DSL-524T ADSL Router User’s Guide

Document technical information

Format pdf
Size 2.9 MB
First found Jun 9, 2017

Document content analysis

Language
English , Italian
Type
not defined
Concepts
no text concepts found

Persons

Organizations

Places

Transcript

DSL-524T
ADSL Router
User’s Guide
(March 2005)
DSL524TEUA1
DSL-524T ADSL Router Manual
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case
the user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem
Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en cuyo case,
puede requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des interférences
radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto
può causare interferenze radio, nel cui caso è possibile che l`utente debba assumere
provvedimenti adeguati.
ii
DSL-524T ADSL Router Manual
Warranty and Registration for all Countries and
Regions Except USA
Wichtige Sicherheitshinweise
1.
Bitte lesen Sie sich diese Hinweise sorgfältig durch.
2.
Heben Sie diese Anleitung für den spätern Gebrauch auf.
3.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten
dient ein angefeuchtetes Tuch zur Reinigung.
4.
Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind.
5.
Das Gerät is vor Feuchtigkeit zu schützen.
6.
Bei der Aufstellung des Gerätes ist auf sichern Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen.
Verwenden Sie nur sichere Standorte und beachten Sie die Aufstellhinweise des Herstellers.
7.
Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt. Sorgen Sie dafür, daß diese
Öffnungen nicht abgedeckt werden.
8.
Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9.
Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben.
10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollete auch nichts auf der Leitung abgestellt
werden.
11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
12. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer
Überspannung eine Beschädigung vermieden.
13. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnte einen
Brand bzw. Elektrischen Schlag auslösen.
14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem
Servicepersonal geöffnet werden.
15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu
überprüfen:
a.
Netzkabel oder Netzstecker sint beschädigt.
b.
Flüssigkeit ist in das Gerät eingedrungen.
c.
Das Gerät war Feuchtigkeit ausgesetzt.
d.
Wenn das Gerät nicht der Bedienungsanleitung ensprechend funktioniert oder Sie mit Hilfe dieser Anleitung
keine Verbesserung erzielen.
e.
Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f.
Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. den Orginalteilen entsprechende Teile verwendet werden. Der Einsatz von
ungeeigneten Ersatzteilen kann eine weitere Beschädigung hervorrufen.
17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren Servicepartner. Somit stellen Sie die
Betriebssicherheit des Gerätes sicher.
18. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen Nennstrom bis 6A und einem
Gerätegewicht grőßer 3kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75mm2 einzusetzen.
WARRANTIES EXCLUSIVE
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT DLINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN
LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,
INSTALLATION MAINTENANCE OR USE OF D-LINK'S PRODUCTS.
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED
DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE,
NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND
THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD.
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER
OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE OR INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.
THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT ALLOW THE LIMITATION OR
EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
Limited Warranty
Hardware:
iii
DSL-524T ADSL Router Manual
D-Link warrants each of its hardware products to be free from defects in workmanship and materials under normal use and service
for a period commencing on the date of purchase from D-Link or its Authorized Reseller and extending for the length of time
stipulated by the Authorized Reseller or D-Link Branch Office nearest to the place of purchase.
This Warranty applies on the condition that the product Registration Card is filled out and returned to a D-Link office within ninety
(90) days of purchase. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card.
If the product proves defective within the applicable warranty period, D-Link will provide repair or replacement of the product.
D-Link shall have the sole discretion whether to repair or replace, and replacement product may be new or reconditioned.
Replacement product shall be of equivalent or better specifications, relative to the defective product, but need not be identical. Any
product or part repaired by D-Link pursuant to this warranty shall have a warranty period of not less than 90 days, from date of
such repair, irrespective of any earlier expiration of original warranty period. When D-Link provides replacement, then the defective
product becomes the property of D-Link.
Warranty service may be obtained by contacting a D-Link office within the applicable warranty period, and requesting a Return
Material Authorization (RMA) number. If a Registration Card for the product in question has not been returned to D-Link, then a
proof of purchase (such as a copy of the dated purchase invoice) must be provided. If Purchaser's circumstances require special
handling of warranty correction, then at the time of requesting RMA number, Purchaser may also propose special procedure as may
be suitable to the case.
After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
The package must be mailed or otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall
never be responsible for any software, firmware, information, or memory data of Purchaser contained in, stored on, or integrated
with any product returned to D-Link pursuant to this warranty.
Any package returned to D-Link without an RMA number will be rejected and shipped back to Purchaser at Purchaser's expense,
and D-Link reserves the right in such a case to levy a reasonable handling charge in addition mailing or shipping costs.
Software:
Warranty service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list
of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card. If a Registration Card for the
product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice)
must be provided when requesting warranty service. The term "purchase" in this software warranty refers to the purchase
transaction and resulting license to use such software.
D-Link warrants that its software products will perform in substantial conformance with the applicable product documentation
provided by D-Link with such software product, for a period of ninety (90) days from the date of purchase from D-Link or its
Authorized Reseller. D-Link warrants the magnetic media, on which D-Link provides its software product, against failure during
the same warranty period. This warranty applies to purchased software, and to replacement software provided by D-Link pursuant
to this warranty, but shall not apply to any update or replacement which may be provided for download via the Internet, or to any
update which may otherwise be provided free of charge.
D-Link's sole obligation under this software warranty shall be to replace any defective software product with product which substantially conforms to D-Link's
applicable product documentation. Purchaser assumes responsibility for the selection of appropriate application and system/platform software and associated
reference materials. D-Link makes no warranty that its software products will work in combination with any hardware, or any application or system/platform
software product provided by any third party, excepting only such products as are expressly represented, in D-Link's applicable product documentation as being
compatible. D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide
compatibility when there is fault in the third-party hardware or software. D-Link makes no warranty that operation of its software products will be uninterrupted
or absolutely error-free, and no warranty that all defects in the software product, within or without the scope of D-Link's applicable product documentation, will
be corrected.
Warranty and Registration Information for USA Only
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product
only to the person or entity that originally purchased the product from:
D-Link or its authorized reseller or distributor and
Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions
or Protectorates, and U.S. Military Installations, addresses with an APO or FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will be free from material
defects in workmanship and materials from the date of original retail purchase of the product, for the period set forth below
applicable to the product type (“Warranty Period”), except as otherwise stated herein.
5-Year Limited Warranty for the Product(s) is defined as follows:
Hardware (excluding power supplies and fans) Five (5) Years
Power Supplies and Fans Three (3) Year
Spare parts and spare kits Ninety (90) days
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original
owner or to refund at D-Link’s sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link
Service Office. The replacement Hardware need not be new or have an identical make, model or part. D-Link may in its sole
discretion replace the defective Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is
substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement Hardware will be
warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is
iv
DSL-524T ADSL Router Manual
incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective
Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of
the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall
become the property of D-Link upon replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to
D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of
original retail purchase of the Software for a period of ninety (90) days (“Warranty Period”), provided that the Software is properly
installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the
Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. D-Link’s sole obligation
shall be to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s
functional specifications for the Software or to refund at D-Link’s sole discretion. Except as otherwise agreed by D-Link in writing,
the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted
by D-Link for the Software. Software will be warranted for the remainder of the original Warranty Period from the date or original
retail purchase. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not
practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be
refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license
granted respecting any Software for which a refund is given automatically terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of D-Link's products, will
not be applied to and does not cover any product purchased through the inventory clearance or liquidation sale or other sales in
which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case,
the product is being sold "As-Is" without any warranty whatsoever including, without limitation, the Limited Warranty as described
herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: Any claim under this limited warranty must be submitted in writing before the end of the Warranty Period to
an Authorized D-Link Service Office.
The customer must submit as part of the claim a written description of the Hardware defect or Software nonconformance
in sufficient detail to allow D-Link to confirm the same.
The original product owner must obtain a Return Material Authorization (“RMA”) number from the Authorized D-Link
Service Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase
invoice for the product) before the warranty service is provided.
After an RMA number is issued, the defective product must be packaged securely in the original or other suitable
shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on
the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace
the defective portion of the Product and will not ship back any accessories.
The customer is responsible for all shipping charges to D-Link. No Charge on Delivery (“COD”) is allowed. Products sent
COD will either be rejected by D-Link or become the property of D-Link. Products should be fully insured by the
customer and shipped to D-Link Systems, Inc., 53 Discovery Drive, Irvine, CA 92618. D-Link will not be held responsible
for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped via UPS Ground or
any common carrier selected by D-Link, with shipping charges prepaid. Expedited shipping is available if shipping
charges are prepaid by the customer.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or
for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable
handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing
requirements, or that is determined by D-Link not to be defective or non-conforming.
What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link’s judgment, have been
subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care,
repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has
been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping
costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in
shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other
products or services provided by anyone other than D-Link; Products that have been purchased from inventory clearance or
liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation
pertaining to the product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED
“AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT
BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE
LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE
ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE
PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT,
NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT,
INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE,
COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S
PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY
PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO
WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS
REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF DLINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE
FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER
WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.
Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some states do not allow exclusion
or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing
limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have
other rights which vary from state to state.
Notice of IEEE802.11a 5Ghz radio usage in the European Community
•
At the time of writing this addendum, some countries such as Italy, Greece, Portugal and Spain hasn’t allowed operation of radio
devices in the 5Ghz bands, although operation of 2.4Ghz radio devices are allowed. Please check with your local authority to confirm.
v
DSL-524T ADSL Router Manual
•
This device is restricted to indoor use when operated in the European Community using channels in the 5.15-5.35 GHz band to
reduce the potential for interference.
Usage Notes:
•
To remain in conformance with European National spectrum usage regulations, frequency and channel limitations will be applied
on the products according to the country where the equipment will be deployed.
•
This device is restricted from functioning in Ad-hoc mode while operating in 5Ghz. Ad-hoc mode is direct peer-to-peer
communication between two client devices without an Access Point.
•
Access points will support DFS (Dynamic Frequency Selection) and TPC (Transmit Power Control) functionality as required
when operating in 5Ghz within the EU.
Allowable 802.11a Frequencies and Channels
Countries
5.15-5.25 GHz
(Channels 36, 40, 44, 48)
5.15-5.25 Ghz & 5.725-5.875 Ghz
(Channels 36, 40, 44, 48, 149, 153, 157, 161, 165, 169)
5.15-5.35 GHz
(Channels 36, 40, 44, 48, 52, 56, 60, 64)
5.15-5.35 & 5.47-5.725 GHz
(Channels 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124,
128, 132, 136, 140)
Liechtenstein, Hungary, Switzerland
5.15-5.35 Ghz & 5.725-5.875 Ghz
(Channels 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165, 169)
Czech Republic
IEEE 802.11b 2.4Ghz operation
Countries
2.4-2.4835 Ghz
2.4465-2.4835 Ghz
(Channels 10,11,12,13)
Rest of EU Community
France
Austria
France, Slovak
Denmark, Germany, Iceland, Finland, Netherlands, Norway, Poland,
Sweden, Slovenia, Luxembourg, U.K., Ireland
European Community Declaration of Conformity:
English
Hereby, D-Link Corporation declares that this Wireless LAN device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Finnish
Valmistaja D-Link Corporation vakuuttaa täten että Wireless LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Dutch
Hierbij verklaart D-Link Corporation dat het toestel Wireless LAN device in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG
Bij deze verklaart D-Link Corporation dat deze Wireless LAN device voldoet aan de essentiële eisen en aan de overige relevante
bepalingen van Richtlijn 1999/5/EC.
French
Par la présente D-Link Corporation déclare que l'appareil Wireless LAN device est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE
Par la présente, D-Link Corporation déclare que ce Wireless LAN device est conforme aux exigences essentielles et aux autres
dispositions de la directive 1999/5/CE qui lui sont applicables
Swedish
Härmed intygar D-Link Corporation att denna Wireless LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Danish
Undertegnede D-Link Corporation erklærer herved, at følgende udstyr Wireless LAN device overholder de væsentlige krav og øvrige
relevante krav i direktiv 1999/5/EF
German
Hiermit erklärt D-Link Corporation dass sich dieser/diese/dieses Wireless LAN device in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)
Hiermit erklärt D-Link Corporation die Übereinstimmung des Gerätes Wireless LAN device mit den grundlegenden Anforderungen und
den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)
Greek
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑD-Link Corporation ∆ΗΛΩΝΕΙ ΟΤΙ Wireless LAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ
vi
DSL-524T ADSL Router Manual
Italian
Con la presente D-Link Corporation dichiara che questo Wireless LAN device è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Spanish
Por medio de la presente D-Link Corporation declara que el Wireless LAN device cumple con los requisitos esenciales y cualesquiera
otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE
Portuguese
D-Link Corporation declara que este Wireless LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999
AVERTISSEMENT AUX UTILISATEURS
L’utilisation des bandes de fréquences des 2.4GHz et 5GHz pour les RLAN est réglementée par l’ART (Autorité de Régulation des
Télécoms).
BANDE DE FREQUENCES DES 2.4GHZ
La décision N° 02-1008 en date du 31 octobre 2002 autorise l’utilisation d’une partie de la bande de fréquences 2400-2483,5 MHz pour
les réseaux locaux radioéléctriques (RLAN) comme suit :
L’utilisation de la bande 2400-2446,5 MHz est autorisée à l’intérieur des bâtiments avec une puissance isotrope rayonnée équivalente (PIRE)
limitée à 10 mW et que l’utilisation de la bande 2446,5-2483,5 MHz est autorisée à l’intérieur des bâtiments avec une PIRE limitée à 100 mW.
L’utilisation en extérieur est soumise à demande d’autorisation sur la bande de fréquences de 2446,5-2483,5 MHz avec une puissance limitée à
100mW.
Dans certains départements, dont la liste est publiée par l'Autorité de régulation des télécommunications, l'utilisation de la totalité de la bande
2400- 2483,5 MHz est autorisée à l'intérieur des bâtiments avec une puissance isotrope rayonnée équivalente maximale de 100 mW.
Dans ces mêmes départements, l'utilisation de la bande 2400-2454 MHz est autorisée à l'extérieur des bâtiments avec une puissance isotrope
rayonnée équivalente maximale de 100 mW et l'utilisation de la bande 2454-2483,5 MHz est autorisée à l'extérieur des bâtiments avec une
puissance isotrope rayonnée équivalente maximale de 10 mW.
L’Autorité poursuit les négociations avec le ministère de la Défense en vue de l’ouverture de la totalité de la bande 2400-2483,5 MHz en
intérieur et en extérieur avec une PIRE de 100 mW. Cette ouverture est acquise d'ores et déjà dans certains départements d'Outre-mer.
En installant et utilisant les produits réseaux sans fils de la gamme proposée par D-Link, vous vous engagez donc à respecter cette
réglementation.
Pour tour information complémentaire et les dernières informations concernant l’évolution de la réglementation française, nous
vous conseillons de consulter le site de l’ART : www.art-telecom.fr.
BANDE DE FREQUENCES DES 5GHZ
L’Autorité de Régulation des Télécommunications (ART) autorise l’utilisation d’une partie de la bande de fréquences des 5GHz pour les
réseaux locaux radioélectriques (RLAN) intégrant des solutions 802.11a supportant les fonctions DFS (Dynamic Frequency Selection) et
TPC (Transmit Power Control).
Seule la bande 5150-5350MHz est autorisée en France pour une utilisation intérieure avec une puissance limitée à 200 mW en mode
infrastructure.
En installant et en utilisant les produits réseaux sans fil 802.11a de la gamme D-Link commercialisée en France, vous vous engagez à
respecter cette réglementation.
Pour tour information complémentaire et les dernières informations concernant l’évolution de la réglementation française, nous
vous conseillons de consulter le site de l’ART : www.art-telecom.fr.
AVVERTIMENTI PER GLI UTILIZZATORI
L’utilizzo della banda di frequenza dei 2.4 GHz per applicazioni di tipo Radio LAN sul mercato Italiano, è
regolamentato dal Ministero delle Comunicazioni secondo il Nuovo Piano Nazionale Gestioni Frequenze relativo al
D.M. dell’8 Luglio 2002 e dalle relative modifiche come dal Decreto del Ministero delle Comunicazioni del 20
Febbraio 2003 (nota 158).
Viene definito come Radio Local Area Network (di seguito denominate “Radio LAN” o “R-LAN”) un sistema di
comunicazioni in rete locale mediante radiofrequenze che utilizza apparati a corto raggio secondo le caratteristiche
di armonizzazione e tecniche previste dal vigente Piano nazionale di ripartizione delle frequenze, nelle seguenti
bande di frequenza: 2.400,0 – 2.483,5 MHz (brevemente banda a 2.4 GHz).
I sistemi Radio LAN sono regolati da apposite normative. Principalmente valgono le normative F.C.C. per gli U.S.A.,
il Canada, e gli altri paesi aderenti alle F.C.C., come gli ex paesi U.R.S.S.; mentre le norme E.T.S. 300T-328-2 e
correlate, emanate dall'organo Europeo E.T.S.I., valgono per i paesi dell'Unione Europea, Giappone e per i paesi
aderenti a queste normative.
La normativa tecnica ETS 300T-328-2 impone di non irradiare con una potenza E.I.R.P. superiore ai 100 mW
(equivalente a 20 dBm).
In linea di principio inoltre impone agli apparati Radio LAN, di non trasmettere con una potenza elettrica effettiva
superiore ai 50 mW (equivalente a 17 dBm); questo perché l'antenna a dipolo più semplice, che di solito li
accompagna, ha generalmente un guadagno in trasmissione pari a circa 2.5 dBi, che fa si che la potenza E.I.R.P.
trasmessa salga a circa 80 mW (per la precisione 19.2 dBm).
vii
DSL-524T ADSL Router Manual
Per questo motivo su tutto il territorio dell'Unione Europea, ed anche in Italia, è assolutamente vietato utilizzare
antenne che abbiano un guadagno in trasmissione elevato (in linea di massima diciamo superiore ai 5 dBi), tale da
portare la potenza trasmessa E.I.R.P. oltre i 100 mW (equivalente a 20 dBm).
Nel caso in cui invece sia possibile regolare il livello di potenza trasmessa dagli Access Point, viene data la
possibilità di utilizzare antenne ad alto guadagno attenendosi strettamente ad una serie di istruzioni di seguito
riportate che consentono questo utilizzo rimanendo comunque all’interno della potenza massima trasmessa E.I.R.P.
pari e non superiore a 100mW (20dBm).
CALCOLO DELLA POTENZA E.I.R.P. IN EMISSIONE
La formula di calcolo per ottenere l’E.I.R.P. effettivo è la seguente:
E.I.R.P. (dBm) = Ptx (dBm) + Gtx (dBi) dove
Ptx = Potenza trasmessa al connettore dell’antenna di trasmissione
Gtx = Guadagno dell’antenna di trasmissione
Il valore ottenuto dalla somma, NON deve superare quanto espresso dalla normativa ovvero 20dBm. Nel caso in cui
si voglia convertire il risultato ottenuto in mW, utilizzare la semplice tabella di conversione di seguito riportata.
INSTALLAZIONE ED UTILIZZO DI SITEMI RADIO LAN AD USO PRIVATO
Come riportato nel D.P.R. n° 447/01 Art. 6 – Punto B (Libero uso) del 5 Ottobre 2001:
“Sono di libero uso le apparecchiature che impiegano frequenze di tipo collettivo, senza alcuna protezione, per
collegamenti a brevissima distanza con apparati a corto raggio, compresi quelli rispondenti alla raccomandazione
CEPT-ERC/REC 70-03, tra le quali rientrano in particolare:
b)
Reti locali di tipo radiolan e hiperlan nell’ambito del fondo, ai sensi dell’articolo 183, comma secondo, del
decreto del Presidente della Repubblica n. 156 del 1973; sono disciplinate ai sensi dell’articolo 5 le reti
hiperlan operanti obbligatoriamente in ambienti chiusi o con vincoli specifici
…
Per “fondo” pubblico o privato, si intende un ambiente sia interno che esterno ben circoscritto e delimitato.
Per “fondo privato” possiamo, per esempio, fare riferimento a uffici, capannoni industriali, abitazioni, aree all’aperto
private che non attraversano il suolo pubblico o il passaggio di pubblico dominio/demanio.
Per “fondo pubblico” possiamo, per esempio, fare riferimento a tutti quei luoghi appartenenti allo Stato o alle
amministrazioni centrali e locali quali strade, autostrade, strade ferrate, spiagge, porti, fiumi etc.
E’ comunque necessario fare 2 specifiche distinzioni:
Utilizzo di sistemi Radio LAN ad uso privato con installazioni indoor o outdoor su fondo/suolo privato:
E’ possibile utilizzare liberamente sistemi Radio LAN purché vengano rispettate le normative vigenti soprattutto per
quanto riguarda l’emissione massima in potenza come sopra riportato.
Utilizzo di sistemi Radio LAN ad uso privato con installazioni outdoor con attraversamento di fondo/suolo
pubblico:
Come specificato nel D.P.R. n° 447/01 Art. 5 – Punto 2.2 del 5 Ottobre 2001, è necessario richiedere
un’autorizzazione generale al “Ministero delle Comunicazioni Direzione generale per le concessioni e le
autorizzazioni” per l’installazione di sistemi Radio LAN ad uso privato con installazioni outdoor con attraversamento
di suolo pubblico.
Per richiedere l’autorizzazione generale, fare riferimento all’allegato C presente all’interno del D.P.R. n° 447/01 in
qualità di canovaccio per la stesura della richiesta.
Per ulteriori informazioni e delucidazioni, fare riferimento al D.P.R. n° 447/01 del 5 Ottobre 2001.
INSTALLAZIONE ED UTILIZZO DI SITEMI RADIO LAN AD USO PUBBLICO
viii
DSL-524T ADSL Router Manual
A fronte dell’ultimo decreto relativo all’accesso ad Internet senza fili in regime di autorizzazione generale e uso pubblico
rilasciato dal Ministero delle Comunicazioni in data 28 Maggio 2003, sono stati rivisti i parametri relativi all’installazione ed
all’utilizzo dei sistemi Radio LAN ad uso pubblico.
Per completezza di informazioni, suggeriamo di fare riferimento al decreto in questione disponibile sul sito del Ministero
delle Comunicazioni al link http://www.comunicazioni.it/it/index.php?IdNews=39
ACCESSO ALLE FONTI DI INFORMAZIONE
Per tutte le informazioni complementari, a supporto di questa informativa e concernenti all’evoluzione della normativa
wireless sul territorio italiano, vi preghiamo di fare riferimento al sito Internet del Ministero delle Comunicazioni
http://www.comunicazioni.it
ix
TABLE OF CONTENTS
About This User’s Guide....................................................................................................................................12
Before You Start ................................................................................................................................................12
Installation Requirements...................................................................................................................................12
INTRODUCTION .......................................................................................................15
Router Description and Operation......................................................................................................................15
Front Panel .........................................................................................................................................................17
Rear Panel ..........................................................................................................................................................18
HARDWARE INSTALLATION ..................................................................................19
Location .............................................................................................................................................................19
Network Connection ..........................................................................................................................................19
Power On Router................................................................................................................................................20
Factory Reset Button..........................................................................................................................................20
CONFIGURING THE ROUTER FOR THE FIRST TIME ...........................................21
Configuring IP Settings on Your Computer.......................................................................................................21
Configure IP Settings .........................................................................................................................................22
ACCESSING THE CONFIGURATION MANAGER...................................................24
Configure the Router with the Configuration Wizard ........................................................................................25
HOME........................................................................................................................36
WAN Configuration...........................................................................................................................................36
LAN Configuration ............................................................................................................................................45
DHCP.................................................................................................................................................................46
DNS....................................................................................................................................................................49
Dynamic DNS ....................................................................................................................................................50
ADVANCED CONFIGURATION ...............................................................................51
UPnP ..................................................................................................................................................................51
Virtual Server.....................................................................................................................................................52
LAN Clients .......................................................................................................................................................54
SNMP.................................................................................................................................................................56
Filters .................................................................................................................................................................58
Bridge Filters......................................................................................................................................................60
Routing Table.....................................................................................................................................................62
DMZ...................................................................................................................................................................64
Firewall ..............................................................................................................................................................66
RIP .....................................................................................................................................................................68
PPP.....................................................................................................................................................................69
ADSL .................................................................................................................................................................71
ATM VCC..........................................................................................................................................................73
QoS ....................................................................................................................................................................74
TOOLS ......................................................................................................................76
Admin ................................................................................................................................................................76
Time ...................................................................................................................................................................77
Remote Log........................................................................................................................................................78
System................................................................................................................................................................80
Firmware ............................................................................................................................................................81
Miscellaneous.....................................................................................................................................................82
Test.....................................................................................................................................................................82
STATUS ....................................................................................................................85
Device Info.........................................................................................................................................................85
DHCP.................................................................................................................................................................87
Log .....................................................................................................................................................................88
Statistics .............................................................................................................................................................89
ADSL .................................................................................................................................................................90
Help....................................................................................................................................................................91
TECHNICAL SPECIFICATIONS ...............................................................................94
IP ADDRESS SETUP................................................................................................96
IP CONCEPTS ..........................................................................................................99
MICROFILTERS AND SPLITTERS ........................................................................103
DSL-524T ADSL Router Manual
About This User’s Guide
This manual provides instructions on how to install the DSL-524T ADSL Router and use it to connect
a computer or Ethernet LAN to the Internet.
Before You Start
Please read and make sure you understand all the prerequisites for proper installation of your new
Router. Have all the necessary information and equipment on hand before beginning the installation.
Installation Overview
The procedure to install the Router can be described in general terms in the following steps:
1.
Gather information and equipment needed to install the device. Before you begin the actual installation make sure
you have all the necessary information and equipment.
2.
Install the hardware, that is, connect the cables (Ethernet and telephone) to the device and connect the power
adapter.
3.
Check the IP settings on your computer and change them if necessary so the computer can access the web-based
software built into the Router.
4.
Use the web-based management software to configure the device to suit the requirements of your ADSL account.
Installation Requirements
Information you will need from your ADSL service provider:
Username
This is the Username that is used to log on
to your ADSL service provider’s network. It is
commonly in the form − [email protected]
Password
This is the Password that is used, in
conjunction with the Username above, to log
on to your ADSL service provider’s network.
Connection
Protocol
This is the method that your ADSL service
provider uses to send and receive data
between the Internet and your computer.
VPI
This is the Virtual Path Identifier (VPI). It is
used in conjunction with the Virtual Channel
Identifier (VCI) below, to identify the data
path between your ADSL service provider’s
network and your computer.
VCI
This is the Virtual Channel Identifier (VCI). It
is used in conjunction with the VPI above to
identify the data path between your ADSL
service provider’s network and your
computer.
12
Record your info
here.
DSL-524T ADSL Router Manual
Information you will need about your DSL-524T ADSL Router:
Username
This is the Username you will be prompted
to enter when you access the DSL-524T’s
configuration screens using a Web browser.
The default Username is admin.
Password
This is the Password you will be prompted to
enter when you access the DSL-524T’s
configuration screens using a Web browser.
The default Password is admin.
LAN IP address
for the DSL-524T
This is the IP address you will enter into the
Address field of your Web browser to
access the DSL-524T’s configuration
screens using a Web Browser. The default
IP address is 192.168.1.1.
LAN Subnet Mask
for the DSL-524T
This is the subnet mask used by the DSL524T, and will be used throughout your LAN.
The default subnet mask is 255.255.255.0.
Record your info
here.
Information you will need about your LAN or computer:
Ethernet NIC
If your computer has an Ethernet NIC, you
can connect the DSL-524T to this Ethernet
port using an Ethernet cable. You can also
use the Ethernet port on the DSL-524T to
connect to other Ethernet devices, such as a
Wireless Access Point.
DHCP Client
status
Your DSL-524T ADSL Router is configured,
by default, to be a DHCP server. This means
that it can assign an IP address, subnet
mask, and a default gateway address to
computers on your LAN. The range of IP
addresses the DSL-524T will assign are from
192.168.1.2 to 192.168.1.254. Your
computer (or computers) needs to be
configured to Obtain an IP address
automatically (that is, they need to be
configured as DHCP clients.)
Record your info
here.
It is recommended that your collect and record this information here, or in some other secure place, in
case you have to re-configure your ADSL connection in the future.
Once you have the above information, you are ready to setup and configure your DSL-524T ADSL
Router.
13
DSL-524T ADSL Router Manual
14
DSL-524T ADSL Router Manual
1
Introduction
This section provides a brief description of the Router, its associated technologies and a list of Router
features.
What is ADSL?
Asymmetric Digital Subscriber Line (ADSL) is an access technology that utilizes ordinary copper
telephone lines to enable broadband high-speed digital data transmission and interactive multimedia
applications for business and residential customers. For ADSL services, it is not necessary to install
expensive new cabling or condition the line in any way.
ADSL greatly increases the signal carrying capacity of copper telephone lines without interfering with
regular telephone services. For the ADSL user, this means faster downloads and more reliable
connectivity. ADSL devices make it possible to enjoy benefits such as high-speed Internet access
without experiencing any loss of quality or disruption of voice/fax telephone capabilities.
ADSL provides a dedicated service over a single telephone line operating at speeds of up to 8 Mbps
downstream and up to 640 Kbps upstream, depending on local telephone line conditions. A secure
point-to-point connection is established between the user and the central office of the service provider.
D-Link ADSL devices incorporate the recommendations of the ADSL Forum regarding framing, data
format, and upper layer protocols.
Router Description and Operation
The DSL-524T ADSL Router is designed to provide a simple, cost-effective and secure ADSL
Internet connection for your small- to medium-sized private network. The DSL-524T combines the
benefits of high-speed ADSL connection technology and TCP/IP routing with a conventional Ethernet
interface in one compact and convenient package. ADSL connection technology enables many
interactive multi-media applications such as video conferencing and collaborative computing.
The Router is easy to install and use. The DSL-524T connects to an Ethernet LAN via a standard
Ethernet 10BASE-T interface using RJ-45 connectors. The ADSL connection is made using ordinary
twisted-pair telephone line with standard RJ-11 connectors. This arrangement means that several PCs
can be networked and connected to the Internet using a single WAN interface and IP address.
Low Pass Filters
Since ADSL and telephone services share the same copper wiring to carry their respective signals, a
filtering mechanism may be necessary to avoid mutual interference. A low pass filter device can be
installed for each telephone that shares the line with the ADSL line. These filters are easy to install
passive devices that connect to the ADSL device and/or telephone using standard telephone cable. Ask
your service provider for more information about the use of low pass filters with your installation.
Appendix B provides illustrated examples of how to install two common styles of low pass filters.
Operating Systems
The DSL-524T uses an HTML-based web interface for setup and management. The web configuration
manager may be accessed using any operating system capable of running web browser software,
including Windows 98 SE, Windows ME, Windows 2000, and Windows XP.
15
DSL-524T ADSL Router Manual
Web Browser
Any common web browser can be used to configure the Router using the web configuration
management software. The program is designed to work best with more recently released browsers
such as Mozilla, Firefox, Opera, Microsoft Internet Explorer® version 5.0, Netscape Navigator®
version 4.7, or later versions. The web browser must have JavaScript enabled. JavaScript is enabled by
default on many browsers. Make sure JavaScript has not been disabled by other software (such as
virus protection or web user security packages) that may be running on your computer.
Ethernet Port (NIC Adapter)
Any computer that uses the Router must be able to connect to it through the Ethernet port on the
Router. This connection is an Ethernet connection and therefore requires that your computer be
equipped with an Ethernet port as well. Most notebook computers are now sold with an Ethernet port
already installed. Likewise, most fully assembled desktop computers come with an Ethernet NIC
adapter as standard equipment. If your computer does not have an Ethernet port, you must install an
Ethernet NIC adapter before you can use the Router. If you must install an adapter, follow the
installation instructions that come with the Ethernet NIC adapter.
Additional Software
It may be necessary to install software on your computer that enables the computer to access the
Internet. Additional software must be installed if you are using what is called a “bridged” connection.
For a bridged connection, the information needed to make and maintain the Internet connection is
stored on your computer, not in the Router. This type of connection is similar to the arrangement used
for analog dial-up modems, but the connection speed is much faster. Various terms are to describe a
bridged ADSL connection including the term “RFC 1483 Bridge” which is used in this guide.
About Bridged Ethernet Connections (RFC 1483)
Using this method, the DSL-524T acts as a transparent bridge, and is invisible to other devices on both
the WAN and LAN side of the bridge. It is therefore necessary to provide some means of acquiring
global IP settings for your account.
All connections to the Internet require a unique global IP address. For bridged connections, the global
IP settings must reside in a TCP/IP enabled device on the LAN side of the bridge, such as a PC, server
or firewall hardware. The IP address can be assigned in a number of ways. Your network service
provider will give you instructions about any additional connection software or NIC configuration that
may be required.
Account Information (User Name and Password)
Most users will need to supply a user name and password used to access the service provider’s
network (and ultimately, the Internet). This information is stored either in the Router’s memory or on
your computer depending on the type of ADSL connection you have.
ACCOUNT INFORMATION (PPP Connections Only)
User Name:
Password:
Router Features
The D-Link DSL-524T ADSL Router provides the following features:
•
Data rates up to 24 Mbps for downstream and 1Mbps for upstream
16
DSL-524T ADSL Router Manual
•
•
•
•
•
•
•
•
•
Friendly web-based graphical user interface for configuration and management
Supports up to eight simultaneous virtual connections for a single ADSL account
Supports T1.413 issue 2, G.dmt and G.lite for the ADSL standard
Supports G.dmt.bis and G.lite.bis for the ADSL2 standard
Supports g.992.5 for the ADSL standard
Auto-handshake and rate adaptation for different ADSL flavors
Widest range of DSLAM interoperability
Built-in MIBs for SNMP management
Upgradeable firmware through HTTP
Packing List
Open the shipping carton and carefully remove all items. In addition to this User's Guide, ascertain
that you have:
•
One DSL-524T ADSL Router
•
One twisted-pair telephone cable used for ADSL connection
•
One CAT-5 Ethernet cable
•
One AC power adapter suitable for your electric service
•
This Manual on CD ROM
Front Panel
Place the Router in a location that permits an easy view of the LED indicators on the front panel.
The LED indicators on the front panel include the Power, Status, ADSL Link/Act(ivity) and
Ethernet Link/Act(ivity) indicators.
Power
Steady green light indicates the unit is powered on.
Status
Lights steady green during Power on Self-Test (POST). Once the connection
status has been settled, the light will blink green. A system failure will be
represented by a solid green light or the light going dark.
Steady green light indicates a valid ADSL connection. This will
ADSL: Link/Act light after the ADSL negotiation process has been settled.
Blinking green light indicates activity on the WAN interface.
A solid green light will indicate a valid link on startup. This light
Ethernet:
will blink when there is activity currently passing through the
Link/Act
Ethernet port.
17
DSL-524T ADSL Router Manual
Rear Panel
Connect the AC power adapter cord and network cables on the rear panel. The power switch and reset
button are also located on the back of the device. Connect the antennas to the antenna posts.
All cable connections to the Router are made at the rear panel. The power switch and factory reset
button is located here as well.
ADSL port,
connect ADSL
cable here
Factory reset
button
Ethernet port,
connect
Ethernet cable
18
Power cord
connects
here
DSL-524T ADSL Router Manual
2
Hardware Installation
The DSL-524T functions on two separate networks, as an Ethernet LAN and as an ADSL WAN.
When deciding where to put the Router, the user must take into account the fact that it is connected to
these three networks with three types of media. Ethernet cables connect the Router to computers and
network devices, and the ADSL line connects it to a wall socket. In addition, the device must be near
an AC outlet for power. How to accommodate these wired connections is often not a complicated
matter, however, the added dimension of wireless communication does complicate the decision of
Router placement.
Location
The Router can be placed on a shelf or desktop and ideally you should be able to see the LED
indicators on the front if you need to view them for troubleshooting.
Network Connection
Complete the connection to the network through the ADSL port and the Ethernet port on the back of
the Router.
Connect ADSL Line
Use the ADSL cable included with the Router to connect it to a telephone wall socket. Plug one end of
the cable into the ADSL port (RJ-11 receptacle) on the rear panel of the Router and insert the other
end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instructions
included with the device or given to you by your service provider. The ADSL connection represents
the WAN interface. It is the physical link to the ISP’s network backbone and ultimately to the Internet.
Connect Router to Ethernet
The Router may be connected to any 10/100BASE-TX Ethernet LAN. Any connection to an Ethernet
concentrating device such as a switch or hub must operate at a speed of 10/100 Mbps only. When
connecting the Router to any Ethernet device that is capable of operating at speeds higher than
10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the connecting port.
Use standard twisted-pair cable with RJ-45 connectors. The RJ-45 port on the Router is a crossed port
(MDI-X). Follow standard Ethernet guidelines when deciding what type of cable to use to make this
connection. When connecting the Router directly to a PC or server use a normal straight-through cable.
You should use a crossed cable when connecting the Router to a normal (MDI-X) port on a switch or
hub. Use a normal straight-through cable when connecting it to an uplink (MDI-II) port on a hub or
switch.
The rules governing Ethernet cable lengths apply to the LAN to Router connection. Be sure that the
cable connecting the LAN to the Router does not exceed 100 meters.
Hub or Switch to Router Connection
Connect the Router to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through
cable as shown in the diagram below:
19
DSL-524T ADSL Router Manual
If you wish to reserve the uplink
port on the switch or hub for
another device, connect to any
on the other MDI-X ports (1x,
2x, etc.) with a crossed cable.
Computer to Router Connection
You can connect the Router
directly to a 10/100BASE-TX
Ethernet adapter card (NIC)
installed on a PC using the
Ethernet cable provided as
shown in this diagram.
Power On Router
To power on the Router:
1. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router
and plug the adapter into a suitable nearby power source.
2. You should see the Power LED indicator light up and remain lit. The Status LED should light solid
green and begin to blink after a few seconds.
3. If you have the Router connected to your network you can look at the Ethernet Link/Act LED
indicators to make sure they have valid connections. The Router will attempt to establish the
ADSL connection, if the ADSL line is connected and the connection is properly configured this
should light up after several seconds.
Factory Reset Button
The Router may be reset to the original factory default settings by depressing the reset button for a few
seconds while the device is powered on. Use a ballpoint or paperclip to push down the reset button.
Remember that this will wipe out any settings stored in flash memory including IP settings. The
factory default IP address of the Router is 192.168.1.1 and the subnet mask is 255.255.255.0.
20
DSL-524T ADSL Router Manual
3
Configuring the Router for the First Time
The first time you setup the Router it is recommended that you configure the WAN connection using a
single computer making sure that both the computer and the Router are not connected to the LAN.
Once the WAN connection is functioning properly you may continue to make changes to the Router
configuration including the IP settings. This chapter is concerned with using your computer to
configure the WAN connection. The following chapter describes the various menus used to configure
and monitor the Router including how to change IP settings. This chapter discusses the steps to first
establish the WAN connection. The remaining features, not directly concerned with establishing the
initial connection, are explained in Chapter 4, Web-based Management.
It is recommended that you install and configure the Router using one non-networked computer. This
allows you to verify that the ADSL service is functioning and that you are able to communicate with
the device. Once the initial ADSL connection is established, you can proceed to build an Ethernet
LAN around the device or incorporate it into an existing LAN.
WAN Configuration Summary
1. Connect to the Router To configure the WAN connection used by the Router it is first
necessary to communicate with the Router through its management interface, which is HTMLbased and can be accessed using a web browser. To access the management software your
computer must be able to “see” the Router. Your computer can see the Router if it is in the
same “neighborhood” or subnet as the Router. This is accomplished by making sure your
computer has IP settings that place it in the same subnet as the Router. The easiest way to
make sure your computer has the correct IP settings is to configure it to use the DHCP server
of the computer. The next section describes how to change the IP configuration for a computer
running a Windows operating system to be a DHCP client.
2. Configure the WAN Connection Once your are able to access the configuration software you
can proceed to change the settings required to establish the ADSL connection and connect to
the service provider’s network. There are different methods used to establish the connection to
the service provider’s network and ultimately to the Internet. You should know what
Encapsulation and connection type you are required to use for your ADSL service. It is also
possible that you must change the PVC settings used for the ADSL connection. Your service
provider should provide all the information you need to configure the WAN connection.
Configuring IP Settings on Your Computer
In order to configure your system to receive IP settings from the Router it must first have the TCP/IP
protocol installed. If you have an Ethernet port on your computer, it probably already has TCP/IP
protocol installed. If you are using Windows XP the TCP/IP is enabled by default for standard
installations. Below is an illustrated example of how to configure a Windows XP system to
automatically obtain IP settings from the Router. Following this example is a step-by-step description
of the procedures used on the other Windows operating systems to first check if the TCP/IP protocol
has been installed; if it is not, instructions are provided for installing it. Once the protocol has been
installed you can configure the system to receive IP settings from the Router.
For computers running non-Windows operating systems, follow the instructions for your OS that
configure the system to receive an IP address from the Router, that is, configure the system to be a
DHCP client.
21
DSL-524T ADSL Router Manual
Configure IP Settings
You must now enable your computer to access the Router’s configuration software. To do this you
will need to configure the IP settings on your computer. Follow these instructions to configure the IP
settings for the operating system installed on your computer.
Windows XP
1. In the Windows task bar, click the Start button, and then click Control Panel.
2. Double-click the Network Connections icon.
3. In the LAN or High-Speed Internet window, right-click on icon corresponding to your network
interface card (NIC) and select Properties. (This icon may be labeled Local Area Connection).
4. The Local Area Connection dialog box displays with a list of currently installed network items.
5. Make sure that the check box to the left of the item labeled Internet Protocol TCP/IP is
.
checked, and click
6. In the Internet Protocol (TCP/IP) Properties dialog box, click the button labeled Use the
following IP address:
7. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
8. Click
twice to confirm your changes, and close the Control Panel.
Windows 2000
First, check for the IP protocol and, if necessary, install it:
1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dial-up Connections icon.
3. In the Network and Dial-up Connections window, right-click the Local Area Connection icon,
and then select Properties.
4. The Local Area Connection Properties dialog box displays with a list of currently installed
network components. If the list includes Internet Protocol (TCP/IP), then the protocol has
already been enabled. Skip to step 3.
5. If Internet Protocol (TCP/IP) does not display as an installed component, click
6. In the Select Network Component Type dialog box, select Protocol, and then click
7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click
.
8. You may be prompted to install files from your Windows 2000 installation CD or other media.
Follow the instructions to install the files.
to restart your computer with the new settings.
9. If prompted, click
Next, configure IP information:
1. In the Control Panel, double-click the Network and Dial-up Connections icon.
2. In Network and Dial-up Connections window, right-click the Local Area Connection icon, and
then select Properties.
3. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP), and
then click
.
4. In the Internet Protocol (TCP/IP) Properties dialog box, click the button labeled Use the
following IP address:
5. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
6. Click
twice to confirm and save your changes, and then close the Control Panel.
22
.
.
DSL-524T ADSL Router Manual
Windows Me
In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.
Double-click the Network and Dial-up Connections icon.
In the Network and Dial-up Connections window, right-click on the Network icon, then select
Properties.
4. The Network Properties dialog box displays with a list of currently installed network
components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been
enabled. Skip to step 3.
1.
2.
3.
5.
If Internet Protocol (TCP/IP) does not display as an installed component, click
.
6.
7.
In the Select Network Component Type dialog box, select Protocol, and then click
Select Microsoft in the Manufacturers box.
8.
9.
Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click
.
You may be prompted to install files from your Windows Me installation CD or other media.
Follow the instructions to install the files.
.
10. If prompted, click
to restart your computer with the new settings.
Next, configure the IP information:
1. In the Control Panel, double-click the Network and Dial-up Connections icon.
2. In Network and Dial-up Connections window, right-click the Network icon, and then select
Properties.
3. In the Network Properties dialog box, select TCP/IP, and then click
.
4. In the TCP/IP Settings dialog box, click the Specify IP address option.
5. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
6. Click
twice to confirm and save your changes, and then close the Control Panel.
Windows 95, Windows 98 and Windows 98SE
1.
2.
3.
4.
First, check for the IP protocol and, if necessary, install it:
In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.
Double-click the Network icon.
The Network dialog box displays with a list of currently installed network components. If the
list includes TCP/IP, and then the protocol has already been enabled. Skip to step 2.
5.
6.
If TCP/IP does not display as an installed component, click
The Select Network Component Type dialog box displays.
7.
8.
9.
Select Protocol, and then click
.
The Select Network Protocol dialog box displays.
Click on Microsoft in the Manufacturers list box, and then click TCP/IP in the Network
Protocols list box.
.
10. Click
to return to the Network dialog box, and then click
again.
11. You may be prompted to install files from your Windows 95/98 installation CD. Follow the
instructions to install the files.
12. Click
to restart the PC and complete the TCP/IP installation.
Next, configure the IP information:
1. Open the Control Panel window, and then click the Network icon.
2.
Select the network component labeled TCP/IP, and then click
23
.
DSL-524T ADSL Router Manual
If you have multiple TCP/IP listings, select the listing associated with your network card or
adapter.
4. In the TCP/IP Properties dialog box, click the IP Address tab.
5. Click the Specify an IP address option.
6. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
3.
7.
8.
Click
twice to confirm and save your changes.
You will be prompted to restart Windows.
9.
Click
.
Windows NT 4.0
First, check for the IP protocol and, if necessary, install it:
In the Windows NT task bar, click the Start button, point to Settings, and then click Control
Panel.
3. In the Control Panel window, double click the Network icon.
4. In the Network dialog box, click the Protocols tab.
5. The Protocols tab displays a list of currently installed network protocols. If the list includes
TCP/IP, then the protocol has already been enabled. Skip to step 3.
1.
2.
6.
If TCP/IP does not display as an installed component, click
.
In the Select Network Protocol dialog box, select TCP/IP, and then click
.
You may be prompted to install files from your Windows NT installation CD or other media.
Follow the instructions to install the files.
9. After all files are installed, a window displays to inform you that a TCP/IP service called DHCP
can be set up to dynamically assign IP information.
7.
8.
10. Click
to continue, and then click
Next, configure the IP information:
1.
if prompted to restart your computer.
Open the Control Panel window, and then double-click the Network icon.
2. In the Network dialog box, click the Protocols tab.
.
3. In the Protocols tab, select TCP/IP, and then click
4. In the Microsoft TCP/IP Properties dialog box, click the Specify an IP address option.
5. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
Click
twice to confirm and save your changes, and then close the Control Panel.
Accessing the Configuration Manager
Now that your computer’s IP settings allow it to communicate with the Router, you can access the
configuration software.
Note: Be sure that the web browser on your computer is not configured to use a proxy server in
the Internet settings. In Windows Internet Explorer, you can check if a proxy server is enabled
using the following procedure:
1. In Windows, click on the Start button, go to Settings and choose Control Panel.
2. In the Control Panel window, double-click on the Internet Options icon.
3. Click the Connections tab and click on the LAN Settings button.
4. Verify that the “Use proxy server” option is NOT checked. If it is checked, click in the checked
box to deselect the option and click OK.
Alternatively you can access this Internet Options menu using the Tools pull-down menu in
Internet Explorer.
24
DSL-524T ADSL Router Manual
To use the web-based management software, launch a suitable web browser and direct it to the IP
address of the Router. Type in http:// followed by the default IP address, 192.168.1.1 in the address
bar of the browser. The URL in the address bar should read: http://192.168.1.1. Once entered, the user
will be prompted to enter the username and password to access the Configuration Manager, as show
below. A new window will appear and you will be prompted for a user name and password to access
the web-based manager. Use the default user name “admin” and password “admin” for first time setup.
You should change the web-based manager access user name and password once you have verified
that a connection can be established. The user name and password allows any PC within the same
subnet as the Router to access the web-based manger.
NOTE: Do not confuse the user name and password used to
access the web-based manager with the ADSL account user
name and password needed for PPP connections to access the
service provider’s network.
Figure 3-1. Enter Network Password dialog box.
Configure the Router with the Configuration Wizard
The first page that appears after you successfully login displays information about the Router’s Setup
Wizard. Tabs across the top of the screen show other available menus: Home, Advanced, Tools,
Status, and Help.
25
DSL-524T ADSL Router Manual
Figure 3-2. Home – Setup
When the Router is used to provide Internet access it actually must first access your service provider’s
network, that is, it must communicate with computers and other modems owned by your service
provider. These computers and modems then provide access to the Internet. The Router must be
configured to communicate with the systems that give it access to the larger network. The quickest
way for you to connect to the Internet is by using the Setup Wizard. Click the Run Wizard button
the following window will appear:
26
DSL-524T ADSL Router Manual
The Setup window has four options listed,
which will run through in the order given. Each
step will be explained in detail. Click Next to
access Step 1. You may click Back during the
Setup procedure to return to the previous
screen in the Setup Wizard, or Exit to exit the
Setup Wizard at any time during the
procedure.
Figure 3-3. Opening Setup window
Step 1: Choose Your Time Zone
In Step1, you must choose the time zone that
best corresponds to the area you are living in
by using the pull down menu. Choose the
appropriate setting and click Next to go on to
Step 2.
Figure 3-4. Choose Time Zone window
27
DSL-524T ADSL Router Manual
Step 2: Setting the ADSL Connection
Step 2 involves choosing the correct
connection type mode for your modem.
There are different methods or protocols
used to make this communication possible,
and both ends of the communication (you
and your ISP) must agree on what method
to use and how to set up the connection.
This is what you want to configure the
Router to do, to agree with the service
provider’s equipment and negotiate the
terms of the connection using a language
or protocol that both sides understand. This
window offers six connection types for the
user to choose from. The choice will
depend on information provided to you by
your ISP. Options available on the DSL524T are Dynamic IP Address, Static IP
Address, PPPoE/PPPoA and Bridge
Mode. Simply click the corresponding radio
button and click Next to go on to the
configuration window for that choice.
Figure 3-5. Set Internet Connection Type window
Step 2.1: Bridge Mode
Bridge Mode is for users who have software
on their computer or other network device to
accept the connection from your ISP. You
may change the PVC (Permanent Virtual
Channel) settings, which are defined by two
numbers, the VPI (Virtual Path Indicator) and
the VCI (Virtual Channel Indicator). These
two values should be provided to you by your
ISP. In most cases, the default settings are
correct and need not be altered. The second
setting is the Connection Type, selected by
using the pull-down menu. The two choices
available to the user here are 1483 Bridged
IP LLC and 1483 Bridged IP Vc-Mux, and
this correct choice should also be provided to
you by your ISP. After setting the values
listed, click the Next button to go to Step 3 of
the Configuration Wizard.
Figure 3-6. Set 1483 Bridged IP LLC
28
DSL-524T ADSL Router Manual
Step 3: Restart
In the following window, the user must restart
the system to save the settings implemented,
or go back to choose another option to
configure.
29
DSL-524T ADSL Router Manual
Step 2.2: Static IP Address
The following window is used to set the Static
IP mode for the Router. A Static IP address is
used whenever a known static IP is assigned.
The accompanying information such as the
Subnet mask, ISP Gateway Address and
DNS servers should also be specified in order
to be able to connect. These are the servers
would enable you to have access to other
web servers. Valid IP addresses range from
1.0.0.1 to 255.255.255.255.
To configure the connection for Static,
perform the steps listed below. Some of the
settings do not need to be changed the first
time the device is set up, but can be changed
later if you choose. After setting the values
listed, click the Next button to go to Step 3 of
the Configuration Wizard.
Figure 3-7. Set RFC2684 Bridged Static IP window
VPI/VCI
If you are told to change the VPI or VCI values, type in the values given
to you by your service provider. Many users will be able to use the
default settings.
IP Address
Enter the IP address based on the information provided to you by your ISP.
Subnet Mask
Enter the Subnet Mask based on the information provided to you by your ISP.
ISP Gateway
Address
Enter the Default Gateway based on the information provided to you by your ISP.
Primary DNS
Address
This entry is for the IP address of your primary domain name server, which should also
be provided to you by your ISP. The router will first try the Primary DNS Address to
resolve a website’s URL IP address. If this IP address fails, the router will then try the
Secondary DNS Address.
Secondary DNS
Address
The IP address of the secondary domain name server will be used to resolve a
website’s URL IP address if the Primary DNS Address fails. The information in this
field should also be provided by your ISP.
Connection Type
There are four Connection Types set in the router to be chosen by using the pull down
menu and they are 1483 Bridged IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP
LLC, 1483 Routed IP VC-Mux and IPoA. The correct choice should be told to you by
your ISP.
30
DSL-524T ADSL Router Manual
Step 3: Restart
In the following window, the user must restart
the system to save the settings implemented,
or go back to choose another option to
configure.
31
DSL-524T ADSL Router Manual
Step 2.3 Dynamic IP Address
Choosing the third option and clicking Next
will lead you to the following window to
configure the Router for. Users choosing this
option should have software located on their
computer or other networking device to
establish a connection between you and
your ISP. DHCP allows the user to set the
Router so it will automatically set IP
addresses for other devices on the LAN. For
this option, you may change the PVC
(Permanent Virtual Channel) settings, which
are defined by two numbers, the VPI (Virtual
Path Indicator) and the VCI (Virtual Channel
Indicator). These two values should be
provided to you by your ISP. In most cases,
the default settings are correct and need not
be altered. The second setting is the
Connection Type by using the pull-down
menu. The two choices available to the user
here are 1483 Bridged IP LLC and 1483
Bridged IP VcMux, and this correct choice
should also be provided to you by your ISP.
The Cloned MAC Address field is used to
copy the MAC Address of your Ethernet
Adapter to the router. Simply enter the MAC
Address into the space provided and click
the Clone Mac Address button. After
setting the values listed, click the Next
button to go to Step 3 of the Configuration
Wizard.
Figure 3-8. Set Dynamic IP Address
32
DSL-524T ADSL Router Manual
Step 3: Restart
In the following window, the user must restart
the system to save the settings implemented
or go back to choose another option to
configure.
33
DSL-524T ADSL Router Manual
Step 2:4 PPPoE/PPPoA
PPP or Point-to-Point protocol is a standard
method of establishing a network
connection/session between networked
devices. Different forms of PPP include
PPPoA and PPPoE, and they involve an
authentication process that requires a
username and password to gain access to
the network. PPPoE (Point to Point Protocol
over Ethernet), as described in RFC 2516, is
a method of using PPP through the Ethernet
network. PPPoA (Point to Point Protocol over
ATM) configuration requires the same basic
information as the previously discussed
PPPoE and both configuration menus are
identical. Notice the VPI and VCI values are
included.
To configure the connection for
PPPoE/PPPoA, perform the steps listed
below. Some of the settings do not need to
be changed the first time the device is set up,
but can be changed later if you choose. After
setting the values listed, click the Next button
to go to Step 3 of the Configuration Wizard.
VPI/VCI
Username &
Password
Connection Type
Figure 3-9. Set PPPoE window
If you are told to change the VPI or VCI values, type in the values
given to you by your service provider. Many users will be able to use
the default settings.
Type the Username and Password used to verify the identity of your
account. Typically, the Username is an account number assigned by
your ISP. See your ISP for further information.
Choose between PPPoE LLC, PPPoA LLC or PPPoE VC-Mux
depending on the instructions of your ISP.
34
DSL-524T ADSL Router Manual
Step 3: Restart
In the following window, the user must restart
the system to save the settings implemented
or go back to choose another option to
configure.
35
DSL-524T ADSL Router Manual
4
Home
This tab in the Web Manager will allow the user to set up various configurations in order to connect
your Router to the Internet. Much of the information necessary in these screens must be supplied to
you by your ISP. Remember to use the key words in bold when asking your ISP for information. This
will make your ISP’s job easier and therefore your configuration of the modem, much simpler and
quicker. Screens to configure under the Home tab include WAN, LAN, DHCP and DNS.
WAN Configuration
WAN is short for Wide Area Network. The WAN settings can be referred to as the Public settings. All
IP information in the WAN settings is public IP addresses, which is accessible on the Internet. There
are 8 PVCs pre-configured on this modem and upon initial connection, the appropriate settings should
automatically be set for you. Altering any of these fields should only be done if specified by your ISP,
who should have all the configuration settings necessary for your connection.
36
DSL-524T ADSL Router Manual
Figure 4- 1. Home – WAN window
ATM VC Setting
The first section of the WAN configuration pages offers fields to set general values for any Virtual
Channel chosen for connection to your ISP. This section holds the following fields to configure.
PVC: Leave this set at the default value 1 the first time the Router is set up. The modem has been preconfigured for 7 PVCs. The PVC for you should be enabled when you have made your first
connection to the Internet. The configured settings for this can be viewed under the Status tab, under
Device Info.
VPI: If instructed to change this, type in the VPI value for the initial connection.
VCI: If instructed to change this, type in the VCI value for the initial connection.
Virtual Circuit: This enables the PVC connection on your modem. Select Enable from the pull down
menu to enable the selected PVC.
WAN Settings
The WAN Settings section of this window will allows users to select the type of connection to be used
by the router to establish a connection between you and your ISP. Choosing a WAN type will change
37
DSL-524T ADSL Router Manual
the window and new settings will appear for the user to configure. The proper selection should be
given to you by your ISP.
Dynamic IP Address
Selecting this option in the WAN Settings will change your screen to look like the one seen below.
Users choosing this option should have software located on their computer or other networking device
to establish a connection between you and your ISP. The Connection Type is chosen by using the pulldown menu. The two choices available to the user here are 1483 Bridged IP LLC and 1483 Bridged
IP Vc-Mux, and this correct choice should also be provided to you by your ISP. The Cloned MAC
Address field is used to copy the MAC Address of your Ethernet Adapter to the router. Simply enter
the MAC Address into the space provided and click the Clone Mac Address button. The Maximum
Transmission Unit (MTU) is a link layer restriction on the maximum number of bytes of data in a
single transmission. The default size is 1400 bytes per packet. NAT improves network security in
effect by hiding the private network behind one global and visible IP address. NAT address mapping
can also be used to link two IP domains via a LAN-to-LAN connection. To enable NAT on the Router,
use the pull-down menu and select Enabled. The Firewall allows the Router to enforce policies to
protect against certain kinds of attacks. To enable the firewall on the Router, use the pull-down menu
and select Enabled.
Figure 4- 2. WAN Settings window for Dynamic IP Address
Click Apply to set the Dynamic IP settings for your DSL-524T.
38
DSL-524T ADSL Router Manual
Static IP Address
Selecting this option in the WAN Settings will change your screen to look like the one seen below. A
Static IP address is used whenever a known static IP is assigned. The accompanying information such
as the Subnet mask, ISP Gateway Address and DNS servers should also be specified in order to be
able to connect. These are the servers would enable you to have access to other web servers. Valid IP
addresses range from 1.0.0.1 to 255.255.255.255. All information to be entered in this window must
be provided to you by your ISP.
Figure 4- 3. WAN Settings window for Static IP Address
This window holds the following fields for the user to configure.
Connection Type
This field allows the user to choose the connection type used to connect your router
to your ISP. The user may choose between 1483 Bridged IP LLC, 1483 Bridged IP
VC-Mux, 1483 Routed IP LLC and 1483 Routed IP VC-Mux. The correct choice
should be told to you by your ISP.
IP Address
Enter the IP address based on the information provided to you by your ISP.
Subnet Mask
Enter the Subnet Mask based on the information provided to you by your ISP.
Gateway Address
Enter the Default Gateway based on the information provided to you by your ISP.
39
DSL-524T ADSL Router Manual
Primary DNS
Address
This entry is for the IP address of your primary domain name server, which should
also be provided to you by your ISP. The router will first try the Primary DNS
Address to resolve a website’s URL IP address. If this IP address fails, the router
will then try the Secondary DNS Address.
Secondary DNS
Address
The IP address of the secondary domain name server will be used to resolve a
website’s URL IP address if the Primary DNS Address fails. The information in this
field should also be provided by your ISP.
MTU
The Maximum Transmission Unit (MTU) is a link layer restriction on the maximum
number of bytes of data in a single transmission. The default size is 1400 bytes per
packet.
NAT
NAT improves network security in effect by hiding the private network behind one
global and visible IP address. NAT address mapping can also be used to link two IP
domains via a LAN-to-LAN connection. Use the pull-down menu to Enable or Disable
NAT on the Router.
Firewall
The Firewall allows the Router to enforce policies to protect against certain kinds of
attacks. To enable the firewall on the Router, use the pull-down menu and select
Enabled.
Click Apply to set the Static IP address for the DSL-524T.
40
DSL-524T ADSL Router Manual
PPPoE/PPPoA
Selecting this option in the WAN Settings will change your screen to look like the one seen below.
PPP or Point-to-Point protocol is a standard method of establishing a network connection/session
between networked devices. Different forms of PPP include PPPoA and PPPoE, and they involve an
authentication process that requires a username and password to gain access to the network. PPPoE
(PPP over Ethernet), as described in RFC 2516, is a method of using PPP through the Ethernet
network. PPPoA (PPP over ATM) configuration is over ATM and requires the same basic information
as the previously discussed PPPoE. Both configuration menus are identical.
To configure the connection for PPPoE/PPPoA, perform the steps listed below. Some of the settings
do not need to be changed the first time the device is set up, but can be changed later if you choose.
Figure 4- 4. WAN Settings window for PPoE/PPoA
Username &
Password
Type the Username and Password used to verify the identity of your
account. Typically, the Username is an account number assigned by
your ISP. See your ISP for further information.
41
DSL-524T ADSL Router Manual
Connection Type
MTU
MRU
Default Route
NAT
Firewall
IP Control
Static IP
Choose between PPPoE LLC, PPPoA LLC or PPPoE VC-Mux, depending
on the instructions of your ISP.
The Maximum Transmission Unit (MTU) is a link layer restriction on the
maximum number of bytes of data that can be sent in a single transmission.
The default size is 1400 bytes per packet.
The Maximum Receive Unit (MRU) field indicates the maximum number of
bytes that can be received by the Router. This MRU’s default size is 1492
bytes per packet. Upon initial negotiation with your ISP, the router will tell
the ISP that the amount entered here is the largest packet allowed to be
accepted by the router.
Click the corresponding radio button if you wish to enable or disable the
Default Route. The Default Route is used for outgoing packets, which have an
unresolved IP address. If the router is unable to match the destination address
on a received packet with a destination address in the routing table, the router
uses the default route.
NAT improves network security in effect by hiding the private network
behind one global and visible IP address. NAT address mapping can also be
used to link two IP domains via a LAN-to-LAN connection. Use the pulldown menu to Enable or Disable NAT on the Router.
The Firewall allows the Router to enforce policies to protect against certain
kinds of attacks. To enable the firewall on the Router, use the pull-down
menu and select Enabled.
This field allows the user to control the WAN IP address of the router. There
are three choices for the user:
Dynamic IP – Select this option if you wish to have an IP address
automatically assigned to the router.
Unnumbered IP – Select this option if your ISP has assigned a block of IP
addresses for use.
Static IP – Select this option if you know the IP address assigned to the
router. After selecting this option, the user must enter the known Static IP
address in the following field. A Static IP address is used whenever a known
static IP is assigned.
This field states the Static IP Address of the Router and can only be
configured when Static IP is chosen in the previous field.
Click Apply to implement the PPPoE settings for the DSL-524T.
Bridge Mode
Selecting this option in the WAN Settings will change your screen to look like the one seen below.
Bridge Mode is for users who have software on their computer or other network device to accept the
connection from your ISP. The Connection Type setting is selected by using the pull-down menu.
The two choices available to the user here are 1483 Bridged IP LLC and 1483 Bridged IP Vc-Mux,
and this correct choice should be provided to you by your ISP.
42
DSL-524T ADSL Router Manual
Figure 4- 5. WAN Settings window for Bridge Mode
Click Apply to implement the Bridge Mode settings for the DSL-524T.
ATM
This section of the WAN window allows the user to adjust ATM Quality of Service (QoS) or traffic
parameters to suit specific traffic requirements. For applications or circumstances where packet loss or
packet delay are a concern, ATM QoS can be adjusted to minimize problems. For most accounts, it
will not be necessary to change these settings. Altering QoS settings can adversely affect performance
of some commonly used Internet applications.
If you plan to change QoS or traffic parameters, contact your ISP or network services provider for
information on what types of adjustment are available or possible for your account. Your ISP may not
support the class of service you want to use.
Figure 4- 6. ATM settings for the WAN interface
Service Category: This field represents the QoS (Quality of Service) feature for the modem. The
choices available from the pull down menu include UBR (Unspecified Bit Rate), CBR (Constant Bit
Rate) and VBR (Variable Bit Rate). These values should already be set for you and should not be
changed unless specified by your ISP.
• UBR – Unspecified Bit Rate, this is the default category used for general-purpose Internet traffic
where normal levels of packet loss and delay are acceptable. For some applications or for multiple
connection accounts, it may be desirable to specify the PCR.
43
DSL-524T ADSL Router Manual
•
CBR – Constant Bit Rate, usually used in circumstances where very low packet loss and very low
Cell Delay Variable (CDV) are desirable.
• VBR – Variable Bit Rate, usually used when network traffic is characterized by bursts of packets
at variable intervals, and some moderate packet loss and delay is acceptable. This category is
typically used for audio and video applications such as teleconferencing. The network must
support QoS Class 2 to use VBR.
PCR: PCR (Peak Cell Rate) refers to the Bandwidth control on your modem. This field allows you to
enter a value representing the maximum bps (bits per second) the modem can receive. This field is
limited by the stream coming form your ISP.
SCR: SCR (Sustained Cell Rate) refers to the Bandwidth control on your modem. This field allows
you to enter a value representing the minimum bps (bits per second) the modem can receive. After
making the changes to this screen, click Apply to let your changes take effect.
44
DSL-524T ADSL Router Manual
LAN Configuration
LAN is short for Local Area Network. This is considered your internal network. These are the IP
settings of the LAN interface for the DSL-524T and may be referred to as Private settings. You may
change the LAN IP address if needed. The LAN IP address is private to your internal network and
cannot be seen on the Internet.
IP Address: The IP address of the LAN interface. The default IP address is 192.168.1.1.
Subnet Mask: The subnet mask of the LAN interface. The default subnet mask is 255.255.255.0.
Figure 4- 7. LAN Settings window
Click Apply to implement changes made to this window.
45
DSL-524T ADSL Router Manual
DHCP
Dynamic Host Configuration Protocol (DHCP) allows the gateway to automatically obtain the IP
address from a DHCP server on the service provider’s network. The service provider assigns a global
IP address from a pool of addresses available to the service provider. Typically the IP address assigned
has a long lease time, so it will likely be the same address each time the Router requests an IP address.
If DHCP is not enabled on the Router, it is necessary for the user to assign a static IP address at each
computer on your LAN.
46
DSL-524T ADSL Router Manual
Figure 4- 8. DHCP configuration window
To setup DHCP for your LAN, first enable the Router as a DHCP server by clicking the corresponding
DHCP Server radio button in the window above and enter the Starting IP Address and Ending IP
address to create a pool of IP addresses to be assigned to other end nodes (computers, routers, etc.) on
47
DSL-524T ADSL Router Manual
the LAN. The Lease Time field is the time the Server will set for devices using DHCP to re-request an
IP Address. When using the Router in DHCP mode you may also configure DNS settings for the LAN.
Click the DNS Mode radio button to auto to allow the Router to automatically relay DNS settings to
properly configured DHCP clients. Click Manual to manually enter the Primary and Secondary DNS
IP addresses. When the Router has been enabled as DHCP Server the administrator of the server can
assign a Static IP address to each computer on the LAN from the workstation where the DCHP server
has been enabled. To assign a Static IP address to a computer on the LAN, enter the IP and MAC
address in the Static IP Assignment field. Click Apply to implement information set in this table.
48
DSL-524T ADSL Router Manual
DNS
DNS or Domain Name Server is a system that translates Domain Names into IP addresses. Setting up
a DNS will allow the router to contact the DNS to ask it to translate and find a web site you have
entered. The following window allows you to set two DNS servers by their IP addresses and these IP
addresses should be supplied to you by your ISP.
Figure 4- 9. DNS window
To configure the DNS for the Router, use the DNS Relay Selection pull down menu to select the DNS
configuration for the router. There are three choices:
• Disable DNS – Selecting this option will disable the DNS function of your router.
• Use Auto Discovered DNS Server Only – This choice will enable the router to automatically
find the DNS Server for your setup.
• Use User Discovered DNS Server Only – This choice will enable the DNS Servers entered in
the Preferred DNS Server and Alternate DNS Server fields. These two IP addresses must be stated
to you by your ISP.
49
DSL-524T ADSL Router Manual
The router will first try the Preferred DNS Server to resolve a website’s URL IP address. If that IP
address fails to resolve the URL, the Router will then try the Alternate DNS Server. Your ISP must
provide this information to you. Click Apply to set the DNS configurations into the memory of the
Router.
Dynamic DNS
The Router supports DDNS, a service that maps Internet domain names to IP addresses. DDNS serves
a similar purpose to DNS in that DDNS allows anyone hosting a Web or FTP server to advertise a
public name to prospective users. Unlike DNS that only works with static IP addresses, DDNS works
with dynamic IP addresses, such as those assigned by an ISP or other DHCP server. DDNS is popular
with home networkers, who typically receive dynamic, frequently-changing IP addresses from their
service provider. To use DDNS, one simply signs up with a provider and installs network software on
their host to monitor its IP address. Please see your ISP for further information.
Figure 4- 10. Dynamic DNS window
50
DSL-524T ADSL Router Manual
5
Advanced Configuration
The Advanced tab has ten windows for you to view and configure, which are UpnP, Virutal Server,
LAN Clients, SNMP, Filters, Bridge Filters, Routing, DMZ. Firewall, RIP, PPP, ADSL, and
ATM VCC, and QoS.
UPnP
UPnP supports zero-configuration networking and automatic discovery for many types of networked
devices. When enabled, it allows other devices that support UPnP to dynamically join a network,
obtain an IP address, convey its capabilities, and learn about the presence and capabilities of other
devices. DHCP and DNS service can also be used if available on the network. UPnP also allows
supported devices to leave a network automatically without adverse effects to the device or other
devices on the network.
UPnP can be supported by diverse networking media including Ethernet, Firewall, phone line and
power line networking.
51
DSL-524T ADSL Router Manual
Figure 5- 1. UPnP window
To enable UPnP for any available connection, click to check the Enable UPnP selection box, select
the connection or connections on which you will enable UPnP listed under Available Connections
and click the Apply button.
Virtual Server
To view the following window, click on the Advanced tab at the top of the window and then click the
Virtual Server button to the left. The Virtual Server will allow remote users access to various
services outside of their LAN through a public IP address, such as FTP (File Transfer Protocol) or
52
DSL-524T ADSL Router Manual
HTTPS (Secure Web). Select a connection type and enter an IP address for the virtual server. After
configuring the Router for these features, the Router will redirect these external services to an
appropriate server on the users’ LAN. To choose a particular service click a radio button from the
category list and highlight the service from the Available Rules list. Click Add, and then reboot to
apply the rule.
Figure 5- 2. Virtual Server window
53
DSL-524T ADSL Router Manual
LAN Clients
The LAN Clients menu is used when establishing Port Forwarding, Access Control and Advanced
Security rules for IP addresses on the LAN. This menu can be accessed directly by clicking on the
LAN Clients button or hyperlink in the Advanced setup menu. You can also click on the New IP
button located in the Port Forwarding, Access Control and Advanced Security menus to access this
menu. In order to use these advanced features it is necessary to have IP addresses available for
configuration. If there are no IP addresses listed in the LAN Clients menu, it will not be possible to
configure Port Forwarding, Access Control and Advanced Security. Use the LAN Clients menus to
add or delete static IP addresses for the advanced functions mentioned above, or to Reserve a
Dynamically assigned IP address for an advanced function. Dynamically assigned IP addresses will
only be listed if DHCP is enabled on the Router.
54
DSL-524T ADSL Router Manual
Figure 5- 3. LAN Clients window
To add a static IP address to the list of available IP addresses, type an IP address that falls within the
range a available IP addresses and click on the Add button. In the example above, available addresses
range from 10.0.0.1 to 10.255.255.254. Any addresses added will appear in the list of Static
Addresses available for advanced configuration. These addresses can then be used in the other Port
Forwarding, Access Control and Advanced Security menus. To delete an IP address from the list of
Static Addresses, click the Delete box for the address or addresses you want to eliminate and click on
the Apply button.
55
DSL-524T ADSL Router Manual
Dynamically assigned IP addresses may be reserved so that the LAN IP address for the device does
not expire. This will create a permanent entry for the device in the ARP table and in effect, it becomes
a static IP address. Click to check the Reserve box for the address or addresses you want to reserve
and click the Apply button. These reserved addresses will no longer be available for DHCP
assignment and will be listed in the Static IP Addresses table.
SNMP
This menu can be accessed directly by clicking on the SNMP button or hyperlink in the Advanced
setup menu. Simple Network Management Protocol (SNMP) is an OSI Layer 7 Application designed
specifically for managing and monitoring network devices. SNMP enables network management
stations to read and modify the settings of gateways, routers, switches, and other network devices.
Use SNMP to configure system features for proper operation, performance monitoring, and detection
of potential problems in the Router or network.
56
DSL-524T ADSL Router Manual
Figure 5- 4. SNMP window
Under SNMP Management, enable or disable SNMP Agent or SNMP Traps by using the check
boxes. An SNMP Agent is software that runs locally on the device. A defined set of variables
(managed objects) is maintained by the SNMP agent and used to manage the device. Traps are
messages that alert network personnel of events that occur on the Switch. The events can be as serious
as a reboot (someone accidentally turned OFF the Switch), or less serious like a port status change.
The Router generates traps and sends them to the trap recipient (or network manager). Typical traps
include trap messages for Authentication Failure, Topology Change and Broadcast/Multicast Storms.
In the Name, Location and Contact fields, enter the appropriate information of the Network
Administrator. Under Community, enter the name of an SNMP community string that defines the
57
DSL-524T ADSL Router Manual
relationship between the SNMP manager and an agent. The community string acts like a password to
permit or deny access to an agent on the Router. The defining characteristic associated with the
community string is the Access Right. The agent’s access right can be set as either read/write or readonly. Under Traps enter the Destination IP address and Trap Community Name so that the agent
sends traps to the management server. The Trap Version can also be set to either SNMP V1 (to
specify that SNMP version 1 will be used) or SNMPv2c, which supports both centralized and
distributed network management strategies. SNMP V2c includes improvements in the Structure of
Management Information (SMI) and adds some security features.
Filters
The following window will aid the router’s administrator in configuring filters for IP addresses. There
are two types of filters that the administrator can configure. Outbound Filters are for administrators
who wish to deny clients on their LAN from accessing certain virtual ports or IP addresses on the
Internet. Inbound Filters are for administrators who wish to deny IP addresses or virtual ports from
outside the router (on the Internet) from accessing the Internal LAN of the router. Click the
corresponding radio button to configure Outbound or Inbound Filters. Both screens are identical in
configuration.
58
DSL-524T ADSL Router Manual
Figure 5- 5. Filters window
To configure filters for the router, configure the folowing fields and click Apply.
Source IP
Enter an IP address or range of addresses from which to block or allow packets. This
field may also be used to block a set of subnet masks by using the corresponding pull
down menu.
Destination IP
Enter an IP address or range of addresses to which to block or allow packets from being
sent. This field may also be used to block a set of subnet masks by using the
corresponding pull down menu.
Source Port
Enter a port or range of ports from which to block or allow packets. This field can only
be configured if TCP or UDP is selected in the Protocol field. The Safe Range option in
59
DSL-524T ADSL Router Manual
the pull down menu is for ports that have a higher value than 1024.
Destination Port
Enter a port or range of ports to which to block or allow packets from being sent. This
field can only be configured if TCP or UDP is selected in the Protocol field. The Safe
Range option in the pull down menu is for ports that have a higher value than 1024.
Protocol
Use the pull down menu to select the protocol type to be used for this filter. The user
may choose between TCP, UDP or TCP UDP.
Action
This field states allows the user to choose the course of action for this filter to take. The
user may choose Allow to allow packets to be forwarded to end nodes configured in the
previous fields. The user may choose Deny to block packets from being forwarded to
end nodes configured in the previous fields.
Properly configured filters for the router will appear in the table in the bottom half of the filters
window. Click Apply to set the filters configured for this router.
Bridge Filters
Bridge filters are used to block or allow various types of packets through the WAN interface. This
may be done for security or to improve network efficiency. The rules are configured for individual
devices based on MAC address. Filter rules can be set up for source, destination or both. You can set
up filter rules and disable the entire set of rules without loosing the rules that have been configured.
60
DSL-524T ADSL Router Manual
Figure 5- 6. Bridge Filters window
To add a bridge filter rule, check Enable Bridge Filters, type in a Source MAC, a Destination MAC
or both in the entry fields. Select Any to apply the rule to any protocol that the router receives. The
user may also specify a protocol to be filtered by using the pull-down menu, and then choose either
Allow, to allow the specified protocol to pass through the router, or Deny to filter the protocol from the
router. The protocols that may be specifically allowed or denied to pass through the WAN interface
are IPv4, IPv6, RARP, PPPoE Discovery and PPPoE Session. Click the Add button. The rule will
appear in the entry field below as it is currently configured. To edit an existing rule, select the rule by
clicking the corresponding Edit radio button. Make the desired changes and click the Add button. To
61
DSL-524T ADSL Router Manual
remove a bridge filter from the table in the bottom half of the window, click to select the
corresponding Delete box, and then click Apply. Remember to save the configuration changes.
Routing Table
Clicking the Routing tab will lead you to this window, which is used to manually enter a routing entry
for the Router. Routing entries are used when known gateways and hops on the network are known to
the user. Unless instructed by your ISP or if you have a greater knowledge of networking, this window
should not be necessary to configure as the LAN IP settings should be sufficient for your connection.
Figure 5- 7. Routing Table window
62
DSL-524T ADSL Router Manual
The user may configure the following fields for Static routing on the router:
Destination
Enter the host IP address or the remote network that will be used for static routing on
the router.
Netmask
Enter the Subnet Mask to be used for static routing.
Gateway
Enter the gateway device’s IP address. This is an IP address of a device that will
allow the user to contact the remote network or Host IP address. This field cannot be
configured or used if the following field, Connection, has been selected.
Connection
Choose a PVC from the corresponding pull-down menu to be used for static routing.
This field cannot be configured or used if the previous field, Gateway, has been
selected.
Click Apply to set the routing information configured.
63
DSL-524T ADSL Router Manual
DMZ
Firewalls may conflict with certain interactive applications such as video conferencing or playing
Internet video games. For these applications, a firewall bypass can be set up using a DMZ IP address.
The DMZ IP address is a “visible” address and does not benefit from the full protection of the firewall
function. Therefore it is advisable that other security precautions be enabled to protect the other
computers and devices on the LAN. It may be wise to use isolate the device with the DMZ IP address
from the rest of the LAN. For example, if you want to use video conferencing and still use a firewall,
you can use the DMZ IP address function. In this case, you must have a PC or server through which
video conferencing will take place. The IP address of this PC or server will then be the DMZ IP
address. You can designate the server’s IP address as the DMZ by typing in the IP address in the IP
Address space provided and then enabling its status by clicking the Status Enabled radio button and
then click Apply. For the system that uses the DMZ IP address, you may want to manually assign an
IP address to it and adjust your DHCP server addresses so that the DMZ IP address is not included in
the DHCP server range. This way you avoid possible IP address problems if you reboot the DMZ
system. To configure the Router’s DMZ IP address, click the Advanced tab at the top of the screen
and then the DMZ tab to the left.
64
DSL-524T ADSL Router Manual
Figure 5- 8. DMZ window
Click Apply when your configuration is complete.
65
DSL-524T ADSL Router Manual
Firewall
The DSL-524T ADSL Router comes equipped with a firewall. The Firewall configuration screen
allows the Router to enforce specific predefined policies intended to protect against certain common
types of attacks. To configure the Router’s firewall, click the Advanced tab at the top of the screen
and then the Firewall tab to the left.
Figure 5- 9. Firewall window
66
DSL-524T ADSL Router Manual
This window has three filtering options for you to choose, DoS (Denial of Service) Protection, Port
Scan Protection and Service Filtering. DoS Protection and Port Scan Protection may be globally
enabled on the router and then may be modified to the users preference by checking the boxes in these
sections. For Service Filtering, the user must choose which services to be filtered by the router using
the corresponding check boxes. The user may choose any combination of these to use for firewalling.
Click Apply to set these firewall rules to the routers memory.
67
DSL-524T ADSL Router Manual
RIP
The DSL-524T supports RIP v1 and RIP v2 used to share routing tables with other Layer 3 routing
devices on the LAN, at your ISP’s location or remote networks connected to your network through the
ADSL line. The user may enable or disable RIP v1 (received and sent) or RIP v2. This will enable the
router to send and receive RIP packets. Disabling the RIP function will disable the routing function of
this device.
Figure 5- 10. RIP window
68
DSL-524T ADSL Router Manual
To configure RIP, first use the RIP pull-down menu to enable RIP on the Router. Then select the
protocol to be used by using the pull-down menu. The choices are RIP v1, RIPv1 Compatible and
RIP v2. Then the user must choose the direction by selecting In, Out or Both. After making the
configuration choices for RIP, click the Apply button to set the configurations in the memory of the
Router.
PPP
The following window is for users employing the PPP protocol as their connection to the ISP. This
window will be specific to PVCs previously configured and will display information concerning the
PVC selected in the WAN configuration window.
69
DSL-524T ADSL Router Manual
Figure 5- 11. PPP window
The window above displays the following information.
PVC
Displays the PVC currently in use on the Router. This router can be configured
for eight PVCs.
Connection State
Displays the connection state of the PVC displayed above.
Connection Setting
This field has three options for the connection setting of the PPP protocol.
•
Always On – Clicking this radio button will set the connection to always be
connected.
•
Connection on Demand – Clicking this radio button will set the Router to
70
DSL-524T ADSL Router Manual
connect to the Internet only when requested to by your computer.
•
ATM VCs List
Manual – Clicking this radio button will set the router to only connect when
the user clicks the connect button in the previous field.
This field will display the status of PVCs currently in use on the Router.
Click Apply to set the changes in the memory of the Router.
ADSL
This window will allow you to set the ADSL configuration protocol for the modem. You may choose
the modulation type from the pull-down window. The options are Multi-mode, T1.413, G.Dmt and
G.lite. Your ISP must provide this information to you. Click Apply after you have made the proper
selection.
71
DSL-524T ADSL Router Manual
Figure 5- 12. ADSL window
72
DSL-524T ADSL Router Manual
ATM VCC
The ATM VCC window shows you the current WAN settings implemented on your modem under the
heading ATM VCs List at the bottom of the screen. Selecting a Connection Type will change the
window for the values for the Connection setting selected. These values have already been described
in the WAN Configuration section of the Home setup. Click Apply to set changes into the Router’s
memory.
Figure 5- 13. ATM VCC window
73
DSL-524T ADSL Router Manual
QoS
QoS is an implementation of the IEEE 802.1p standard that allows network administrators a method of
reserving bandwidth for important functions that require a large bandwidth or have a high priority,
such as VoIP (voice-over Internet Protocol), web browsing applications, file server applications or
video conferencing. Not only can a larger bandwidth be created, but other less critical traffic can be
limited, so excessive bandwidth can be saved. Each physical port on the Router can have up to 8
PVCs (Permanent Virtual Circuits) to which traffic from various sources can be mapped to, and in
turn prioritized. Select a PVC that has been configured (to configure a PVC click Home > WAN), and
then assign a Priority of 1 (low) to 4 (high). To enable QoS settings click the Enable Port Based
QoS check box. To enable IGMP Snooping/Proxy on a particular PVC click on the PVC and then
click the radio button to Enabled.
74
DSL-524T ADSL Router Manual
Figure 5- 14. QoS window
75
DSL-524T ADSL Router Manual
6
Tools
The Tools tab allows you to set up basic maintenance features on the modem. The windows available
under this tab include Admin, Time, System, Firmware, and Test.
Admin
The Admin window allows you to configure a new password for the modem. There is only one
administrator account that can access the DSL-524T’s web management interface. To change the
password, first enter the Old Password in its respective field, then enter the password into the New
Password field and repeat the password in the Confirm Password field. Click Apply to set your new
password.
This wildow will also allow the user to enable remote management of the device from a remote
computer, either through the web management or through Telnet. To configure this function, click the
Enabled radio button under the Remote Management heading, enter the IP Address of the computer
you wish to allow to remotely configure the Router, along with the corrsponding SubnetMask
(Netmask). Click Apply to set these configurations into the memeory of the Router.
76
DSL-524T ADSL Router Manual
Figure 6- 1. Administrator Settings window
Time
The system time is the time used by the DSL-524T for scheduling services. You can manually set the
time, connect to a NTP (Network Time Protocol) server or synchronize the time on the router with
your PC. If an NTP server is set, you will only need to set the time zone (in the set up wizard). You
may also set the time from the clock on your computer by checking the corresponding radio button. To
manually set the time, you will need to input the value into the fields provided. Click Apply to set
changes made.
77
DSL-524T ADSL Router Manual
Figure 6- 2. Time window
Remote Log
Us the Remote Log menu to set up logging to servers or computers that are located outside the LAN or
subnet of the Router.
78
DSL-524T ADSL Router Manual
Figure 6- 3. Remote Log
Select the Log Level from the pull-down menu. The levels available are: Alert, Critical, Debug, Error,
Info, Notice, Panic and Warning. Type in the IP address of a receiver for the log message in the Add
an IP Address field and click on the Add button. Log message receivers that are added appear listed
in the Select a logging destination pull-down menu. These may be used at any time for other types of
log messages. To remove a log message receiver from the list, select it and click on the Remove
button. Click the Apply button when you have configured the log message receivers. Remember to
save the settings to non-volatile memory.
79
DSL-524T ADSL Router Manual
System
This window offers four settings for the user to configure. The user may save the settings configured
on the router by clicking the Save button. A file Download dialogue box will appear questioning the
user where to save the files on your computer. Files will be saved as XML documents. The user may
also upload save settings by using the Load Settings From Local Hard Drive field by entering the
path of the file on your computer into the box. If you are not sure of the path, click Browse to find the
file on your computer. Click Load to initiate the file transfer. Next, click save and reboot. You may
reset the ADSL Router back to factory settings by clicking on Restore.
Figure 6- 4. System Settings window
80
DSL-524T ADSL Router Manual
Firmware
You can upgrade the firmware of the ADSL Router at this page. Make sure the firmware you want to
use is on the local hard drive of the computer. Click on Browse to browse the local hard driver and
locate the firmware to be used for the update. Once found, click Apply to initiate the transfer. Please
check the D-Link support site for firmware updates at D-Link Technical support website of your
country. Remember to restart the Router after uploading new firmware.
Figure 6- 5. Firmware Upgrade window
81
DSL-524T ADSL Router Manual
Miscellaneous
The Ping Test menu allows you to ping any IP address from the Router to test connectivity to the
address. To Ping a device, enter the IP address of the device that you wish to ping into the Ping IP
Address field and click Ping to start the Ping mechanism. The results of the ping will be shown under
the Ping Result heading. Click Apply to set changes made in this page.
Figure 6- 6. Miscellaneous window
Test
The Diagnostics window allows users to test the functionality of the router by executing a series of
tests. This window will aid the user in troubleshooting various problems that may occur with the
functionality of the router. This window will appear differently depending on connection type chosen.
The following picture shows the window that includes all possible connection tests associated with
this Router.
82
DSL-524T ADSL Router Manual
Figure 6- 7. Diagnostics window
To perform the following tests, choose the PVC (Private Virtual Connection) that you wish to test and
click Apply. Test results will either be displayed as Pass or Fail. The following tasks will be
performed:
Testing Ethernet
LAN Connection
This test will check the Ethernet connection of your Router.
Testing ADSL
Synchronization
This test will check the ADSL line connected to your Router.
Testing ATM
OAM segment
ping
This test will check the PVC connectivitiy by sending out an OAM
(Operation Administration Management) packet. If the remote device
on this segment returns the ping packet, the PVC has passed the test
and a Pass result will appear.
This test will check the PVC connectivitiy by sending out an OAM
(Operation Administration Management) packet. If the remote device
returns the ping packet, the PVC has passed the test and a Pass result
will appear.
This test will check to see if the Primary DNS is accessible from the
Testing ATM
OAM end to end
ping
Ping Primary
83
DSL-524T ADSL Router Manual
Domain Name
Server
Router.
Ping
www.dlink.com
This test wil check to see if the D-Link website can be pinged from
the Router.
84
DSL-524T ADSL Router Manual
7
Status
The Status tab will allow users to check information about the Router, including Device Information,
Log, Stats and the ADSL line.
Device Info
The device info window, located under the Status tab will allow users to view information regarding
the settings of the Router, both on the LAN side and WAN side of the connection.
Figure 7- 1. Device Info window
85
DSL-524T ADSL Router Manual
The following information is what is displayed in the Device Info window:
LAN
MAC Address
IP Address
Subnet Mask
DHCP Server
NAT
Displays the MAC Address of the Router.
Displays the current IP address of the Device.
Displays the Subnet Mask of the device.
Displays the DHCP status implemented on the Router.
Displays the current NAT staus implemented on the Router.
WAN Channel
Virtual Circuit
Status
Connection
Type
IP Address
Subnet Mask
Default
gateway
DNS Server
Displays the number of the Private Virtual Channel located on the
Router.
Displays the connection status of the selected Virtual Channel.
Displays the connection type employed on this Virtual Circuit.
Displays the IP address of the corresponding Virtual Circuit.
Displays the Subnet mask of the corresponding Virtual Circuit.
Displays the Default gateway of the corresponding Virtual Circuit.
Displays the DNS Server currently employed on this Virtual
Circuit.
86
DSL-524T ADSL Router Manual
DHCP
The DHCP Clients window, located under the Status tab will allow users to view information
regarding the DHCP Clients on the Router.
Figure 7- 2. DHCP Clients
87
DSL-524T ADSL Router Manual
Log
The Log window allows users to view events occurring within the Router by time and date. To clear
the log events, click Clear Log. To save the log, click Save Log and a pop-up window will appear to
find a folder on your computer to save the log files to.
Figure 7- 3. Device Log window
88
DSL-524T ADSL Router Manual
Statistics
The Stats window will allow users to view transmiited and received packets occuring on the Router,
both for the Ethernet connection and for the ADSL connection. To choose a interface to view statistics
for, click the corresponding radio button for either ADSL or Ethernet, which will subsequentially
change the Statistics screen, as shown below. To refresh the stats in this window, click Refresh.
Figure 7- 4. Stats window for Ethernet
Figure 7- 5. Statistics window for ADSL
89
DSL-524T ADSL Router Manual
ADSL
The ADSL Line window, located under the Status tab, will allow users to monitor the speed of the
upstream and downstream packet flow of the Router.
Figure 7- 6. Status ADSL window
The following information is displayed:
ADSL Firmware
Version
The current Firmware version currently set in the Router.
ADSL Software
Version
The current Software version currently set in the Router.
Line state
Displays the current line state of the ADSL connection, either being Up or
Down.
Modulation
Displays the modullation type currently set on the router for the ADSL
connection.
Annex mode
This field displays the ADSL annex modes for Annex A or Annex B.
90
DSL-524T ADSL Router Manual
Max Tx Power
This field displays the transmit output power level of the CPE.
SNR Margin
Amount of increased noise that can be tolerated while maintaining the designed
BER (bit error rate). The SNR Margin is set by the Central Office DSLAM. If the
SNR Margin is increased, bit error rate performance will improve, but the data
rate will decrease. Conversely, if the SNR Margin is decreased, bit error rate
performance will decrease, but the data rate will increase.
Line
Attenuation
Attenuation is the decrease in magnitude of the ADSL line signal between the
transmitter (Central Office DSLAM) and the receiver (Client ADSL Modem),
measured in dB. It is measured by calculating the difference in dB between the
signal power level received at the Client ADSL modem and the reference signal
power level transmitted from the Central Office DSLAM.
Data Rate
This field displays the ADSL data rate.
Help
The Help tab will give basic information referring to various screens locted in the Router. To view a
specific section, click on its hyperlinked name. A new window of information will appear.
91
DSL-524T ADSL Router Manual
Figure 7- 7. Help Window
92
DSL-524T ADSL Router Manual
93
DSL-524T ADSL Router Manual
A
Technical Specifications
GENERAL
ADSL Standards
ANSI T1.413 Issue 2
ITU G.992.1 (G.dmt) AnnexA
ITU G.992.2 (G.lite) Annex A
ITU G.994.1 (G.hs)
Standards:
ADSL2 Standards
ITU G.992.3 (G.dmt.bis) Annex A
ITU G.992.4 (G.lite.bis) Annex A
ADSL Standards:
ITU G.992.5 Annex A
Protocols:
IEEE 802.1d Spanning Tree
TCP/UDP
ARP
RARP
ICMP
RFC1058 RIP v1
RFC1213 SNMP v1 & v2c
RFC1334 PAP
RFC1389 RIP v2
RFC1483/2684 Multiprotocol Encapsulation over ATM
Adaptation Layer 5
RFC1577 Classical IP over ATM
RFC1661 Point to Point Protocol
RFC1994 CHAP
RFC2131 DHCP Client / DHCP Server
RFC2364 PPP over ATM
RFC2516 PPP over Ethernet
Data Transfer
Rate:
G.dmt full rate downstream: up to 8 Mbps
G.dmt full rate upstream: up to 1 Mbps
G.lite: ADSL downstream up to 1.5 Mbps
G.lite: ADSL upstream up to 512 Kbps
G.dmt.bis full rate downstream: up to 12 Mbps
94
DSL-524T ADSL Router Manual
GENERAL
G.dmt.bis full rate upstream: up to 12 Mbps
ADSL full rate downstream: up to 24 Mbps
ADSL full rate upstream: up to 1 Mbps
Media
Interface:
ADSL interface: RJ-11 connector for connection to 26 AWG
twisted pair telephone line
LAN interface: RJ-45 port for 10/100BASE-T Ethernet
connection
Physical and Environmental
DC Inputs:
Power
Adapter:
Input: 120V AC 60Hz
Output: 12V AC, 1.2A
Power
Consumption
:
9 Watts (max)
Operating
Temperature:
0° to 40°C
Storage
Temperature
-20° to 70°C
Humidity:
5% to 95% (non-condensing)
Dimensions:
109 mm x 142.8 mm x 32.1 mm
Weight:
200 gm
EMI:
CE Class B, FCC Class B (Part 15)
Safety:
CSA 950, UL 1950, IEC 60950, EN 60950
Reliability:
Mean Time Between Failure (MTBF) min. 4 years
95
DSL-524T ADSL Router Manual
B
IP Address Setup
The DSL-524T is designed to provide network administrators maximum flexibility for IP addressing
on the Ethernet LAN. The easiest IP setup choice in most cases is to let the Router do it using DHCP,
which is enabled by default. This appendix briefly describes various options including DHCP, used for
IP setup on a LAN. If you are new to IP networking, the next appendix provides some background
information on basic IP concepts.
Assigning Network IP Addresses
The IP address settings, which include the IP address, subnet mask and gateway IP address are the first
and most important internal network settings that need to be configured. The Router is assigned a
default LAN IP address and subnet mask. If you do not have a preexisting IP network and are setting
one up now, using the factory default IP address settings can greatly ease the setup process. If you
already have a preexisting IP network, you can adjust the IP settings for the Router to fit within your
existing scheme.
Using the Default IP Address
The Router is shipped with a preset default IP address setting of 192.168.1.1 for the LAN port. There
are two ways to use this default IP address, you can manually assign an IP address and subnet mask
for each PC on the LAN or you can instruct the Router to automatically assign them using DHCP. The
simplest method is to use DHCP. The DHCP function is active by default.
Manual IP Address Assignment
Manually configuring IP settings for the LAN means you must manually set an IP address, subnet
mask and IP address of the default gateway (the Router’s IP address) on each networked computer.
The example listed below describes IP configuration for computers running Windows 95 or Windows
98. Regardless of what operating system is used on each workstation, the three network IP settings
must be defined so the network interface used by each workstation can be identified by the Router, and
vice versa. For detailed information about configuring your workstations IP settings, consult the user’s
guide included with the operating system or the network interface card (NIC).
1. In Windows 95/98, click on the Start button, go to Settings and choose Control Panel.
2. In the window that opens, double-click on the Network icon.
3. Under the Configuration tab, select the TCP/IP component and click Properties.
4. Choose the Specify an IP address option and edit the address settings accordingly. Consult the
table below for IP settings on a Class C network.
IP Setup - Example #1
Using Default IP without DHCP
Host
IP Address
Subnet Mask Gateway
IP
Router
192.168.1.1
255.255.255.0
96
DSL-524T ADSL Router Manual
Computer
#1
192.168.1.2
255.255.255.0
192.168.1.1
Computer
#2
192.168.1.3
255.255.255.0
192.168.1.1
Computer
#3
192.168.1.4
255.255.255.0
192.168.1.1
Please note that when using the default IP address as in the above example, the first three numbers in
the IP address must always be the same with only the fourth number changing. The first three numbers
define the network IP address (all machines must belong to the same IP network), while the last
number denotes the host IP address (each computer must have a unique address to distinguish it on the
network). The IP address scheme used in Example #1 can be used for any LAN that requires up to 253
separate IP addresses (excluding the Router). Notice that the subnet mask is the same for all machines
and the default gateway address is the LAN IP address of the Router.
It is a good idea to make a note of each device’s IP address for reference during troubleshooting or
when adding new stations or devices.
Using DHCP
The second way to use the default settings is to allow the Router to automatically assign IP settings for
workstation using DHCP. To do this, simply make sure your computers’ IP addresses are set to 0.0.0.0
(under Windows, choose the option Obtain an IP address automatically in the TCP/IP network
component described above). When the computers are restarted, their IP settings will automatically be
assigned by the Router. The Router is set by default to use DHCP. See the discussion in Chapter 5 for
information on how to use configure the Router for DHCP.
Changing the IP Address of the Router
When planning your LAN IP address setup, you may use any scheme allowed by rules that govern IP
assignment. It may be more convenient or easier to remember an IP scheme that use a different
address for the Router. Or you may be installing the Router on a network that has already established
the IP settings. Changing the IP address is a simple matter and can be done using the web manager
(see LAN IP Address in Chapter 5). If you are incorporating the Router into a LAN with an existing IP
structure, be sure to disable the DHCP function. Also, consider the effects of the NAT function which
is enable by default.
An IP addressing scheme commonly used for Ethernet LANs establishes 10.0.0.1 as the base address
for the network. Using Example #2 below, the Router is assigned the base address 10.0.0.1 and the
remaining addresses are assigned manually or using DHCP.
IP Setup - Example #2
Alternative IP Assignment
Host
IP Address
Subnet Mask Gateway
IP
Router
10.0.0.1
255.255.255.0
Computer
#1
10.0.0.2
255.255.255.0
97
10.0.0.1
DSL-524T ADSL Router Manual
Computer
#2
10.0.0.3
255.255.255.0
10.0.0.1
Computer
#3
10.0.0.4
255.255.255.0
10.0.0.1
These two examples are only examples you can use to help you get started. If you are interested in
more advanced information on how to use IP addressing on a LAN there are numerous resources
freely available on the Internet. There are also many books and chapters of books on the subject of IP
address assignment, IP networking and the TCP/IP protocol suite.
98
DSL-524T ADSL Router Manual
C
IP Concepts
This appendix describes some basic IP concepts, the TCP/IP addressing scheme and show how to
assign IP Addresses.
When setting up the Router, you must make sure it has a valid IP address. Even if you will not use the
WAN port (ADSL port), you should, at the very least, make sure the Ethernet LAN port is assigned a
valid IP address. This is required for telnet, in-band SNMP management, and related functions such as
“trap” handling and TFTP firmware download.
IP Addresses
The Internet Protocol (IP) was designed for routing data between network sites all over the world, and
was later adapted for routing data between networks within any site (often referred to as
“subnetworks” or “subnets”). IP includes a system by which a unique number can be assigned to each
of the millions of networks and each of the computers on those networks. Such a number is called an
IP address.
To make IP addresses easy to understand, the originators of IP adopted a system of representation
called “dotted decimal” or “dotted quad” notation. Below are examples of IP addresses written in this
format:
201.202.203.204
189.21.241.56
125.87.0.1
Each of the four values in an IP address is the ordinary decimal (base 10) representation of a value that
a computer can handle using eight “bits” (binary digits — 1s and 0s). The dots are simply convenient
visual separators.
Zeros are often used as placeholders in dotted decimal notation; 189.21.241.56 can therefore also
appear as 189.021.241.056.
IP networks are divided into three classes on the basis of size. A full IP address contains a network
portion and a “host” (device) portion. The network and host portions of the address are different
lengths for different classes of networks, as shown in the table below.
99
DSL-524T ADSL Router Manual
Networks attached to the Internet are assigned class types that determine the maximum number of
possible hosts per network. The previous figure illustrates how the net and host portions of the IP
address differ among the three classes. Class A is assigned to networks that have more than 65,535
hosts; Class B is for networks that have 256 to 65534 hosts; Class C is for networks with less than 256
hosts.
Class
A
B
Maximum
Number of
Networks in
Class
126
16,382
C
2,097,150
IP Network Classes
Network Addresses
(Host Portion in
Parenthesis)
Maximum Number of
Hosts per Network
1(.0.0.0) to 126(.0.0.0)
128.1(.0.0) to 191.254(
.0.0)
192.0.1(.0) to 223.255.254
(.0)
16,777,214
65,534
254
All network addresses outside of these ranges (Class D and E) are either reserved or
set aside for experimental networks or multicasting.
When an IP address's host portion contains only zero(s), the address identifies a network and not a host.
No physical device may be given such an address.
The network portion must start with a value from 1 to 126 or from 128 to 223. Any other value(s) in
the network portion may be from 0 to 255, except that in class B the network addresses 128.0.0.0 and
191.255.0.0 are reserved, and in class C the network addresses 192.0.0.0 and 223.255.255.0 are
reserved.
The value(s) in the host portion of a physical device's IP address can be in the range of 0 through 255
as long as this portion is not all-0 or all-255. Values outside the range of 0 to 255 can never appear in
an IP address (0 to 255 is the full range of integer values that can be expressed with eight bits).
The network portion must be the same for all the IP devices on a discrete physical network (a single
Ethernet LAN, for example, or a WAN link). The host portion must be different for each IP device —
or, to be more precise, each IP-capable port or interface — connected directly to that network.
The network portion of an IP address will be referred to in this manual as a network number; the host
portion will be referred to as a host number.
To connect to the Internet or to any private IP network that uses an Internet-assigned network number,
you must obtain a registered IP network number from an Internet-authorized network information
center. In many countries you must apply through a government agency, however they can usually be
obtained from your Internet Service Provider (ISP).
If your organization's networks are, and will always remain, a closed system with no connection to the
Internet or to any other IP network, you can choose your own network numbers as long as they
conform to the above rules.
If your networks are isolated from the Internet, e.g. only between your two branch offices, you can
assign any IP Addresses to hosts without problems. However, the Internet Assigned Numbers
Authority (IANA) has reserved the following three blocks of IP Addresses specifically for private
(stub) networks:
Note:
Clas
s
A
Beginning
Address
10.0.0.0
100
Ending
Address
10.255.255.25
5
DSL-524T ADSL Router Manual
B
172.16.0.0
C
192.168.0.0
172.31.255.25
5
192.168.255.2
55
It is recommended that you choose private network IP Addresses from the above list. For more
information on address assignment, refer to RFC 1597, Address Allocation for Private Internets and
RFC 1466, Guidelines for Management of IP Address Space.
101
DSL-524T ADSL Router Manual
Subnet Mask
In the absence of subnetworks, standard TCP/IP addressing may be used by specifying subnet masks
as shown below.
IP Class
Class A
Class B
Class C
Subnet Mask
255.0.0.0
255.255.0.0
255.255.255.0
Subnet mask settings other than those listed above add significance to the interpretation of bits in the
IP address. The bits of the subnet mask correspond directly to the bits of the IP address. Any bit and a
subnet mask that is to correspond to a net ID bit in the IP address must be set to 1.
102
DSL-524T ADSL Router Manual
D
Microfilters and Splitters
Most ADSL clients will be required to install a simple device that prevents the ADSL line from
interfering with regular telephone services. These devices are commonly referred to as microfilters or
sometimes called (inaccurately) line splitters. They are easy to install and use standard telephone
connectors and cable.
Some ADSL service providers will send a telecommunications technician to modify the telephone line,
usually at the point where the telephone line enters the building. If a technician has divided or split
your telephone line into two separate lines - one for regular telephone service and the other for
ADSL – then you do not need to use any type of filter device. Follow the instructions given to you by
your ADSL service provider about where and how you should connect the Router to the ADSL line.
Microfilters
Unless you are instructed to use a “line splitter” (see below), it will be necessary to install a microfilter
(low pass filter) device for each telephone or telephone device (answering machines, Faxes etc.) that
share the line with the ADSL service. Microfilters are easy-to-install, in-line devices, which attach to
the telephone cable between the telephone and wall jack. Microfilters that install behind the wall plate
are also available. A typical in-line microfilter installation is shown in the diagram below.
Microfilter Installation
Important: Do not install the microfilter between the Router and the telephone jack. Microfilters are
only intended for use with regular telephones, Fax machines and other regular telephone devices.
103
DSL-524T ADSL Router Manual
Line Splitter
If you are instructed to use a “line splitter”, you must install the device between the Router and the
phone jack. Use standard telephone cable with standard RJ-11 connectors. The splitter has three RJ-11
ports used to connect to the wall jack, the Router and if desired, a telephone or telephone device. The
connection ports are typically labeled as follows:
Line - This port connects to the wall jack.
ADSL – This port connects to the Router.
Phone – This port connects to a telephone or other telephone device.
The diagram below illustrates the proper use of the splitter.
Line Splitter Installation
104
International Offices
U.S.A
17595 Mt. Herrmann Street
Fountain Valley, CA. 92708
TEL: 714-885-6000
Fax 866-743-4905
URL: www.dlink.com
Canada
2180 Winston Park Drive
Oakville, Ontario, L6H 5W1
Canada
TEL: 1-905-8295033
FAX: 1-905-8295223
URL: www.dlink.ca
Norway
Karihaugveien 89
1086 Oslo
Norway
TEL: 47-23-897189
FAX: 47-22-309085
URL: www.dlink.no
Finland
Pakkalankuja 7A
01510 Vantaa,
Finland
TEL : +358-9-2707 5080
FAX: + 358-9-2707 5081
URL: www.dlink.fi
Europe (U. K.)
4th Floor, Merit House
Edgware Road, Colindale
London NW9 5AB
U.K.
TEL: 44-20-8731-5555
FAX: 44-20-8731-5511
URL: www.dlink.co.uk
Iberia
C/Sabino De Arana,
56 Bajos
08028 Barcelona
TEL: 34 93 4090770
FAX: 34 93 4910795
URL: www.dlinkiberia.es
Germany
Schwalbacher Strasse 74
D-65760 Eschborn
Germany
TEL: 49-6196-77990
FAX: 49-6196-7799300
URL: www.dlink.de
Singapore
1 International Business Park
#03-12 The Synergy
Singapore 609917
TEL: 65-6774-6233
FAX: 65-6774-6322
URL: www.dlink-intl.com
France
Le Florilege #.2, Allee de la Fresnerie
78330 Fontenay le Fleury
France
TEL: 33-1-30238688
FAX: 33-1-30238689
URL: www.dlink-france.fr
Australia
1 Giffnock Avenue,
North Ryde, NSW 2113
Australia
TEL: 61-2-8899-1800
FAX: 61-2-8899-1868
URL: www.dlink.com.au
Netherlands
Weena 290
3012 NJ Rotterdam
Netherlands
Tel: +31-10-282-1445
Fax: +31-10-282-1331
URL: www.dlink-benelux.com
India
D-Link House, Kurla Bandra Complex
Road,
Off CST Road, Santacruz (East), Mumbai 400098.
India
TEL: 91-022-26526696/56902210
FAX: 91-022-26528914
URL: www.dlink.co.in
Belgium
Rue des Colonies 11
B-1000 Brussels
Belgium
Tel: +32(0)2 517 7111
Fax: +32(0)2 517 6500
URL: www.dlink-benelux.com
Italy
Via Nino Bonnet n. 6/b
20154 – Milano,
Italy
TEL: 39-02-2900-0676
FAX: 39-02-2900-1723
URL: www.dlink.it
Sweden
P.O. Box 15036, S-167 15 Bromma
Sweden
TEL: 46-(0)8564-61900
FAX: 46-(0)8564-61901
URL: www.dlink.se
Denmark
Naverland 2, DK-2600
Glostrup, Copenhagen,
TEL: 45-43-969040
FAX: 45-43-424347
URL:www.dlink.dk
Middle East (Dubai)
P.O.Box: 500376
Office No.:103, Building:3
Dubai Internet City
Dubai, United Arab Emirates
Tel:+971-4-3916480
Fax:+971-4-3908881
URL: www.dlink-me.com
Turkey
Regus Offices
Beybi Giz Plaza, Ayazaga Mah. Meydan
Sok. No:28
Maslak 34396, Istanbul-Turkiye
TEL: +90 212 335 2553
FAX: +90 212 335 2500
URL: www.dlink.com.tr
Egypt
19 El-Shahed Helmy, El Masri
Al-Maza, Heliopolis
Cairo,Egypt.
TEL:+202 414 4295
FAX:+202 415 6704
URL: www.dlink-me.com
Israel
11 Hamanofim Street
Ackerstein Towers, Regus Business Center
P.O.B 2148, Hertzelia-Pituach 46120.
Israel
TEL: +972-9-9715700
FAX: +972-9-9715601
URL: www.dlink.co.il
LatinAmerica
Isidora Goyeechea 2934 of 702,
Las Condes
Santiago – Chile S.A.
TEL: 56-2-232-3185
FAX: 56-2-232-0923
URL: www.dlink.cl
Brasil
Av das Nacoes Unidas,
11857 - 14 - andar - cj 141/142
Brooklin Novo
Sao Paulo - SP - Brazil
CEP 04578-000
TEL: +55 11 55039320
FAX: +55 11 55039322
URL: www.dlinkbrasil.com.br
South Africa
Einstein Park II
Block B
102-106 Witch-Hazel Avenue
Highveld Technopark
Centurion
Gauteng
Republic of South Africa
TEL: 27-12-665-2165
FAX: 27-12-665-2186
URL: www..d-link.co.za
Russia
Grafsky per., 14, floor 6
Moscow
129626 Russia
TEL: 7-095-744-0099
FAX: 7-095-744-0099 #350
URL: www.dlink.ru
China
No.202,C1 Building, Huitong Office Park,
No.71, Jianguo Road, Chaoyang District,
Beijing,
100025, China.
TEL +86-10-58635800
FAX: +86-10-58635799
URL: www.dlink.com.cn
Taiwan
2F, No. 119, Pao-Chung Rd.
Hsin-Tien, Taipei
Taiwan
TEL: 886-2-2910-2626
FAX: 886-2-2910-1515
URL: www.dlinktw.com.tw
Headquarters
2F, No. 233-2, Pao-Chiao Rd.
Hsin-Tien, Taipei
Taiwan
TEL: 886-2-2916-1600
FAX: 886-2-2914-6299
URL:www.dlink.com
Registration Card
Print, type or use block letters.
Your name: Mr./Ms__________________________________________________________________________
Organization: ____________________________________________Dept.______________________________
Your title at organization:_____________________________________________________________________
Telephone:_________________________________________ Fax:___________________________________
Organization's full address:___________________________________________________________________
_________________________________________________________________________________________
Country:__________________________________________________________________________________
Date of purchase (Month/Day/Year):_______________________________________
Product
Model
Product Serial No.
* Product installed in type of
computer (e.g., Compaq 486)
* Product installed in computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name:____________________________________________________________________________
Telephone:_________________________________________ Fax:___________________________________
Reseller's full address:_______________________________________________________________________
_________________________________________________________________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
Home Office Travel Company Business Home Business Personal Use
2. How many employees work at installation site?
1 employee 2-9 10-49 50-99 100-499 500-999 1000 or more
3. What network protocol(s) does your organization use ?
XNS/IPX TCP/IP DECnet Others_______________________________________________________
4. What network operating system(s) does your organization use ?
D-Link LANsmart Novell NetWare NetWare Lite SCO Unix/Xenix PC NFS 3Com 3+Open
Banyan Vines DECnet Pathwork Windows NT Windows NTAS Windows '95
Others________________________________________________________________________________
5. What network management program does your organization use ?
D-View HP OpenView/Windows HP OpenView/Unix SunNet Manager Novell NMS
NetView 6000 Others___________________________________________________________________
6. What network medium/media does your organization use ?
Fiber-optics Thick coax Ethernet Thin coax Ethernet 10BASE-T UTP/STP
100BASE-TX 100BASE-T4 100VGAnyLAN Others_________________________________________
7. What applications are used on your network?
Desktop publishing Spreadsheet Word processing CAD/CAM
Database management Accounting Others_________________________________________________
8. What category best describes your company?
Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate Manufacturing
Retail/Chainstore/Wholesale Government Transportation/Utilities/Communication VAR
System house/company Other____________________________________________________________
9. Would you recommend your D-Link product to a friend?
Yes No Don't know yet
10.Your comments on this product? _________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
_____________________________________________

Similar documents

×

Report this document