RUCKUS 1:18-SCALE 4WD MONSTER TRUCK INSTRUCTION MANUAL ECX01000|ECX01000EU|ECX01000UK

Document technical information

Format pdf
Size 7.2 MB
First found Jun 9, 2017

Document content analysis

Language
English
Type
not defined
Concepts
no text concepts found

Persons

Jeff Bezos
Jeff Bezos

wikipedia, lookup

Organizations

Places

Transcript

RUCKUS
1:18-SCALE 4WD MONSTER TRUCK
®
ECX01000|ECX01000EU|ECX01000UK
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE
Congratulations on your purchase of the ECX® Ruckus®
4WD Monster Truck. This 1:18-scale model introduces
you to the sport of RC driving.
Herzlichen Glückwunsch zum Kauf des ECX Ruckus
4WD Monster Truck. Dieses 1:18 Scale Model öffnet
Ihnen die Welt des RC Car Sports.
Nous vous félicitons pour l’achat du ECX Ruckus
4WD Monster Truck. Ce modèle 1:18 vous introduit au
sport de la conduite RC.
Congratulazioni per l’acquisto di questo Ruckus ECX
4WD Monster Truck. Questa vettura in scala 1:18 vi
introdurrà nel mondo dei modelli RC.
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For
up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious
injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR
create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product
or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible
components or alter this product in any way outside of the instructions provided by Horizon Hobby, Inc. This manual contains
instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the
manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or
result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference
from many sources outside your control. This interference can
cause momentary loss of control, so it is advisable to always
keep a safe distance in all directions around your model as this
margin will help avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from
full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas
for any reason.
• Carefully follow the directions and warnings for this and any
optional support equipment (chargers, rechargeable battery
packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of
the reach of children.
• Never lick or place any portion of the model in your mouth as
it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp
edges.
• Immediately after using your model, do NOT touch equipment
such as the motor, electronic speed control and battery,
because they generate high temperatures. You may burn
yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving
parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the
receiver in the car. Always turn off the receiver before
turning your transmitter off.
• Keep the wheels of the model off the ground when checking
the operation of the radio equipment.
TABLE OF CONTENTS
Specifications ................................................................................. 3
Components ................................................................................... 4
Charging Warnings ........................................................................ 4
Charging the Vehicle Battery ......................................................... 4
Removing the Vehicle Body ........................................................... 5
Installing Transmitter Batteries ..................................................... 5
Transmitter Controls....................................................................... 6
Installing the Vehicle Battery ......................................................... 6
Getting Started............................................................................... 7
Installing the Vehicle Body ............................................................ 7
Operation........................................................................................ 8
2
RUCKUS 4WD
When You Are Finished.................................................................. 8
Setting the Gear Mesh................................................................... 9
Initial Setup .................................................................................... 9
Binding ........................................................................................... 9
Maintenance ................................................................................ 10
Troubleshooting Guide ................................................................. 10
Limited Warranty ......................................................................... 11
Warranty and Service Contact Information ................................. 12
Compliance Information For The European Union ....................... 12
Parts Diagram.......................................................................... 48-50
Parts List....................................................................................... 51
EN
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with
a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions”, including
puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a
submarine. The various electronic components used in the vehicle,
such as the Electronic Speed Control (ESC), servo(s) and receiver
are waterproof, however, most of the mechanical components are
water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts,
as well as the contacts in the electrical cables, will be susceptible
to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance
of your vehicle and to keep the warranty intact, the procedures
described in the “Wet Conditions Maintenance” section below
must be performed regularly if you choose to run in wet conditions.
If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those
conditions.
CAUTION: Failure to exercise caution while using this
product and complying with the following precautions
could result in product malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures
and make sure that you have all the tools you will need to
properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the
battery manufacturer before use. Caution should be taken
when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your
transmitter’s manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning
may be present.
• Do not operate your vehicle where it could come in contact
with salt water (ocean water or water on salt-covered
roads), contaminated or polluted water. Salt water is very
conductive and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor
if it has not been certified as water-resistant or waterproof.
If the motor becomes excessively wet, apply very light
throttle until the water is mostly removed from the motor.
Running a wet motor at high speeds may rapidly damage the
motor.
• Driving in wet conditions can reduce the life of the motor.
The additional resistance of operating in water causes
excess strain. Alter the gear ratio by using a smaller pinion
or larger spur gear. This will increase torque (and motor life)
when running in mud, deeper puddles, or any wet conditions
that will increase the load on the motor for an extended
period of time.
Wet Conditions Maintenance
• Drain any water that has collected in the tires by spinning
them at high speed. With the body removed, place the vehicle
upside down and pull full throttle for a few short bursts until
the water has been removed.
CAUTION: Always keep hands, fingers, tools and any
loose or hanging objects away from rotating parts when
performing the above drying technique.
• Remove the battery pack(s) and dry the contacts. If you have
an air compressor or a can of compressed air, blow out any
water that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse
the mud and dirt off with a garden hose. Avoid rinsing the
bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the
vehicle and help remove any water that may have gotten into
small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts
with a water-displacing light oil or lubricant. Do not spray the
motor.
• Let the vehicle air dry before you store it. Water (and oil) may
continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and
lubrication of the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil the
bushings with lightweight motor oil.
SPECIFICATIONS
Transmitter
Frequency
Battery
Electronic Speed Control (ESC)
2.4GHz
AA x 4
Servo
Power Supply
Output Torque
Operating Speed
Size
4.8V~6V
41.7 oz-in @6.0V (3.0 kg-cm)
34.7 oz-in @6.0V (2.5 kg-cm)
0.12 Sec/60° @6.0V
0.14 Sec/60° @4.8V
28.19 (L) x 12.8 (W) x 27.0mm (H)
Input Voltage
Electric Capacity (FET)
Electric Capacity (FET)
PWM Frequency
BEC Voltage
Size
Weight
6V–7.4V
Forward 20A/160A
Reverse 20A/160A
1kHz
5V/1A
32.70mm (L) x 33mm (W) x 21mm (H)
27.4 g
RUCKUS 4WD
3
EN
COMPONENTS
1. ECX Ruckus 1:18-scale 4WD Monster Truck
2. Transmitter
3. AA Batteries (4)
4. 7.2V 900mAh Ni-MH Battery
5. 100mAh Wall Charger
®
®
2
3
4
1
5
CHARGING WARNINGS
WARNING: Failure to exercise caution while using this
product and comply with the following warnings could
result in product malfunction, electrical issues, excessive heat,
FIRE, and ultimately injury and property damage.
• Read all safety precautions and literature prior to use of this
product.
• Never leave the battery and charger unattended during use.
• Never allow children under 14 years of age to charge battery
packs.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
• Never allow batteries or charger to come into contact with
moisture at any time.
• Never charge batteries in extremely hot or cold places
(recommended between 50–80°F (10–26°C)) or place in direct
sunlight.
• Always use only Ni-MH rechargeable batteries. This charger
cannot charge batteries such as “heavy duty”, “alkaline”,
“mercury” or “lithium” battery.
• Always connect to the charger correctly.
• Always disconnect the battery and charger after charging and let
them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the
product malfunctions.
• Always make sure you know the specifications of the battery to
be charged or discharged to ensure it meets the requirements of
this charger.
• Always constantly monitor the temperature of the battery pack
while charging.
• Always end the charging process if the charger or battery
becomes hot to the touch or starts to change form during the
charge process.
• Always charge in a well ventilated area.
CHARGING THE VEHICLE BATTERY
1. Connect the battery pack to the charger.
2. Connect the charger to an AC power source.
3. Allow the battery pack to charge for 9 hours.
NOTICE: The vehicle battery charger produces 100 milliamps
per hour. Divide the battery capacity (mAh) on the label by 100 to
determine how long the battery needs to charge. For example, a
900mAh battery requires 9 hours to charge.
4
RUCKUS 4WD
EN
REMOVING THE VEHICLE BODY
INSTALLING TRANSMITTER BATTERIES
1. Slide the panel open on the bottom of the
transmitter.
2. Obey the battery plus (+) and minus (-) diagram
in the transmitter to install 4 AA batteries.
3. Slide the panel closed.
We recommend using only alkaline AA batteries
in the transmitter, however, it is possible to use
rechargeable Ni-MH batteries.
CAUTION: If using rechargeable
batteries, charge only rechargeable
batteries. Charging non-rechargeable batteries
may cause the batteries to burst, resulting in
injury to persons and/or damage to property.
TRANSMITTER BATTERY SAFETY PRECAUTIONS
• Never install damaged batteries.
• Never install batteries of mixed types or of different ages in
the transmitter.
• Always remove exhausted batteries.
• Always remove batteries before storing the transmitter.
• Low battery power can result in loss of control of the RC
vehicle.
RUCKUS 4WD
5
EN
TRANSMITTER CONTROLS
Reverse Switch
Battery Level Indicator
Solid Red and Green:
Battery voltage is
good (above 4V).
Solid Red: Battery
voltage is critically low
(below 4V). Replace
transmitter batteries.
Allows you to change the direction of
steering (ST) and throttle (TH) controls.
(The default setting for steering and
throttle is “NOR”)
Throttle Dual Rate
Power Switch
Adjusts the maximum
amount throttle the
vehicle can be given
Power on or off the transmitter
Steering Rate
Adjusts the amount the
front wheels move when
the steering wheel is
turned left or right
Steering Wheel
Control steering. Right
and Left steering with
ST switch on NOR
(See Reverse Switch)
Throttle Trim
Adjusts the neutral
point of the electronic
speed control
Throttle Trigger
Controls power
to the motor for
forward or reverse
(See TH reverse
switch)
Steering Trim
Adjust to make the
vehicle drive straight
with no input at the
steering wheel
Stop
Forward
(when TH reverse
switch on NOR)
INSTALLING THE VEHICLE BATTERY
1. Turn the battery door latch counter-clockwise to
release the battery door.
2. Remove the battery door from the vehicle.
3. Connect the battery to the Electronic Speed Control
(ESC) /Receiver unit connector within the battery
compartment.
4. Install the vehicle battery pack as shown.
5. Re-install the battery door.
6. Turn the battery door latch clockwise to secure
the door.
6
RUCKUS 4WD
Reverse
(when TH reverse
switch on NOR)
EN
GETTING STARTED
1. Power on the transmitter.
2. Connect the battery to the Electronic Speed Control (ESC) /
Receiver unit and power on the vehicle.
ON
3. Do a test of the transmitter’s control of the vehicle with
the vehicle’s wheels off the ground.
4. Start driving slowly. If the wheels are not straight, adjust the
steering trim dial on the transmitter.
TIP: Seat the motor brushes by driving smoothly on a flat surface
during use of the first battery charge. Properly seating the motor
brushes will increase the life and performance of the motor.
INSTALLING THE VEHICLE BODY
RUCKUS 4WD
7
EN
OPERATION
• ALWAYS turn on your transmitter before you turn on the
receiver in the vehicle. Always turn off the receiver before
turning your transmitter off.
• ALWAYS operate your vehicle in a wide open area. Operating
the vehicle in a small space or indoors can cause overheating
at low speeds. Operating at low speed increases heat in the
electronic speed control (ESC). Overheating can damage the
vehicle and failure may result.
Steering Dual Rate
• If the vehicle turns too sharply and/or spins out easily, reduce
the steering dual rate (turn the knob counterclockwise).
• For sharper or additional steering, increase the steering dual
rate (turn the knob clockwise).
Throttle Operation
• Pull the transmitter trigger to increase throttle.
• Push the trigger to apply brake or reverse.
IMPORTANT: The slower the vehicle is moving, the quicker it
will change from forward to reverse.
WHEN YOU ARE FINISHED
1. Power off the vehicle.
2. Power off the transmitter.
OFF
3. Remove the battery from the vehicle.
8
RUCKUS 4WD
4. Disconnect the battery from the ESC/Receiver unit.
EN
SETTING THE GEAR MESH
The gear mesh has already been set at the factory. Setting the
gear mesh is only necessary when changing motors or gears. You
must remove the vehicle’s gear cover (A) to make this adjustment.
Proper gear mesh (how the gear teeth meet) is important to the
performance of the vehicle. When the gear mesh is too loose, the
spur gear could be damaged by the pinion gear of the motor. If the
mesh is too tight, speed could be limited and the motor and ESC
will overheat. Set the gear mesh by following these simple steps:
1. Remove 7 screws to remove the gear cover (A).
2. Loosen the 2 motor screws (B).
3. Put a small piece of paper (C) between the pinion and spur
gears.
4. Push the gears together while tightening the motor screws.
5. Rotate the gears to remove the paper. The gearing should
move a small amount.
6. Reinstall the gear cover.
A
C
B
INITIAL SETUP
MOTOR CARE
RIDE HEIGHT ADJUSTMENT
• Seat the motor brushes by driving smoothly on a flat surface
during use of the first battery charge.
• Prolong motor life by preventing overheating conditions.
Undue motor wear results from frequent turns, stops and
starts, pushing objects, driving in deep sand and tall grass,
and driving continuously up hill. Not allowing motor to cool
between runs can quickly diminish the performance of your
vehicle. Allow adequate time for motor to cool to ambient
temperature betweens runs for best vehicle performance.
• Over-temperature protection is installed on the ESC to
prevent circuit damage, but cannot protect the motor from
driving against heavy resistance.
Ride height is an adjustment that affects the way the vehicle
jumps, turns and goes over bumps. Drop one end of the vehicle from
approximately 3 inches (75 mm) in height onto a flat surface. When
dropping the front of the vehicle, after the vehicle settles, make
sure the front arms are equal and parallel to the flat surface. Do the
same with the rear to make sure both arms are parallel with the flat
surface. To adjust your ride height, either add or remove spring clips
to achieve the desired ride height.
Lower the front ride height to increase steering. Lower the rear ride
height to increase traction but decrease steering.
BINDING
FAILSAFE
In the unlikely event that the radio connection is lost during use
(possibly due to low transmitter batteries or distance between the
receiver and transmitter), the receiver will hold the steering at the
last command with no throttle.
If the receiver is powered on before powering on the transmitter,
the receiver will enter this failsafe mode. When the transmitter is
powered on, normal control is resumed.
Binding is the process of programming the receiver to recognize the
GUID (Globally Unique Identifier) code of a single specific transmitter.
The included transmitter and receiver are bound at the factory. If you
need to rebind, follow the instructions below.
1. Power off the transmitter and ESC.
2. Connect a fully charged battery pack to the ESC.
3. Press and hold the bind
button while powering
up the ESC. After
2 seconds the ESC will
be in bind mode.
4. Release the bind
button and power on
transmitter.
5. Binding is complete
when you hear three
beeps from the ESC.
Bind button
You must rebind when binding the receiver to a different transmitter.
NOTICE: Do not attempt to bind the transmitter and receiver
if there are other compatible transmitters in bind mode within
400 feet. Doing so may result in unexpected binding.
RUCKUS 4WD
9
EN
MAINTENANCE
Your ECX 1:18 Ruckus 4WD Monster Truck needs periodic maintenance and cleaning to keep performing at its optimal level.
After each run:
1. Look over your vehicle to make sure there is no physical
damage that can impede the operation of your vehicle, such
as broken parts or tires that may have come unglued and
need repair.
2. If there are no defects or broken parts that need to be
repaired, completely wipe down the vehicle and body using
paper towels or shop towels. In hard to reach places, use a
toothbrush or a small brush to remove dirt or debris out of
the small areas that cannot be removed with a towel.
3. Screws can come loose over time and need to be
retightened. For screws fastening into plastic parts, make
sure they fit snugly but are not over tightened, which could
cause the plastic to strip out.
4. If you plan to store your vehicle for more than a week, it is a
good idea to remove the batteries from the radio and vehicle
to prevent any unexpected damage, such as corrosion, that
can result in costly repairs.
NOTICE: A small amount of current is constantly pulled from
the battery when it is plugged in, even with the power switch
turned to OFF. Always unplug your vehicle’s battery from the
ESC when not in use to prevent it from fully discharging.
5. Perform any other needed repairs to parts that may have
broken off the chassis. Driving a damaged vehicle will result
in costly and possibly irreparable damage to the vehicle.
TROUBLESHOOTING GUIDE
Problem
Possible Cause
Solution
Vehicle batteries damaged/low voltage
Charge the vehicle battery pack
Motor dirty or brushes worn
Check/clean/replace the motor
Motor dirty or brushes worn
Check/clean/replace the motor
Bind in drivetrain
Clean/adjust the gear mesh between the spur and pinion gears
Vehicle batteries have low voltage
Charge the vehicle battery pack
Controls Reversed
ST. REV or TH. REV
Change switch position on the transmitter
Motor/ESC overheat
Bind in drivetrain
Clean/adjust the gear mesh between the spur and pinion gears
Transmitter batteries low
Replace/recharge
Short Run Time
Sluggish Action
Doesn’t Operate
Poor Range
Transmitter powered off
Power On
ESC powered off
Power On
AA batteries have low voltage
Charge or replace the vehicle battery pack
Transmitter batteries low
Replace/recharge
Transmitter antenna is damaged or loose Check/tighten
Receiver antenna damaged
10 RUCKUS 4WD
Check/repair/replace
EN
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, Inc., (Horizon) warrants to the original purchaser
that the product purchased (the “Product”) will be free from
defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic
damage, (ii) damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or due to improper use, installation,
operation or maintenance, (iii) modification of or to any part of
the Product, (iv) attempted service by anyone other than a Horizon
Hobby authorized service center, (v) Product not purchased from
an authorized Horizon dealer, or (vi) Product not compliant with
applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT
THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL
SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i) service,
or (ii) replace, any Product determined by Horizon to be defective.
Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are
at the sole discretion of Horizon. Proof of purchase is required for
all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR
PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER
THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall
the liability of Horizon exceed the individual price of the Product
on which liability is asserted. As Horizon has no control over use,
setup, final assembly, modification or misuse, no liability shall
be assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting
liability. If you as the purchaser or user are not prepared to accept
the liability associated with the use of the Product, purchaser
is advised to return the Product immediately in new and unused
condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to
conflict of law principals). This warranty gives you specific legal
rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the
Product has been started, you must contact your local distributor
or Horizon directly. This will enable Horizon to better answer your
questions and service you in the event that you may need any
assistance. For questions or assistance, please visit our website
at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty
and Service Contact Information section to speak with a Product
Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the
Horizon Online Service Request submission process found on our
website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping
carton. Please note that original boxes may be included, but are
not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible
for merchandise until it arrives and is accepted at our facility. An
Online Service Request is available at http://www.horizonhobby.
com/content/_service-center_render-service-center. If you do not
have internet access, please contact Horizon Product Support to
obtain a RMA number along with instructions for submitting your
product for service. When calling Horizon, you will be asked to
provide your complete name, street address, email address and
phone number where you can be reached during business hours.
When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary of the
problem. A copy of your original sales receipt must be included
for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have
any issue with a LiPo battery, please contact the appropriate
Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be serviced
or replaced free of charge. Service or replacement decisions are
at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service
will be completed and payment will be required without
notification or estimate of the expense unless the expense
exceeds 50% of the retail purchase cost. By submitting
the item for service you are agreeing to payment of the service
without notification. Service estimates are available upon request. You must include this request with your item submitted for
service. Non-warranty service estimates will be billed a minimum
of ½ hour of labor. In addition you will be billed for return freight.
Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to
Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/_service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a noncompliant Product will not be serviced. Further, the sender
will be responsible for arranging return shipment of the
un-serviced Product, through a carrier of the sender’s
choice and at the sender’s expense. Horizon will hold noncompliant Product for a period of 60 days from notification,
after which it will be discarded.
RUCKUS 4WD 11
EN
WARRANTY AND SERVICE CONTACT INFORMATION
Country of Purchase
Horizon Hobby
Contact Information
Horizon Service Center
servicecenter.horizonhobby.com/Re(Repairs and Repair Requests) questForm/
www.quickbase.com/db/
Horizon Product Support
bghj7ey8c?a=GenNewRecord
(Product Technical Assistance)
888-959-2306
[email protected]
Sales
888-959-2306
[email protected]
Service/Parts/Sales:
Horizon Hobby Limited
+44 (0) 1279 641 097
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United
Kingdom
Germany
Horizon Technischer Service
Sales: Horizon Hobby GmbH
Christian-Junge-Straße 1
25337 Elmshorn, Germany
France
Service/Parts/Sales:
Horizon Hobby SAS
China
Service/Parts/Sales:
Horizon Hobby – China
United States of
America
United Kingdom
[email protected]
+49 (0) 4121 2655 100
[email protected]
+33 (0) 1 60 18 34 90
[email protected]
+86 (021) 5180 9868
Address
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
11 Rue Georges Charpak
77127 Lieusaint, France
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2013062305
Product(s):
ECX Ruckus 1:18th 4WD MT RTR
Item Number(s):
ECX01000EU, ECX01000UK
Equipment class:
1
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the
provisions of the European R&TTE Directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC:
EN 300-328 V1.7.1: 2006
EN 301 489-1 V1.9.2: 2012
EN301 489-17 V2.1.1: 2009
EN60950-1:2006+A11:2009+A1:2010+A12: 2011
EN55022:2010 + AC:2011
EN55024:2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
June 23, 2013
Steven A. Hall
Executive Vice President and Chief Operating Officer
International Operations and Risk Management
Horizon Hobby, Inc.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste
equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please contact your local city office, your
household waste disposal service or where you purchased the product.
12 RUCKUS 4WD
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÉCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
14
16
15
10
8
14
15
18
3
3
11
18
10
3
14
14
3
3
3
3
14
10
14
14
18
14
3
3
11
14
10
11
2
14
18
10
16
10
2
14
14
14
2
14
2
18
2
14
11
10
48 RUCKUS 4WD
16
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÉCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
22
6
23
2
14
14
7
6
16
8
26
14
25
6
14
14
14
7
1
14
14
19
12
1
14
10
5
11
10
13
9
11
9
19 14
14
9
14
1
4
13
13
14
12
10
5
10
RUCKUS 4WD 49
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÉCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
14
14
13
6
6
14
14
14
14
14
14
21
20
6
20
14
50 RUCKUS 4WD
14
PARTS LIST | ERSATZTEILE | PIÈCES DE RECHANGE | PEZZI DI RICAMBIO
#
Description
Link Set: 1:18 4WD All
Descrizione
Set collegamenti: 1:18 4WD
1 ECX214002
tutti
Front Transmission,
Différentiel avant
Trasmissione anteriore
2 ECX212000
Assembled: 1:18 4WD All
assemblé avec carter
assemblata: 1:18 4WD tutti
Rear Transmission,
Différentiel arrière
Trasmissione posteriore
3 ECX212001
Assembled : 1:18 4WD All
assemblé avec carter
assemblata: 1:18 4WD tutti
Suspension Arm Set:
Set de triangles de
Set bracci sospensione:
4 ECX214000
1:18 4WD All
suspension
1:18 4WD tutti
Spindle, Hub & Carrier Set: ECX 1:18 Achschenkel und Set de fusées et étriers Set fuso, mozzo e supporto:
5 ECX214001
1:18 4WD All
Halter Set
porte fusées
1:18 4WD tutti
6 ECX211001 Chassis Set: 1:18 4WD All
ECX 1:18 Chassis Set
Châssis et renfort
Set telaio: 1:18 4WD tutti
Servo Saver Set:
ECX 1:18 Servo Saver und Sauve servo
Set salva servo:
7 ECX214003
1:18 4WD All
Lenkzubehör
1:18 4WD tutti
Pinion & Spur Gear Set: 1:18 ECX 1:18 Ritzel und
Pignon et couronne
Set pignone e corona: 1:18
8 ECX212002
4WD All
Hauptzahnrad
4WD tutti
Complete Shock Set: 1:18
ECX 1:18 Dämpfer Set
Set d’amortisseurs
Set completo ammortizzatori:
9 ECX213000
4WD All
1:18 4WD tutti
Complete Bearing & Bushing ECX 1:18 Kugellagersatz
Set de roulements et
Set completo di cuscinetti e
10 ECX217000
Set: 1:18 4WD All
paliers
bronzine: 1:18 4WD tutti
Complete Driveshaft Set:
ECX 1:18 Antriebsachsen Set de cardans
Set completo trasmissione:
11 ECX212003
1:18 4WD All
Set
1:18 4WD tutti
Wheel Hex Set: 1:18 4WD All ECX 1:18 Mitnehmer Set
Set d’hexagones de
Set esagoni ruote: 1:18 4WD
12 ECX212004
roues
tutti
Hingepin Set: 1:18 4WD All ECX 1:18 Hingepin Set
Set d’axes de suspension Set perni cerniere: 1:18 4WD
13 ECX216000
tutti
Set de visserie
Set completo viteria: 1:18
Complete Hardware Set: 1:18 ECX 1:18 Zubehörset
14 ECX216001
4WD tutti
4WD All
Slipper Assembly: 1:18 4WD ECX 1:18 Slipper montiert Slipper complet
Gruppo antisaltellamento:
15 ECX212005
All
1:18 4WD tutti
Center Driveshaft Assembly: ECX 1:18 Antriebswelle
Cardan central complet Gruppo trasmissione
16 ECX212006
1:18 4WD All
Mitte montiert
centrale: 1:18 4WD tutti
Motor Mount: 1:18 4WD All ECX 1:18 Motorhalter
Support moteur
Supporto motore: 1:18 4WD
17 ECX212007
tutti
Body Mount Set: 1:18 4WD ECX 1:18
Support de carrosserie
Set supporto carrozzeria:
18 ECX211004
All
Karosseriebefestigungs Set
1:18 4WD tutti
Bumper Set:
ECX Ruckus 1:18 4WD
Set de pare chocs
Set paraurti:
19 ECX211000 1:18 4WD Ruckus
Stoßfänger Set Vorne/
1:18 4WD Ruckus
Hinten
FF/RR Premount Tire: 1:18
ECX Mini Ruckus
Pneus prémontés sur
FF/RR premontaggio gomme:
20 ECX41000 4WD Ruckus
Reifensatz Vorne/Hinten
jantes Av/arr
1:18 4WD Ruckus
verklebt
Body Set, Decorated: 1:18
ECX Mini Ruckus
Carrosserie décorée
Set carrozzeria, decorata:
21 ECX210000 4WD Ruckus
Karosserie lackiert u.
1:18 4WD Ruckus
beklebt
Mini Servo
Mini servo
Mini Servo
22 SPMS401 Mini Servo
Mini ECX/Rx, 2.4GHz, WP
Mini ECX/Rx 2.4Ghz
Module Rx/vario 2.4GHz Mini ECX/Rx, 2.4GHz, WP
23 ECX18001
Spritzwasserdicht
étanche
2-Channel 2.4GHz Transmitter 2-Kanal 2.4 Ghz Sender
Emetteur 2 voies 2.4GHz Trasmettitore 2 canali
24 ECX13001
2.4GHz
Tazer™ 380 Motor
Tazer 380 Motor
Moteur Tazer 380
Motore Tazer 380
25 DYNS1210
7.2V 1200mAh Ni-MH
Battery, EC3
100mA Wall Charger with
27 DYNC1001
EC3™ Connector
26 DYN1473
Beschreibung
ECX 1:18 Kunststoff
Anlenkset
ECX 1:18 Getriebe montiert
vorne
ECX 1:18 Getriebe montiert
hinten
ECX 1:18 Querlenker Set
Description
Set de biellettes
7.2V 1200mAh Ni-MH
Akku, EC3
100ma Netzlader mit EC3
Anschluss
Batterie Ni-Mh 7.2V
1200mA, prise EC3
Chargeur mural 100mA
avec prise EC3
Batteria 7.2V 1200mAh
Ni-MH, EC3
Caricatore da muro 100mA
con connettore EC3
RUCKUS 4WD 51
ECX01000|ECX01000EU|ECX01000UK
www.ecxrc.com
© 2013 Horizon Hobby, Inc.
ECX, the ECX logo, Ruckus, Tazer, EC3 and the Horizon Hobby logo are trademarks
or registered trademarks of Horizon Hobby, Inc.
Created 06/2013
34838

Similar documents

×

Report this document