceed the maximum output current.
7. These products are suitable for factory wiring only.
8. These products have been evaluated using a resistive load resulting in a maximum input and output.
9. The products are intended to be connected to a maximum 20 A branch circuit.
10. Humidity and Rain tests have been conducted for reference only. The need to repeat these tests shall be considered when
mounted in the end-product.
11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Drivers, isolated, non-class 2, Models LW60-0120500A, LW60-0240250A, LW100-0120833, LW100-0240416, LW1500121250, LW150-0240625.
1. These units have an isolated Non-Class 2 output.
2. The products are intended for built-in, the suitability of enclosure, mounting, input / output connections shall be considered in the
end product.
4. These products are suitable for use in damp and wet locations.
January 23, 2014
138
SIGN COMPONENTS MANUAL (SAM)
5. These products are to be used in maximum ambient temperature (Ta) and Maximum case temperature (Tc) are as below :
Wet location
Damp location
Models
Ta
Tc
Ta
Tc
LW60-0120500A
40
-70
85
LW60-0240250A
40
-70
85
LW100-0120833
40
-65
85
LW100-0240416
40
-65
85
LW150-0121250
40
-50
75
LW150-0240625
40
-50
75
6. The LED drivers are of the constant voltage type that requires the proper number of LED modules and controllers that does not
exceed the maximum output current.
7. These products are provided with Input and Output cord. The grounding continuity shall be checked in end product.
8. These products are suitable for factory wiring only.
9. The product has been evaluated as isolated output rated Non-Class 2 using a resistive load resulting in a maximum input and
output.
10. These products are intended to be connected to a maximum 20 A branch circuit.
11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
LED Drivers, isolated, Class 2, Models LW60-0120500, LW60-0240250, LW100-0120833A, LW100-0240416A.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Model Number
Input Voltage
(V)
Input Current
(A)
Frequency
(Hz)
Output
Voltage
(Vdc)
Output
Current
(mA)
LW60-0120500
100-240
0.78
50/60
12
5
LW60-0240250
100-240
0.78
50/60
24
2.5
LW100-0120833A
100-240
1.25
50/60
12
3.9 #
LW100-0240416A
100-240
1.25
50/60
24
4.0
# - Two outputs: Each 12 Vdc, 3.9 A.
3. In the end product the power supply spacing to other power supplies shall be at least 25.4 mm (1 in.) from end-to-end, and
101.6 mm (4 in.) from side-to-side. When spaced closer, a temperature test is required.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in dry, damp or wet locations.
7. The suitability of input/output leads and the wiring shall be determined in end product use.
8. These products are provided with 18 AWG stranded, rated minimum 300 Vac, minimum 60 C (for wet location), minimum 105 C
(for damp and dry location), for input and output connections. Acceptability of the leads relative to strain relief and secureness, is
to be determined as part of the end device evaluation. The grounding continuity shall be checked in end product
ROBERTSON WORLDWIDE
13611 THORNTON RD
BLUE ISLAND, IL 60406
E354509
Class 2 output LED drivers, Models LD060V012LRA, LD060V024LRA, LD080V024LRA, LD060V024LMA, LD060V024LMB,
LD060V024LMC, LD060V012LMA, LD060V012LMB, LD060V024LRB.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1.
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below:
Model
Ta (°C)
LD080V024LRA
40
LD060V012LRA
40
LD060V024LRA
40
LD060V024LMA
40
LD060V024LMB
40
LD060V024LMC
40
LD060V024LRB
52
LD060V012LMA
40
LD060V012LMB
40
4. These LED drivers are intended for use in dry and damp locations except that models LD060V012LMA and LD060V012LMB
are suitable for dry location only.
5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a
suitable enclosure shall be considered in the end product.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. The need of the grounding means shall be determined in the end product.
8. These LED drivers shall be enclosed within a suitable end product enclosure.
139
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
9. For model LD060V024LMC, the conduit knockout test was not conducted. The suitability is to be determined in end product.
10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
11. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
ROCOX INC
14001 TANGLE AIRE PL
AMARILLO, TX 79118
E73588
Sign Flasher, Models 110, 210, 310, 410, 120, 220, 320 or 420.
1. These are open-type devices. A suitable enclosure shall be provided in the end use and the suitability of the bonding means
through the mounting means shall be determined in the end use. The suitability of conduit connections shall be determined in
the end use.
2. These components are suitable for use in Dry or Damp Locations.
ROSTI INTEGRATED MANUFACTURING SOLUTIONS (SUZHOU) CO LTD
1 HUAZHENG ST
SUZHOU INDUSTRIAL PARK
SUZHOU, JIANGSU 215026 CHINA
E347776
Class 2 LED light board, Model. No. KLB355W.
1. This product is only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limited circuit and which is rated greater than 24 V DC.
3. When unit is connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of
the Class 2 supply.
4. This product is suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. This product is not required to be enclosed or protected from the weather in the end product.
6. When this product is used in applications other than signs the need to conduct a temperature test shall be considered.
7. This product cannot be wired in series.
S & F SUPPLIES INC
93 EMERSON PL
PO BOX 050071
BROOKLYN, NY 11205
E344915
LED Module, Models DLL4, DLL3, DLM3, DLM2, DLS2, DLN1.
1. These products have been evaluated for connection to a Class 2 power source only, rated 12 Vdc, 60 W max.
2. These products are suitable for use in dry, damp or wet locations.
3. The LED module is provided with leads for interconnection. The suitability of the leads shall be determined in the end product.
SABIC INNOVATIVE PLASTICS US LLC
SPECIALTY COMPONENTS & PRODUCTS
1 PLASTICS AVE
PITTSFIELD, MA 01201
E136722
Rigid sign face system, designated: Lexan S-10, SG, SL6832, SGC, 903, and Sabic Lexan Sign Grade Sheet All may be
followed by additional letters and/or numbers.
1. Acceptable for use in dry, damp and wet locations.
2. Acceptable for enclosure, sign body and decorative applications. For enclosure applications, exposed live parts shall be spaced
min. 0.8mm (1/32”) from the enclosure surface.
3. Suitable for use in component support applications.
4. Water exclusion must be determined in the end product.
5. This material is suitable for contact with heat producing components such as electrodes, transformers, power supplies and
ballasts in the end product.
6. Marking required on end product stating, "Replace only with (manufacturer's name of component), type (type designation of sign
face) sign face material".
7. Suitable for use in terminating conduit.
8. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed
to the interior of the sign. This may be accomplished with channels, flanges or other suitable mechanical means.
9. Not suitable for the support of components weighing more than 7.5lbs (3.4Kg).
SEOUL SEMICONDUCTOR
1B-25, 727-5 WONSI-DONG
DANWON-GU
ANSAN-CITY, KYUNGGI-DO 425-851 REPUBLIC OF KOREA
E363669
Class 2 LED modules, Model Nos. LED P541-CLA, LED P551-SEL, 1SCABIM-50, 1SCABIM-65, 1SCABIM-71, 3SCABIM-50,
3SCABIM-65, 3SCABIM-71.
1. These products are only suitable for connection to a Class 2 power source rated 14 V DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated at 14 V DC or less.
January 23, 2014
140
SIGN COMPONENTS MANUAL (SAM)
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 14 V DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
SHANGHAI HUILI TUVGAL SHEETS CO LTD
268 EAST KANGQIAO RD
PUDONG, SHANGHAI 201319 CHINA
E363988
Rigid non-enclosure rated sign faces, designated "PC face, PC edge".
1. These products are only suitable for use with Class 2 powered LED illuminated type signs.
2. These products are suitable for use in dry and damp locations only.
3. These products are limited to use with decorative, sign face, and sign
body applications only.
4. The rigid sign face non-enclosure rated material is not suitable for use as an electrical enclosure of non-Class 2 circuitry.
5. The sign face material shall be spaced a minimum of 5 cm (2 in.) from heat producing components.
6. Not intended for mechanical support of components.
SHANGHAI JIATANG ELECTRONIC CO LTD
NO 685 E GAOKE RD
HEQING TOWN
PUDONG
201201 SHANGHAI, CHINA
E242985
Channel letter LED Modules, Models SLS-1-X, SLS-2-X, SLS-3-X, and SLS-3-X-y (where, X may be replaced with any letters of
alphabet A~Z, or any number 0~9; y can be any letters of alphabet A~Z).
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component – Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12 V DC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited
to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. The following identifies the rating
to be used in calculating the maximum number of units per circuit.
Load Max
Cat. No.
(mAmps)
Watts
SLS-1-X
30
0.36
SLS-2-X
30
0.36
SLS-3-X, SLS 3-X-y
50
0.60
4. These products are suitable for use in dry, damp and wet locations.
5. The weather enclosure does not require evaluation.
Channel letter LED Modules, Models SU-3-X and SU-4-X, where X may be replaced with any letters of alphabet A through Z or
any numbers 0 through 9.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. Class 2 LED Illumination Module, model no. SU-3-X is each rated max. 1.5 Watts per unit. SU-4-X is each rated max. 1.2 Watts
per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or
output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
SHANGHAI WHQ OPTOELECTRONIC CO LTD
6788 BEI QING RD
200011 SHANGHAI, CHINA
E343895
Class 2 LED Module, Cat. No. WHQ-B100x, WHQ-B111x, WHQ-B160x, WHQ-B200x, WHQ-B211x and WHQ-B300x, where x
may be any alphanumeric character or blank.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less for models WHQ-B111x,
WHQ-B160x, WHQ-B200x, WHQ-B211x and WHQ-B300x and 24 Volt DC or less for model WHQ-B100x.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
3. These Class 2 LED modules are each rated as noted in the electrical ratings tables. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
SHEAD ENTERPRISES INC
15164 N 140 DRIVE
APT. 2187
E360000
141
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
SURPRISE, AZ 85379
Power supplies, Class 2, Models PLN-60-12, PLNF-60-12.
1. These LED Drivers comply with Class 2 output requirements.
2. These products are provided with the following electrical ratings:
Input Voltage
Input Freq
Input Current
Output Voltage
Output Current
Model No.
(VAC)
(HZ)
(A)
(Max. Vdc)
(Max. A)
PLN-60-12
100-277
50/60
1.3
12
5
PLNF-60-12
100-277
50/60
1.3
12
5
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end,
and 101.6 mm (4 in.) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products are intended for use in dry or damp locations only.
7. The suitability of input/output leads and the wiring shall be determined in end product.
8. These products are constant voltage type that require the proper number of LED modules and controllers that do not exceed the
maximum total output current rating.
9. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
Molded Silicone Rubber Boot/Nut Assembly, Model S.E.I. S-B-1000.
1. The suitability of protective barrier shall be determined in the end-use application.
2. Consideration shall be given to conducting a Water Exclusion Test in the end product.
3. The suitability of a Listed toggle switch for use with this boot shall consider the following:
(A) The toggle (switch actuator) shall be metal, and
(B) The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot.
(C) The assembly shall be mounted on the bottom or side surface of a sign body only.
SHENZHEN BRIGHT LIGHTING TECHNOLOGY CO LTD
BLDG 18 SHANGCHENG INDUSTRIAL PARK
SHIYAN TOWN
BAOAN DISTRICT
SHENZHEN, GUANGDONG 518108 CHINA
E352755
Class 2 LED Strip, Models BRT-12V-XXX[#], BRTWL-12V-XXX[#], BRT-HO-24V-XXX[#], BRTWL-HO-24V-XXX[#], BRT-VHO24V-XXX[#], BRTWL-VHO-24V-XXX[#].
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products do not require an electrical enclosure.
5. These products may be secured in place in the end product by any means available.
SHENZHEN COLLESUN LIGHTING CO LTD
ROOM 508 TOWER B
TIAN AN CYBER TIMES
FU TIAN DISTRICT
SHENZHEN, GUANGDONG 518040 CHINA
E356842
Sign accessories, LED sign box, Models PBS-8G, PBS-8R, PBS-12G, PBS-12R.
1. Enclosure is required and suitability should be considered in end products.
2. These products are suitable for Dry locations only.
3. These products are provided without mounting means. Mounting shall be determined in the end-use application.
4. Wiring should be considered by end products.
Sign accessories, gas price display modules, Models PBS-6G, PBS-6R, PBS-16G, PBS-16R, PBS-18G, PBS-18R, PBS-24G,
PBS-24R.
1. These components are intended to be mounted with sign and shall be reliably mounted with the end-product.
2. These products are suitable for use in Damp location. If used in wet location, additional investigation should be conducted.
3. Enclosure is required and suitability should be considered in end products.
4. For power supply cord, if not provided, wiring and strain relief means should be considered by end products.
SHENZHEN LINGBENYANG TECHNICAL CO LTD
A XINGYONGFENG INDUSTRIAL AREA
YINGRENSHI VILLAGE
BAOAN DISTRICT, SHIYAN TOWN
SHENZHENG, GUANGDONG 518000 CHINA
E348340
Class 2 LED Module, Models CH452F, CH743F, CK743F, TH384F, TH383F, TH502F, TK504F, ZH362F, ZH334F, ZH623F, LBYCH452F-5W-0001, LBY-CH743F-3W-0001, LBY-CK743F-3C-0001, LBY-ZH362F-5W-0001, LBY-ZH334F-7W-0001, LBYCK262G-3C-0001.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less for all models.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than electrical ratings.
January 23, 2014
142
SIGN COMPONENTS MANUAL (SAM)
3. These Class 2 LED modules are each rated as noted in the electrical ratings tables. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These LED modules have been evaluated electrical input noted below.
Alternate Model
Model
Voltage Rated wattage
Vdc
W
CH452F
LBY-CH452F-5W-0001
12
CH743F
LBY-CH743F-3W-0001
12
0.42
0.6
CK743F
LBY-CK743F-3C-0001
12
0.3
TH384F
-
12
0.8
TH383F
-
12
0.6
TH502F
-
12
0.42
TK504F
-
12
0.6
ZH362F
LBY-ZH362F-5W-0001
12
0.4
ZH334F
LBY-ZH334F-7W-0001
12
1.2
ZH623F
LBY-CK262G-3C-0001
12
0.6
SHENZHEN SUNCEN HI-TECH CO LTD
3RD FL, XINAOLIN MANSION
LANGSHAN ERLU NORTH DISTRICT
HI-TECH PARK NANSHAN
SHENZHEN, GUANGDONG 518057 CHINA
E348360
Sign Accessory, Model LED-P20-2R1G1B.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These devices are to be used in accordance with the ratings and load types as specified below.
Max. Operating Voltage, Current and Power
Input Power
Input (V)
Input Current (A)
(Watts)
Catalog Number
Type Load
LED-P20-2R1G1B
100-240VAC
3.5
350-840W
LED
3. The suitability of supply connections shall be considered in the end product.
4. The Rain Test was conducted on the front screen only. However, in an end product application where many panels are connected
together, the Exclusion of Water Test of whole product should be conducted.
5. Acceptability for multiple connections (daisy chaining) not exceeding 12 A (based on 14 AWG power supply cord) on a single
branch circuit shall be determined by the end product requirements.
6. The power supply cord is SJTOW type, 14 AWG, the suitability should be determined by end product.
7. Disconnect means and its suitability should be determined by end product.
8. Suitability of mounting means should be considered by end products.
SICOM SYSTEMS
4434 PROGRESS MEADOW DR
DOYLESTOWN, PA 18902
E336738
Sign Accessory, Model 1900-OC OCU.
1. These products are required to be enclosed in the end use sign. The diffuser over LCD screen shall be a R/C sign accessory,
rigid sign face, meeting electrical enclosure requirements for outdoor signs.
2. These products are intended only for factory installation in new signs.
3. Suitability for other than dry and damp locations shall be determined in the end used application.
4. Grounding of frame to supply ground is required. Suitability of bonding for grounding connection is to be determined in final
application.
5. Suitability of OCU mounting shall be determined in final application.
6. In the end product, the OCU spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
7. Suitability of the electrical connection to the final signage shall be determined in the end-use product.
8. Since the fan connection is located outside the OCU enclosure, the fans are required to be enclosed in the sign electrical
enclosure.
9. Installation Instructions shall be provided with each unit.
10. Fans that are identified for connection to Class 2 circuits only, may be connected to fan outputs provided the fans are installed
within sign electrical enclosure. The fan output circuits have been evaluated as LVLE (Low Voltage Limited Energy).
SIGN CRAFTERS INC
1508 STRINGTOWN RD
EVANSVILLE, IN 47711
Sign Accessory, Model LED PETALS
1. This component shall be installed in accordance with the manufacturer's installation instructions.
2. These products are suitable for use in dry, damp and wet location.
3. These products are rated as the following:
E341775
143
SIGN COMPONENTS MANUAL (SAM)
Model Designation
Input Voltage (Vac)
Input Current (A)
Input Frequency (Hz)
120
1.2
50/60
Led Petals
January 23, 2014
4. These units have not been tested for use in recessed or enclosed areas.
SIGN LED CORP, DBA LED EXPRESS
1438 SANTA ANITA AVE
STERLING HEIGHTS, MI 48312
SOUTH EL MONTE, CA 91733-1922
E338973
Class 2 LED Module Cat. No. LED Modules.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
SIGN SPECIALTIES INC
120 15TH ST NE
WATERTOWN, SD 57201
E319828
Sign Face Tensioning Systems, designated Flexi-Wedge Models FWC-15-Z, FWC-25-Z, FWC-15-SS, FWC-25-SS.
1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent
entrance of water in outdoor sign applications shall be determined in the end product.
2. This product has not be evaluated for use as an electrical enclosure.
3. Tensioning clips shall be spaced as described in the Installation Instructions.
4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent
billowing.
5. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face
requirements of UL 48 particularly clearance to lamps and lampholders.
6. These clips have been determined to be suitable with any R/C Flexible Sign Face Material of min. 0.020 inches (0.51mm)
thick, suitability for use with a material of lesser thickness shall be determined in the end product.
SIGN/LITE INC
319 GRANDVIEW
DRKODAK, TN 37764
E163602
Channel letter and small sign lighting systems, Models BLH-579-1-6*, BLV-579-1-6*, BLE-579-1-6*, BLH-13-1-6*, BLV-13-1-6*,
BLE-13-1-6*, BLH-846-1-6*, BLH-846-1-6-K*, BLV-846-1-6*, BLV-846-1-6K*. (*Outdoor signs and channel letters).
1. The exposed leads must be enclosed by a suitable means or be behind UYMR2, rigid sign face material.
2. Spacings of not less than 1/2 in. are to be maintained between the lampholder, live metal, or other parts that may be a source
of heat or arcing, and decorative and structural parts other than glass.
3. The ballast is to be within an overall electrical enclosure.
4. The ballasts shall be located not less than 1 in. apart when arranged end-to-end, and not less than 4 in. apart when arranged
otherwise.
SIGNALEX INC
5617 MCADAM RD
MISSISSAUGA, ON L4Z 1N4 CANADA
E86197
LED class 2 backlit panel, Model Luminex3.
1. These products are only intended for use with a LPS/Class 2 output power sources with 12 Vdc, maximum 5 A output.
2. When products provided with more than one input connector, there shall be no interconnection of the circuits allowed, and each
LPS/Class 2 circuit is separately connected to each LPS/Class 2 power supply. Each input shall not exceed 5 A. Power supply
with multiple Class 2 outputs may be used.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated Class 2.
4. These LED Backlight panels may be provided with a mounting means and frame. The suitability is to be determined in the end
product.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED class 2 led strips, Model CarpetLight.
1. These products are only intended for use with a LPS/Class 2 output power sources with 24 Vdc, Maximum 4.1 A output.
2. When units are connected to a LPS/Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the LPS/Class 2 supply.
3. These products are suitable for use in dry and damp locations with supply sources rated Class 2.
4. These LED strips may be provided with a mounting means. The suitability is to be determined in the end product use.
SIGNCOMP
3032 WALKER RIDGE NW
GRAND RAPIDS, MI 49544
E136850
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
144
Flexible Sign Face Tensioning System and Sign Frames, Model FH, for use as a frameless design, Models FC, 5365, for use
with Frames Models RF, R3F, Model 24-63-390, for use with Frames Models 24-63-300, 24-63-305, 24-63-310, 24-63-315, and
Model 5360, for use with Frames Models 2090, 2142, 2094, 2105, 2104, 2085, 2065, 2112, 2092.
1. The following table details the acceptable clip/frame combinations:
Clip
Frame
FC, 5365
(frameless design)
FH
RF, R3F
24-63-390
24-63-300, 24-63-305, 24-63-310, 24-63-315
5360
2090, 2142, 2094, 2105, 2104, 2085, 2065, 2112, 2092
2. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent
entrance of water in outdoor sign applications shall be determined in the end product.
3. This product has not be evaluated for use as an ultimate enclosure.
4. Tensioning clips shall be spaced in the end product as described in the Installation Instructions.
5. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent
billowing.
6. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face
requirements of UL 48 particularly clearance to lamps and lampholders.
7. These clips have been determined to be suitable with any R/C Flexible Sign Face Material al least 0.020” (0.51mm) thick.
Suitability for use with a material of lesser thickness shall be determined in the end product.
Flexible Sign Face Tensioning System and Sign Frames designated Clip Tensioning System (CTS)
1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent
entrance of water in outdoor sign applications shall be determined in the end product.
2. This product has not be evaluated for use as an ultimate enclosure.
3. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent
billowing.
4. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face
requirements of UL 48 particularly clearance to lamps and lampholders.
5. These clips have been determined to be suitable with any R/C Flexible Sign Face Material at least 0.02in. (0.53mm) thick.
Suitability for use with a material of lesser thickness shall be determined in the end product.
6. This product is suitable for use in Dry, Damp, and Wet Locations.
7. Clips shall be spaced no more than 8 in apart and no closer than 6 in apart in accordance with the installation instructions.
Raceway, Cat. Nos. B8789, B8788, ZipWayBR2012, End Cap.
1. The mounting means of a channel letter or sign component to the raceway was not evaluated. Acceptability of securement shall
be determined in the end use.
2. An outdoor sign may require a water exclusion test.
3. Suitable for indoor and outdoor use, drain holes are required for outdoor use.
4. Mounting means of the back plate was not evaluated.
5. Entrance of GTO into the raceway was not evaluated. Protection of the wiring shall be determined in the end use.
6. Product has been evaluated for use with LED or neon channel letter signs.
Notching tools, used for sign face retention system for channel letters, Models JTCP-BB2011, JTK-BB2011.
1. The retention of the sign face and the channel letter was not evaluated. Acceptability of securement shall be determined in the
end use.
2. An outdoor sign may require a water exclusion test.
3. This tool forms tabs that are approximately 3/8 inch wide by 3/16 inch long and extend outward about 1/8 inch.
4. Best results are obtained when the sign face with plus tolerance of 1/8 inch over hang along the contour of the channel letters or
shapes to achieve a snug-fit joining of the two component.
5. Bottle opener type tool (Key), Model JTK-BB2011 is provided for the removal of the plastic sign face from the metallic channel
letter.
6. The tooling shall be serviced and maintained in accordance with the manufacturer's instructions. A service log shall be
maintained for each machine.
Retention clips, Models ZipClip1/8, ZipClip3/16.
1. The retention of the sign face and the channel letter was not evaluated. Acceptability of securement shall be determined in the
end use.
2. These retention clips are approximately 0.438 inch wide by 0.5630 inch or 0.625 inch long.
3. Best results are obtained when the sign face with plus tolerance of 1/8 inch over hang along the contour of the channel letters or
shapes to achieve a snug-fit joining of the two component.
4. Bottle opener type tool (Key), Model JTK-BB2011 is provided for the removal of the plastic sign face from the metallic channel
letter.
5. Sign face is adhesive secured to the trim-cap. Only size trim cap is used, but the retention clip varies with thickness of the sign
face.
Sign face with thickness of 1/8 inch shall use 9/16 inch length retention clips, Model ZipClip1/8. While sign face with 3/16 inch
shall use 5/8 inch length, Model ZipClip3/16.
SIGNTRONIX
E364872
1445 W SEPULVEDA BLVD
TORRANCE, CA 90501
LED gas price display modules, Models GURU-GPU-8, GURU-GPU-12, GURU-GPU-16, GURU-GPU-18, GURU-GPU-24,
GURU-GPU-30.
1. These components are intended to be installed in a sign and shall be reliably mounted in the end product.
145
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
2. Suitable for connection to a branch circuit not exceeding 20A.
3. If installed in an outdoor sign, the Water Exclusion Test should be conducted on the overall end-product.
4. Any changes or additional components added by the end-product sign manufacturer require consideration of additional testing
(Temperature, Input, etc.).
SILICON CONSTELLATIONS INC
2980 SCOTT BLVD
SANTA CLARA, CA 95054
E324890
LED Modules, Model No. REELLIOUS I.
1. These products are only suitable for connection to a Class 2 power source rated 30 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 30 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means
available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
SINO-OPTO USA LLC, DBA LED LIGHTING SERVICES LLC
3575 COMMERCIAL AVE
NORTHBROOK, IL 60062
E342085
LED Tube, Cat. Nos. LLIT8-48-18W, LLIT8-24-10W.
1. These products are suitable for use in dry, or damp locations.
2. The lamp is maintained not less than 2 inches (50.8 mm) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacing from lampholder to sign housing is zero.
3. This LED lamp is not for use with internally shunted bipin lampholders used with fluorescent instant start lamps.
SINO-OPTO USA LLC, DBA LED LIGHTING SERVICES LLC
3575 COMMERCIAL AVE
NORTHBROOK, IL 60062
E345360
LED Tube, Cat. No. SN-T.
1. These products are suitable for use in dry, or damp locations.
2. The lamp is maintained not less than 2 inches (50.8 mm) from combustible materials such as wood or plastic and parts that are
a source of heat or arcing. Spacing from lampholder to sign housing is zero.
3. This LED lamp is not for use with internally shunted bipin lampholders used with fluorescent instant start lamps.
LED Tube, Cat. No. LLI-T10DBL.
1. Manufacturer's name, trade name, or trademark.
2. Distinctive catalog or model number.
3. The electrical ratings.
4. When multiple manufactures are involved, then a Factory ID identifying the product to a particular factory shall be provided.
5. Optional - “For Connection with Class 2 Circuits Only.”
SLOANLED, DIV OF SLOAN CO INC
5725 OLIVAS PARK DR
VENTURA, CA 93003
E215393
LED Modules, Cat. Nos. 701261, 701261-PW, 701340, with suffix -R, -O, -Y, -B, -G, -W or -A; Cat. Nos. 701340-PW with suffix R, -O, -Y, -A, -B, -G or -W; Cat. No. 701340-CM.
1.These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 V dc power source for Model 701340
and 7.5 V dc or 5 V dc power source for Model 701261.
2.These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3.The total number of Model 701261 LED Lighting Units are not to exceed a total of 75 units per Class 2 circuit. The total number
of Model 701340 LED Lighting Units are not to exceed a total of 40 units per Class 2 circuit.
4.These products are suitable for use in dry, damp and wet locations.
5.These products are not required to be enclosed or protected from weather.
Class 2 LEDs, “ThinLED”, Model 701228 , with suffix -A, -B, -G, -R, -W or -Y; Cat. No. 701228-18, with suffix -A, -B, -G, -R, -W or -Y.
1.
These products are only suitable for connection to a UL Listed or Recognized Class 2, max. 12 V dc power source. . Only
Models 701228-A, -R, or -Y are only suitable for connection to UL Listed or Recognized Class 2, max. 7.5 V dc.
2.
These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3.
The total number of these products when interconnected is not to exceed a total of 14 feet or 14 “ThinLED” units per Class 2
circuit. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4.
These products are suitable for use in dry, damp and wet locations.
5.
These products are not required to be enclosed or protected from weather.
Class 2 power supply, Model LED Outline Lighting Systems “FlexiBRIGHT”, Cat. No. 701499-X-Y, where X and Y may be any
alphanumeric character.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source or less.
January 23, 2014
2.
SIGN COMPONENTS MANUAL (SAM)
146
These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class
2 circuit.
4.
These products are provided with wire soldered on the printed wiring board for connection.
5.
These products are suitable for use in dry, damp and wet locations.
Class 2 LEDs, Modules designated, "LED STRIPE2 (Border Light)" and “701956-XXXXXX” series, where XXXXXX may be
replaced with alphanumeric characters.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. Class 2 LEDs, “LED STRIPE2 (Border Light)”, is rated max. 48 Watts per module. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
Class 2 LED Module, Cat. No. 701269-xxxxxxxxxx-MB Series, where xxxxxxxxxx may be blank or any alphanumeric characters.
1. These products have been evaluated only for use when connected to the Class 2 output of a Listed or Recognized power
source rated 15 V DC or less.
2. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V DC or less.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in the end product with any available means.
5. These products are rated for a maximum of 7.5 watts or less per module.
Class 2 LED Border Light, Class 2 "Border Light", Cat. No. 701189-XXXXXXXXXX series.
1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 30 V DC.
3. These products are each rated max. 100 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations when rated maximum 30 VDC.
5. These products are not required to be enclosed or protected from the weather in the end product when rated 30 VDC or less.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
LED Strips, Cat. No. 701174, 701181 and 701195 with suffix -R, -Y, -A, -B, -W, or -G followed by -1" through -24".
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 volt AC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limited supplies.
3. These products may be cut into segments through a black mark provided on the printed wiring board. No other cut across the
board is permitted.
4. Cat. No. 701174 is rated for 4.2 watts per foot, Cat. No. 701181 is rated for 9.2 watts per foot and Cat. No. 701195 is rated at
1.5 Watts per foot. The total number of feet of each type and inches for the inch unit are not to produce a total wattage of
greater than 60 watts per Class 2 circuit.
5. These products are suitable for use in dry, damp and wet locations.
6. These products are not required to be enclosed or protected from weather.
Class 2 LED Module, Cat. No. 701946-XXYYYYYYZZZ series, where XX, YYYYYY and ZZZ may be replaced with any
alphanumeric characters or blank.
1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source rated 24 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 power supply, Model 701285.
1. Power supply is intended to power LEDs in signs.
2. Power supply model is intended for permanent connection only.
3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed
inside a sign that complies with the Exclusion of Water Test in UL 48.
4. If the power supply output wiring is extended longer than the 5 foot leads provided, the spliced connections shall be made
inside a Listed junction box suitable for the application included with proper grounding.
Class 2 power supply, Cat. Nos. 701349, 701351.
1. Power supply models 701349 and 701351 are intended to power LEDs in signs.
2. Power supply model 701349 and 701351 are intended for permanent connection only.
3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed
inside a sign that complies with the Exclusion of Water Test in UL 48.
5. These power supplies have two outputs. The Class 2 output circuits are not to be conductively connected to each other in the
sign by wiring or other type of component.
6. The maximum rated output power for Model 701349 is 42 watts at each Class 2 output. The maximum rated output power for
Model 701351 is 60 watts at each Class 2 output.
Class 2 power supplies, Models 701507-MOD, 701507-MOD277 (AD060S277/347-SLN). All may be followed by alphanumeric
suffix.
1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class
2 output requirements for dc circuits.
2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
147
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on primary
circuit.
5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product.
6. When not marked for Dry and Damp Locations Only the power supply primary bracket shall be provided with min. 3.5 threads
and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3. 5 threads, the liquid tight shall be
provided with watertight fitting Listed (QCRV) 1/2 inch, liquid tight conduit fittings.
7. The suitability of grounding connection shall be determined in the end-use product.
Class 2 power supply, Model 701680.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief on input lead construction and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
7. Multiple power supplies shall be spaced at least 25mm (1 in.) end to end or 102mm (4 in.) in other directions. If lesser spacings
are used, then the Temperature Test shall be conducted in the end use product. For reference the maximum enclosure (case)
temperature on the power supply was 90°C when tested at 58.4° ambient.
Class 2 power supply, Model 701680-MW.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
4. These products are provided with the following electrical ratings:
Input
Model
701680-MW
Output
Vac
A
Hz
Vdc
A
100-240
0.55
50/60
12
1.67
5. These products shall be enclosed in the end product.
6. These power supplies are suitable for use in dry and damp locations.
Class 2 power supply, Model 701681.
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1,
300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated on input lead construction. The suitability of the enclosure as ultimate
enclosure shall be determined in the end-use application.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of the polymeric enclosure
is V-0 and the necessity of additional fire barriers shall be determined in end product.
7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 power supplies, Model 701495.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of four Class 2
outputs.
2. These power supplies are only suitable for use in dry, damp and wet locations.
3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
Class 2 power LED Lighting Strip, 701912-QQXXYYZZZ series, where QQ represents length, XX represents the LED color
temperature, YY represents configuration and ZZZ represents the LED drive current.
1. These products are only suitable for connection to a Class 2 power source, rated 24VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 24VDC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 "Dimming Control Knob" potentiometer, Model 701843.
1. These products are only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated max 12
VDC.
2. These products are suitable for use in dry and damp locations.
3. These products are suitable for factory wiring only.
4. These products are 1 Kohm potentiometers intended for connection to max 12 VDC Class 2 power supply that drops the voltage
to a 0-10 V signal to feed into the PWM dimmer.
Class 2 LED Modules, Cat. No. 701960-XXYYYZ Series, where XX, YYY, and Z may be replaced with any alphanumeric
character or blank.
1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source rated 24 Volt
DC or less.
January 23, 2014
148
SIGN COMPONENTS MANUAL (SAM)
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Component sign accessories, Class 2 power supply, Model 701507-60W1-CT.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Model Number
701507-60W1-CT
Input Voltage
Input
(V)
Current (A)
100-240
0.85
Frequency
(Hz)
Output Voltage
(Vdc)
Output Current
(A)
50/60
12
0-5
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and shall be spaced by standard j-box knockout spacing from side to side.
4. For field wiring, when Junction Box is not provided on the primary circuit, each unit shall be provided with detailed Installation
Instructions requiring the installer to use a UL Listed Junction box suitable for use in wet location for primary leads connection.
5. These products are intended for use in a dry, damp or wet locations.
6. The suitability of input/output leads and the wring shall be determined in end product use.
Component sign accessories, Class 2 power supply, Model 701507-60W1-JV.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Model Number
701507-60W1-JV
Input
Input
Voltage (V) Current (A)
100-240
0.85
Frequency
(Hz)
Output Voltage
(Vdc)
Output Current
(A)
50/60
12
0-5
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and shall be spaced by standard j-box knockout spacings. from side to side.
4. For field wiring, when Junction Box is not provided on the primary circuit, each unit shall be provided with detailed Installation
Instructions requiring the installer to use a UL Listed Junction box suitable for use in wet location for primary leads connection.
5. These products are intended for use in a dry, damp or wet locations.
6. The suitability of input/output leads and the wring shall be determined in end product use.
SS LIGHT CO LTD
7 SINPUNG-DONG PALDAL-GU
SUWON-SI, GYEONGGI-DO 442-040 REPUBLIC OF KOREA
E346996
Class 2 LED Modules, KPL, PPL, DPL, OSPL, CPL, OCPL, KPL(W), DPL(W), OSPL(W), KR3, KB3, KG3, KY3, DR3, DB3, DG3,
DY3, KTW3, KTB3, KTR3, DTW3, DTB3, DTR3, WPL, WPL(W), WR3, WB3, WG3, WSPL, NSR3, NSG3, NSB3, NSR3, FPL,
KGL, DGL, KR2, KB2, KG2, DR2, DB2, DG2, DDL, KDL(W), DDL(W), KRD2, KBD2, KGD2, KYD2, DRD2, DBD2, DGD2, DYD2,
OSDL(W), OSGL, OSDL, KPL4, DPL4, KPL40, DPL40, KPL40(W), DPL40(W), OSPL40, OSPL40(W), OSPL4, FPL40, KOL, DOL,
KOR, DOR, KOB, DOB, KOG, DOG, DRGB3, WRGB3, WSRGB3, KRGB3, KSL, DSL, SSL, KSL(W), DSL(W), KR1, KB1, KG1,
DR1, DB1, DG1, NSR, NSG, NSB, DRGB2, SRGB2, KRGBD, DRGBD, SRGBD, KRGB2, KRGB40, DRGB40, SRGB40, KPL6,
DPL6, OSPL6, KPL, PPL, DPL, OSPL, CPL, OCPL, KPL(W), DPL(W), OSPL(W), KR3, KB3, KG3, KY3, DR3, DB3, DG3, DY3,
KTW3, KTB3, KTR3, DTW3, DTB3, DTR3, WPL, WPL(W), WR3, WB3, WG3, WSPL, NSR3, NSG3, NSB3, NSR3, FPL, KGL,
DGL, KR2, KB2, KG2, DR2, DB2, DG2, KDL, DDL, KDL(W), DDL(W), KRD2, KBD2, KGD2, KYD2, DRD2, DBD2, DGD2, DYD2,
OSDL(W), OSGL, OSDL, KPL4, DPL4, KPL40, DPL40, KPL40(W), DPL40(W), OSPL40, OSPL40(W), OSPL4, FPL40, KOL, DOL,
KOR, DOR, KOB, DOB, KOG, DOG, DRGB3, WRGB3, WSRGB3, KRGB3, KSL, DSL, SSL, KSL(W), DSL(W), KR1, KB1, KG1,
DR1, DB1, DG1, NSR, NSG, NSB, DRGB2, SRGB2, KRGBD, DRGBD, SRGBD, KRGB2, KRGB40, DRGB40, SRGB40, KPL6,
DPL6, OSPL6, SPL40, SPL4, SPL(W1), KRD, KBD, KGD, KYD, SDL, SDL(W1), SPL, SPL6, SCPL, ODL, OPL, OPL40, OPL4,
OPL6, KSL(W1), KDL(W1), CPL(W1), KPL4(W1), JRGB3, KR40, KB40, KG40, CSL(W1), CSR, CSB, CSG, WSL(W1), WSR,
WSB, WSG, WPL(W1), KOL-1C(W1), KOL-2C, KOL-2C(W1), KOR-2C, KOB-2C, KOG-2C, GPL, GPL(W1), GRGBD, GRGB3,
GRGB40, JGRGB3, GCS RGB, WGS RGB, WGRGB3, SSL(W1), SCPL(W1), SPL40(W1), JSRGB3, SCSL, SCSL(W1), SCS
RGB, WSSL, WSSL(W1), WSS RGB, WSPL(W1), WSL, GDL, GPL40, GPL40(W), EPL, GCPL, OPCB 5030 6 (3P), OPCB 5030 8
(3P), PCB 5030 6 (1P), PCB 5030 8 (3P), PCB 5030 6 (1P) KP1, PCB 5030 8 (3P) KP1, PCB 5030 6 (1P) KW1, PCB 5030 8 (3P)
KW1, RGB 5030 8 (3P), LRGB 5030 10 (3P), PCB 5030 (3P) R, PCB 5030 (3P) B, PCB 5030 (3P) G, PCB 4530 - 1C (2P), PCB
4530 W1 - 1C (2P), PCB 4530 R - 1C (2P), PCB 4530 B - 1C (2P), PCB 4530 G - 1C (2P), PCB 4545 - 2C (3P), PCB 4545 W1 2C (3P), PCB 4545 R - 2C (3P), PCB 4545 B - 2C (3P), PCB 4545 G - 2C (3P), GPCB 5030 8 (3P), GPCB 5030 8 (3P) W, GRGB
5030 8 (3P), LGRGB 5030 10 (3P), SPCB 5030 8 (3P), SPCB 5030 8 (3P) W, A/L S18, A/L S30, A/L S60, A/L PP18, A/L PP30,
A/L PP60, A/L S18 (W1), A/L S30 (W1), A/L S60 (W1), A/L PP18 (W1), A/L PP30 (W1), A/L PP60 (W1), A/L S18(R), A/L S30(R),
A/L S60(R), A/L PP18(R), A/L PP30(R), A/L PP60(R), A/L S18(B), A/L S30(B), A/L S60(B), A/L PP18(B), A/L PP30(B), A/L
PP60(B), A/L S18(G), A/L S30(G), A/L S60(G), A/L PP18(G), A/L PP30(G), A/L PP60(G), A/L RGB S18, A/L RGB S30, A/L RGB
S60, A/L RGB P18, A/L RGB P30, A/L RGB P60, A/L GS18, A/L GS30, A/L GS60, A/L GPP18, A/L GPP30, A/L GPP60, A/L GS18
(W1), A/L GS30 (W1), A/L GS60 (W1). A/L GPP18 (W1), A/L GPP30 (W1), A/L GPP60 (W1), A/L GRGB S18, A/L GRGB S30, A/L
GRGB S60, A/L GRGB P18, A/L GRGB P30, A/L GRGB P60, A/L SS18, A/L SS30, A/L SS60, A/L SPP18, A/L SPP30, A/L
SPP60, A/L SS18 (W1), A/L SS30 (W1), A/L SS60 (W1), A/L SPP18 (W1), A/L SPP30 (W1), A/L SPP60 (W1), WAL PP18, WAL
PP30, WAL PP60, WAL PP18 (W1), AL PP30 (W1), WAL PP60 (W1), WAL PP18(R), WAL PP30(R), WAL PP60(R), WAL
PP18(B), WAL PP30(B), WAL PP60(B), WAL PP18(G), WAL PP30(G), WAL PP60(G), WAL RGB P18, WAL RGB P30, WAL RGB
P60, WAL GPP18, WAL GPP30, WAL GPP60, WAL GPP18 (W1), WAL GPP30 (W1), WAL GPP60 (W1), WAL GRGB P18, WAL
GRGB P30, WAL GRGB P60, WAL SPP18, WAL SPP30, WAL SPP60, WAL SPP18 (W1), WAL SPP30 (W1), WAL SPP60 (W1).
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 12 V DC.
149
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Marking: Company name or trademark
and product designation.
STARTEC CO LTD
310-8 YUHYUN-RI
YANGCHON-MYEON
GIMPO-SI, GYEONGGI-DO 415-821 REPUBLIC OF KOREA
E350879
Class 2 LED Module, R03-25KN.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
SUNSIGNLED OPTO-ELECTRONICS CO LTD
2F BLDG B LAOBING INDUSTRY PARK
ZHOUSHI RD
SHIYAN TOWN BAOAN DISTRICT
518108 SHENZHEN, CHINA
E359615
Class 2 powered LED modules, Models IYX225U, IYX324U, IYX220U, IYX340U, IYX326U, IYX332U, IYX341U, MYX112U,
MYX120U, MYX102U, MYX117U, where X and Y may be replaced by any letter denoting LED color and type respectively.
1. This product is only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than electrical ratings.
3. This Class 2 LED module is rated as noted in the electrical ratings tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. This product is suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. This product is not required to be enclosed or protected from the weather in the end product.
6. This product may be secured in place in the end products by any means available.
SUPER BRIGHT LEDS INC
4400 EARTH CITY EXPY
EARTH CITY, MO 63045
E357849
LED Lighting Modules, Cat. Nos. LB4-x6, LBM-x2, LBM-x4, where "x" can be any alphanumeric combination.
1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory
Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to
draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, Cat. Nos. SWFLS-x60, SNFLS-x30, where "x" can be any alphanumeric combination.
1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited
to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.
4. These products are suitable for use in dry, damp and wet locations without additional enclosures.
LED Lighting Modules, Cat. Nos. LBM-x3SMD, LSM-x3X3, LSMCC-x1X3-LP, LSMCC-x3X3-LP[@], LSMCC-x4X3-LP[@], where
"x" can be any alphanumeric combination.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated greater than 15 V DC.
3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
SUPER X MFG LTD
UNIT 1001
FOOK LEE COMMERCIAL CENTRE
E347032
January 23, 2014
150
SIGN COMPONENTS MANUAL (SAM)
33 LOCKHART RD
WAN CHAI, HONG KONG
Class 2 LED Modules, Models LD-60-1-12V, LD-60-1-24V, LD-80-1-24V, LD-60-UV-24V, LD-60-UV-24V-SC, LD-60-UV-24VDIW, LD-60-UV-1214V, LD-60-1-24V-SC, LD-60-UV-1214V-SC.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1.
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below. Acceptance of higher ambient shall
be determined in end product use.
Model
Ta (°C)
LD-80-1-24V
40
LD-60-1-12V
40
LD-60-1-24V
40
LD-60-UV-24V
40
LD-60-UV-24V-SC
40
LD-60-UV-24V-DIW
40
LD-60-1-24V-SC
52
LD-60-UV-1214V
40
LD-60-UV-1214V-SC
40
4.
5.
These LED drivers are intended for use in dry and damp locations.
These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a
suitable enclosure shall be considered in the end product.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. The need of the grounding means shall be determined in the end product.
8. These LED drivers shall be enclosed within a suitable end product enclosure.
9. For model LD-60-UV-24V-DIW, the conduit knockout test was not conducted. The suitability is to be determined in end
product.
10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
11. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
Class 2 output LED drivers, Models LD-100-UV-24V-P6, LD-24-1-12V.
1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1.
2. These LED drivers are provided with Class 2 output.
3. These LED drivers are intended to be operated in a maximum 40°C ambient.
4. Model LD-100-UV-24V-P6 is intended for use in wet locations. Model LD-24-1-12V is intended for use in damp locations.
5. Model LD-100-UV-24V-P6 was provided with SJTW cord for input/output connection. Model LD-24-1-12V was provided with
AWM leads for input/output connection. The suitability of the wiring and the need for a suitable enclosure shall be considered in
the end product.
6. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
7. Models LD-24-1-12V shall be grounded through its mounting ears.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure. Otherwise, temperature test shall be conducted.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise. Otherwise, temperature test shall be conducted.
LED drivers, Models LD-10-1N-12V, LD-10-1N-24V, LD-100-UV-24V, LD-100-UV-12V, LD-12-1-0A35-FDIM, LD-24-1-24V, LD24-UV-12V, LD-24-UV-24V, LD-150-UV-24V-P6A, LD-60-UV-12V-P6B, LD-60-UV-12V-ALS, LD-60-UV-24V-P6B.
1. These LED drivers have been evaluated using resistive load.
2. These products have been evaluated with the following characteristics.
Model No.
Input type
Output is
Intended
Location
Connection
Ta, °C.
Input
Output
LD-10-1N-12V
[X] Branch Circuit
(Mains)
[X] Isolated
[X] Class 2
Damp
60
AWM
Leads
AWM
Leads
LD-10-1N-24V
[X] Branch Circuit
(Mains
[X] Isolated
[X] Class 2
Damp
60
AWM
Leads
AWM
Leads
LD-150-UV-24V-P6A
[X] Branch Circuit
(Mains)
[X] Isolated
[X] Non-Class 2
Wet
60
SJTW
Cord
SJTW
Cord
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
Wet
60
AWM
Leads
SJTW
Cord
SJTW
Cord
SJTW
Cord
[X] Branch Circuit
(Mains)
[X] Isolated
[X] Class 2
Wet
60
AWM
Leads
AWM
Leads
LD-60-UV-12V-P6B
LD-60-UV-12V-P6B-ALS
LD-60-UV-24V-P6B
[X]
151
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
LD-100-UV-24V
[X] Branch Circuit
(Mains
[X] Isolated
[X] Class 2
Damp
40
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains
[X] Isolated
[X] Non-Class 2
Damp
40
AWM
Leads
AWM
Leads
LD-12-1-0A35-FDIM
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
LD-24-1-24V
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
[X] Branch Circuit
(Mains)
[X] Isolated
Class 2
[X]
Damp
40
AWM
Leads
AWM
Leads
LD-100-UV-12V
LD-24-UV-24V
LD-24-UV-12V
5. The suitability of the input/output connection and the wiring in a suitable enclosure is also to be considered in end product use.
6. These products are intended for building in or mounted on the surface of end product. Acceptability of the LED driver with
respect to mounting, spacing, casualty, temperature and segregation are to be determined as part of the end device evaluation.
7. The suitability of grounding means shall be determined in the end-use product for models LD-10-1N-12V, LD-10-1N-24V, LD100-UV-24V, LD-100-UV-12V, LD-24-1-24V, LD-24-UV-12V, LD-24-UV-24V.
8. For models LD-10-1N-12V, LD-10-1N-24V, LD-12-1-0A35-FDIM, the suitability of the driver enclosure as final enclosure shall be
evaluated in end product.
9. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure. Otherwise, temperature test shall be conducted.
10. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise. Otherwise, temperature test shall be conducted.
SYDEMEX
ALTOS B
358 AV BENITO JUAREZ
COL JUAN JOSE RIOS 1
28984 VILIA DE ALVAREZ, COL MEXICO
E348149
Class 2 LED Modules, Models UBMM02, UBCMM02, UBFMM02, URMM02, UAMMM02, UAZMM02, UVEMM02, UBLA03S,
UBLC03S, UBLF03S, UROJ03S, UAZU03S, UVER03S, UAMA03S, UBLS03, UBLCS03, UBLFS03, UROS03, UAZS03, UAMS03,
UVES03, UBLCS03M, UBLCCS03M, UBLCFS03M, UROCS03M, UAZCS03M, UAMCS03M, UVECS03M.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp, and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
T-LED SYSTEM INC
8028 NW 68TH ST
MIAMI, FL 33166
E342484
Class 2 LED Module & Controller, designated “T-LED System”
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less in dry and damp locations.
2. These products are each rated max. 36 watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total
wattage of greater than the secondary or output rating of the Class 2 supply.
3. These products are for factory wiring only in sign or outline lighting related application.
4. The product has not been evaluated for use with dimmers. The suitability for use with dimmers shall be determined in the end
product.
TACTEC APLIED OPTOELECTRONICS
780 CORONADO CENTER DR STE 110
HENDERSON, NV 89092
E352708
Self-Ballasted Lamps, LED Type, Model TAO-SXX, where xx can be any numeric character.
1. These units have been tested in a 6 inch diameter can and test box per UL 1993. If the device is used in a different product or
configuration, consideration shall be given to re-conducting the Temperature Test.
2. These units have been evaluated for use in dry and damp locations. The use in other environments shall be considered in the
end product.
3. The need for additional end product markings, such as lamp replacement, shall be considered in the end product evaluation.
4. The units have been evaluated for use with standard wall dimmers.
Class 2 LED Modules, designated as TS-XXX-YYY, where XXX and YYY are any alphanumeric characters.
January 23, 2014
152
SIGN COMPONENTS MANUAL (SAM)
1. These products are suitable for use in dry, damp and wet locations when supplied with a Class 2 power source rated 24 Volt DC
or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
TAIWAN OASIS TECHNOLOGY CO LTD
348 SHAN YIN RD
KWEI SHAN SHIANG
TAOYUAN HSIEN, 333 TAIWAN
E325673
Class 2 LED Modules, TOLB series, Cat. Nos. TOLB-R36X36(3XX)YPX10-Z, TOLB-R40X17(3XX)YPX10-Z, TOLBR196X17(3XX)YP-Z, TOLB-R58X15(3XX)YPX10-Z, TOLB-R58X15(3XX)YPX10-Z; Cat. Nos. TOLC-2XXXX, -3XXXX, -4XXXX, 6XXXX, where XX may be any combinations of alpha characters from A through ZZ, where XXXX may be any combinations of alpha
characters from A through ZZZZ, Y may be any combinations of numeric characters from 0 through 99 and Z may be DC12V.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. These products are each rated max. 6 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
TECH 22
1160 JOSHUA WAY
VISTA, CA 92083
E192264
Controller/Dimmer for Neon Power Supplies, Model GEN-3, CNTM12-xxx, CNTM24-xxx.
1. Must be inside an electrical enclosure in the end product.
2. The controller/dimmer is intended to be used with neon supplies and solid state relays that have an optically isolated control
input rated 3 to 6 Volts, 2 to 10 mA.
3. The controller is rated for a 120 Volt input, 20 mA with an output of maximum 6 Volts, and 350 mA.
4. This controller is intended only for use in indoor and inside outdoor signs.
Dimmer Load, Cat. No. “Active load”.
1. Must be inside an electrical enclosure in the end product.
2. Dimmer load is for use with applicant's neon power supplies or controllers with 120 V dimmer control input.
3. Dimmer load for use in indoor signs or enclosed within outdoor signs.
o
4. This dimmer load has been evaluated in a 40 C ambient only.
5. If a heat producing component such as electrode, transformer or ballast is located within 3 in. of the dimmer load, a temperature
test should be conducted in the end product.
Electronic Incandescent Lamp Controller, Cat. No. Chase 004.
1. Must be inside an electrical enclosure in the end product.
2. Controller is only suitable for connection to a UL Listed or Recognized Class 2, 12 to 24 V dc or ac (50/60 Hz) power source.
3. Controller for use in indoor signs or within outdoor signs.
4. This controller has been evaluated in 40°C ambient.
5. If a heat producing component such as electrode, transformer or ballast is located within 3 in. of the controller, a temperature
test should be conducted in the end product.
Electronic LED and Incandescent Lamp Controller, Cat. Nos. CNTS3D-xxx, CNTS3A-xxx, CNTS4D-xxx, CNTS4A-xxx,
CNTS5D-xxx and CNTS5A-xxx.
1. Must be inside an electrical enclosure in the end product.
2. Controller is only suitable for connection to a UL Listed or Recognized Class 2, 12 to 24 V dc or ac (50/60 Hz) power source.
3. This controller is intended only for use in indoor and inside outdoor signs.
4. Shall not be located within 3 in. of heat producing components such as electrodes, transformers or ballasts.
LED Modules, Model designation LED strips XXX YYY, where XXX and YYY may be replaced with any alpha numeric character
from 000 to 999 or from AAA to ZZZ or combination of letter and numbers; T-lights XX YYY, model designation where XX and YYY
may be replaced with any alpha numeric character from 00 to 99 or from AA to ZZ or combination of letter and numbers; Spotlight
XXX where XXX may be replaced with any alpha numeric character from 000 to 999 or from AAA to ZZZ or combination of letter
and numbers; LED assembly XXXXXX, where XXXXXX may be replaced with any alpha numeric character from 000 to 999 or
from AAA to ZZZ or combination of letter and numbers. All models may or may not be followed with suffix KK, where KK may be
replaced with any alpha numeric character from 00 to 99 or from AA to ZZ or combination of letter and numbers.
1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. These Class 2 LED modules are each rated max. 60 Watts per unit. When units are connected to a Class 2 circuit, they are not
to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
TECHNI-LITE SYSTEMS INC
PO BOX 445
E315540
153
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
910 HIGH ST
PETERBOROUGH, ON K9J 6Z3 CANADA
Fluorescent Grids, Models LG17MF, LG25MF, LG32MF, LG17BX, LG25BX, LG32BX.
1. Sign Components LG17MF, LG25MF, and LG32MF being power supply cord connected are suitable for use only in indoor
portable power supply cord connected signs.
2. Sign Components LG17BX, LG25BX and LG32BX are suitable for use in a damp location within a sign where protected from
the weather.
3. The Electrical rating shall be as per table below.
RATING
120 V - 50/60 Hz
240 V - 50/60 Hz
MODEL
LG17MF, LG17BX
0.50 A
0.22 A
LG25MF, LG25BX
0.74 A
0.32 A
LG32MF, LG32BX
0.95 A
0.40 A
4. The maximum number of grids that can be inter-connected shall not exceed maximum number of units as noted below.
Model Number
Maximum Number of Units
LG17MF, LG17BX
12
LG25MF, LG25BX
8
LG32MF, LG32BX
6
5. Suitability of the branch supply connecting means and interconnecting means for models with suffix MF shall be evaluated in
the end use application.
TECLED ELECTRONIC INC
217 APACHE TRL
NORTH YORK, ON M2H 2W3 CANADA
E326777
LED Modules, TOLB series, Cat. Nos TX3012-Y-ZZ-1 series and TX5012-Y-ZZ-1 series where X may be L or S; Y may be any
numeric characters from 0 to 9; ZZ may be any combination of alpha characters from AA to ZZ.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. These products are each rated max. 6 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
TECHNOLUX INC
103 14TH ST
BROOKLYN, NY 11215
E248791
High Voltage Electrodes/GTO Splice End Cap, Model No. xxSC1yDB, where xx is 10, 12, 15 or 18 and y is B, G or W, For dry
locations only.
1. Model Nos. xxSC1yDB and xxSC1y are suitable for use in USL Listed Signs when marked for Dry or Damp Locations Only.
Model Nos. xxSC1yDB are suitable for use in CNL Listed Signs when marked for Dry Locations Only.
2. They have been evaluated with GTO cable with integral sleeving, cat. no. GTO15 (14 through 18 AWG) and GTO10 (18AWG)
manufactured by Silitherm S.R.L. only. Use with any other GTO type or manufacture will need to be evaluated in the end product.
3. Models 18SC1xDB and 18SC1x are additionally rated for 100mA
TEN PAO INDUSTRIAL CO LTD
6TH FL, ROOM 10-11
KWONG SANG HONG CENTRE
KWUN TONG, 151-153 HOI BUN RD
KOWLOON, HONG KONG
E348519
Class 2 LED Module, Model S060BN1200500.
1. The output of the unit complies with Class 2 criteria of UL 1310 and CSA C22.2 No. 223-M91.
2. The product is provided with 18 AWG input and output leads. The suitability of the wiring and the need for a suitable enclosure
shall be considered in the end product.
3. The product is provided with 1.0 mm thick aluminum enclosure, the suitability of the enclosure as ultimate enclosure shall be
determined in the end use application.
4. The product is intended for use in dry and damp locations.
5. The product is to be used in a maximum 50°C ambient temperature.
6. The units are intended for factory wiring only.
7. The product is of the constant voltage type that requires the proper number of LED modules and controllers that does not
exceed the maximum output current.
8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
9. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
January 23, 2014
154
SIGN COMPONENTS MANUAL (SAM)
THE BRIGHT GROUP PTY LTD
106 DERBY ST
SILVERWATER
SYDNEY NSW 2128, AUSTRALIA
E245307
Class 2 LED Module, Series TBG-ELP-X-YYYY-ZZ-QQQ, may be provided with additional suffixes.
1. These components are to be installed in accordance with the manufacturer's instructions in the end product.
2. These products are only suitable for connection to a Class 2 power source, rated 24 Volt or less.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits rated greater than 24 V.
4. These devices are rated as specified below.
Catalog Number
Max. Rated Input
TBG-ELP-X-YYYY-ZZ-QQQ
Type Load
V
A
12
0.50
LED
24
0.25
LED
5. When marked for use in Canada, consideration for conducting a temperature test in the end product shall be considered.
6. These products are suitable for use in dry, damp and wet locations.
Cold cathode fluorescent light assemblies Product Designations: specified in the Table below.
Cat. No.
Lamps
No.
Ratings
Designation
Input Volts, V Input current, A Output Volts, V
TBG-INV04-12V 1 or 2 8 watt max., singly or in combination from 10
to 73 cm long cold cathode type
TBG-INV04-24V
12 VDC
0.7
850 VAC
24 VDC
0.35
850 VAC
1. These lamp and ballast assemblies are intended for use in gaming equipment, point of sale (POS), and other similar sign
applications.
2. The acceptability of the supply connecting means shall be determined in the end use. The supply connecting means is striped,
insulated wire; wire is 20AWG, which is acceptable for sign applications.
3. The ballast was tested and found to be acceptable for use in a 40 °C ambient temperature. Acceptable operation at a higher
temperature should be determined. When multiple ballasts are assembled into sign applications the ballasts can be spaced 1inch end-to-end and 4-inch side-to-side - minimum.
4. The ballast and its associated supply and lamp wires need to be in suitable electrical enclosure.
Cold cathode fluorescent light assemblies, Product Designations: specified in the Table below.
Lamps
Cat. No.
Ratings
Input Volts,
Input
V
current, A
Output
Volts, V
No.
Designation
LPS-INV40-24
1 or 2
400 mm long, cold cathode type
24VDC
.45
900 VAC
LPS-INV40-12
1 or 2
400 mm long, cold cathode type
12VDC
.9
900 VAC
LPS-INV03-24
1 or 2
300 mm long, cold cathode type
24VDC
.35
850 VAC
LPS-INV03-12
1 or 2
300 mm long, cold cathode type
12VDC
.67
850 VAC
LPS-INV02-24
1 or 2
200 mm long, cold cathode type
24VDC
.25
680 VAC
LPS-INV02-12
1 or 2
200 mm long, cold cathode type
12VDC
.50
670 VAC
LPS-INV01-24
1 or 2
100 mm long, cold cathode type
24VDC
.20
450 VAC
LPS-INV01-12
1 or 2
100 mm long, cold cathode type
12VDC
.35
430 VAC
Cold Cathode type Lamps
Ratings
No.
Designation
Input Volts,
V
TBG-INV40A-24V
1 or 2
400 mm long
24VDC
0.38
1030 VAC
TBG-INV03A-12V
1 or 2
300 mm long
12VDC
0.67
989 VAC
TBG-INV03A-24V
1 or 2
300 mm long
24VDC
0.38
953 VAC
TBG-INV02A-12V
1 or 2
200 mm long
12VDC
0.55
813 VAC
TBG-INV02A-24V
1 or 2
200 mm long
24VDC
0.28
754 VAC
TPG-INV01A-12V
1 or 2
100 mm long
12VDC
0.46
850 VAC
TBG-INV01A-24V
1 or 2
100 mm long
24VDC
0.25
812 VAC
Cat. No.
Input Current
Amps
Output Volts,
V
1. These lamp and ballast assemblies are intended for use in gaming equipment, point of sale (POS), and other similar sign
applications.
2. The acceptability of the supply connecting means shall be determined in the end use. The supply connecting means is striped,
insulated wire; wire is 20AWG, which is acceptable for sign applications.
155
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. The ballast was tested and found to be acceptable for use in a 40 °C ambient temperature. Acceptable operation at a higher
temperature should be determined. When multiple ballasts are assembled into sign applications the ballasts can be spaced 1inch end-to-end and 4-inch side-to-side - minimum.
4. The ballast and its associated supply and lamp wires need to be in suitable electrical enclosure.
Cold cathode fluorescent light assemblies, Designated TBG-UNITOP-XXX, where XXX may be any alphanumeric characters.
1. These components are to be installed in accordance with the manufacturer's instructions in the end product.
2. These products are only suitable for connection to a Class 2 power source, rated 24 Volt or less.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits rated greater than 24 V.
4. These devices are rated as specified below.
Max. Rated Input
Catalog Number
V
A
Type Load
TBG-UNITOP-XXX
24
1
Cold Cathode Fluorescent and LED
5. No tests have been conducted on these components and as such, end product testing should be considered.
6. Suitability of the input leads (AWG, temperature rating, etc…) and the supply connector shall be considered in the end product.
7. When marked for use in Canada, consideration for conducting a temperature test in the end product shall be considered.
8. These products are suitable for use in dry locations only.
TIVOLI LLC
15602 MOSHER AVE
TUSTIN, CA 92780 USA
E363009
Class 2 LED modules, Cat. No. FXLM-XX-M-24, where XX can be RD, YL, BL, GR, 50, 41, 32, 28.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC, 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than the electrical ratings.
3. These Class 2 LED modules are each rated as noted in the electrical ratings tables. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. The suitability of supply leads shall be determined in end use.
TRANSCO TO GO LLC
1059 COLITE DR
WEST COLUMBIA, SC 29170
E129809
Polymeric neon electrode enclosure, Model ECDB or ECS, followed by 7 or 8, followed by 10, 12, 13 or 15.
1. This product has been evaluated for use with systems rated 15 kV, open circuit, and 7.5 kV to ground.
2. This product has been investigated for use in Dry and Damp locations.
3. This product is suitable for use within a 1/2“ trade size conduit opening.
Molded Silicone Rubber Boot/Nut Assembly, Model 1100, may be followed by CHECL, may be provided with a WOYR2 switch
by Transco, Model 1000.
1. This device is intended to be used in outdoor electric sign applications where the boot/switch toggle are protected from
inadvertent abuses. The suitability of protective barrier shall be determined in the end-use application.
2. Consideration shall be given to conducting a Water Exclusion Test as a regular part of each inspection. The suitability of a
Listed toggle switch for use with this boot shall consider the following:
(A) The toggle (switch actuator) shall be metal, and
(B) The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot.
(C) The assembly shall be mounted on the bottom or side surface of a sign body only.
3. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the switch
enclosure are to be provided in accordance with UL 48.
4. The Molded Silicone Rubber Boot/Nut assembly may be optionally provided with a WOYR2 switch by Transco, Model 1000
rated 20 A, 120-277 Vac; 7.5 A, 125VL; 3HP, 120/240 Vac.
Transformer Box, Model No. 18TB-TPO,20TB-TP0
1. This product is suitable for Wet Locations.
2. When installed in outdoor, damp or wet location, drill a min. of 2 drain holes in the bottom. Hole size min. ¼” to max ½”. Elevate
transformer ½” from bottom.
3. Transformer and Transformer box shall be properly grounded in the end product.
4. Spacings from the live parts to dead metal shall be considered in the end product.
Porcelain Panel Bushing, Model 1043-A
1. This product has been evaluated for use with systems rated max 15 kV open circuit, and 7.5 kV to ground
2. This product has been investigated for use in Dry and Damp locations.
3. This product is suitable for use within a 1/2ˮ trade size conduit opening.
Tension Clip, Part No. Trans-clip SB and Trans-clip SC
1. The suitability of these tensioning systems in combination with any Recognized flexible sign face material (UYMR2) and UL 48
to prevent entrance of water in outdoor sign applications, shall be determined.
2. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face
requirements of UL 48 particularly clearance to lamps and lampholders.
3. These tensioning systems in conjunction with the Recognized flexible face material have not been investigated for use as an
electrical enclosure.
4. The suitability of the "fit" of the face material and the secureness of the clamping system on the sign, shall be judged in the end
application.
January 23, 2014
156
SIGN COMPONENTS MANUAL (SAM)
5. When these systems secure flexible faces on signs with any dimension (length or width) greater than 6 ft, suitable braces should
be employed to prevent the material from billowing and creating short spacings to heat sources.
6. The tension clips shall be mounted not more than 12 in. apart on center.
Neon Supply Systems - EIK and EWS Series may be provided with “-W” designator to indicate wet location system provided
1. All transformers are pre-mounted and spaced to maintain minimum 1-1/2 inches between any high voltage terminals and
grounded dead metal.
2. If provided with “-W” designation the Neon Supply System has been provided with a Transformer Mounted 1/2 in. off bottom of
enclosure and the enclosure has been provided with two 3/8 in. drain openings.
3. For EIK Series, the models are provided with Listed Integrally Sleeved GTO Cable and Listed Polymeric Splice Enclosures
(Boots) that have previously been investigated to the requirements of UL's UYTA Classification Program.
4. Mounting of the WOYR2, Model 1000 Toggle Switch and UYMR2, Model 1100, 1100NSZ or 1100CCJ Toggle Switch Boot
Cover shall be evaluated in the End-Product Assembly per the requirements found in the Sign Components Manual.
5. For EIK Series, one end of the integrally sleeved GTO Cable may be provided with a Listed (ZMVV) uninsulated ring terminal
that is suitable for the application and has been secured per the manufacturer's specifications.
High Voltage Splice Box, Model TC-HV II, TC-HV III
1. These products are suitable for use with a system with a maximum open circuit voltage of 15 kV and 7.5 kV to ground.
2. These products are suitable for use in Wet Locations.
3. For installation in dry locations, at least 63.5 mm (2.5 in) of GTO cable insulation is required to be left on each cable entering
the enclosure as measured from the point where the cable enters the inside area of the enclosure and the high voltage terminal.
For a GTO cable splice enclosure suitable for use in damp and wet locations the instruction shall specify the minimum insulation
on the GTO Cable to be at least 10.1 cm (4 in).
Electrode Receptacle Insulators, Models 1030-8, 1030-10 and 1030-12.
1. This product is an insulator and has not been evaluated as an enclosure.
2. Limited to use inside dry, damp and wet location signs and outline lighting where not subject to precipitation.
3. Rated for a maximum 15kV, 7.5 kV to ground.
Transformer Box, Model TRA-LED-FPO.
1. This product is suitable for Wet Locations.
2. When installed in outdoor, damp or wet location, elevate transformer 1/2 in. from bottom and mount 12 in. above any horizontal
surface.
3. The transformer box is to be installed with the knockout holes facing down and the cover facing out.
4. LED Drivers and Transformer Box shall be properly grounded in the end product.
5. Spacings from the live parts to dead metal shall be considered in the end product.
TRANSPORTATION CONTROL SYSTEMS INC
1059 COLITE DR
WEST COLUMBIA, SC 29170
E464766
LED Tube Lamp, Models LED-XXXX-HO-UL-3-XX, LED-XXXX-HO-UL-3.5-XX, LED-XXXX-HO-UL-4-XX, LED-XXXX-HO-UL-4.5XX, LED-XXXX-HO-UL-5-XX, LED-XXXX-HO-UL-5.5-XX, LED-XXXX-HO-UL-6-XX, LED-XXXX-HO-UL-6.5-XX, LED-XXXX-HOUL-7-XX, LED-XXXX-HO-UL-7.5-XX, LED-XXXX-HO-UL-8-XX, LED-XXXX-HO-UL-8.5-XX, LED-XXXX-HO-UL-9-XX, LED-XXXXHO-UL-9.5-XX, LED-XXXX-HO-UL-10-XX. Model No. may be provided with suffix "X", where "X" can be any number or letter.
Models SN-T8-2FT-XX, SN-T8-3FT-XX, SN-T8-4FT-XX, SN-T8-5FT-XX, SN-T8-8FT-G13. Where "X" represents lamp base type,
G13 OR G5.
1. The LED Tube Lamps have been evaluated for use in dry and damp locations.
2. The LED tube lamps are for use in the horizontal mounting position only.
3. The LED tube lamps shall not be used with instant start type lampholders marked “I” unless the shunt jumper wire is removed.
4. The LED Tube Lamps were only evaluated for factory installation in electric signs. Use in other applications requires evaluation.
5. Connect power to only one end of lamp. The other end is not connected to any electrical power and it serves as means of
mechanical support only.
6. These lamps are not for use on dimmer circuits.
TRANSITIONS DIGITAL GRAPHICS LLC
3 W LOS OLIVOS ST
SANTA BARBARA, CA 93105-3927
E334318
Class 2 LED Module & Controller, designated as EL-ASM-T0X, where X may be any number between 0 to 9.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated max 12 VDC.
3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
4. When units are connected to a Class 2 circuit, their ratings are to be limited to draw a total wattage of no greater than the
secondary current rating of each Class 2 power supply.
5. These products are suitable for use in dry locations.
TRI-MAG LLC
1601 N CLANCY ST
VISALIA, CA 93291
E309796
LED Power Supply with Class 2 output, Models TMG-Z016-W, TMG-Z336.
1. These power supplies have a maximum of two Class 2 output. The output of these power supplies has been evaluated to Class
2 output requirements for dc circuits.
2. These power supplies have not been provided with a suitable enclosure. In the end product these units shall be enclosed.
3. When used in a cord-connected products, the need for conducting a leakage current test shall be considered in the end product.
157
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
4. The product was tested for use at the maximum ambient temperature (Tma) of 65°C permitted by the manufacturer's
specification. This product will need to be temperature tested in the end product and the results cannot exceed 65°C.
5. This product is intended for use in changing message signs.
6. These products with Class 2 outputs are suitable for use in dry and damp location.
7. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure.
TRIAD MAGNETICS
22520-B TEMESCAL CANYON RD
CORONA, CA 92883
E305150
LED sign system, Models TLD1020-10-Cnnnn, TLD1020-12-Cnnnn, TLD1020-13-Cnnnn, TLD1020-15-Cnnnn, TLD1020-17Cnnnn, TLD1020-18-Cnnnn, TLD1020-22-Cnnnn, TLD1020-24-Cnnnn (#), TLD1020-36-Cnnnn (#), TLD1040-09-Cnnnn, TLD104010-Cnnnn, TLD1040-12-Cnnnn (#), TLD1040-13-Cnnnn, TLD1040-15-Cnnnn, TLD1040-18-Cnnnn, TLD1040-22-Cnnnn, TLD104024-Cnnnn (#), TLD1040-36-Cnnnn (#).
Where the optional suffix "Cnnnn" may be any alphanumeric character. (#)- May be followed by -H
1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate
application.
2. These units are provided with a Class 105(A) insulation system.
3. The suitability of the input and output connections shall be determined in each end use application.
4. These power units are intended for dry or damp location use only.
5. Strain Relief and Impact Tests have not been investigated.
6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of
each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.
TRIDONIC GMBH & CO KG
FAERBER GASSE 15
6850 DORNBIRN, AUSTRIA
E313318
Class 2 LED Modules, Cat. Nos. Cat. No. PXXX-AAAA YYY Series, where XXX can be 503, 510, 515, 540, 550 and 560; optional
AAAA can be any alphanumeric character combination; and YYY can be any alphanumeric character combination from 000 to 999
incl., AAA to ZZZ incl. or any combination of letters and numbers.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 12 V.
3. Class 2 LED modules, Cat. No. Cat. No. PXXX-AAAA YYY series are each rated max. 18 Watts per unit, except Model P516-2
is rated max. 23 watts. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the
secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules, Cat. No. L51K-AABB YYY series, where L may be replaced with D; K may be replaced with 1 or 6; AA and
YYY may be any combinations of alphanumeric characters; and BB may be any combinations of alphanumeric characters or blank.
1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 14 Volt
DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are not required to be enclosed or protected from the weather in the end product.
4. These products may be secured in place in the end product by any means available.
Class 2 LED Modules, Sign Accessories, Class 2 LED Modules, designated as "TALEXXengine IMAGE" Cat. No. IMA-AAABBBCCCDDDEEEFFFGGGHHHIIIJJJ Series, where AAA may be replaced with CLA, SEL or PRE and
CCCDDDEEEFFFGGGHHHIIIJJJ may be replaced with any combinations of alphanumeric characters or blank.
1. These products are only to be powered by a Class 2 power source rated 48 Volt DC or less.
2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
3. These products are suitable for use in dry or damp locations only.
4. These products may be secured in place in the end product by any means available.
5. When the rated input is above 42.4 VDC, the units are only suitable for use in the United States only.
Power Supply with Class 2, Models LCU 060/12 D, LCU 035/12 D XX and LCU 015/12 D, where X=A~Z, 0~9 or blank.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Input
Output
Output
Input
Input
Current
Power
Voltage (V
Output
Power
Model No.
Voltage (V)
Freq (HZ)
(A)
Factor
dc)
Current (A)
(W)
LCU 060/12 D
120-240
50/60
0.75
0.95
12
5.0
60
LCU 035/12 D XX
120-240
50/60
0.39
0.95
12
2.92
35
LCU 015/12 D
120-240
50/60
0.35
0.4
12
1.25
15
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end
and 101.6 mm (4 in) from side to side.
4. These products shall be enclosed in suitable electrical enclosure in the end product.
5. These products are suitable for factory wiring only.
6. The load powered by the Class 2 output of these power supplies at the 12 Vdc rating or less is suitable for use in dry, damp and
wet locations.
7. These products have been tested in oven at 50ºC ambient, with the following maximum case temperatures, Tc:
January 23, 2014
158
SIGN COMPONENTS MANUAL (SAM)
For model LCU 060/12 D the Tc = 82ºC; for model LCU 035/12 D XX the Tc = 64ºC; for model LCU 035/12 D XX the Tc=74ºC.
8. These products are intended for use in a dry or damp locations only.
9. The suitability of input/output leads and the wring shall be determined in end product use.
10. The metal case of Model LCU 015/12 D is not grounded. The proper grounding means of this product shall comply with the
end product requirements.
Class 2 LED modules, Models P541-CLA, P551-SEL.
1. These products are only suitable for connection to a Class 2 power source rated 14 V DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated at 14 V DC or less.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 14 V DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Low voltage dimmers, designated LNU S, LNU M.
1. These devices, including all connections have only been evaluated for factory installation.
2. These controls have not been evaluated for safety or limiting applications. They have been evaluated for regulating function
only.
3. The suitability of the connections, including spacing, shall be determined in the end-use application.
4. The devices shall be mounted within a suitable ultimate enclosure and the suitability of mounting means shall be determined in
end-product applications.
5. LNU S is only for Use with LNU M, and a maximum of 19 LNU S can by sync'd to 1 LNU M.
TRONICC TECHNOLOGIES
18584 BUDGE
PIERREFONDS, QC H9K1K8 CANADA
E357992
Sign accessories, Class 2 LED modules, TT-M-01, TT-M-02, TT-M-03, TT-M-04, TT-B-01.
1. These products were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2
source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limiting requirements.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry and damp locations.
5. Consideration for the installation and power supply connection and interconnection is to be determined in the end-use
application.
TUBE LIGHTING PRODUCTS
1346 PIONEER WAY
EL CAJON, CA 92020
E348777
Class 2 LED Strip, Model DSH Series.
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations.
4. These products do not require an electrical enclosure.
5. These products may be secured in place in the end product by any means available.
U S LED LTD
6807 PORTWEST DR
HOUSTON, TX 77024
E226833
Class 2 LED Module, Model MY-12-K-XX "MegaX" Series, where Y may be replaced by any number from 0 to 99 incl., K may be
replaced by W, R, B, Y, G or RO and XX is optional, where it may be replaced by any alphanumeric characters (0 to 99 incl. or A
to Z incl. or combinations). .
1. These products are only suitable for connection to a Class 2 power source, rated max 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
3. These Class 2 LED Modules are each rated 0.77 Watts per unit. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated
24 VDC, these products are suitable for dry and damp locations only.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Accent Module, Mega, Accent or Right Light Series, Model Q ABC-XX-YY-ZZZZ series, where Q may be P, M, AC or blank;
AB, XX and YY may be replaced by any alphanumeric characters (0 to 9 incl. or A to ZZ incl. or combinations); C may be blank
or may be any alphanumeric characters (0 to 9 incl. or A to Z incl. or combinations); and ZZZZ may be any alphanumeric
characters (0 to 9999 incl. or A to ZZZZ incl. or combinations) or blank.
1. These products are only suitable for connection to a Class 2 power source, rated max 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit.
159
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
3. These Class 2 LED Modules are each rated 0.77 Watts per unit. When units are connected to a Class 2 circuit, they are not to
draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated
24 VDC, these products are suitable for dry and damp locations only.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Accent LED module, Model AC-X-Y-Z-T, where X is the length of the module, Y identifies the operating voltage, Z identifies
the color, and T identifies a standard.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2, max 30 Vdc only power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are not provided with break points in the printed wiring board. No cuts across the board is permitted.
4. These products are suitable for use in dry, damp, and wet locations.
5. These products are not required to be enclosed or protected from weather.
Right Light Series LED module “Right Light”, Models TP-2-12-z, abc-X-Y-Z and RLS-X-Y-Z, where X may be any number from 0
to 9, Y may be any number from 00 to 99, and Z may be any alphanumeric character..
1. These products are only suitable for connection to a UL Listed or Recognized Class max. 24 VDC power source.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are not provided with break points in the printed wiring board. No cuts across the board are permitted.
4. These products are suitable for use in dry, damp, and wet locations.
5. These products are not required to be enclosed or protected from weather.
LED Driver Enclosure, Model Life Extender Box.
1. This product has been evaluated for Dry and Damp Locations only. If used in a wet location, Rain Testing shall be conducted
during the end product evaluation.
Class 2 LED Module, Models EXSA-1-6, EXSA-1-12.
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated
24 VDC, these products are suitable for dry and damp locations only.
4. These products do not require an electrical enclosure. The 24Vdc modules require protection from the weather in the end
product, as they are not suitable for wet locations. The 12Vdc modules require no such protection.
5. These products may be secured in place in the end product by any means available.
Class 2 LED Module, Models Tandem XX and Tandem XX Dual, where XX, a non-safety related designation, may be any
alphanumeric character.
1. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit and is rated less than 24V DC.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V AC or 30 V DC max.
4. These products do not require an electrical enclosure.
5. These products may be secured in place in the end product by any means available.
Class 2 LED Module,“BE1” series, designated as Models BE1-W-XY-ZZ series, Where W may be any number from 0 to 9, X may
be any number from 0-9, Y may be L or Hand ZZ may be any two digit number between 0-9.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2 power source with max. 24 VDC.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. These products are provided with break points in the printed wiring board. No cuts across the board are permitted except where
indicated in the installation instructions.
4. These products are suitable for use in dry, damp, and wet locations.
5. These products are not required to be enclosed or protected from weather.
6. These products may be secured in place in the end product by any means available
UNILUMIN GROUP CO LTD
BLDG A, 112 YONGFU RD
QIAOTOU, FUYONG TOWN
BAOAN DISTRICT
SHENZHEN, GUANGDONG 518103 CHINA
E330828
Changing Message Signs, Model P16.
1. Maximum of 2 units when installed in a 15 Amp branch circuit and 3 units for a 20 Amp branch circuit.
2. This product was tested for use at a room ambient temperature of 25°C. Testing was conducted on an open bench positioned in
a vertical position facing horizontally. The need for conducting temperature testing in the end product shall be considered where
the units are installed in a higher ambient.
3. The suitability of the mounting means shall be determined in the end use.
4. The Rain Test per UL 879 was performed only on the face of the LED sign with the top sides and back sealed for testing.
Suitability for outdoor use when installed in the overall sign construction shall be considered in the end product evaluation.
UNION ELECOM CO LTD
102-1207 CHUNUI TECHNO PARK 1
200-1 CHUNUI-DONG
WONMI-KU
E362059
January 23, 2014
160
SIGN COMPONENTS MANUAL (SAM)
BUCHUN-SI, 420-857 REPUBLIC OF KOREA
Class 2 output power supply, Model UP40S12W1.
1. This Power Supply complies with the Class 2 output requirements and have a maximum of one Class 2 outputs.
2. This unit is suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
4. These products are provided with the following electrical ratings:
Model No.
Input
Voltage
(Vac)
Input
Frequency
(Hz)
Power
Consumption(W)
Input
Current
(A)
Output
Voltage
(Vdc)
Output
Current
(A)
Output
Wattage
(W)
UP40S12W1
100-120
50/60
49
0.84
12
3.3
40
5. This product shall be enclosed in the end product.
6. In the end product, power supply shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
7. The unit is intended for being used in fixed signs.
8. The input and output connections have been investigated for factory wiring only. The need for other consideration should be
considered in end-use product.
Component sign accessories, Non-Class 2 LED power supply, Model UP150S12W1.
1. These units are suitable for use in dry and damp locations.
2. These products are provided with the following electrical ratings:
Model No.
Input
Voltage
(Vac)
Input
Frequency
(Hz)
Power
Consumption(W)
Input
Current
(A)
Output
Voltage
(Vdc)
Output
Current
(A)
Output
Wattage
(W)
UP150S12W1
100-120
50/60
176
2.54
12
12.5
150
3. These products shall be enclosed in the end product.
4. In the end product, power supply shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
5. The unit is intended for being used in fixed signs.
6. The input and output connections have been investigated for factory wiring only. The need for other consideration should be
considered in end-use product.
7. This product is intended to be used in the condition Variable Resister (VR1) set to 190~450 Ohm.
8. The Power Supply has been temperature tested in a 40 °C ambient, where the maximum temperatures on the outer surface of
the enclosure above Transformer (T1) reached 83.1 °C. The need for further evaluation of the internal components shall be
considered if enclosure temperatures exceed this value when subjected to temperature testing in the end product.
Component sign accessories, Class 2 LED power supply, Model UP60S12W1.
1. This Power Supply complies with the Class 2 output requirements and has a maximum of one Class 2 outputs.
2. This unit is suitable for use in dry and damp locations.
3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
4. This product is provided with the following electrical ratings:
Model No.
Input
Voltage
(Vac)
Input
Frequency
(Hz)
Power
Consumption(W)
Input
Current
(A)
Output
Voltage
(Vdc)
Output
Current
(A)
Output
Wattage
(W)
UP60S12W1
100-120
50/60
74
1.11
12
5.0
60
5. This product shall be enclosed in the end product.
6. In the end product, power supply shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
7. The unit is intended for being used in fixed signs.
8. The input and output connections have been investigated for factory wiring only. The need for other consideration should be
considered in end-use product.
9. The Power Supply has been temperature tested in a 40°C ambient, where the maximum temperatures on the outer surface of
the enclosure above Transformer (T1) reached 64.9 °C. The need for further evaluation of the internal components shall be
considered if enclosure temperatures exceed this value when subjected to temperature testing in the end product.
Component sign accessories, Non-Class 2 LED power supply, Model UP100S12W1.
1. These units are suitable for use in dry and damp locations.
2. These products are provided with the following electrical ratings:
Model No.
Input
Voltage
(Vac)
Input
Frequency
(Hz)
Power
Consumption(W)
Input
Current
(A)
Output
Voltage
(Vdc)
Output
Current
(A)
Output
Wattage
(W)
UP100S12W1
100-120
50/60
125
1.85
12
8.4
100
3. These products shall be enclosed in the end product.
4. In the end product, power supply shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less
than 4 inches (102mm) apart when arranged otherwise.
5. The unit is intended for being used in fixed signs.
6. The input and output connections have been investigated for factory wiring only. The need for other consideration should be
considered in end-use product.
161
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
7. This product is intended to be used in the condition Variable Resister (VR1) set to 200~450 Ohm.
8. The power supply has been temperature tested in a 40 °C ambient, where the maximum temperatures on the outer surface of
the enclosure above Electrolytic Capacitors (C1) reached 67.3 °C. The need for further evaluation of the internal components
shall be considered if enclosure temperatures exceed this value when subjected to temperature testing in the end product.
UNIVERSAL LIGHTING TECHNOLOGIES
1430 WALL TRIANA HWY
MADISON, AL 35756
E315636
LED Class 2 Modules, Cat. Nos. LEDP503X-YY(@), LEDP510X-YYLEDP515X-YY(@), where (@) X can be R, A, G, B, O, NW,
DL or YW, YY can be 8V or 12V.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 12 V.
3. Class 2 LED modules when units are connected to a Class 2 circuit, are not to draw a total wattage of greater than the
secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Class 2 Modules, Cat. Nos. LMA-25R, LMA-25W, LMA-25B, LMA-25G, LMA-25WW.
1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 power
supply.
2. These components have not been evaluated for use when connected to a power source that does not comply with Class 2
requirements.
3. Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical
enclosure.
4. All models are suitable for use in dry, damp and wet locations.
5. Lead wires (R/C) (AVLV2) rated 300 V minimum, 80ºC minimum.
LED Power Supply with Class 2 output, Model L12V60UNVM.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a max. of one Class 2 output.
2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
wet locations.
3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and
min. 2 inches spacing to top of enclosure.
4. This product is rated as follows:
Input (ac)
Model
L12V60UNVM
Output (dc)
V
A
Hz
V
A
100-240
277
0.8
0.3
50/60
12
5.0
5. This product shall be enclosed in the end product.
6. This power supply is suitable for use in dry and damp locations.
7. These products are suitable for factory wiring only.
LED Power Supply with Class 2 output, Models L12V60UNV-A and D12V60UNV-A.
1. The power supply shall be installed in compliance with the applicable requirements of the end-product standard for, mounting,
spacing, casualty and segregation.
2. The maximum available output parameters were within the maximum allowable limits for Class 2, inherently limited as specified
in the UL 1310, Standard for Class 2 Power Units and also in accordance with the Canadian Safety Standard CSA C22.2 No.
223.
3. The power supply was submitted and tested for a maximum manufacturer's recommended Tc location, should not exceed 69°C,
in ambient of 40°C. If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature
test shall be conducted in the end use product.
4. Power Supply is intended for use in indoor Dry and Damp location only.
5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
any other direction.
6. The input and output leads were not subjected to the strain relief test.
7. The primary (Black-White) and the output (Red-Black) connection wires of the power supply are R/C (AVLV2/AVLV8), 18 AWG,
90ºC. The suitability of the leads shall be determined in the end-use application.
LED Power Supply with Class 2 output, Models D24V100UNV-A, L24V100UNV-A.
1. The power supply shall be installed in compliance with the applicable requirements of the end-product standard for enclosure,
mounting, spacing, casualty and segregation.
2. The maximum available output parameters were within the maximum allowable limits for Class 2, inherently limited as specified
in the
UL 1310, Standard for Class 2 Power Units and also in accordance with the Canadian Safety Standard CSA C22.2 No. 223.
3. The power supply was submitted and tested in an ambient of 40ºC. When evaluated in the end use, the Tc location as indicated
on the label should not exceed 67°C.
4. Power Supply is intended for use in indoor Dry and Damp location only.
5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of housing. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
any other direction. If required spacings are not provided, a temperature test is required.
6. The input and output leads were not subjected to the strain relief test.
7. The primary (Black-White) and the output (Red-Black) connection wires of the power supply are R/C (AVLV2), (AVLV8)/CN, 18
AWG, 90ºC. The suitability of the leads shall be determined in the end-use application.
8. The metal case must be grounded in the end use.
January 23, 2014
162
SIGN COMPONENTS MANUAL (SAM)
LED Class 2 Modules, designated as Cat. Nos. LSA-25W, LSA-25WH, LSA-25R and LSA-25WW.1. These products are only
suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
4. These products are not required to be enclosed or protected from the weather in the end product.
5. These products may be secured in place in the end product by any means available.
LED Power Supply with Class 2 output, models L12V60UNV-Q, and D12V60UNV-Q.
1. The drivers shall be installed in compliance with the applicable requirements of the end-product standard for, mounting, spacing,
casualty and segregation.
2. The maximum available output parameters were within the maximum allowable limits for Class 2, inherently limited as specified
in the UL 1310, Standard for Class 2 Power Units for wet location and also in accordance with the Canadian Safety Standard
CSA C22.2 No. 223.
3. The drivers were tested for a maximum manufacturer’s recommended Tc location, should not exceed 69°C, in ambient of 40°C.
If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be
conducted in the end use product.
4. The drivers are suitable for use in “DRY”, “DAMP”, and “WET” locations.
5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in
any other direction.
6. The input and output leads were not subjected to the strain relief test. However, the drivers are potted and the need to perform
the Strain Relief and/or Pushback Relief Tests on the lead wires should be determined in the end-use application.
7. The primary (Black/White/GREEN) and the output (Red-Black) connection wires of the power supply are R/C (AVLV2/AVLV8),
18 AWG, 90ºC. The suitability of the leads shall be determined in the end-use application.
8. The leakage current test was performed in accordance with the Ul1310 standard while the driver was connected to a 120 V and
also while connected to a 240 V source of supply and the maximum measured leakage current was 0.25 mA. Therefore, a
maximum of two LED Drivers can be used for portable signs.
9. The Output Cable is Listed, Power-Limited Circuit Cable (QPTZ), type PLTC, marked "sunlight resistant" or "sun res", “WET” or
“WET LOCATION”, 3 conductor, -40°C.
10.The minimum thickness of the aluminum of the housing of the drivers is 0.91 mm. This is in compliance with the minimum
required thickness that is specified in Table 6.1 of UL8750 standard for nonferrous sheet metal.
Power Supply with Class 2 output, models L24V100UNV-Q, and D24V100UNV-Q.
1. The drivers shall be installed in compliance with the applicable requirements of the end-product standard for, mounting, spacing,
casualty and segregation.
2. The maximum available output parameters were within the maximum allowable limits for Class 2, inherently limited as specified
in the
UL 1310, Standard for Class 2 Power Units for wet location and also in accordance with the Canadian Safety Standard
CSA C22.2 No. 223.
3. The drivers were tested for a maximum manufacturer’s recommended Tc location, should not exceed 67°C, in ambient of 40°C.
If adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be
conducted in the end use product.
4. The drivers are suitable for use in “DRY”, “DAMP”, and “WET” locations.
5. In the end product, spacings between transformers, ballast, nea power supplies, and LED power supplies shall be at least 25.4
mm (1 in.) from end to end and 101.6 mm (4 in.) from side to side. Minimum 25.4 (1 in.) spacing between thermoplastic, wood,
fiber or other combustible material and enclosed LED power supply when only one LED power supply is provided; and minimum
12.7 mm (0.50 in.) between thermoplastic, wood, fiber, or other combustible material and unenclosed LED power supply.
6. The input and output leads were not subjected to the strain relief test. However, the drivers are potted and the need to perform
the Strain Relief and/or Pushback Relief Tests on the lead wires should be determined in the end-use application.
7. The primary (Black/White/GREEN) and the output (Red-Black) connection wires of the power supply are R/C (AVLV2/AVLV8),
18 AWG, 90ºC. The suitability of the leads shall be determined in the end-use application.
8. The leakage current test was performed in accordance with the Ul1310 standard while the driver was connected to a 120 V and
also while connected to a 240 V source of supply and the maximum measured leakage current was 0.50 mA. Therefore, a
maximum of one LED Driver can be used for portable signs.
9. The Output Cable is Listed, Power-Limited Circuit Cable (QPTZ), type PLTC, marked "sunlight resistant" or "sun res", “WET” or
“WET LOCATION”, 3 conductor, -40 °C.
10. The minimum thickness of the aluminum of the housing of the drivers is 0.91 mm. This is in compliance with the minimum
required thickness that is specified in Table 6.1 of UL8750 standard for nonferrous sheet metal.
11. The “IP67” has not been evaluated by UL and should be considered in the end-use application.
VENTEX TECHNOLOGY INC
1201 JUPITER PARK DR
JUPITER, FL 33458
E319052
LED Lighting System, VenBrite, Consisting of Models VL-R100, VL-CW100, VL-W100, VL-x100, VL-x100N, VL-x100SC, VL-x200
Single LED Modules and Models VLP100-120, VLP100-277, VLP200-120, VLP200-277 LED Drivers. Provided with Low-Voltage
LED Wire Cat. Nos. VA-W09, VA-W02, VA-W00 and Wire Connector Part No VA-WN01, where x represents the color of the
LEDs (W, CW, WW, R, B, G, A, RO or any alphanumeric character). 1. The VL-x100 and VL-n100NS LED modules have been
evaluated for use with Ventex VLP100-120 and Ventex VLP100-277 power supplies. Suitability with any other power supply
shall be determined.
2. The VL-x200 LED modules have been evaluated for use with Ventex VLP200-120 and Ventex VLP200-277 power supplies.
Suitability with any other power supply shall be determined.
3. The LED lighting system is suitable for use in dry and damp locations. Consideration shall be given in the end product to the
Exclusion of Water Test.
4. These products may be installed in a sign body that is not enclosure rated. Wiring outside the sign body shall be in conduit or
equivalent wireway. Wiring provided between the power supplies and the LED modules within the sign body shall be R/C
163
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
(ZNPA2), Low-Voltage LED Wire, Manufactured by Ventex Technology Inc, Cat No VA-W09, VA-W02, and VA-W00, Rated
600V and 105C. All wire splices within the sign body shall be made using Listed wire connectors, Ventex Part No VA-WN01
(Manufactured by Ideal Industries Inc, Cat No 61), rated min 600V.
5. When wiring connections are not made with Ventex Part No VA-WN01 (Manufactured by Ideal Industries Inc, Cat No 61) wire
connectors, all splices shall be provided within an electrical enclosure and shall be provided with strain relief.
6. The LED driver input connection methods shall comply with the wiring requirements in UL48.
7. When provided, the power supply shall be suitably grounded through the grounding conductor and bonded through the metal
mounting tabs.
8. The power supply is intended for hard wiring only.
9. Components have been evaluated for a maximum temperature/density, per the following table:
Accessory Type
Density of
Accessory (#/in^3)
Model(s)
Max Temp of
component( C)
Min Rating of
plastic mount (°C)
LED Module
VL-x100, VL-x200
1/6
82.6
80
Power Supply
All
1/31
70.3
80
LED Module
VL-x100SC, VL-x100N
1/4
51
48
LED Module
VL-n100NS
1/4
55
60
Note: The suitability of any condition that would result in a more severe wattage density shall be determined in the product.
9a. Models VL-x100 have been evaluated for a maximum amount of LEDs, per the following table:
x - LED Color
Quantity of LEDs
W - White
120
CW - Cool White
120
WW - Warm White
120
R - Red
180
B - Blue
120
G - Green
120
A - Amber (Yellow)
120
RO - Red Orange
150
Any Alphanumeric Character
120
LEDs W, CW, and R shall have a maximum power dissipation of 1.33W and LEDs B, G, and A shall have a maximum power
dissipation of 0.7W.
9b. Models VL-x100SC, VL-x100N have been evaluated for a maximum amount of LEDs, per the following table:
x - LED Color
Quantity of LEDs
W - White
120
CW - Cool White
120
WW - Warm Whit
120
R - Red
150
B - Blue
120
G - Green
120
A - Amber (Yellow)
120
RO - Red Orange
150
Any Alphanumeric Character
120
10. Models VL-x200 have been evaluated for a maximum amount of LEDs, per the following table:
x - LED Color
Quantity of LEDs
W - White
70
CW - Cool White
70
WW - Warm White
70
R - Red
100
B - Blue
70
G - Green
70
A - Amber (Yellow)
70
RO - Red Orange
100
Any Alphanumeric Character
70
January 23, 2014
164
SIGN COMPONENTS MANUAL (SAM)
10a. Models VL-n100NS have been evaluated for a maximum amount of LEDs, per the following table:
n - LED Color
Quantity of LED Modules Quantity of LEDs
W - White
105
210
CW - Cool White
105
210
WW - Warm Whit
105
210
R - Red
135
270
B - Blue
105
210
G - Green
105
210
A - Amber (Yellow)
105
210
RO - Red Orange
135
270
Any Alphanumeric Character
105
210
11. LED Strings are intended to be series connected only. No parallel connections or interconnections of power supply circuits
shall be made.
12. The adhesive is suitable for securement to the following materials: Aluminum, Galvanized Steel, Stainless Steel, Enameled
Steel, Nickel Coated ABS, Glass (with or without Silane Coating), PVC, Glass/Epoxy, PBT, Polycarbonate, Acrylic/Polyurethane
Paint, Polyester Paint or Ceramic. For other materials where suitability of securement has not been determined, the adhesive
shall be submitted for evaluation or the LED module shall be secured by an additional suitable mechanical means.
13. LED model numbers may be followed with another suffix added to the end of the model number name. The suffix format will be
“-letter”. This suffix represents improved versions of LEDs whereby they exhibit a greater Efficacy (lumens/watt) than the original
LED. There would be no increase in heat dissipated or more energy used. The maximum forward voltages and current through
the LED would remain the same or be less than as stated in this report. For Example: Model VL-W100 may be provided with a
suffix such as VL-W100-b. Where the “-b” represents a brighter LED (126 lm/W compared to 100 lm/W) for the same power
dissipated)
LED drivers other than Class 2, Models VLP100D-U, VPL200D-U.
1. These LED Drivers comply with other than Class 2 output requirements.
2. These products are provided with the following electrical ratings:
Input
Output
Vac
Hz
A
Vdc
A
Model No.
VLP100D-U
100-277
50/60
0.5
400
0.125
VPL200D-U
100-277
50/60
.60
250
.250
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to
end, and 101.6 mm (4 in.) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products have been tested in an oven at max. 40ºC ambient.
7. These products are intended for use in dry or damp locations only.
8. The suitability of input/output leads and the wiring shall be determined in the end product use.
9. These products are constant current type that require the proper number of LED modules and controllers that do not exceed
the maximum output voltage.
10. These LED drivers are intended to be operated on a maximum 20 A branch circuit.
11. These LED drivers are intended for use in fixed equipment only.
VERSEIDAG-INDUTEX GMBH
INDUSTRISTRASSE 56
POSTFACH 2906
04150 KREFELD, GERMANY
E219382
Flexible sign face material, designated "Seemee IV".
1. Suitable for outdoor use.
2. Not suitable for use as an electrical enclosure.
3. Base color white.
4. Minimum thickness 0.015 in. (0.38 mm), minimum thickness 0.021 in. (0.53 mm) when secured with Recognized Component
ABC Sign Products tensioning systems.
5. Any dimension greater than 6 feet needs braces to prevent billowing.
6. Suitable for use with all Recognized Component Securement and Tensioning systems.
7. Securement and tensioning systems shall reliably secure the face to the sign and pull the face taut in all directions.
VINTECH INDUSTRIES
611 INDUSTRIAL PARK DR
IMLAY CITY, MI 48444
E318117
Aluminum Reinforced Thermoplastic Sign Trim Cap, Type Channel Trim.
1. Acceptable for use in wet locations.
2. Water exclusion must be determined in the end product.
3. Minimum 5 cm (2 in.) spacing from heat producing components required.
4. The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified adhesives
may be applied for the final bond.
Sign Face Generic Material
Solvent
Final Bond Adhesive
Sign Trim Generic
Material
165
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
Methyl Methacrylate (Acrylic)
Weld-On #4 or ( Methylene Chloride )
Weld-On #16, Weld-On #58
Cellulose Acetate
Butyrate
(Polycarbonate)
Weld-On #4 or Methylene Chloride
Weld-On #58, Lord Adhesive 7550 Cellulose Acetate
Butyrate
5. The sign trim and sign face assembly shall be secured to the sign body or sign enclosure.
VIRGINIA OPTOELECTRONICS INC
92 HONORS COURSE DR
LAS VEGAS, NV 89148 USA
E301137
Class 2 LEDs, Model ZLS-PCB-X Series, ZLS-PCBC-X Series and PL1-PMBC-X Series; where X can be any letter: R, Y, B, G or
W; ZLS-PMBC-T Series; where T may be C or RGB.
1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 15 V.
3. Class 2 LEDs Cat. ZLS-PCB-X Series, ZLS-PCBC-X Series, PL1-PMBC-X Series and ZLS-PMBC-T Series are each rated max.
3 watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the
secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules, Cat. Nos. 2LS-PCBC-WT, 2LS-PCBC-R, 2LS-PCS-R, 2LS-PCB-WT, 2LS-PMBC-RGB, 2LS-PMBC-C, PLPMBC-W, PL-PCBC-W, PL-PMBC-WT, PL1-PMBC-W, PL1-PMBC-WT.
1. These products are only suitable for connection to a Class 2 power source rated 15 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 15 V DC.
3. These products are each rated max. 7 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Modules, Cat. Nos ZLS-PYBT-XKA and PLQ-PYBT-XKA series, where Y and X maybe any alpha characters, A, T
and K may be blank or any alpha character and Q may be 1 or blank.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 24 V DC.
3. These products are each rated max. 7 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 LED Modules, Cat. Nos. ZLS-PPBC-Axx, ZLS-PPBC-Txx, ZLS-PPBC-Fxx, ZLS-PPBC-Bxx Series, where xx can be any
alpha characters or blank.
1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 12 V DC.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 LED Modules, Cat. No. ZLS-PPBC-TXXLY series, where XX can be replaced by any letters to represent a light color and
where Y is any number or blank.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC, 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than the electrical ratings.
3. These Class 2 LED modules are each rated as noted in the electrical ratings tables. When units are connected to a Class 2
circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at electrical ratings or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. The suitability of supply leads shall be determined in end use.
Power supplies, isolated Class 2, Models VO-12-20, VO-12-60.
1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
output.
2. These products are provided with the following electrical ratings:
Output
Model
Input Voltage
Input Current
Frequency
Output Voltage
Current
(mA)
Number
(V)
(A)
(Hz)
(Vdc)
VO-12-20
120-277
0.2-0.09
50/60
12
1660
January 23, 2014
166
SIGN COMPONENTS MANUAL (SAM)
VO-12-60
120-277
0.61/0.27
50/60
12
5000
3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end,
and 101.6 mm (4 in.) from side to side.
4. These products shall be enclosed in the end product.
5. These products are suitable for factory wiring only.
6. These products have been tested in oven at the noted ambient temperature with the following maximum case
temperatures, Tc:
a) For model VO-12-20 the Tc = 90ºC at max. ambient of 60ºC.
b) For model VO-12-60 the Tc = 82.2ºC at max. ambient of 40ºC.
8. These products are intended for use in dry or damp locations only.
9. The suitability of the input/output leads and wiring shall be determined in the end use product.
VISUAL LIGHTING TECHNOLOGIES
9 RANCHO CIR
LAKE FOREST, CA 92630
E352767
Class 2 Power Supply, Model HMLD-288-24SC-120.
1. These power supplies have been evaluated for use in portable LED signs.
2. The power supplies have outputs that individually comply with Class 2 circuit requirements.
3. These units are suitable for use in dry and damp locations without a need for an additional enclosure.
4. The output of this power source shall not be connected to any other power source or provide power to components connected to
another power source.
5. The attachment plug on the end of the power supply cord is not to be removed.
VYNEX SIGN SYSTEMS LTD
8175 WINSTON CHURCHILL BLVD
NORVAL ON CANADA L0P 1K0
E173052
Flexible sign face material, designated "Marquee", "Premier", "Premier 2000", and "Reflections" all w/ suffix numbers.
1. Suitable for outdoor use.
2. These products are not to be used as electrical enclosures.
3. These products are acceptable for use with all Recognized Component Sign Securement and Tensioning.
Marking - Company name or trademark Vyna-brite and model designation.
W R PABICH MANUFACTURING CO INC
2323 N KNOX AVE
CHICAGO, IL 60639-3415
E333077
Metal stitchers for sign channel letters, Models S13 and S25.
1. The tooling has been evaluated for joining only two pieces of painted or unpainted sheet metal using the #18 wire gauge for the
fabrication of the channel letters.
2. The electrical safety of these metal stitchers, have not been determined.
3. These S13 and S25 Series Metal Stitchers, use the BHMB clincher head for No. 18 wire gauge with various degrees of
hardness. It ranges from softest of 200, 230, 260, 280, 290, and up to 330 for being the most temper rating of the wire gauge.
4. Best results are obtained when joining the two pieces of painted or unpainted sheet metal with a total maximum thickness of
0.083 in. (2.11 mm.)
5. Minimum spacing between staples is 0.5 in. (12.7 mm) Maximum spacing between staples is 4 in. (101.6 mm).
6. All tooling shall be serviced and maintained in accordance with the manufacturers instructions. A service log shall be maintained
for each machine.
WAI CHI OPTO TECHNOLOGY LTD
6/F LIVEN HOUSE
63 KING YIP ST
KWUN TONG, HONG KONG
E364455
Class 2 LED modules, Cat. No. LXT01.
1. This product is only suitable for connection to a Class 2 power source, rated 24 Vdc.
2. This product has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and
energy limits and which is rated greater than electrical ratings.
3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. This product is suitable for use in dry and damp locations with supply sources rated at 24 Vdc.
5. The suitability of supply leads shall be determined in end use.
6. The mounting means shall be determined in end use.
WALT DISNEY IMAGINEERING
1401 FLOWER ST.
GLENDALE, CA 91221
Incandescent Outline Lighting, Cat. Nos. LTNG-XXXXXX where X denotes a number between 0 and 9.
1. The rim lighting units are acceptable use in dry, damp and wet locations.
2. The Rim Lighting System is not to exceed a string of sixty-six lights.
3. Make sure that each connector is inserted fully into the lampholder base.
4. Each lampholder is to be secured by screws through the holes provided on lampholder base.
E235817
167
5.
6.
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
This rim lighting system is only acceptable for use with maximum 6 Watt, Type 6S6/BB with brass base light bulbs.
When installed in a wet location, each light bulb is to be fitted with a thermoplastic lamp gasket part no. SK124 over the base
of the glass envelope.
WATCHFIRE SIGNS BY TIME-O-MATIC INC
1015 MAPLE ST.
PO BOX 850
DANVILLE, IL 61832
E350856
Gas price sign module, designated PXY, where "X" is any character indicating LED color and "Y" is 12, 18, or 24 indicating
height. May be provided with additional suffixes.
1. Suitable for use in an outdoor, wet location when conduit used. Otherwise, front of sign suitable for use in an outdoor, wet
locations and the rest suitable for dry and damp locations. The sides and back need to be installed within a suitable wet location
enclosure.
2. Provided with conduit knock-outs which are suitable for permanent connection to module. Ground wire needs to be connected to
power supply ground.
3. The gas price module is constructed as a complete electrical enclosure for damp location use.
4. A suitable branch circuit protective device not exceeding 20 A shall be provided in the end-product.
5. Sign provided with drain holes and ventilation slot in the front of the enclosure. Openings shall not be obstructed.
6. Any splices need to be made in an electrical enclosure outside the equipment.
WESTRIM PRODUCTS
2268 FAIRVIEW BLVD
PO BOX 300
FAIRVIEW, TN 37062
E209062
Special Use Switch with boot, Model No. 38057.
1. This device is intended for use in outdoor applications where the boot is protected from inadvertent abuse.
2. The special use switch mounting hole and mounting surface shall be free from burrs and have a close tolerance to the diameter
of the switch mounting collar.
3. The special use switch shall be locked in place by a lockwasher or other means to prevent rotation.
4. The special use switch shall be provided with a means of indicating the on and off positions in accordance with UL 48, the
Standard for Electric Signs.
5. The special use switch is to be used within its electrical rating in accordance with UL 48, the Standard for Electric Signs.
6. The Water Exclusion Test shall be conducted as a regular part of each inspection.
WESTRIM PRODUCTS
2268 FAIRVIEW BLVD
PO BOX 300
FAIRVIEW, TN 37062
E330428
Electrode Receptacle Insulators, Model Nos. GH100, GH200, GH200P.
1. Must be enclosed in end product.
2. These receptacles are intended for use in dry , damp and wet locations. In wet locations, unless provided with a R/C receptacle
cover that prevents to the entry of precipitation, the receptacles when mounted in a raceway are to comply with the following:
A)The raceway is required to have drain openings, and
B)The receptacles are to be located such that no live parts are
located below the inside end of the receptacle.
3. Water exclusion must be determined in the end product.
4. These receptacles are rated for maximum 15 kV, 7.5 kV to ground.
Electrode Receptacle Insulators, Model Nos. GH300, GH300P.
1. Must be enclosed in end product.
2. These receptacles are intended for use in dry, damp and wet locations. In wet locations, unless provided with a R/C receptacle
cover that prevents to the entry of precipitation, the receptacles when mounted in a raceway are to comply with the following:
A)The raceway is required to have drain openings, and
B)The receptacles are to be located such that no live parts are located below the inside end of the receptacle.
3. Water exclusion must be determined in the end product.
4. These receptacles are rated for maximum 15 kV, 7.5 kV to ground.
WHITE LIGHTNING FIXTURES LTD
SUITE 1201
TOWER 2, THE GATEWAY
25 CANTON RD, TSIM SHA TSUI
KOWLOON, HONG KONG
E350640
LED Kit, designated LB, WW or FL followed by suffixes YY, ZZ, LLL, AAA, DD, EEE, FF as indicated below.
1. The LED light strips are only suitable for connection to a Class 2 power source, rated 30 Volt DC or 15 Volt AC or less.
2. The LED light strips have not been evaluated for use when connected to a power source that does not comply with Class 2
voltage and energy limits and which is rated greater than 30 Volt DC or 15 Volt AC.
3. These Class 2 LED modules are rated as noted below.
Model
LED Strip Max Length In.
Voltage (DC)
Current (ma)
Power (Watts/foot)
LB
120
24
10-500
0.5-2
January 23, 2014
168
SIGN COMPONENTS MANUAL (SAM)
WW
120
24
10-500
3.5-8
FL
120
24
10-500
12-25
When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating
of the Class 2 supply.
4. The LED light strips are suitable for use in dry, damp and wet locations with supply sources rated class 2.
5. All sizes may be cut every six inches except the 5 in. size may be cut every 1 in on the 12 LED / Ft models. All sizes may be cut
every 4.8 inches except the 4 in. size may be cut every 0.8 in on the 15 LED / Ft models.
6. The suitability of the electrical box provided for LED driver mounting shall be evaluated. The following shall be considered:
metal thickness, ability to exclude water when identified for outdoor use, drain holes, driver mounting, grounding, provision for
power supply connections, and enclosure of LED driver line voltage lead wires.
7. LED drivers shall be installed in an electrical enclosure. When more than one LED driver is installed in electrical enclosure, the
drivers shall be spaced at least 1 inch apart end to end and 4 inch apart in other directions.
8. LED drivers shall be installed in accordance with the installation instructions provided with LED driver and the nameplate
markings.
9. The outdoor LED driver electrical box shall be installed in accordance with the instructions and markings provided with the
electrical box. Instructions are not required for electrical boxes mounted indoors.
LED module, designated Class 2 Light Engine, Models LLL-AAA-DD-CC-MM-X-Y-Z as indicated below.
1. These products are only suitable for connection to a UL R/C (FKSZ2) or {UYMR2) Class 2 power source, rated 30 Volt DC or 15
Volts AC or less. The products have not been evaluated for use when connected to a power source that does not comply with
Class 2 voltage and power limits.
2. When the LED Array modules are connected and used with power supplies other than Class 2, the need for an additional
evaluation shall be considered in the end use product investigation.
3. The Array modules shall be installed in compliance with the mounting, Spacing, casualty, and the segregation requirements
applicable to the ultimate application.
4. This LED Module is suitable for use in dry, and damp locations with Supply source rated Class 2.
5. The LED modules come in various lengths and not designed for cutting.
6. The suitability of the LED Array to be used without an enclosure shall be determined in the end-use application.
7. Supply connection shall be determined in the end used application.
8. Temperature, abnormal fault and the need for conducting Dielectric-Withstanding test shall be determined in the end used
application.
9. The suitability of the electrical box provided for LED driver mounting shall be evaluated. The following shall be considered:
metal thickness, ability to exclude water when identified for outdoor use, drain holes, driver mounting, grounding, provision for
power supply connections, and enclosure of LED driver line voltage lead wires.
10. LED drivers shall be installed in an electrical enclosure. When more than one LED driver is installed in electrical enclosure,
the drivers shall be spaced at least 1 inch apart end to end and 4 inch apart in other directions.
11. LED drivers shall be installed in accordance with the installation instructions provided with LED driver and the nameplate
markings.
12. The outdoor LED driver electrical box shall be installed in accordance with the instructions and markings provided with the
electrical box. Instructions are not required for electrical boxes mounted indoors.
YAHAM OPTOELECTRONICS CO LTD
HAN`S INDUSTRIAL PARK
NO 128 CHONG QING RD
FUYONG BAOAN DISTRICT
SHENZHEN, GUANGDONG 518103 CHINA
E330631
LED Cabinet Panels, Cat. Nos. YH-T10-1R1PG1B, YH-D16-1R1PG1B.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These devices are to be used in accordance with the ratings and load types as specified below.
Catalog Number
Max. Operating Voltage, Current and Power
Input (V)
YH-D16-1r1PG1B
Input Current (A)
Type Load
Input Power (Watts)
100-240
4
600
LED
YH-T10-1R1PG1B 100-240
4
300
LED
3. The suitability of supply connections shall be considered in the end product.
4. Grounding should be in accordance with the end product requirements.
5. These products are intended to be permanently connected to a source of supply.
6. The Rain Test was conducted on the entire product. However, in an end product application where many panels are connected
together, the Exclusion of Water Test should be conducted.
7. These power supplies are intended for connection to a maximum 20 Amp branch circuit.
8. These panels are only suitable for being coupled together in an overall sign and are not suitable for being interconnected in the
field.
LED Cabinet Panels, Cat. No. YH-UL-XZT; where X and Z may be alphanumeric characters, and T may be alphanumeric
characters or blank.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These devices are to be used in accordance with the ratings and
load types as specified below.
Catalog Number
Max. Operating Voltage, Current and Power
Input (V)
Input Current (A)
Input Power
(Watts)
Type Load
169
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
YH-UL-T4
100-240
4
600
LED
YH-UL-D25
100-240
1
300
LED
3. The suitability of the supply connections shall be considered in the end product.
4. The need for the Ground Continuity Test and Leakage Current Test shall be determined in the end product.
5. The Exclusion of Water Test was conducted on the entire product. The need to conduct the Exclusion of Water Test in the end
product shall be considered on the supply connection part of the product.
YESCO LLC
5119 S CAMERON ST
LAS VEGAS, NV
89118
E138960
Class 2 LED Light Strings, Cat. No. FL Series.
1. These products are only suitable for connection to a UL Listed or Recognized Class 2 supply. If intended for Wet Locations, the
power supply or transformer shall have an output of 12 volts.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited supplies.
3. When connected to a Class 2 circuit, the lighting string shall be sized appropriately so as to not exceed the output current and
power rating of the Class 2 supply.
4. The light strings, when connected to a Class 2, 12 Volt output supply, are suitable for installation in wet, damp and dry
locations. The light strings, when connected to Class 2, 24 Volt output supply, are suitable for installation in damp and dry
locations only.
Decoder driver, Model YDD-128.
1. The need for an overall enclosure shall be determined in the end-use application.
2. The suitability of the mounting means shall be determined in the end-use application.
3. The need for a Temperature Test shall be determined in the end-use application. The connectors are not acceptable for field
connections and are only intended for factory installation to mating connectors of the end-use product.
Sign flasher, Cat. No. YM-X where X is any number 1 to 6 incl.
1. The component shall be installed in compliance with the enclosure, mounting, creepage, clearance, casualty markings, and
segregation requirements of the end-use application.
2. The terminal block and input/output connectors telephone jacks are not acceptable for field connections and are only intended
for connection to mating connectors of internal wiring inside the end-use product. The acceptability of these and mating
connectors relative to secureness, insulating materials, and temperature shall be considered in the end-use product.
3. A temperature test shall be conducted in the end-use product. The acceptability of the temperature reading or the following
components shall be evaluated: Internal Wiring; PWB; Terminal Block, Max. 105°C; Transformer, Max. 90°C; Triac, Max.
100°C.
Sign Flasher, Model P. N.YFLASHAC.
1. This flasher is suitable for use when installed in a metal enclosure that is at least 12 by 12 by 3 inches having two 4 square inch
openings on the side with a minimum 55 cfm fan mounted on the bottom.
2. Where more than one flasher is installed within an enclosure, each unit shall be located so that no part of each flasher is within 4
inches of each other. The enclosure shall be sized to provide at least 2 inches to sidewall and top and at least one or more fans
provided that produces a cfm of a least 25 cfm per flasher.
3. No other components such as neon transformers or fluorescent ballasts shall be located within the enclosure with this flasher.
4. This component is suitable for use in dry and damp locations. In damp locations, the unit must either be located at least 1/2
inches from bottom of enclosure and the bottom of the enclosure provided with drain holes or the unit installed within an
enclosure that is gasketed to prevent the entrance of water into the compartment.
5. This flasher is suitable for use on a 120 V, 60 Hz service and is rated for 0.25 amp input. It is capable of switching up to six 20
amp branch circuits each having maximum 16 amp load.
6. This component is to be installed and wired in the at end product manufacturer's location as the connectors are not suitable for
field installation.
Changing Message Sign Transformer Assembly, Models YACDC1.5, YACDC3.3, YACDC750 may or may not be followed by
X10 and LED Module "Sign Face" (LED Message Center), Model LEDMC.
1. Wiring and means of connection between modules shall be investigated in the end product requirements.
2. For models YACDC1.5, YACDC3.3 and YACDC750No no tests have been conducted on this component so consideration
should be given to conduct input test, the normal temperature, dielectric voltage withstand components abnormal and rain tests
in the end product changing message sign.
3. These components are not provided with suitable enclosure or sign body. The need for a electrical enclosure should be
considered in the end product.
4. Transformer spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 2 inches.
5. Transformer spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and
top of enclosure is kept at minimum 6 inches.
LED Disc Lamp, Model YPAR38LED-X series, where X can be replaced by A or R.
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These Lamps are suitable for use in wet locations.
3. These units unit has not been tested for use in totally enclosed recessed fixtures.
4. These units are not intended for use with emergency exit fixtures or emergency exit lights.
5. The base portion of lamp enclosure is not exposed to sunlight. Only the enclosure with the LEDs is to acceptable to be exposed
to the weather.
Cold Cathode Self Ballast Lamp, Models "Cold Cathode Self Ballast Lamp" unit.
1. These components should be installed in accordance with the manufacturer's instructions.
2. These units are not intended for use with emergency exit fixtures or emergency exit lights.
Class 2 LED Light Strings, Designated: Smart Strip XX Series, where XX may be any alphanumeric characters.
January 23, 2014
170
SIGN COMPONENTS MANUAL (SAM)
1. These Class 2 LED modules are only suitable for connection to a Class 2 power source, rated 15 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. These Class 2 LED modules are rated max. 7 Watts per LED module. When these units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volts or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
Class 2 LED Modules Designated Smart LED.
1. This component shall be installed in accordance with the manufacturer’s installation instructions.
2. This component is only suitable for use in dry locations.
3. This component is to be connected to a Class 2 power source
Class 2 LED Modules Designated as "Smart Puck".
1. These products are only suitable for connection to a Class 2 power source rated 27 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limited circuit and which is rated greater than 27 V DC.
3. These products are each rated max. 27 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 27 Volts DC or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
be considered.
Class 2 Powered LED Lamp, Designated "YESCO Globe Lamp".
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits.
3. These products Class 2 LED modules are rated max. 22 Watts. When these units are connected to a Class 2 circuit, they are
not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 12 Volts or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
LED Driver Power Supply Box with Driver - I, Power Supply Box with Driver - II
1. The output of power supplies used of these units have been evaluated to Class 2 output requirements for dc circuits.
2. These products are suitable for use in dry locations only.
3. In the end product, the spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
4. The suitability of strain relief, current leakage and grounding tests shall be determined in the end-use product.
Fiber Illuminator Model No. YESCO Fiberoptic Illuminator
1. These products are suitable for Indoor use only.
2. The temperature test was conducted in a metal box with overall dimensions of 24 by 10 by 18 inch, in the end product, the
spacing to other heat producing components shall be minimum 9 inches spacing to sidewalls; minimum 3 inches spacing to front
and back walls, and minimum 14 inches spacing to top of enclosure.
3. Only the Input, Normal Temperature, Dielectric Voltage Withstand and Abnormal tests were conducted.
4. The wiring connection and mounting means were not evaluated and should be considered in the product.
5. The Ground Continuity and Strain Relief Tests were not conducted and needs to be conducted In the end product.
6. This product needs to be enclosed in the end product.
LED Changing Message Sign Computer designated as TF-TKS-G20-8310-00X-AT Series, where X is 5, 6, 7 or 8.
1. These components should be installed in accordance with the manufacturer's installation instructions.
2. In the end product, the spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and
minimum 2 inches spacing to top of enclosure.
3. These products are suitable for use in dry locations.
4. These products are rated as the following:
Model Designation
TF-TKS-G20-8310-00X-AT Series
Input Voltage (Vac)
Input Current (A)
Input Frequency
(Hz)
100-240
2
50-60
Indoor Polymeric Sign Body Material, designated as "LED Housing".
1. These products are polymeric non-enclosure rated sign body material for use in dry locations. The materials are only suitable to
house LED module strips that are powered by UL Listed or Recognized Class 2 power supplies rated max 30 VDC or max 30
VAC.
2. These products are not suitable for use as electrical enclosures.
3. These products shall be provided with mounting instructions.
4. These products are only suitable for indoor use.
Sign component, designated as "LCD SCREEN BOARD".
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are suitable for use in dry and damp locations.
3. These products shall be enclosed in a suitable electric enclosure in the end product.
4. These products have the following electrical ratings:
Model
Max Input Voltage (V)
Max Input Current (A)
Frequency (Hz)
LCD Screen Board
120
8.6
60
5. These units were tested in open air room ambient temperature with the fans operating continuously. Therefore, these units shall
be subjected to a temperature test in the end product.
6. The need to conduct ground continuity tests shall be determined in the end product.
Sign component, designated as “LED Module".
171
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are suitable for use in dry location.
3. These products shall be enclosed in a suitable electric enclosure in the end product.
4. These products have the following electrical ratings:
Model
Max Input Voltage
Max Input Current
Max Input Power
Frequency
(V)
(A)
(W)
(Hz)
“LED Module"
120
1
110
60
5. These units were tested in open air room ambient temperature with the fans operating continuously. Therefore, these units shall
be subjected to a temperature test in the end product.
6. The need to conduct ground continuity tests shall be determined in the end product.
LED controllers, designated as "Shelves System".
1. These components should be installed in accordance with the manufacturer’s instructions.
2. These products are suitable for use in dry and damp locations.
3. These products are provided with the following electrical ratings:
Model
Max Input Voltage
Max Input Current
Frequency
(V)
(A)
(Hz)
Class 2 LED Controllers, designed as “Shelves
120
1
60
System”
4. The need to conduct a ground continuity test shall be considered in the end product.
5. All the circuitry connected to the output of the power supply are Class 2.
6. These products shall be enclosed in the end product.
7. These products are intended for connection to a dedicated receptacle inside permanently installed signs. The need for a leakage
current test shall be considered in the end product if used in a cord connected sign or other cord-connected end products.
YUYANG DNU CO LTD
488-1 YURAM-LI
PALTAN-MYEON
HWASEONG-SI, GYEONGGI-DO 445-910 REPUBLIC OF KOREA
E342333
Class 2 LED Modules,YY3232S-4S-X Series and YY-RX16-S3.
1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less.
2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
and energy limits and which is rated greater than 15 V.
3. These Class 2 LED modules are each rated as noted in the model list tables. When units are connected to a Class 2 circuit, they
are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Vdc or less.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. Modules can be installed to interconnect leads in the field or pre-installed.
ZHANGJIAGANG FEITENG ALUMINIUM COMPOSITE PANEL CO LTD
HOUCHENG INDUSTRIAL DEVELOPMENT ZONE
JINGANG TOWN
ZHANGJIAGANG, JIANGSU 215631 CHINA
E350268
Structural panel, Model Aluminum composite panel.
1. Suitable for use in dry, damp and wet locations.
2. Suitable for use in decorative and sign body applications only.
3. Suitable for use in component support applications. When threaded directly into the panels, suitability of screws shall be
determined in the end product.
4. Rain tightness shall be determined in the end product.
5. Electrical spacings and bonding for grounding shall comply with the end product standard.
6. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a
point of support.
7. These materials are rated Polyethylene. Consideration will need to be given to end product thermal spacings from heat
producing components or temperature test.
8. These materials are available as unpainted aluminum or pre-painted aluminum.
9. This material has not been investigated for the securement of conduit, electrode housings or the like, suitability shall be
determined in the end product.
ZHEJIANG DOT LIGHTING CO LTD
768 ANCHANG WEST RD
KEQIAO ECONOMY DEVELOPMENT DISTRICT
SHAOXING, ZHEJIANG 312081 CHINA
E349849
LED Class 2 Modules, Cat. Nos. MOD3528-3-1, MOD5630-6-1, MOD5630-6-2, MOD5630-8-1.
1. These LED modules are each rated as noted in the electrical ratings tables. Input test for each LED module should be
considered in end products.
2. The suitability of the electrical construction shall be determined in the end use.
3. The suitability of the mounting means shall be determined in the end use.
4. PWB is metal based, rated V-0, 130 C. Temperature testing shall be conducted in the end product.
5. Suitability for use in environmental locations shall be considered in the end product.
ZLIGHT TECHNOLOGY LLC
E338098
January 23, 2014
172
SIGN COMPONENTS MANUAL (SAM)
1013 HARIMAW CT E
METAIRIE, LA 70001
LED Class 2 Modules Models Z-ECO, Z-M2 and Z-ULTRA. May be followed by xxx-yyy where xxx-yyy may be any alphanumeric
characters to indicate LED Color and other non-critical options for marketing purpose.
1. These products are only suitable for connection to a Class 2 power source rated 12V dc or less. When units are connected to a
Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.
2. These products are suitable for use in dry and damp locations with supply sources rated at 12V dc or less.
ZUNI SCROLLING SIGNS LLC
2011 4TH AVE
SPRING LAKE, NJ 07762
E362393
Class 2 LED Modules, designated as LEDBL-XX Series, where XX may be replaced with ES, STD or HP.
1. These products are only suitable for connection to a Class 2 power source rated 24 Volt DC or less.
2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
limited circuit.
3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
rating of the Class 2 supply.
4. These products are suitable for use in dry, damp and wet locations.
5. These products are not required to be enclosed or protected from the weather in the end product.
6. These products may be secured in place in the end product by any means available.
Class 2 Scrolling System, Model SPDE-XXAY kit, where XX may be 51 or 76; and Y may be X or E.
1. These products are only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated
maximum 24 VDC.
2. These products are rated per the Table below. When the units are connected to the Class 2 supply, their loads are to be limited
to draw a total power or current of no greater than the output power or current rating of the Class 2 power supply.
Max. Input Class 2
Each Output – Class 2
Number of
Vdc
Max. Vdc
Max. VA
Model
Outputs
SPDE-XXAY kit 24
24
12
2
3. These products are suitable for use in dry and damp locations.
4. These drivers are provided with a maximum of 2, Class 2 outputs.
5. These products are suitable for factory wiring only.
6. These products shall be enclosed in the end product.
SIGN COMPONENTS CLASSIFIED FOR USE WITH SPECIFIED EQUIPMENT
(UYTA)
This category covers specific components that are Classified for use with components manufactured by others, such as:
Listed GTO cable surface marked "Integral Sleeve" that is also Classified for use with specific Listed or Recognized Component
neon electrode boots; and Listed or Recognized Component neon electrode boots that are also Classified for use with specific
Listed GTO cable surface marked "Integral Sleeve."
The combination of the integral sleeve and the specified neon electrode boots identified under this Classification has been
evaluated and found to comply with the enclosure requirements for:
a) the splice between neon tubing electrode leads and GTO cable, and
b) the GTO cable leading to the splice.
These products are provided with installation instructions that define the scope of the system and method of installation.
TECNOLUX INC
103 14TH ST
BROOKLYN, NY 11215
E252991
GTO cable with integral sleeve, Neon electrode enclosures Model Nos. xxSC1y, where xx is 10, 12, 15, or 18 and y (optional) is
B, G or W manufactured by Tecnolux Inc. Classified for use with GTO cable with integral sleeve Cat. No. GTO15 (14 thru 18AWG)
and GTO10 (18AWG) with Integral Sleeving manufactured by Silitherm S.R.L. Suitable for dry and damp locations with the
different models accommodating the electrodes diameters as follows: 10SC1y - 10 mm; 12SC1y - 12-13mm; 15SC1y - 15-16mm;
18SC1y - 18-19mm.
GTO cable with integral sleeve, Neon electrode enclosures Model Nos. xxSC1yDB, where xx is 10, 12, 15, or 18 and y (optional)
is B, G or W manufactured by Tecnolux Inc. Classified for use with GTO cable with integral sleeve Cat. No. GTO15 (14 thru
18AWG) and GTO10 (18AWG) with Integral Sleeving manufactured by Silitherm S.R.L. Suitable for dry and damp locations.
TRANSCO TO GO LLC
1059 COLITE DR
WEST COLUMBIA, SC 29170
E247018
GTO cable with integral sleeve, Cat. No. Cat. No. GTO-10 with Integral Sleeving manufactured by Transco To Go LLC.
Classified for use with neon electrode boots Part Nos. SS0, EC0, SS3 and EC3. manufactured by Electrobits International. GTO
cable with integral sleeve GTO-15 with Integral Sleeving manufactured by Transco To Go LLC. Classified for use with neon
electrode boots Part Nos. SSW3, ECW3, SSW5, ECW5, SSW6 and ECW6 manufactured by Electrobits International.
GTO cable with integral sleeve, Cat. No. GTO-10 and GTO-15 (14 thru 18AWG) with Integral Sleeving manufactured by Transco
To Go LLC. Classified for use with Polymeric Neon Electrode Enclosures, Series Short Sleeve SS10mm30mA, SS12mm60mA,
SS13mm60mA or SS15mm60mA and Series End Cap, EC10mm30mA, EC12mm60mA, EC13mm60mA or EC15mm60mA in
173
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
combination with GTO Cable Sleeving Adaptor GTOCA260 manufactured by Electrobits International, Inc.
GTO cable with integral sleeve, GTO-15 (14 thru 18AWG) with Integral Sleeving manufactured by Transco To Go LLC.
Classified for use with Polymeric Neon Electrode Enclosures, Series Short Sleeve xxSC1y, where xx is 10 or 12 and y (optional) is
B or W, and Series End Cap, xxSC1yDB, where xx is 10, 12 or 15 and y(optional) is B or W, manufactured by Technolux Inc.
GTO cable with integral sleeve, GTO-10 (14 thru 18AWG) with Integral Sleeving manufactured by Transco To Go LLC.
Classified for use with Polymeric Neon Electrode Enclosures, Series Short Sleeve xxSC1y, where xx is 10 and y (optional) is B or
W, and Series End Cap, xxSC1yDB, where xx is 10, 12 or 15 and y(optional) is B or W, manufactured by Technolux Inc.
GTO cable with integral sleeve, Cat. Nos. GTO-15 (14-18AWG) with Integral Sleeving manufactured by Transco To Go LLC.
Classified for use with neon electrode boots Part Nos. ECS 7-10, ECS 7-12, ECS 7-13, ECS 7-15, ECDB 7-10, ECDB 7-12, ECDB
7-13 and ECDB 7-15 manufactured by Transco To Go LLC.
GTO cable with integral sleeve, GTO-15 (14AWG) with Integral Sleeving manufactured by Transco To Go LLC. Classified for use
with neon electrode boots Part Nos. ESC 8-10, ECS 8-12, ECS 8-13, ECS 8-15, ECDB 8-10, ECDB 8-12, ECDB 8-13 and ECDB
8-15 manufactured by Transco To Go LLC.
GTO cable with integral sleeve, GTO-10 (18AWG) with Integral Sleeving manufactured by Transco To Go LLC. Classified for use
with neon electrode boots Part Nos. ECS 7-10, ECS 7-12, ECS 7-13, ECS 7-15, ECDB 7-10, ECDB 7-12, ECDB 7-13 and ECDB
7-15 manufactured by Transco To Go LLC.
GTO cable with integral sleeve, GTO-10 (14-18AWG) with Integral Sleeving manufactured by Silitherm S.R.L. Classified for use
with neon electrode boots Part No. ECDB 7-13 manufactured by Transco To Go LLC.
GTO cable with integral sleeve, Cat. Nos. GTO-15 (14-18AWG) with Integral Sleeving manufactured by Silitherm S.R.L.
Classified for use with neon electrode boots Part Nos. ECDB 7-10, ECDB 7-13 and ECDB 7-15 manufactured by Transco To Go
LLC.
GTO cable with integral sleeve, Cat. Nos. GTO-10 (18AWG min.) with Integral Sleeving manufactured by Silitherm S.R.L.
Classified for use with neon electrode boots, Part No. ECS 7-13 manufactured by Transco To Go LLC.
GTO cable with integral sleeve, Cat. Nos. GTO-15 (18AWG min.) with Integral Sleeving manufactured by Silitherm S.R.L.
Classified for use with neon electrode boots, Part Nos. ECS 7-10, ECS 7-13 and ECS 7-15 manufactured by Transco To Go LLC.
GTO cable with integral sleeve, Cat. No. GTO-15 (18AWG - 14AWG) with Integral Sleeving manufactured by Paige Electric Co L
P. Classified for use with neon electrode boots Part Nos. ECS 7-10, ESC 7-13, ECS 7-15, ECDB 7-10, ECDB 7-13, ECDB 7-15
manufactured by Transco To Go LLC.
GTO cable with integral sleeve, Cat. No. GTO-10 (18AWG) with Integral Sleeving manufactured by Paige Electric Co L P.
Classified for use with neon electrode boots Part Nos. ECS 7-10, ECS 7-13, ECS 7-15, ECDB 7-10, ECDB 7-13, ECDB 7-15
manufactured by Transco To Go LLC.
SIGN FLASHERS (UYZZ2)
NEMCO CONTROLS INC
10306 SAGELINK CT
HOUSTON TX 77089
E161347
Electronic sign flasher, Model 2P-NX.
1. These devices must be used within a suitable enclosure.
2. These devices are rated 120 Vac, 600W for incandescent loads only.
Electronic Sign Flasher, Model Nos. 3P4 followed by: 1 on 3 off-120V-8A, 1 on 2 off-120V-8A, 1 on 2 off-24V-8A, 1 on 3 off-24V8A, 1 on 2 off-24V-20A, or 1 on 3 off-24V-20A.
1. These devices must be used within a suitable enclosure.
2. These devices have only been investigated for load types as specified below.
Output Current
(Amps max. per
AC Input
Input
Voltage
Current
circuit Tungsten
Model Number
3P4 (Volts)
(Amps)
Load only)
1 on 3 off-120V-8A
120
8
8
1 on 2 off-120V-8A
120
8
8
1 on 2 off-24V-8A
24
8
8
1 on 3 off-24V-8A
24
8
8
1 on 2 off-24V-20A
24
20
20
1 on 3 off-24V-20A
24
20
20
3. These devices must be surface mounted to an aluminum plate having a minimum 1/16 in. thickness with a 96.5 square inch
surface area or the following measurements 10-7/8 by 8-7/8 in. or larger.
Electronic Sign Flasher, SLAVE-24V-20A and SLAVE-120V-20A.
1. These devices must be used within a suitable enclosure.
2. These devices have only been investigated for load types as specified below.
Output Current
AC Input
Input
(Amps max. per
Model Number
Voltage
Current
circuit Tungsten
(Volts)
(Amps)
Load only)
24V-SLAVE-20A
24
20
20
120V-SLAVE-20A
120
20
20
3. These devices must be surface mounted to an aluminum plate having a minimum 1/16 in. thickness with a 96.5 square inch
surface area or the following measurements 10-7/8 by 8-7/8 in. or larger.
4. The SLAVE units are only suitable for use with NEMCO Model 3P4 Series controllers.
SWITCHES, PHOTOELECTRIC (WJCT2)
January 23, 2014
174
SIGN COMPONENTS MANUAL (SAM)
PRECISION MULTIPLE CONTROLS INC
33 GREENWOOD AVE
MIDLAND PARK, NJ
07432
E36102
Photoelectric switches, Models A105, A305 may be followed by suffix "BP".
1. Maximum load rating 8.3 A tungsten, 5 A ballast, 120 Vac.
2. Shall be reliably mounted within a suitable enclosure with lens protruding through a gasketed opening.
Coated Electrical Sleeving (UZFT2)
Consideration is to be given to the following Conditions of Acceptability when these components are employed in the end-use
equipment:
1. Sleeving shall not be used over the maximum voltage rating.
2. Sleeving shall not be used over the maximum temperature rating.
3. Sleeving is not acceptable for use in contact with sharp edges, corners, projections or burrs, or where subjected to tension,
compression, abrasion or repeated flexing without additional testing.
4. Sleeving is not recommended for use where it is feasible to employ a standard insulated conductor (appliance wiring material)
intended for the purpose.
5. Sleeving shall be used in dry and damp locations only as defined in ANSI/NFPA 70, "National Electrical Code."
SPECIAL USE SWITCH (WOYR2)
1. Switch body shall be enclosed within suitable enclosure. Switches in outdoor signs shall be enclosed within Listed
weatherproof enclosures or shall have drain holes in the separate enclosure that acts as an accessibility barrier.
2. HP rated switch is current rated as follows:
Extruded Insulating Tubing (YDPU2)
Consideration is to be given to the following Conditions of Acceptability when these components are employed in the end-use
equipment:
1. Tubing shall not be used where it is feasible to employ a standard insulating conductor (e.g., appliance wiring material) intended
specifically for the purpose.
2. Unless indicated in the individual Recognitions, the tubing has not been investigated for use in contact with sharp edges,
corners, projections or burrs , or where subject to tension, compression, abrasion, repeated flexing or where exposed to ultraviolet
radiation or oil contamination .
3. Tubing shall be used in dry and damp locations only as defined in ANSI/NFPA 70, "National Electrical Code."
4. The minimum wall thickness and the published ratings of the tube shall be considered in the end-product investigation.
5. The tubing has not been investigated with respect to its resistance to ignition from electrical sources.
MECHANICAL PROTECTION
TUBING (YDRQ2)
1. Suitable for use as mechanical protection of insulation on low-voltage wiring.
2. Surfaces likely to bear against these materials must be free of burrs and sharp edges.
WIRE POSITIONING DEVICES
(ZODZ2)
175
SIGN COMPONENTS MANUAL (SAM)
January 23, 2014
1. Refer to UL’s Recognized Component Directory for Conditions of Use.
2. Not suitable for use where exposed outdoors.
3. All materials that are rated less than 90 C shall be located not less than 1 in. from heat producing components.
January 23, 2014
FILE NUMBER INDEX
E10092, pg. 2
E101623, pg. 7
E109022, pg. 73
E122656, pg. 2
E125271, pg. 48
E129809, pg. 155
E131602, pg. 46
E136722, pg. 139
E136850, pg. 143
E138960, pg. 169
E145519, pg. 3
E146154, pg. 26
E152309, pg. 47
E161347, pg. 173
E163602, pg. 143
E16382, pg. 60
E164925, pg. 4
E173052, pg. 166
E175045, pg. 41
E176781, pg. 7
E180252, pg. 111
E187585, pg. 3
E188273, pg. 132
E192264, pg. 152
E204188, pg. 6
E205267, pg. 5
E209062, pg. 167
E210026, pg. 21
E211810, pg. 125
E211963, pg. 34
E213411, pg. 121
E215393, pg. 145
E215616, pg. 5
E219167, pg. 55
E219382, pg. 164
E220096, pg. 112
E220165, pg. 126
E221730, pg. 28
E223028, pg. 73
E225580, pg. 82
E225855, pg. 97
E226833, pg. 158
E227355, pg. 65
E228165, pg. 33
E230262, pg. 99
E230358, pg. 35
E232462, pg. 42
E232725, pg. 93
E235322, pg. 84
E235719, pg. 106
E235817, pg. 166
E237417, pg. 44
E238096, pg. 65
E239418, pg. 50
E242292, pg. 110
E242758, pg. 100
E242790, pg. 54
E242985, pg. 140
E243613, pg. 6
E245307, pg. 154
E247018, pg. 172
E248791, pg. 153
E249377, pg. 70
E250835, pg. 6
E251622, pg. 18
E252578, pg. 108
E252627, pg. 136
E252991, pg. 172
E255447, pg. 16
E255480, pg. 88
E257157, pg. 6
E257980, pg. 72
176
SIGN COMPONENTS MANUAL (SAM)
E258264, pg. 112
E258512, pg. 73
E29252, pg. 66
E301099, pg. 69
E301137, pg. 165
E302683, pg. 5
E303143, pg. 130
E303645, pg. 50
E303831, pg. 38
E304657, pg. 22
E305150, pg. 157
E30665, pg. 40
E306782, pg. 72
E307120, pg. 75
E307713, pg. 109
E308859, pg. 83
E309796, pg. 156
E309814, pg. 40
E310222, pg. 22
E310995, pg. 4
E312392, pg. 129
E312680, pg. 130
E313209, pg. 102
E313318, pg. 157
E313732, pg. 22
E314969, pg. 101
E315540, pg. 152
E315636, pg. 161
E315810, pg. 78
E316529, pg. 54
E318039, pg. 105
E318117, pg. 164
E318141, pg. 3
E318168, pg. 27
E318242, pg. 106
E319052, pg. 162
E319574, pg. 41
E319670, pg. 43
E319828, pg. 143
E319901, pg. 87
E320022, pg. 98
E320311, pg. 79
E320521, pg. 103
E321017, pg. 91
E322586, pg. 107
E323060, pg. 131
E323557, pg. 63
E324239, pg. 49
E324738, pg. 74
E324890, pg. 145
E325673, pg. 152
E325903, pg. 46
E325964, pg. 14
E326659, pg. 94
E326687, pg. 64
E326777, pg. 153
E327541, pg. 125
E328326, pg. 112
E329665, pg. 90
E329973, pg. 15
E330040, pg. 25
E330293, pg. 29
E330428, pg. 167
E330600, pg. 34
E330631, pg. 168
E330828, pg. 159
E331480, pg. 109
E332029, pg. 74
E332228, pg. 30
E332257, pg. 33
E332371, pg. 24
E332576, pg. 40
E333077, pg. 166
E333976, pg. 68
E334083, pg. 6
E334246, pg. 33
E334318, pg. 156
E334806, pg. 135
E335345, pg. 130
E336663, pg. 120
E336738, pg. 142
E338098, pg. 171
E338294, pg. 50
E338346, pg. 33
E338973, pg. 143
E339010, pg. 120
E339231, pg. 101
E339601, pg. 82
E339817, pg. 112
E340368, pg. 136
E340391, pg. 111
E340799, pg. 37
E341462, pg. 81
E341517, pg. 131
E341583, pg. 26
E341676, pg. 91
E341775, pg. 142
E341820, pg. 49
E342085, pg. 145
E342212, pg. 81
E342333, pg. 171
E342484, pg. 151
E342497, pg. 46
E343579, pg. 62
E343812, pg. 120
E343895, pg. 140
E344189, pg. 63
E344463, pg. 64
E344900, pg. 110
E344915, pg. 139
E345129, pg. 15
E345255, pg. 95
E345360, pg. 145
E345554, pg. 39
E345929, pg. 88
E346373, pg. 63
E346915, pg. 86
E346985, pg. 41
E346996, pg. 148
E347032, pg. 149
E347113, pg. 25
E347462, pg. 108
E347776, pg. 139
E347782, pg. 98
E347915, pg. 45
E348149, pg. 151
E348276, pg. 39
E348280, pg. 44
E348340, pg. 141
E348360, pg. 142
E348495, pg. 98
E348513, pg. 17
E348519, pg. 153
E348777, pg. 158
E348779, pg. 100
E348871, pg. 74
E348993, pg. 108
E349510, pg. 52
E349550, pg. 75
E349849, pg. 171
E350092, pg. 85
E350225, pg. 81
E350268, pg. 171
E350477, pg. 67
E350640, pg. 167
E350828, pg. 67
E350856, pg. 167
E350879, pg. 149
E350958, pg. 15
E351057, pg. 101
177
E351123, pg. 26
E351199, pg. 51
E351371, pg. 30
E351540, pg. 33
E351950, pg. 106
E352383, pg. 45
E352418, pg. 107
E352531, pg. 110
E352604, pg. 65
E352634, pg. 41
E352678, pg. 67
E352708, pg. 151
E352755, pg. 141
E352767, pg. 166
E352796, pg. 30
E352989, pg. 98
E353017, pg. 41
E353283, pg. 81
E353449, pg. 34
E353792, pg. 95
E353861, pg. 97
E354191, pg. 51
E354416, pg. 78
E354486, pg. 61
E354509, pg. 138
E354869, pg. 132
E355230, pg. 20
E356111, pg. 85
E356129, pg. 74
E356192, pg. 44
E356485, pg. 72
E356565, pg. 69
E356842, pg. 141
E357006, pg. 91
E357358, pg. 70
E357471, pg. 29
E357752, pg. 22
E357849, pg. 149
E357992, pg. 158
E358503, pg. 38
E358556, pg. 107
E358648, pg. 101
E359095, pg. 69
E359272, pg. 50
E359615, pg. 149
E359881, pg. 134
E360000, pg. 140
E360042, pg. 96
E360604, pg. 47
E36102, pg. 174
E361402, pg. 31
E361431, pg. 42
E361442, pg. 4
E362059, pg. 159
E362079, pg. 39
E362201, pg. 31
E362256, pg. 68
E362393, pg. 172
E362583, pg. 121
E362622, pg. 100
E362917, pg. 48
E362949, pg. 136
E363009, pg. 155
E363080, pg. 84
E363474, pg. 72
E363566, pg. 15
E363669, pg. 139
E363988, pg. 140
E364066, pg. 53
E364127, pg. 108
E364207, pg. 23
E364415, pg. 68
E364429, pg. 36
E364455, pg. 166
E364597, pg. 89
SIGN COMPONENTS MANUAL (SAM)
E364680, pg. 45
E364797, pg. 25
E364872, pg. 144
E365284, pg. 31
E365373, pg. 87
E365838, pg. 64
E39591, pg. 2
E464624, pg. 13
E464648, pg. 38
E464766, pg. 156
E466002, pg. 24
E55183, pg. 30
E60612, pg. 87
E65361, pg. 8
E73588, pg. 139
E80767, pg. 14
E80939, pg. 21
E86197, pg. 143
E90751, pg. 80
E97069, pg. 32
COMPANY NAME INDEX
3A Composites USA Inc, pg. 7
3M Company 3M Commercial
Graphics Div, pg. 8
3M Company Industrial Adhesives &
Tapes Div, pg. 13
AA LED Supply Corp, pg. 14
ABC Sign Products, pg. 14
Able Applied Technologies Ltd., pg.
15
Acrosentec Co Ltd., pg. 15
Adhesive Systems Inc., pg. 15
Agilight Inc, pg. 16
Aion LED Inc, pg. 17
Allanson International Inc, pg. 2, 18
Alumet Supply Co Ltd, pg. 20
APM Hexseal Corp, pg. 21
Arlon Graphics LLC, pg. 21
Artemedia Worldwide Ltd, pg. 22
Artware Telecomunication Co Ltd,
pg. 22
Astrodyne Corp, pg. 22
Atex Co Ltd, pg. 22
Autec Power Systems Inc, pg. 23
Ava Technology Inc, pg. 24
Avery Dennison Corp, pg. 24
AVL Inc, pg. 25
Axiomled Inc, pg. 25
B Edwards & Associates LLC, pg. 25
Bayer Materialscience LLC, pg. 26
Bitro Group Inc, pg. 26
Blueview Elec-Optic Tech Co Ltd, pg.
27
BOCA Flasher Inc, pg. 28
Brand W LLC, dba Eco Light LED,
pg. 29
Bu-Chang, pg. 29
Cao Lighting Inc, pg. 30
CGate Solutions Ltd, pg. 30
Chainzone Technology Co Ltd, pg. 5
Channelume/Let-R-Edge, pg. 30
Cirrus Systems Inc, pg. 30
Citylux (China) LED Lighting Ltd, pg.
31
Cleanlife Energy LLC, pg. 31
Cooledge Lighting, pg. 31
Cooley Inc, pg. 32
Cooper Wheelock Inc, pg. 3
Core Lighting Group Inc, pg. 33
CPI Advanced Inc, pg. 33
CPI Advanced Inc, dba Enaba, pg. 33
January 23, 2014
Custom Assembly Solutions Inc, pg.
33
D & P Custom Lights Inc, pg. 33
Daehan Trans Co Ltd, pg. 34
Daehan Ultravision Co Ltd, pg. 5
Daesang Inc, pg. 34
Daikan Co Ltd, pg. 34
Daktronics Inc, pg. 35
Dasan Ad Co Ltd, pg. 36
Dawen Inc, pg. 37
Decora Industries Inc Data Display
Systems Div., pg. 38
Decors USA LLC, pg. 38
Delta Electronics Inc, pg. 38
DGI, pg. 39
Diode LED, pg. 39
Dongbu Lightec Canada Inc, pg. 39
Dongbu Lightec Co Ltd, pg. 40
DTS Mechelec Ltd, pg. 40
Dynapac Rotating Co, pg. 40
Eastman Chemical Co, pg. 41
Ebsco Sign Group LLC, pg. 41
Edge Light Industry Co Ltd, pg. 41
EGL Co Inc, pg. 41
Einsteck Enterprise LLC, pg. 42
Electraled Inc, pg. 42
Electro-Luminx Lighting Corp, pg. 43
Electronic Displays Inc, pg. 44
Elemental LED LLC, pg. 44
E-Lite Technologies Inc, pg. 41
Enhance Neon Tech (Shanghai) Co
Ltd, pg. 44
Enseicom Signs Inc, pg. 45
Espen Technology Inc, pg. 45
Estrakon Inc, pg. 45
Eurocom-Inc, pg. 46
Everbrite Electronics Inc, pg. 46
Everbrite LLC, pg. 2, 46
Everylite LLC, pg. 47
Excellart Sign Products LLC, pg. 47
Fantastic Displays Inc, pg. 48
Federal Heath Sign Co. LLC, pg. 48
Feelis Co Ltd, pg. 49
Fiber Optic Lighting Inc, pg. 49
First System Co Ltd, pg. 50
Flextronics Lighting Solutions Inc,
pg. 50
Foshan Lihao Advertising Signs Co
Ltd, pg. 50
France A Scott Fetzer Co, pg. 2, 50
Fulham Co Ltd, pg. 51
Fulham Electronic Co Ltd, pg. 52
Futurelight Co Ltd, pg. 53
Futuremedia Displays Inc, pg. 54
Futuremedia Displays Inc., pg. 5
G E Lighting Israel Ltd, pg. 54
GE Lighting Solutions LLC, pg. 55
Gemini Inc, pg. 60
General LED, pg. 61
Giantech Industries Co Ltd, pg. 62
Global Lux Inc, pg. 63
Global Sign Products LLC, pg. 63
Globe to Green Lighting LLC, pg. 63
Glux Visual Effects Tech (Shenzhen)
Co Ltd, pg. 64
GM Lighting LLC, pg. 64
GOQLED Co Ltd, pg. 64
Grandlite International Corp, pg. 65
Grate Signs Inc, pg. 65
Gre Alpha Electronics Ltd, pg. 65
Great Lakes Sign Supply Co, pg. 66
Green LED Lighting Solution LLC,
pg. 67
Green LED MFG, pg. 67
Grimco Inc, pg. 67
January 23, 2014
Guangzhou Fangcun Hongmei Neon
Equipment Factory, pg. 68
Guangzhou Future LED Co Ltd, pg.
68
Guangzhou Linong Lighting
Technology Co Ltd, pg. 68
Hato Lighting B V, pg. 69
Heico Lighting, Div of EMD
Technologies Co, pg. 3
Heico Lighting, Div of EMD
Technologies Inc, pg. 69
HENGFU CORP, pg. 69
Hera Lighting L P, pg. 70
High Perfection Technology Co Ltd,
pg. 70
HP Tec, pg. 72
Hubei Flexmedia Co Ltd, pg. 72
Hudnut Co Inc, pg. 72
Hyrite Lighting Co, pg. 72
Hyundai LED Co Ltd, pg. 73
I Light Technologies, pg. 73
ICM Corp, pg. 73
ILight Technologies Inc, pg. 74
Innopol-E Co Ltd., pg. 74
Insight Lighting Co., pg. 74
International Light Technologies Inc,
pg. 74
Interone, pg. 75
Intertek Corp, pg. 75
Inventronics (Hangzhou) Co Ltd, pg.
78
Ipan LED Inc, pg. 78
ITW Plexus / Devcon, pg. 79
Jewelite Wagner Zip-Change Inc, pg.
80
Jiangsu Sino Opto Co Ltd, pg. 81
Jiangyin Huanhong Alubond Metal
Industrial Co Ltd, pg. 81
Jiangyin Pivot Decorative Materials
Co Ltd, pg. 81
Jinbo Kechuang Electronics Co Ltd,
pg. 81
JKL Components Corp, pg. 82
Johnson Walker & Associates LLC,
dba Imperial Plastics Mfg, pg. 82
JS LED Technology Corp, DBA JS
LED Power Inc, pg. 83
Justin Inc, pg. 84
Kason Industries Inc, pg. 84
KBJ Signs Inc, pg. 85
Keledo International BV, pg. 86
Keystone Technologies LLC, pg. 85
Laminators Inc, pg. 87
Lane Technical Sales Inc, pg. 87
LED Era LLC, pg. 87
LED For You Co Ltd, pg. 88
LED Inc, pg. 88
LED Kingdom Inc, pg. 89
LED Lighting Engineering & Design
Corp, pg. 90
Leding Solid State Lighting LTD, pg.
91
Ledstore International Corp, pg. 91
Leotek Electronics Corp, pg. 91
Leotek Electronics USA Corp, pg. 93
Leyard Optoelectronic Co Ltd, pg. 94
Light Beam Industries LLC, pg. 95
Light Engine Ltd, pg. 95
Light Source Solutions LLC, pg. 95
Lightboard Technologies LLC, pg. 95
Linkcom Mfg Co Ltd, pg. 96
Litecorr international Co Ltd, pg. 97
Lord Corporation, pg. 97
Louisville Lamp Co., pg. 98
SIGN COMPONENTS MANUAL (SAM)
Lucky Valley Technology (Shenzhen)
Co Ltd, pg. 98
Luckystar Electronic Technology Co
Ltd, pg. 98
Lumificient Corp, pg. 99
Luminii Corp, pg. 100
Lumiron Inc, pg. 100
Lunera Lighting Inc, pg. 100
LVC Connectors Inc, pg. 101
Magtech Industries Corp, pg. 101
Matrix Frame, pg. 101
Maxbrite LED Lighting Technology
LLC, pg. 102
Mean Well Enterprises Co Ltd, pg.
103
Megapull Inc, pg. 105
MIC Electronics LTD, pg. 106
Micralux Inc, pg. 106
Mitsubishi Plastics Composites
America Inc., pg. 106
Multipanel UK Ltd, pg. 107
N Glantz & Son, pg. 107
Nanjing Cedar Green Technologies
Co Ltd, pg. 107
Nanolumens Inc, pg. 108
NC LED Co Ltd, pg. 108
NCTech Co Ltd, pg. 108
Nemco Controls Inc, pg. 173
Neon Tech, pg. 109
Neo-Neon LED Lighting International
Ltd, pg. 108
NexusLED Green Technology SDN
BHD, pg. 109
Niven Marketing Group, pg. 110
Nora Lighting, pg. 110
Norlok Technology Inc, pg. 110
Nudo Products Inc, pg. 111
OK Industry Inc, pg. 111
Olsen Gaming Inc, dba Spectronix,
pg. 6
Open NV, pg. 6
Optec Displays Inc, pg. 6
Optek Technology Inc, pg. 112
Order-Matic Electronics Corp, pg.
112
Osram Sylvania Inc, pg. 112
Outwater Plastics Industries Inc, pg.
120
Paige Electric Co L P, pg. 120
Palram Americas Inc, pg. 120
Paltronics Inc, pg. 6
Parmida LLC, pg. 121
Permlight Products Inc, pg. 121
Persona Inc, pg. 125
Philips Lighting BV, pg. 125
Philips Lighting Electronics N A, pg.
126
Philips Solid-State Lighting
Solutions Inc, pg. 129
Planar Systems Inc, pg. 130
Polybrite International, pg. 130
Polymer Composite Asia SDN BHD,
pg. 4
Pop Displays USA LLC, pg. 130
Precision Multiple Controls Inc, pg.
174
Principal LED, pg. 131
Process Displays Co, pg. 4
Process Retail Group Inc, pg. 132
Pro-Lite Inc, pg. 131
PWM GMBH & Co KG, pg. 132
Quasar Light Co Ltd, pg. 134
RAB Lighting Inc, pg. 134
RC Global Industries, pg. 135
Relume Technologies TM, pg. 136
178
Retop LED Display Co Ltd, pg. 136
Rishang Optoelectronics Co Ltd, pg.
136
Robertson Worldwide, pg. 138
Rocox Inc, pg. 139
Rosti Integrated Manufacturing
Solutions (Suzhou) Co Ltd, pg. 139
RTC Industries Inc, pg. 4
S & F Supplies Inc, pg. 139
Sabic Innovative Plastics US LLC,
pg. 139
Seoul Semiconductor, pg. 139
Shanghai Huili Tuvgal Sheets Co Ltd,
pg. 140
Shanghai Jiatang Electronic Co Ltd,
pg. 140
Shanghai WHQ Optoelectronic Co
Ltd, pg. 140
Shead Enterprises Inc, pg. 140
Shenzhen Bright Lighting Techology
Co Ltd, pg. 141
Shenzhen Collesun Lighting Co Ltd,
pg. 141
Shenzhen Liantronics Co. Ltd., pg. 6
Shenzhen Lingbenyang Technical Co
Ltd, pg. 141
Shenzhen Suncen Hi-Tech Co Ltd,
pg. 142
Sicom Systems, pg. 142
Sign Crafters Inc, pg. 142
Sign LED Corp, dba LED Express,
pg. 143
Sign Specialties Inc, pg. 143
Sign/Lite Inc, pg. 143
Signalex Inc, pg. 143
Signcomp, pg. 143
Signtronix, pg. 144
Silicon Constellations Inc, pg. 145
Sino-Opto USA LLC, dba LED
Lighting Services LLC, pg. 145
SloanLED, Div of Sloan Co Inc, pg.
145
SS Light Co Ltd, pg. 148
Startec Co Ltd, pg. 149
Sunsignled Opto-Electronics Co Ltd,
pg. 149
Super Bright LEDs Inc, pg. 149
Super X Mfg Ltd, pg. 149
Sydemex, pg. 151
Tactec Aplied Optoelectronics, pg.
151
Taiwan Oasis Technology Co Ltd, pg.
152
Tech 22, pg. 152
Techni-Lite Systems Inc, pg. 152
Technolux Inc, pg. 153, 172
Tecled Electronic Inc, pg. 153
Ten Pao Industrial Co Ltd, pg. 153
The Bright Group Pty Ltd, pg. 154
Tivoli LLC, pg. 155
T-LED System Inc, pg. 151
Transco To Go LLC, pg. 155, 172
Transitions Digital Graphics LLC, pg.
156
Transportation Control Systems Inc,
pg. 156
Triad Magnetics, pg. 157
Tridonic GMBH & Co KG, pg. 157
Tri-Mag LLC, pg. 156
Tronicc Technologies, pg. 158
Tube Lighting Products, pg. 158
U S LED Ltd, pg. 158
Unilumin Group Co Ltd, pg. 159
Union Elecom Co Ltd, pg. 159
179
Universal Lighting Technologies, pg.
161
Ventex Technology Inc, pg. 3, 162
Verseidag-Indutex GMBH, pg. 164
Vintech Industries, pg. 164
Virginia Optoelectronics Inc, pg. 165
Visual Lighting Technologies, pg.
166
Vynex Sign Systems Ltd, pg. 166
W R Pabich Manufacturing Co Inc,
pg. 166
Wai Chi Opto Techology Ltd, pg. 166
Walt Disney Imagineering, pg. 166
Watchfire Signs by Time O Matic Inc,
pg. 167
Westrim Products, pg. 167
White Lightning Fixtures Ltd, pg. 167
Yaham Optoelectronics Co Ltd, pg.
168
Yesco LLC, pg. 169
Young Electric Sign Co, pg. 7
Yuyang DNU Co Ltd, pg. 171
Zhangjiangang Feiteng Aluminum
Composite Panel Co Ltd, pg. 171
Zhejiang Dot Lighting Co Ltd, pg. 171
Zlight Technology LLC, pg. 171
Zuni Scrolling Signs LLC, pg. 172
PRODUCT NAME INDEX
Adhesive Tapes, pg.15, 17
Adhesives, pg.53, 63, 89
Ballast and Lamp System, pg.77
Changing Message Signs
Controllers
LED, pg.12
LED Controller, pg.12
LED Modules, pg.11, 12, 33, 34
Poster Scrolling Frames, pg.12
Sign Display, pg.12
Transformer Assembly, pg.104
Channel Letters
Sign Body
Plastic, pg.45, 46
Channel Letters
Enclosure Rated
Plastic, pg.45
Fluorescent, pg.88
Plastic, pg.45
Sign Body
Plastic, pg.45
Sign Faces
Plastic, pg.45
Trim, pg.40, 55, 100
Trims, pg.45, 86
Christmas Tree Fasteners, pg.6
Coatings
Wood, pg.30
Cold Cathode Fluorescent
Lighting Assemblies, pg.95, 96
Controller, pg.55
Controllers
Decoder, pg.104
Incandescent Lamp, pg.94
Lamp, pg.94
LED, pg.28, 83
LED, pg.94
Scrolling Sign, pg.86
Cooling Fan System, pg.44
Electroluminescent
Drivers, pg.38
Lamps, pg.38
Electroluminiescent
Panel, pg.36
SIGN COMPONENTS MANUAL (SAM)
Faces
Flexible, pg.13, 14, 24, 31, 32, 98,
100, 103
Non-Enclosure Rated
Rigid, pg.37
Rigid, pg.23, 87
Enclosure Rated, pg.92
Enclosure Rated, pg.87
Not Enclosure Rated, pg.14
Fiberoptic Illuminator, pg.105
Flashers, pg.104, 108
Flexible Metal Conduit, pg.6
Fluorescent
Grids, pg.94
Frames, pg.41
Gaskets, pg.6
GTO Cable with Integral Sleeve and
Electrode Enclosure, pg.107
Insulating Bushings, pg.6
Joiner
Metal, pg.30
Lampholder Adapters, pg.19
LED
Light Bar, pg.10
LED
Border Tubing
Rectifier, pg.71
Changing Message sign Module,
pg.26
Class 2, pg.33
Class 2 Controller, pg.101
Class 2 Controllers, pg.29
Class 2 Dimmer Controllers, pg.76
Class 2 Driver, pg.47
Class 2 Drivers, pg.21, 24, 28, 31,
32, 35, 44, 48, 56, 60, 61, 64, 65,
67, 68, 69, 73, 75, 76, 79, 80, 81,
82, 85, 90, 91, 97, 98, 102, 106
Class 2 LED Lamp, pg.105
Class 2 LEDs, pg.24
Class 2 LEDs, pg.20, 22, 24, 25, 26,
27, 28, 29, 30, 32, 33, 35, 36, 42,
46, 47, 48, 55, 56, 57, 58, 59, 60,
62, 63, 64, 66, 71, 72, 73, 74, 75,
78, 79, 82, 83, 84, 85, 86, 87, 89,
90, 91, 92, 93, 94, 95, 97, 98, 99,
100, 101, 104, 105, 106
Flexible, pg.58
Class 2 LEDs Color Controllers,
pg.29
Class 2 Module, pg.62
Class 2 Modules, pg.25, 26, 34
Class 2 Panel, pg.72
Computer, pg.105
Dimmer, pg.82
Driver, pg.48
Class 2, pg.34
Driver Enclosure, pg.99
Drivers, pg.33
Class 2, pg.22
Isolated Output, pg.22
End Cap, pg.66
Lead Wire, pg.67
Leader Cable, pg.83
LED Driver, pg.105
Lighting Assemblies, pg.105
Lighting Assembly, pg.77
Lighting System, pg.99
Module
Class 2, pg.40, 41, 42, 83
Modules
Class 2, pg.22, 77, 85
Outline Lighting, pg.83
Panels, pg.88
Photocell, pg.78
January 23, 2014
Receptacle and Class 2 supply,
pg.84
Regulator, pg.29
Splice Connectors, pg.66
LED Message Readout Sign, pg.11
Neon
Boots
End Caps, pg.95
Residential Neon, pg.39
Splice Insulators, pg.102
controller, pg.41
Electrode Receptacle
Insulators, pg.96, 103
Lighting Assembly, pg.96
Polymeric neon electrode
enclosure, pg.96
Polymeric neon electrode
enclosures, pg.39
Power Supplies, pg.6
Indoor Type 7, pg.8, 9
Power Supply
Indoor Type 7, pg.7
Transformers, pg.6
Indoor 7, pg.10
Indoor Type 1, pg.7, 9
Indoor Type 2, pg.7
Indoor Type 7, pg.7
Outdoor Type 2, pg.7, 8
Outdoor Type 4, pg.7, 8
Outdoor Type 5, pg.7, 8, 9
Outdoor Type 7, pg.8, 9, 10
Tube supports, pg.39
Tube Supports
Spacer Pad, pg.39
Neon Power Suppies
Dimmers
Load, pg.93
Neon Power Supplies
Controllers, pg.93
Dimmers, pg.93
Panel
Structural, pg.21, 46
Panels
Structural, pg.30, 47, 57, 70, 72
Seals, pg.6
Self Ballasted Lamp
Cold Cathode, pg.105
Sign Face Tensioning System, pg.19,
42, 80, 84, 88, 89, 96
Sign Flashers, pg.43, 44, 87, 104, 108
Sign Letters
LED
Class 2, pg.80
Sign Rotators, pg.36
Signs
Portable
LED, pg.10
Signs Face Frame, pg.10
Sleeving
electrical coated, pg.108
Switch
Boots
Push Button, pg.23
Rocker, pg.23
Toggle, pg.22, 96
Toggler, pg.23
Box, pg.39
Photoelectric, pg.108
Special Use, pg.109
Switch & Boot, pg.103
Tubing
Extruded Insulating, pg.109
Mechanical Protection, pg.109
Velcro, pg.6
Wire Positioning Devices, pg.109
January 23, 2014
SIGN COMPONENTS MANUAL (SAM)
180

Similar documents

×

Report this document